Search NASA⌕ Search

SEARCH · Search NASA

Results for “WINGS - ASPECT RATIO, LARGE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

The quiet short-haul research aircraft

The design concepts, performance capabilities, and projected applications of the Quiet Short-Haul Research Aircraft (QSRA) are discussed. The propulsive lift system of the QSRA provides the lift required for short field operations at low community noise levels. This system consists of four high bipass ratio, geared turbofan engines mounted so that the engine exhaust flows across the upper surface of the wing (upper surface blowing). Large specially shaped flaps behind each engine control the direction of the flow for each phase of flight. A 95 passenger short haul transport based on this technology could operate out of a 2500 foot runway with a combined takeoff and landing 90 EPNdB footprint area of 2.7 sq mi.

Cochrane, J. A.↗
NASA NTRS1974

Effect of inlet ingestion of a wing tip vortex on turbojet stall margin

A two-dimensional inlet and a turbojet engine were investigated in a Mach 0.4 stream so as to ingest the tip vortex of a forward mounted wing. Results show that ingestion of a wing tip vortex by a turbojet engine can cause a large reduction in engine stall margin. The loss in stall compressor pressure ratio was primarily dependent on vortex location and rotational direction and not on total-pressure variations across the compressor face.

Mitchell, G. A.↗
NASA NTRS1975

Effect of inlet ingestion of a wing tip vortex on compressor face flow and turbojet stall margin

A two-dimensional inlet was alternately mated to a coldpipe plug assembly and a J85-GE-13 turbojet engine, and placed in a Mach 0.4 stream so as to ingest the tip vortex of a forward mounted wing. Vortex properties were measured just forward of the inlet and at the compressor face. Results show that ingestion of a wing tip vortex by a turbojet engine can cause a large reduction in engine stall margin. The loss in stall compressor pressure ratio was primarily dependent on vortex location and rotational direction and not on total-pressure distortion.

Mitchell, G. A.↗
NASA NTRSDate not supplied

Conceptual Design of a Gulled-Wing Commercial Transport

Open rotor powerplants have long been discussed as a potential solution to reduce aircraft fuel burn by increasing effective bypass ratio. However, this promising technology presents unique integration challenges. A gulled-wing approach for commercial transports is proposed to accommodate large-diameter powerplants. Integration effects of open rotor powerplants are modeled, analyzed, and discussed. Aerodynamic analysis and refined structural weight estimates are used to inform a preliminary conceptual design. Mission analysis of this model is performed, and the results are compared against NASA’s 154-passenger N+3 Conventional Configuration advanced technology baseline. Results indicate that gulled wings prove a viable solution for integrating large powerplants. Application of an open rotor engine model resulted in a fuel burn benefit on the order of 15% compared to the conventional turbofan configuration.

Conceptual Design↗
NASA NTRS1980

On the stability of three-dimensional compressible nonparallel boundary layers

A compressible linear stability theory is presented for three-dimensional nonuniform boundary layers. The amplitude, phase, and wavenumber equations which govern the motion of the disturbance are obtained by using the method of multiple scales. Group velocity trajectories are used to identify the disturbance growth direction. The spatial stability theory is applied to the flow on a laminar flow control supercritical sweptback wing of infinite span. Three different methods are used to calculate the absolute maximum logarithmic amplitude ratio N. In the front crossflow instability region, the method of maximum spatial growth rate predicts large difference in N compared with the method of fixed wavelength and the method of fixed spanwise component of wavelength. This difference decreases in the middle streamwise instability region, and almost vanishes in the rear crossflow instability region. Compressibility of the medium reduces N by about 15% in both the front and rear regions, and by about 40% in the middle region of the wing. Nonuniformity of the medium has large effects specially in the rear region.

