Search NASA⌕ Search

SEARCH · Search NASA

Results for “WING SPAN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1956

Finite Span Wings in Compressible Flow

Equations are developed using the source distribution method for the velocity potential function and pressure on thin wings in steady and unsteady motion. Closed form solutions are given for harmonically oscillating wings of general plan form including the effect of the wing wake. Some useful examples are presented in an appendix for arrow, semielliptical, and hexagonal plan form wings.

WINGS, ELLIPTICAL↗
NASA NTRS2016

Active Flow Control Using Sweeping Jet Actuators on a Semi-Span Wing Model

Wind tunnel experiments were performed using active flow control on an unswept semispan wing model with a 30% chord trailing edge flap to aid in the selection of actuators for a planned high Reynolds number experiment. Two sweeping jet actuator sizes were investigated to determine the influence of actuator size on the active flow control system efficiency. Sweeping jet actuators with orifice sizes of 1 mm x 2 mm and 2 mm x 4 mm were selected because of the differences in actuator jet sweep angle. The parameters that were varied include actuator momentum, freestream velocity, and trailing edge flap deflection angle. Steady and unsteady pressure data, Particle Image Velocimetry data, and force and moment data were acquired to assess the performance of the two actuators. In addition to the wind tunnel experiments, benchtop studies of the actuators were performed to characterize the jets produced by each actuator. Benchtop investigations of the smaller actuator reveal that the jet exiting the actuator has a reduced sweep angle compared to published data for larger versions of this type of actuator. The larger actuator produces an oscillating jet that attaches to the external di↵user walls at low supply pressures and produces the expected sweep angles. The AFC results using the smaller actuators show that while the actuators can control flow separation, the selected spacing of 3.3 cm may be too large due to the reduced sweep angle. In comparison, the spacing for the larger actuators, 6.6 cm, appears to be optimal for the Mach numbers investigated. Particle Image Velocimetry results are presented and show how the wall jets produced by the actuators cause the flow to attach to the flap surface.

Melton, LaTunia Pack↗
NASA NTRS1977

Wake Vortex Minimization

A status report is presented on research directed at reducing the vortex disturbances of aircraft wakes. The objective of such a reduction is to minimize the hazard to smaller aircraft that might encounter these wakes. Inviscid modeling was used to study trailing vortices and viscous effects were investigated. Laser velocimeters were utilized in the measurement of aircraft wakes. Flight and wind tunnel tests were performed on scale and full model scale aircraft of various design. Parameters investigated included the effect of wing span, wing flaps, spoilers, splines and engine thrust on vortex attenuation. Results indicate that vortives may be alleviated through aerodynamic means.

Source record↗
NASA NTRS1941

The calculation of span LCAD distributions of swept-back wings

Span load distributions of swept-back wings have been calculated. The method used was to replace the wing with a bound vortex at the quarter-chord line and to calculate the downwash due to the system of bound and trailing vortices to conform at the three-quarter-chord line to the slope of the flat-plate wing surface. Results are given for constant-chord and 5:1 tapered plan forms, for sweep-back angles of 0 degrees, 30 degrees, and 45 degrees, and for aspect ratios of 3, 6, and 9. Some comments on the stalling of swept-back wings are included.

Mutterperl, William↗
NASA NTRS1973

Laser Doppler velocimeter investigation of trailing vortices behind a semi-span swept wing in a landing configuration

Measured axial and tangential velocity profiles in the near wake vortices of a semi-span model of the Convair 990 wing in the NASA-Ames 7- by 10-foot wind tunnel are presented. A scanning laser Doppler velocimeter was used to obtain data at two different downstream stations (0.49 and 1.25 wing spans) at various angles of attack and configurations from wing alone to wing plus nacelles, anti-shock bodies, and flaps deflected 27 deg (landing configuration). It is shown that the velocity distributions within the wake are quite sensitive to span loading. Specifically, it is illustrated that an aircraft flying at given lift coefficient (C SUB L), can substantially reduce its trailing vortex upset potential by deploying its flaps and altering its flight attitude to maintain the same C SUB L. This might be taken into consideration along with performance and noise considerations in the selection of aircraft approach lift over drag.

