Search NASA⌕ Search

SEARCH · Search NASA

Results for “WING STALL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1966

Descent capability of two-propeller tilt-wing configurations

The wing stall problem encountered with tilt-wing V/STOL designs during low-powered descent flight conditions has led to buffeting which adversely affects both performance and handling qualities. The results of tests conducted in the Langley full-scale wind tunnel with a large semi­span model of a two-propeller tilt-wing configuration have indicated that three important factors provide substantial improvement in in the wing stall characteristics with consequent improvement in descent capability: down­-at-center propeller rotation resulted in delayed inboard stalling and pro­vided far better descent capability than the up-at-center rotation, moderate lowering of the propeller position relative to the wing chord provided further improvement in descent capability, and some flap deflec­tion was absolutely essential in order to have any descent capability for low-powered flight conditions. Use of all three factors should provide good descent capability even without the complexity of other sophisticated stall control devices.

WING STALL↗
NASA NTRS2007

Free-to-Roll Testing of Airplane Models in Wind Tunnels

A free-to-roll (FTR) test technique and test rig make it possible to evaluate both the transonic performance and the wingdrop/ rock behavior of a high-strength airplane model in a single wind-tunnel entry. The free-to-roll test technique is a single degree-of-motion method in which the model is free to roll about the longitudinal axis. The rolling motion is observed, recorded, and analyzed to gain insight into wing-drop/rock behavior. Wing-drop/rock is one of several phenomena symptomatic of abrupt wing stall. FTR testing was developed as part of the NASA/Navy Abrupt Wing Stall Program, which was established for the purposes of understanding and preventing significant unexpected and uncommanded (thus, highly undesirable) lateral-directional motions associated with wing-drop/rock, which have been observed mostly in fighter airplanes under high-subsonic and transonic maneuvering conditions. Before FTR testing became available, wingrock/ drop behavior of high-performance airplanes undergoing development was not recognized until flight testing. FTR testing is a reliable means of detecting, and evaluating design modifications for reducing or preventing, very complex abrupt wing stall phenomena in a ground facility prior to flight testing. The FTR test rig was designed to replace an older sting attachment butt, such that a model with its force balance and support sting could freely rotate about the longitudinal axis. The rig (see figure) includes a rotary head supported in a stationary head with a forward spherical roller bearing and an aft needle bearing. Rotation is amplified by a set of gears and measured by a shaft-angle resolver; the roll angle can be resolved to within 0.067 degrees at a rotational speed up to 1,000 degrees/s. An assembly of electrically actuated brakes between the rotary and stationary heads can be used to hold the model against a rolling torque at a commanded roll angle. When static testing is required, a locking bar is used to fix the rotating head rigidly to the stationary head. Switching between the static and FTR test modes takes only about 30 minutes. The FTR test rig was originally mounted in a 16-ft (approximately 4.0-m) transonic wind tunnel, but could just as well be adapted to use in any large wind tunnel. In one series of tests on the FTR rig, static and dynamic characteristics of models of four different fighter airplanes were measured. Two of the models exhibited uncommanded lateral motions; the other two did not. A figure of merit was developed to discern the severity of lateral motions. Using this figure of merit, it was shown that the FTR test technique enabled identification of conditions under which the uncommanded lateral motions occurred. The wind-tunnel conditions thus identified were found to be correlated with flight conditions under which the corresponding full-size airplanes exhibited uncommanded lateral motions.

Capone, Francis J.↗
NASA NTRS1976

Effect of wing bend on the experimental force and moment characteristics of an oblique wing

Static longitudinal and lateral/directional force and moment characteristics are presented for an elliptical oblique wing mounted on top of a Sears-Haack body of revolution. The wing had an aspect ratio of 6 (based on the unswept span) and was tested at various sweep angles relative to the body axis ranging from 0 to 60 deg. In an attempt to create more symmetrical spanwise wing stalling characteristics, both wing panels were bent upward to produce washout on the trailing wing panel and washing on the leading wing panel. Small fluorescent tufts were attached to the wing surface to indicate the stall progression on the wing. The tests were conducted throughout a Mach number range from 0.6 to 1.4 at a constant unit Reynolds number of 8.2 x 10 per meter. The test results indicate that upward bending of the wing panels had only a small effect on the linearity of the moment curves and would require an impractical wing-pivot location at low lift to eliminate the rolling moment resulting from this bending.