El-Hady, N. M.↗
NASA NTRS1993

Navier-Stokes flowfield computation of wing/rotor interaction for a tilt rotor aircraft in hover

The download on the wing produced by the rotor-induced downwash of a tilt rotor aircraft in hover is of major concern because of its severe impact on payload-carrying capability. A method has been developed to help gain a better understanding of the fundamental fluid dynamics that causes this download, and to help find ways to reduce it. In particular, the method is employed in this work to analyze the effect of a tangential leading edge circulation-control jet on download reduction. Because of the complexities associated with modeling the complete configuration, this work focuses specifically on the wing/rotor interaction of a tilt rotor aircraft in hover. The three-dimensional, unsteady, thin-layer compressible Navier-Stokes equations are solved using a time-accurate, implicit, finite difference scheme that employs LU-ADI factorization. The rotor is modeled as an actuator disk which imparts both a radical and an azimuthal distribution of pressure rise and swirl to the flowfield. A momentum theory blade element analysis of the rotor is incorporated into the Navier-Stokes solution method. Solution blanking at interior points of the mesh has been shown here to be an effective technique in introducing the effects of the rotor and tangential leading edge jet. Results are presented both for a rotor alone and for wing/rotor interaction. The overall mean characteristics of the rotor flowfield are computed including the flow acceleration through the rotor disk, the axial and swirl velocities in the rotor downwash, and the slipstream contraction. Many of the complex tilt rotor flow features are captured including the highly three-dimensional flow over the wing, the recirculation fountain at the plane of symmetry, wing leading and trailing edge separation, and the large region of separated flow beneath the wing. Mean wing surface pressures compare fairly well with available experimental data, but the time-averaged download/thrust ratio is 20-30 percent higher than the measured value. The discrepancy is due to a combination of factors that are discussed. Leading edge tangential blowing, of constant strength along the wing span, is shown to be effective in reducing download. The jet serves primarily to reduce the pressure on the wing upper surface. The computation clearly shows that, because of the three-dimensionality of the flowfield, optimum blowing would involve a spanwise variation in blowing strength.

Fejtek, Ian G.↗
NASA NTRS2003

Vortex Core Size in the Rotor Near-Wake

Using a kinetic energy conservation approach, a number of simple analytic expressions are derived for estimating the core size of tip vortices in the near-wake of rotors in hover and axial-flow flight. The influence of thrust, induced power losses, advance ratio, and vortex structure on rotor vortex core size is assessed. Experimental data from the literature is compared to the analytical results derived in this paper. In general, three conclusions can be drawn from the work in this paper. First, the greater the rotor thrust, t h e larger the vortex core size in the rotor near-wake. Second, the more efficient a rotor is with respect to induced power losses, the smaller the resulting vortex core size. Third, and lastly, vortex core size initially decreases for low axial-flow advance ratios, but for large advance ratios core size asymptotically increases to a nominal upper limit. Insights gained from this work should enable improved modeling of rotary-wing aerodynamics, as well as provide a framework for improved experimental investigations of rotor a n d advanced propeller wakes.

Young, Larry A.↗
NASA NTRS1961

Aerodynamic Characteristics in Pitch of a Series of Cruciform-Wing Missiles with Canard Controls at a Mach Number of 2.01

An investigation has been conducted in the Langley 4- by 4-foot supersonic pressure tunnel at a Mach number of 2.01 to determine the static longitudinal stability and control characteristics of a series of missile configurations with canard controls at angles of attack up to about 28 deg. The missiles had cruciform wings and canard surfaces of delta plan form with 70 deg.swept leading edges. Five bodies having fineness ratios of 19.1, 17.7, 16.7, 15.7, and 14.8 were investigated. The results of the investigation indicated a large nonlinear variation of pitching moment with angle of attack for the body of largest fineness ratio that was progressively reduced by decreasing the fineness ratio until it was essentially eliminated for a body of fineness ratio 14.8. The increased linearity of the moment curve would make it possible to reduce the margin of stability so that, for a given canard size and deflection, a higher trim angle of attack might be obtained for the shortest missile than for the longest missile. The pitching-moment results indicated that methods of prediction which assumed linear variations with angle of attack for the wing-alone and wing-plus-interference characteristics were adequate for angles of attack up to about 12 deg. At higher angles of attack it was evident that the characteristics of these components were nonlinear and that more refined methods would be required for adequate prediction.