Ciffone, D. L.↗
NASA NTRS1960

II. Aerodynamic research relative to variable-sweep multimission aircraft

The development of a multimission military aircraft would be highly desirable both from the standpoint of easing the strain on the national budget by reducing the number of aircraft types and of providing versatility which would increase the effectiveness of the aircraft in the performance of a given mission. Some of the capabilities which might be required of such an aircraft are shown in figure 1 along with their respective aerodynamic and configuration requirements. The first three capabilities are grouped together since they all require good subsonic characteristics. The first, a long loiter capability for combat air patrol and the second, a long ferry range for efficient aircraft deployment both require a high subsonic lift-drag ratio. The third capability, STOL, is desirable for carrier and short-field operation and requires the development of high lift. All three of these capabilities can best be obtained with a high-aspect-ratio wing having a large span and a low-sweep angle. The fourth capability is that of a high-altitude supersonic attack or intercept and requires a high lift-drag ratio at supersonic speeds which dictates a rather slender configuration with a moderate-span wing which is either very thin or highly swept. The fifth capability listed in figure 1 is that of a low-altitude high-speed attack that would increase the probability of long-range penetration of antiaircraft defenses. The high dynamic pressures encountered on the deck at high speeds require a low-lift-curve slope to reduce the gust-induced normal accelerations, and low friction and wave drag (drag due to lift is insignificant at high dynamic pressures) to assure sufficient speed and range. In order to best satisfy these requirements, a slender aircraft having little or no wing is required. It is apparent from figure 1 that these five capabilities are highly incompatible and that an efficient multimission aircraft will require a means of varying its aerodynamic characteristics. This can be best accomplished with some type of variable-wing geometry. There are, of course, several types of variable wing geometry. However, in view of the extremely large variations in wing span desired, variable wing sweep, as indicated In the lower right sketch of figure 1, appears to provide the best method. The Langley Research Center of the National Aeronautics and Space Administration has therefore initiated a research program to provide the aerodynamic information needed for the development of a variable-sweep multimission military aircraft, and it is the purpose of this paper to briefly describe some of the results of this program.

Military aircraft↗
NASA NTRS2007

Innovative Concept for a Heavy-Load Aircraft Utilizing a Two-Dimensional Wing

Heavy-load aircraft of conventional wing-body-tail design have become very large. Excessive size of such aircraft may present problems in the manufacturing process. In addition, large wing spans may cause some difficulties in ground handling. Increasing lift loads on large span cantilever wings will also increase the strength of the wing tip vortex. The concept presented herein proposes a means for substantially increasing the lift load capability of an aircraft without increasing the overall length and span of the configuration. The concept has a rectangular wing with a relatively low span and a large chord to provide the area required for high lift. Large fuselages are attached at each wing tip to provide the volume required for heavy loading. The fuselages serve as endplates for the wing and should preclude tip flow so that two-dimensional flow might be established on the wing. Elimination of the wing tip flow should prevent the formation of a tip vortex and eliminate the tip vortex hazard to trailing aircraft. Exploratory wind tunnel tests of such an aircraft concept have been conducted. Lessons learned from these tests are discussed herein in an effort to determine the validity of the concept.

Spearman, M. Leroy↗
NASA NTRS1976

Numerical studies of three-dimensional breakdown in trailing vortex wakes

The development of dangerous vortex wakes trailing between aircraft for appreciable distance downstream, and posing hazards to following aircraft, is calculated using finite-element three-dimensional relaxation methods. Near-wake, middle-wake, and far-wake conditions are delineated. Vortex system finite lifetimes can be calculated with greater facility owing to the inclusion of a self-induction term in the solution dependent upon local curvature and vortex core radius. Looping and convergence phenomena are studied for single vortex pairs, twin pairs, and multiple pairs. Proportions of flap span and wing span are shown to affect the time to convergence of vortex pairs. The self-induction term renders the convergence time of vortices a sensitive function of wavelength. Wakes trailing between wide-body ('Jumbo') aircraft are also examined.

Hackett, J. E.↗
NASA NTRS1976

Effect of drooped-nose flaps on the experimental force and moment characteristics of an oblique wing

Six-component experimental force and moment data are presented for a low aspect ratio, oblique wing equipped with drooped-nose flaps and mounted on top of a body of revolution. These flaps were investigated on the downstream wing panel with the nose drooped 5 deg, 10 deg, 20 deg, and 30 deg, and on both wing panels with the nose drooped 30 deg. It was to determine if such flaps would make the moment curves more linear by controlling the flow separation on the downstream wing panel at high lift coefficients. The wing was elliptical in planform and had an aspect ratio of 6.0 (based on the unswept wing span). The wing was tested at sweep angles of 45 deg and 50 deg throughout the Mach number range from 0.25 to 0.95. The drooped-nose flaps alone were not effective in making the moment curves more linear; however, a previous study showed that Kruger nose flaps improved the linearity of the moment curves when the Kruger flaps were used on only the downstream wing panel equipped with drooped-nose flaps deflected 5 deg.

Hopkins, E. J.↗