Hopkins, E. J.↗
NASA NTRS1961

Aerodynamic Characteristics of Propeller-Driven VTOL Aircraft

This paper discusses the two major configurations that are usually considered for achieving VTOL while keeping the fuselage essentially horizontal - that is, the tilt-wing and the deflected-slipstream configurations. Because of the high turning losses incurred by deflected-slipstream configurations in hovering and because of the wing-stalling problem of the pure tilt-wing configurations during the transition, it appears that a combination of the two principles should be used. This tilt-wing and flap configuration should make use of a programmed extensible-chord slotted flap together with a leading-edge high-lift device in order to avoid the performance and handling qualities problems associated with wing stalling during the transition while keeping the wing area as low as possible for efficiency in cruising flight.

Kirby, Robert H.↗
NASA NTRS2004

Transonic Free-To-Roll Analysis of the F/A-18E and F-35 Configurations

The free-to-roll technique is used as a tool for predicting areas of uncommanded lateral motions. Recently, the NASA/Navy/Air Force Abrupt Wing Stall Program extended the use of this technique to the transonic speed regime. Using this technique, this paper evaluates various wing configurations on the pre-production F/A-18E aircraft and the Joint Strike Fighter (F-35) aircraft. The configurations investigated include leading and trailing edge flap deflections, fences, leading edge flap gap seals, and vortex generators. These tests were conducted in the NASA Langley 16-Foot Transonic Tunnel. The analysis used a modification of a figure-of-merit developed during the Abrupt Wing Stall Program to discern configuration effects. The results showed how the figure-of-merit can be used to schedule wing flap deflections to avoid areas of uncommanded lateral motion. The analysis also used both static and dynamic wind tunnel data to provide insight into the uncommanded lateral behavior. The dynamic data was extracted from the time history data using parameter identification techniques. In general, modifications to the pre-production F/A-18E resulted in shifts in angle-of-attack where uncommanded lateral activity occurred. Sealing the gap between the inboard and outboard leading-edge flaps on the Navy version of the F-35 eliminated uncommanded lateral activity or delayed the activity to a higher angle-of-attack.

Owens, D. Bruce↗
NASA NTRS1984

Engineering analysis of drooped leading-edge wings near stall

Numerical results obtained with a three-dimensional vortex panel computer program for the calculation of inviscid, incompressible (potential) flow over infinitely thin finite wings with camber are presented. The program, which is designed for wings with drooped leading edge discontinuities, is essentially a numerical representation of lifting surface theory, involving both spanwise and chordwise distributions of vorticity. The results also include two engineering approximations. First, the effect of the leading-edge discontinuities is modeled by assuming that the vortices emanating from the discontinuities aerodynamically divide the wing into three distinct sections of lower aspect ratio. Secondly, the effect of the separated flow at high angle of attack is modeled by applying rectangular vortex panels with a varying vortex strength over the portions of the wing with attached flow.

Anderson, J. D., Jr.↗
DOE OSTI2023

Review of rotating wing dynamic stall: Experiments and flow control

Dynamic stall has been a technical challenge and a fluid dynamical subject of interest for more than fifty years; but in the last decade significant advances have been made in the understanding, prediction, modeling, and control of dynamic stall on rotors. This paper provides a summary of the state of the art of dynamic stall experiments and future directions in the understanding of dynamic stall on rotors. Experimental data sets are discussed, as well the direction of future research for control of dynamic stall. Coordinated testing between airfoils and rotating blades, as well as close integration between computational and experimental studies were found to be productive approaches. Advanced analysis methods, including statistical methods, modal representations, and artificial intelligence methods have led to significant advances in the understanding of dynamic stall. Investigations of dynamic stall control devices have allowed many useful targeted investigations of the transition to separated flow, but have not yet resulted in a commercially implemented device.

42 ENGINEERING↗
NASA NTRS1952

Flight Characteristics of a 1/4-Scale Model of the XFV-1 Airplane (TED No. NACA DE-378)