Spearman, M. Leroy↗
NASA NTRS1972

An analysis of the takeoff and landing performance of a jet-powered STOL augmentor wing design

A preliminary study of the takeoff and landing performance characteristics of a swept wing airplane with augmented jet flap, designed for STOL operation and low noise is presented. The study is based on aerodynamic data from wind tunnel tests of a large-scale swept augmentor wing model, scaled up to a 48,000 pound airplane. Engine characteristics are based on a turbo fan with a fan pressure ratio of 2.5 delivering the major portion of the thrust to the augmentor flap. A description of the overall airplane configuration, the propulsion system, and the use of the aerodynamics is presented. To assess the STOL performance of the airplane, takeoff and landing distances and flight path capabilities were computed at various flap deflections and thrust levels. After evaluating these results in terms of desired STOL performance with required margins, basic takeoff and landing configurations were chosen.

Post, S. E.↗
NASA NTRS1993

Aerodynamic configuration design using response surface methodology analysis

An investigation has been conducted to determine a set of optimal design parameters for a single-stage-to-orbit reentry vehicle. Several configuration geometry parameters which had a large impact on the entry vehicle flying characteristics were selected as design variables: the fuselage fineness ratio, the nose to body length ratio, the nose camber value, the wing planform area scale factor, and the wing location. The optimal geometry parameter values were chosen using a response surface methodology (RSM) technique which allowed for a minimum dry weight configuration design that met a set of aerodynamic performance constraints on the landing speed, and on the subsonic, supersonic, and hypersonic trim and stability levels. The RSM technique utilized, specifically the central composite design method, is presented, along with the general vehicle conceptual design process. Results are presented for an optimized configuration along with several design trade cases.

Engelund, Walter C.↗
NASA NTRS1946

High-Speed Longitudinal-Stability and Control Characteristics of the Consolidated Vultee Lark Missile as Predicted from Wind-Tunnel Tests (TED No. NACA 2391)

A high-speed wind-tunnel investigation of the aerodynamic characteristics of a full-scale model of the Consolidated Vultee Lark indicates that the missile possesses satisfactory longitudinal-stability and-control characteristics throughout the Mach number range from 0.2 to 0.85, but that the maximum lift coefficients developed are not high enough to insure interception of the target at high altitudes. A reduction in wing loading appears advisable. Although the static longitudinal stability at zero angle of attack changes with Mach number and with lift coefficient, satisfactory control should be possible at all times as the tails retain their relatively large effectiveness throughout the range of Mach numbers and lift coefficients tested. Minimum stability and maximum maneuverability occur around 0.80 Mach number and 0.2 lift coefficient, which corresponds to level flight conditions of the missile. The optimum ratio of tail-to-wing deflection is 0.4.

Axelson, John A.↗
NASA NTRS1985

Comparison of advanced turboprop installation on swept and unswept supercritical wings at transonic speeds

A series of wind-tunnel investigations were conducted to determine the aerodynamic interference associated with the over wing and under wing installation of a turboprop nacelle on 20 deg swept and unswept supercritical wings. The purpose of the investigations was to increase the understanding of the flow interactions involved with the nacelle turboprop integration and to obtain experimental data for the verification of computational prediction techniques. The models were tested in the Langley 16-Foot Transonic Tunnel at Mach numbers from 0.50 to 0.80 and at angles-of-attack from 0 to 5 deg. In addition, data at several propeller pitch angles and advance ratio settings were obtained. This paper which presents only the results of the over-the-wing nacelle installations shows that wing sweep had considerable influence on the installation interference. Large scale flow separation was observed on the swept wing at M = 0.8. Less severe effects were observed at M = 0.7 on the swept wing and for both M = 0.7 and 0.8 on the unswept wing.

