Ablative heat shields for Jupiter entry probes
Jupiter atmosphere entry probes graphite ablative heat shields performance, indicating convective and radiative blockage and graphite sublimation processes in surface heat balance
Lundell, J. H.↗
SEARCH · Search NASA
Results for “Wakefield”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Technology of planetary extreme environment simulation
Four test chamber systems were devleoped to simulate the extreme atmospheric environs of Venus and Jupiter, in order to assure satisfactory performance of scientific entry probes and their experiments.
Wakefield, M. E.↗
Space tug propulsion system failure mode, effects and criticality analysis
For purposes of the study, the propulsion system was considered as consisting of the following: (1) main engine system, (2) auxiliary propulsion system, (3) pneumatic system, (4) hydrogen feed, fill, drain and vent system, (5) oxygen feed, fill, drain and vent system, and (6) helium reentry purge system. Each component was critically examined to identify possible failure modes and the subsequent effect on mission success. Each space tug mission consists of three phases: launch to separation from shuttle, separation to redocking, and redocking to landing. The analysis considered the results of failure of a component during each phase of the mission. After the failure modes of each component were tabulated, those components whose failure would result in possible or certain loss of mission or inability to return the Tug to ground were identified as critical components and a criticality number determined for each. The criticality number of a component denotes the number of mission failures in one million missions due to the loss of that component. A total of 68 components were identified as critical with criticality numbers ranging from 1 to 2990.
Boyd, J. W.↗
A study of graphite ablation in combined convective and radiative heating.
Comparison of graphite ablation experiment results in the diffusion-controlled oxidation and sublimation regimes with results of an equilibrium chemistry, film coefficient ablation analysis. Mass transfer and energy transfer effects are considered. Tests were conducted in an arcjet facility at convective heating rates of 600 to 800 W/sq cm, radiative heating rates up to 2900 W/sq cm, with test specimen surface pressures of 0.06, 0.1, and 0.3 atm in an air stream. The experimental and analytical mass loss and surface temperature results agreed well when the carbon vapor thermodynamic properties from the JANAF tables are used in the analysis.
Wakefield, R. M.↗
Emittance of RSI Coatings Determined from Radiation Measurements in Arc Jet Tests
Simultaneous measurements were made on three surface insulation coatings for total surface radiation and radiation at discrete wavelengths between 0.88 and 4.5 microns. The mullite coating radiated all the applied heat at convective heat rates of 204 and 295 kw/sq m. Radiation from the ceramic mullite fiber coating was 170 kw/sq m at a heat rate of 454 kw/sq m. Effective total emissivity and spectral emissivity values were evaluated; all three coatings were significantly non-grey. Effective total emissivity values were 0.79 for mullite, 0.50 for ceramic mullite fiber, and 0.78 for silica composite.
Wakefield, R. M.↗
Explosive welding technique for joining aluminum and steel tubes
Silver sheet is wrapped around aluminum portion of joint. Mylar powder box is wrapped over silver sheet. Explosion welds silver to aluminum. Stainless-steel tube is placed over silver-aluminum interface. Mylar powder box, covered with Mylar tape, is wrapped around steel member. Explosion welds steel to silver-aluminum interface.
Wakefield, M. E.↗
Surface emissivity of a reinforced carbon composite material with an oxidation-inhibiting coating
Total effective emissivity and spectral emissivity over the wavelength range of 0.65 to 6.3 microns were determined for temperatures from 1300 t0 2250 deg K. A multi channel radiometer was used in the arcjet and laboratory tests. The black-body-hole method was used to independently check radiometer results. The results show the silicon-carbide coated reinforced carbon composite material is a nongray radiator. The total effective emissivity and the spectral emissivity at 0.65 micron both decreased with increasing temperature, respectively, from approximately 0.8 to 0.6, and from 0.4 to 0.25, over the temperature range. The emissivity values were the same when the sample was viewed normal to the surface or at a 45 deg angle. Recommended emissivity values are presented.
Wakefield, R. M.↗
Dissimilar metals joint evaluation
Dissimilar metals tubular joints between 2219-T851 aluminum alloy and 304L stainless steel were fabricated and tested to evaluate bonding processes. Joints were fabricated by four processes: (1) inertia (friction) weldings, where the metals are spun and forced together to create the weld; (2) explosive welding, where the metals are impacted together at high velocity; (3) co-extrusion, where the metals are extruded in contact at high temperature to promote diffusion; and (4) swaging, where residual stresses in the metals after a stretching operation maintain forced contact in mutual shear areas. Fifteen joints of each type were prepared and evaluated in a 6.35 cm (2.50 in.) O.D. size, with 0.32 cm (0.13 in.) wall thickness, and 7.6 cm (3.0 in) total length. The joints were tested to evaluate their ability to withstand pressure cycle, thermal cycle, galvanic corrosion and burst tests. Leakage tests and other non-destructive test techniques were used to evaluate the behavior of the joints, and the microstructure of the bond areas was analyzed.