A l/4-scale dynamically similar model of the XFV-1 airplane has been flown in the Ames 40- by 80-foot wind tunnel, using the trailing flight-cable technique. This investigation was devoted to establishing the flight characteristics of the model in forward flight from hovering to wing stall, and in yawed flight (wing span alined with the relative wind) from hovering to the maximum speed at which controlled flight could be maintained. Landings, take-offs, and hovering characteristics in flights close to the ground were also investigated.. Since the remote control system for the model was rather complicated and provided artificial damping about the pitch, roll, and yaw axes, sufficient data from the control-system calibration tests are included in this report to specify the performance of the control system in relation to both the model flight tests and the design of an automatic control system for the full-scale airplane. The model in hovering flight appeared to be neutrally stable. The response of the model to the controls was very rapid, and it was always necessary to provide some amount of artificial damping to maintain control. The model could be landed with little difficulty by hovering approximately a foot above the floor and then cutting the power. Take-offs were more difficult to perform, primarily because the rate of change in power to the model motors was limited by the characteristics of the available power source. The model was,capable of controlled yawed flight at translational velocities up to and including 20 feet per second. The effectiveness of the controls decreased with increasing speed, however, and at 25 fps control in pitch, and probably roll, was lost completely. The model was flown in controlled forward flight from hovering up to 70 fps. During these flights the model appeared to be more difficult to control in yaw than it was in pitch or roll. The flights of the model were recorded by motion picture cameras. These motion pictures are available on loan from NACA Headquarters as a film supplement to this report.

Kelly, Mark W.↗
NASA NTRS2003

Iced Aircraft Flight Data for Flight Simulator Validation

NASA is developing and validating technology to incorporate aircraft icing effects into a flight training device concept demonstrator. Flight simulation models of a DHC-6 Twin Otter were developed from wind tunnel data using a subscale, complete aircraft model with and without simulated ice, and from previously acquired flight data. The validation of the simulation models required additional aircraft response time histories of the airplane configured with simulated ice similar to the subscale model testing. Therefore, a flight test was conducted using the NASA Twin Otter Icing Research Aircraft. Over 500 maneuvers of various types were conducted in this flight test. The validation data consisted of aircraft state parameters, pilot inputs, propulsion, weight, center of gravity, and moments of inertia with the airplane configured with different amounts of simulated ice. Emphasis was made to acquire data at wing stall and tailplane stall since these events are of primary interest to model accurately in the flight training device. Analyses of several datasets are described regarding wing and tailplane stall. Key findings from these analyses are that the simulated wing ice shapes significantly reduced the C , max, while the simulated tail ice caused elevator control force anomalies and tailplane stall when flaps were deflected 30 deg or greater. This effectively reduced the safe operating margins between iced wing and iced tail stall as flap deflection and thrust were increased. This flight test demonstrated that the critical aspects to be modeled in the icing effects flight training device include: iced wing and tail stall speeds, flap and thrust effects, control forces, and control effectiveness.

Ratvasky, Thomas P.↗
NASA NTRS1949

Wind-Tunnel Tests of a 0.16-Scale Model of the Douglas MX-656 Airplane at High Subsonic Speeds. II - Wing and Fuselage Pressure Distribution

Measurements of wing and fuselage pressure distributions were made at low and high subsonic Much numbers on a 0.16-scale model of the projected MX-656 research airplane. The MX-656 is a supersonic design utilizing a low-aspect-ratio wing and tail. Pressure-distribution measurements indicated that, although the critical Mach number of the wing was approximately 0.81 at 0 degree angle of attack, compressibility effects were of little significance below a Mach number of at least 0.90. The principal effect of compressibility was an increase in the pressure gradient over the after 30 percent of the wing chord, causing a tendency for the flow to separate. At 0.40 Mach number, the wing stalled abruptly at approximately 12 deg, angle of attack. The wing-pressure distribution showed this stall was a result of complete separation of the flow from the upper surface of the wing, Deflecting the leading-edge flaps delayed the stall to a higher angle of attack with some increase in the maximum section normal force,

Cleary, Joseph W.↗
NASA NTRS1961

Static Lateral Characteristics at High Subsonic Speeds of a Complete Airplane Model with a Highly Tapered Wing having the 0.80 Chord Line Unswept and with Several Tail Configurations

An investigation was made at high subsonic speeds of a complete model having a highly tapered wing and several tail configurations. The aspect-ratio-3.50 wing had a taper ratio of 0.067 and an unswept 0.80 chord line. The complete model was tested with a wing-chord-plane tail, a T-tail, and a biplane tail (combined T-tail and wing-chord-plane tail). The model was tested in the Langley high-speed 7- by 10-foot tunnel at Mach numbers from 0.60 to 0.92 over a range of angle of attack of about +/- 20 deg. and a range of sideslip of -15 deg. to 13 deg. Some data were obtained with the horizontal stabilizer deflected. A few tests were also made with the wing tips clipped to an aspect ratio of 3.00. The data show that shock-interference effects between the tail surfaces (T-tail) can have considerable influence on the directional stability and effective dihedral. For example, the T-tail configuration with horizontal-tail leading-edge overhang showed a considerable loss in directional stability as the angle of attack was reduced to zero or negative values; whereas, the T-tail with zero leading-edge overhang showed the loss to be considerably less. The directional stability of the model with the low tail was essentially constant over a range of angle of attack of +/- 50 deg. All configurations tested showed a large reduction in stability at positive and negative angles of attack larger than about 15 deg., probably because of adverse sidewash associated with wing stall. The data show that a wing-chord-plane horizontal tail (low tail) tends to give a positive pitching-moment increment with increase in sideslip angle; whereas, a high tail (T-tail) tends to give negative increments in pitching moment.