Carlson, J. R.↗
NASA NTRS1987

Advanced turboprop wing installation effects measured by unsteady blade pressure and noise

A single rotation model propeller (SR-7A) was tested at simulated takeoff/approach conditions (Mach 0.2), in the NASA Lewis 9- by 15-Ft Anechoic Wind Tunnel. Both unsteady blade surface pressures and noise measurements were made for a tractor configuration with propeller/straight wing and propeller alone configurations. The angle between the wing chord and propeller axis (droop angle) was varied along with the wing angle of attack to determine the effects on noise and unsteady loading. A method was developed that uses unsteady blade pressure measurements to provide a quantitative indication of propeller inflow conditions, at least for a uniform (across the propeller disk) inflow angle. The wing installation caused a nearly uniform upwash at the propeller inlet as evidenced by the domination of the pressure spectra by the first shaft order. This inflow angle increased at a rate of almost 150 percent of that of the wing angle-of-attack for a propeller-wing spacing of 0.54 wing chords at a constant droop angle. The flyover noise, as measured by the maximum blade passing frequency level, correlates closely with the propeller inflow angle (approx. 0.6 dB per degree of inflow angle) for all droop angles and wing angles of attack tested, including the propeller alone data. Large changes in the unsteady pressure responses on the suction surface of the blade were observed as the advance ratio was varied. The presence of a leading edge vortex may explain this behavior since changes in the location of this vortex would change with loading (advance ratio).

Heidelberg, Laurence J.↗
NASA NTRS1987

Advanced turboprop wing installation effects measured by unsteady blade pressure and noise

A single rotation model propeller (SR-7A) was tested at simulated takeoff/approach conditions (Mach 0.2), in the NASA Lewis 9- by 15-Ft Anechoic Wind Tunnel. Both unsteady blade surface pressures and noise measurements were made for a tractor configuration with propeller/straight wing and propeller alone configurations. The angle between the wing chord and propeller axis (droop angle) was varied along with the wing angle of attack to determine the effects on noise and unsteady loading. A method was developed that uses unsteady blade pressure measurements to provide a quantitative indication of propeller inflow conditions, at least for a uniform (across the propeller disk) inflow angle. The wing installation caused a nearly uniform upwash at the propeller inlet as evidenced by the domination of the pressure spectra by the first shaft order. This inflow angle increased at a rate of almost 150 percent of that of the wing angle-of-attack for a propeller-wing spacing of 0.54 wing chords at a constant droop angle. The flyover noise, as measured by the maximum blade passing frequency level, correlates closely with the propeller inflow angle (approx. 0.6 dB per degree of inflow angle) for all droop angles and wing angles of attack tested, including the propeller alone data. Large changes in the unsteady pressure responses on the suction surface of the blade were observed as the advance ratio was varied. The presence of a leading edge vortex may explain this behavior since changes in the location of this vortex would change with loading (advance ratio).

Heidelberg, Laurence J.↗
NASA NTRS1994

Quiescent accretion disks in black hole X-ray novae

We present detailed time-resolved spectroscopy of the Balmer emission lines from two black hole binary systems in quiescence, A0620-00 and Nova Muscae 1991. We find extraordinary similarities between the two systems. There are 30-40 km/s velocity variations of the emission lines over the orbital period, the phases of which are not aligned with the expected phase of the motion of the compact primary. Detailed modeling of both systems is complicated by variable hot spot components, regions of optical thickness, and intermittent excess emission in the blue line wings of the H-alpha lines. Both sources also display low velocities at the outer edge of the accretion disk, implying a large primary Roche lobe and extreme mass ratios. These complications suggest that although simple optically thin, Keplerian alpha-disk models provide a useful parameterization of emission lines from these systems, the straightforward physical models they imply should be treated with great caution.

Orosz, Jerome A.↗
NASA NTRS1955

Aerodynamic Characteristics of a 0.04956-Scale Model of the Convair F-102A Airplane at Transonic Speeds