Wakefield, M. E.↗
A description of a general use automated data reduction system
A data system developed for use in tests in arc jet facilities has the flexibility to accommodate various types of data, time resolution, and number of data signals. Data are tape-recorded, because a direct link to the IBM 360/67 computer is prohibited for safety reasons. The system is analogous to manual data reduction to promote user understanding and acceptance. Data computations may be performed in an interactive ('conversational') mode, for minimum delay in data reduction, or by card input. Reduced data are listed and also stored for plotting of further computational use. Operational costs of the system are reasonable, and both large and small data reduction tasks are handled readily.
Wakefield, R. M.↗
Yield-pressure determination
Stress/strain relationship of complex-shape vessel is recorded under hydrostatic pressure. Technique is used to test pressurized gas cylinders and tubular transition joints made of dissimilar metals and to determine burst or system-failure pressures.
Wakefield, M. E.↗
Low cost silicon solar arrays
The economic production of silicon solar cell arrays circumvents p-n junction degradation by nuclear doping, in which the Si-30 transmutes to P-31 after thermal neutron capture. Also considered are chemical purity specifications for improved silicon bulk states, surface induced states, and surface states.
Goldsmith, J. V.↗
Large area Czochralski silicon for solar cells
A detailed model of a typical Czochralski silicon crystal puller is utilized to predict maximum crystal growth rate as a function of various furnace parameters. Results of this analysis, when combined with multiblade slurry sawing, indicate that the Czochralski process is highly attractive for achieving near-term cost reduction of solar cell silicon.
Rea, S. N.↗
A method for determining structural properties of RCC thermal protection material
A method was developed for evaluation and prediction of effects of oxidation of the graphitic substrate on structural properties of Reinforced Carbon-Carbon (RCC) thermal protection material. Test specimens of RCC material were exposed to successive periods of convective heating in a plasma-jet facility to simulate the chemical reactions of Shuttle atmospheric entry. After each period of testing, the test specimen mass loss and performance in a nondestructive flexure test were determined. A computational model of the RCC specimen was developed for the NASA Structural Analysis (NASTRAN) program and validated by comparison of calculated and experimental results of flexure tests. The elastic moduli and ultimate loads in tension and compression were then computed for various levels of substrate oxidation.
Wakefield, R. M.↗
LSA silicon material task closed-cycle process development
The initial effort on feasibility of the closed cycle process was begun with the design of the two major items of untested equipment, the silicon tetrachloride by product converter and the rotary drum reactor for deposition of silicon from trichlorosilane. The design criteria of the initial laboratory equipment included consideration of the reaction chemistry, thermodynamics, and other technical factors. Design and construction of the laboratory equipment was completed. Preliminary silicon tetrachloride conversion experiments confirmed the expected high yield of trichlorosilane, up to 98 percent of theoretical conversion. A preliminary solar-grade polysilicon cost estimate, including capital costs considered extremely conservative, of $6.91/kg supports the potential of this approach to achieve the cost goal. The closed cycle process appears to have a very likely potential to achieve LSA goals.
Roques, R. A.↗
Protective Garment Ensemble
Protective garment ensemble with internally-mounted environmental- control unit contains its own air supply. Alternatively, a remote-environmental control unit or an air line is attached at the umbilical quick disconnect. Unit uses liquid air that is vaporized to provide both breathing air and cooling. Totally enclosed garment protects against toxic substances.
Wakefield, M. E.↗
Study of fuel cell on-site, integrated energy systems in residential/commercial applications
Three building applications were selected for a detailed study: a low rise apartment building; a retail store, and a hospital. Building design data were then specified for each application, based on the design and construction of typical, actual buildings. Finally, a computerized building loads analysis program was used to estimate hourly end use load profiles for each building. Conventional and fuel cell based energy systems were designed and simulated for each building in each location. Based on the results of a computer simulation of each energy system, levelized annual costs and annual energy consumptions were calculated for all systems.
Wakefield, R. A.↗
Surface flaw detection in structural ceramics by scanning photoacoustic spectroscopy
Laser-scanned photoacoustic spectroscopy has been used to detect tightly closed surface cracks in three structural ceramic materials: sintered silicon nitride, reaction-bonded silicon nitride, and sintered silicon carbide. It is found that the amplitude of the photoacoustic signal from the flaws is greater for the silicon nitrides than for silicon carbide, which is attributed to the lower thermal diffusivity of silicon nitride as well as differences in the grain size distribution and chemical composition. Signal amplitude, reproducibility, and signal-to-noise ratio are acceptable for effective flaw detection
Khandelwal, P. K.↗
Performance of entry heat shields on Pioneer Venus probes
The Pioneer Venus probes approached Venus with high relative velocity. As they entered the atmosphere, they were rapidly decelerated by aerodynamic drag, and a great deal of heat was generated. To protect the probe structure and the scientific instruments, a carbon phenolic heat shield was placed on the front of the probes. Because the design of heat shields for planetary entry is a developing technology, thermocouples were placed in the heat shields so that actual and predicted heat shield performance could be compared. The function of the heat shield is discussed, the probe environments during entry into the Venusian atmosphere are described, and some results from the heat shield experiment are presented. It was found that for the most part, the heat shields performed better than expected.
Pitts, W. C.↗