Goodson, Kenneth W.↗
NASA NTRS1983

An application of parameter identification to the oscillatory motion of an airplane at high C(L)

This paper presents an application of a stepwise regression incorporating polynomial splines to oscillatory flight data from a light research airplane operating at near stall angles of attack. It is shown that data from several experiments can be combined into a large data set for analysis and that hysteresis phenomena can be observed in this large data set. Finally, it is postulated from the analysis of the flight data and theoretical calculations that the observed oscillatory motion is the result of a combination of wing stall and wing wake position at the tail.

Batterson, J. G.↗
NASA NTRS1977

Investigation of a stall deterrent system utilizing an acoustic stall sensor

A simple rugged acoustic stall sensor which has an output proportional to angle of attack near wing stall has been evaluated on a Cessna 319 aircraft. A sensor position has been found on the wing where the sensor output is only slightly affected by engine power level, yaw angle, flap position and wing roughness. The NASA LRC General Aviation Simulator has been used to evaluate the acoustic sensor output as a control signal for active stall deterrent systems. It has been found that a simple control algorithm is sufficient for stall deterrence.

Bennett, A. G.↗
NASA NTRS1973

Experimental study of flow about a stalled two-dimensional airfoil

Wind tunnel tests to determine the flow characteristics of a stalled wing are described. The advantages of the plane wing over the ring wing for wind tunnel investigations are presented. The general flow pattern for stalled ring airfoils is developed. Photographs of the test equipment and installation are provided.

Coles, D. E.↗
NASA NTRS1987

Wind-tunnel investigation of a full-scale general aviation airplane equipped with an advanced natural laminar flow wing

An investigation was conducted in the Langley 30- by 60-Foot Wind Tunnel to evaluate the performance, stability, and control characteristics of a full-scale general aviation airplane equipped with an advanced laminar flow wing. The study focused on the effects of natural laminar flow and advanced boundary layer transition on performance, stability, and control, and also on the effects of several wing leading edge modifications on the stall/departure resistance of the configuration. Data were measured over an angle-of-attack range from -6 to 40 deg and an angle-of-sideslip range from -6 to 20 deg. The Reynolds number was varied from 1.4 to 2.4 x 10 to the 6th power based on the mean aerodynamic chord. Additional measurements were made using hot-film and sublimating chemical techniques to determine the condition of the wing boundary layer, and wool tufts were used to study the wing stall characteristics. The investigation showed that large regions of natural laminar flow existed on the wing which would significantly enhance cruise performance. Also, because of the characteristics of the airfoil section, artificially tripping the wing boundary layer to a turbulent condition did not significantly effect the lift, stability, and control characteristics. The addition of a leading-edge droop arrangement was found to increase the stall angle of attack at the wingtips and, therefore, was considered to be effective in improving the stall/departure resistance of the configuration. Also the addition of the droop arrangement resulted in only minor increases in drag.

Murri, Daniel G.↗
NASA NTRS1987

Wind-tunnel investigation of a general aviation airplane equipped with a high aspect-ratio, natural laminar-flow wing

A wind tunnel investigation has been conducted to evaluate the aerodynamic performance, stability, and control characteristics of a full-scale general aviation aircraft equipped with an advanced natural laminar flow wing. Force and moment data were measured over wide angle-of-attack and sideslip ranges and at Reynolds numbers from 1.4 million to 2.4 million based on the mean aerodynamic chord. Additional measurements determined the condition of the wing boundary layer and the wing stalling characteristics. The results showed that large regions of natural laminar flow existed on the wing which would significantly enhance the cruise performance of the configuration. Artificially tripping the boundary layer did not significantly affect the lift, stability, and control characteristics. Leading-edge modifications were effective in improving the stall resistance of the configuration, and resulted in only minor penalties in calculated cruise performance.

Murri, Daniel G.↗