Tests have been conducted in the Langley 8-foot transonic tunnel on a 0.04956-scale model of the Convair F-102A airplane which employed an indented and extended fuselage, cambered wing leading edges, and deflected wing tips. Force and moment characteristics were obtained for Mach numbers from 0.60 to 1.135 at angles of attack up to 20 . In addition, tests were made over a limited angle-of-attack range to determine the effects of the cambered leading edges, deflected tips, and a nose section with a smooth area distribution. Fuselage modifications employed on the F-102A were responsible for a 25.percent reduction in the minimum drag-coefficient rise between the Mach numbers of 0.85 and 1.075 when compared with that for the earlier versions of the F-102. Although the wing modifications increased the F-102A subsonic minimum drag-coefficient level approximately 0.0020, they produced large decreases in drag at lifting conditions over that for the original (plane-wing) F-102. The F-102A had 15 to 25 percent higher maximum lift-drag ratios than did the original F-102. The F-102A had about 15 percent lower maximum lift-drag ratios at Mach numbers below 0.95 and slightly higher maximum lift-drag ratios at supersonic speeds when compared with those ratios for sn earlier modified-wing version of the F-102. Chordwise wing fences which provided suitable longitudinal stability for the original F-102 were not adequate for the cambered-wing F-102A The pitching-moment curves indicated a region of near neutral stability with possible pitch-up tendencies for the F-102A at high subsonic Mach numbers for lift coefficients between about 0.4 and 0.5.

Tempelmeyer, Kenneth E.↗
NASA NTRS2017

A Rigid Mid-Lift-to-Drag Ratio Approach to Human Mars Entry, Descent, and Landing

Current NASA Human Mars architectures require delivery of approximately 20 metric tons of cargo to the surface in a single landing. A proposed vehicle type for performing the entry, descent, and landing at Mars associated with this architecture is a rigid, enclosed, elongated lifting body shape that provides a higher lift-to-drag ratio (L/D) than a typical entry capsule, but lower than a typical winged entry vehicle (such as the Space Shuttle Orbiter). A rigid Mid-L/D shape has advantages for large mass Mars EDL, including loads management, range capability during entry, and human spaceflight heritage. Previous large mass Mars studies have focused more on symmetric and/or circular cross-section Mid-L/D shapes such as the ellipsled. More recent work has shown performance advantages for non-circular cross section shapes. This paper will describe efforts to design a rigid Mid-L/D entry vehicle for Mars which shows mass and performance improvements over previous Mid-L/D studies. The proposed concept, work to date and evolution, forward path, and suggested future strategy are described.

Cerimele, Christopher J.↗
NASA NTRSDate not supplied

Large-Drop Ice Accretion Test Results for a Large Scale Swept Wing Section

In-flight icing is an important consideration that affects aircraft design, performance and safety. Newer regulations combined with increasing demand to reduce fuel burn, emissions and noise are driving a need for improvements in icing simulation capability. To that end, this paper presents the results of ice accretion testing conducted in the NASA Icing Research Tunnel on a large swept wing typical of a modern commercial transport. The model was based upon a section of the Common Research Model wing at the 64% semispan station with a streamwise chord length of 136 in. The test conditions were developed with an icing scaling analysis to generate similar conditions for a small MVD = 25 μm and a large MVD = 110 μm. A series of tests were conducted over a range of total temperature from -23.8 ˚C to -1.4 ˚C with all other conditions held constant. The results for the small MVD cloud conditions were consistent with previous work and showed the changing ice morphology from rime ice at colder temperatures to highly 3D scallop ice in the range of -8.7 ˚C to -3.8 ˚C. The results for the large MVD cloud conditions exhibited some differences in the ice accretion morphology. Scallop-like ice features were observed at total temperature of -3.8˚C. The large MVD ice accretion at lower temperatures tended to be smoother than the corresponding ice accretion for small MVD. The thickness of the main ice shape tended to be larger for the small MVD conditions compared to the corresponding large MVD ice shape while the latter had more ice farther downstream. The measured ice mass was approximately equal between the corresponding small and large MVD ice shapes up to a freezing fraction of 0.6. For higher freezing fraction, the large MVD ice shapes weighed more. Cloud MVD variation from 50 μm to 230 μm while holding the scaling parameters constant resulted in very minor differences in the ice shapes, mostly in the upper and lower surface chordwise extents. Ice volume was computed from 3D scan data and used to calculate a ratio of ice mass to volume. The resulting values were in the range of 240 to 455 Kg/m3. While this is consistent with analogous values previously reported in the literature, more data are needed to determine a specific trend in this ratio as a function of freezing fraction and the corresponding governing physical phenomena. This work has resulted in a significant experimental database of ice accretion for small and large MVD conditions applicable to large-scale swept wings.

Icing↗