SEARCH · Search NASA

Results for “Water Cut”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

DOE OSTI2020

Performance of Low Salinity Polymer Flood in Enhancing Heavy Oil Recovery on the Alaska North Slope

Combining low-salinity water (LSW) and polymer flooding was proposed to unlock the tremendous heavy oil resources (20–25 billion barrels) on the Alaska North Slope (ANS). The synergy effect of LSW and polymer flooding was demonstrated through coreflooding experiments carried out on representative rock and fluid systems. The results indicate that the high-salinity polymer solution (HSP, 2,300 ppm, salinity=27,500 ppm) requires nearly two thirds more polymer than the low-salinity polymer (LSP, 1,400 ppm, salinity=2,500 ppm) to achieve the same target viscosity of 45 cp measured from viscometer. Additional oil (5–9%) can be recovered from LSW flooding after extensive high-salinity water (HSW) flooding. LSW flooding performed in secondary mode can achieve higher recovery than in tertiary mode. Strikingly, LSP flooding can further improve the oil recovery by ~8% even after extensive HSP flooding with the same viscosity. LSP flooding performed directly after waterflooding can achieve ~10% more incremental oil recovery. The pH increase of the effluent during LSW/LSP flooding was significantly greater than that during HSW/HSP flooding, indicating the occurrence of ion exchange which might contribute to the improved oil recovery. Also, the water breakthrough was delayed in a low-salinity flood compared with a high-salinity flood. The idea of combining LSW and polymer flooding has been put into practice on a pattern-scale field pilot test in the target Milne Point field. Nearly two-year observation has shown impressive success: water cut reduction (70% to below 15%), increasing oil rate, and no polymer breakthrough so far. This work has demonstrated remarkable economical and technical benefits of combination of LSW and polymer flooding in enhancing heavy oil recovery.

Zhao, Yang↗

DOE OSTI2020

Enhancing Heavy-Oil-Recovery Efficiency by Combining Low-Salinity-Water and Polymer Flooding

Summary Combining low-salinity-water (LSW) and polymer flooding was proposed to unlock the tremendous heavy-oil resources on the Alaska North Slope (ANS). The synergy of LSW and polymer flooding was demonstrated through coreflooding experiments at various conditions. The results indicate that the high-salinity polymer (HSP) (salinity = 27,500 ppm) requires nearly two-thirds more polymer than the low-salinity polymer (LSP) (salinity = 2,500 ppm) to achieve the target viscosity at the condition of this study. Additional oil was recovered from LSW flooding after extensive high-salinity-water (HSW) flooding [3 to 9% of original oil in place (OOIP)]. LSW flooding performed in secondary mode achieved higher recovery than that in tertiary mode. Also, the occurrence of water breakthrough can be delayed in the LSW flooding compared with the HSW flooding. Strikingly, after extensive LSW flooding and HSP flooding, incremental oil recovery (approximately 8% of OOIP) was still achieved by LSP flooding with the same viscosity as the HSP. The pH increase of the effluent during LSW/LSP flooding was significantly greater than that during HSW/HSP flooding, indicating the presence of the low-salinity effect (LSE). The residual-oil-saturation (Sor) reduction induced by the LSE in the area unswept during the LSW flooding (mainly smaller pores) would contribute to the increased oil recovery. LSP flooding performed directly after waterflooding recovered more incremental oil (approximately 10% of OOIP) compared with HSP flooding performed in the same scheme. Apart from the improved sweep efficiency by polymer, the low-salinity-induced Sor reduction also would contribute to the increased oil recovery by the LSP. A nearly 2-year pilot test in the Milne Point Field on the ANS has shown impressive success of the proposed hybrid enhanced-oil-recovery (EOR) process: water-cut reduction (70 to less than 15%), increasing oil rate, and no polymer breakthrough so far. This work has demonstrated the remarkable economical and technical benefits of combining LSW and polymer flooding in enhancing heavy-oil recovery.

Engineering↗

DOE OSTI2024

Advanced Characterization to Inform Sustainable Recovery of Critical Minerals from Fossil Energy Waste Feedstocks

Rare earth elements (REE) and other critical minerals (CM, e.g., Co, Li) have important uses in green energy and modern technologies, yet are vulnerable to potential supply chain disruptions. One potential domestic source of CM is fossil energy wastes, such as acid mine drainage (AMD) and treatment solids (AMD solids), coal combustion ash, and Oil and Gas (O&G) drilling wastes (drill cuttings and produced waters). CM recovery from these waste feedstocks is promising due to their abundances and fast availability as waste products. On the other hand, the CM occurrence in these wastes is in small quantities compared to traditional ore bodies. Thus, novel and strategic separation and extraction processes are under exploration. Researchers at DOE’s National Energy Technology Laboratory (NETL) are collecting and analyzing CM data for aforementioned fossil energy wastes, and utilizing advanced geochemical characterization (e.g., synchrotron microprobe and sequential extraction) to understand the CM speciation and binding environments in these materials to better inform sustainable and effective recovery. Successful examples discussed in this talk include: (1) the discovery of easily mobile REE phases in Ca-rich coal combustion ash and developing a patented REE recovery process from Ca-rich Powder River Basin coal ash; (2) the successful identification of REE/Co/Ni/Zn hosting phases in acid mine drainage treatment solids (AMD solids) with diverse chemical composition (Al, Mn, or Fe-rich) informing the sequential recovery of different REE/CMs from AMD solids; (3) the recovery potential of Li and other CMs in O&G produced waters and drill cuttings. The innovations driven by characterization have the potential to offset the cost of waste management and wastewater treatments while reducing the cost and environmental footprint of CM extraction.

characterization and extraction↗

DOE OSTI2024

Characterization Inform Sustainable Recovery of Critical Minerals from Fossil Energy Waste Feedstocks

Rare earth elements (REE) and other critical minerals (CM, e.g., Co, Ni, Li) have important uses in green energy and modern technologies, yet are vulnerable to potential supply chain disruptions. One potential domestic CM source is fossil energy wastes, such as acid mine drainage (AMD) and treatment solids (AMD solids), coal combustion ash, and Oil and Gas (O&G) drilling wastes (drill cuttings and produced waters). While they can contain lower CM concentrations then traditional ore, the quantity and fast availability as waste feedstock makes them a promising CM resource. To explore their promise, researchers at DOE’s National Energy Technology Laboratory (NETL) have collected and analyzed CM data for aforementioned fossil energy wastes, and utilized advanced geochemical characterization (e.g., synchrotron microprobe and sequential extraction) to identify the CM speciation and binding environments, and developed sustainable and targeted CM recovery. Successful examples include: (1) the discovery of easily mobile REE phases in Ca-rich coal combustion ash and developing a patented REE recovery process from Ca-rich Powder River Basin coal ash; (2) the successful identification of REE/Co/Ni/Zn hosting phases in acid mine drainage treatment solids (AMD solids) with diverse chemical composition (Al, Mn, or Fe-rich) informing the sequential recovery of different REE/CMs from AMD solids; (3) the recovery potential of Li and other CMs in O&G produced waters and drill cuttings. The innovations driven by characterization have the potential to offset the cost of waste management and wastewater treatments while reducing the cost and environmental footprint of CM extraction.

Stuckman, Mengling↗

DOE OSTI2025

Informed Critical Mineral Recovery from Fossil Energy Waste Feedstocks

Critical minerals (CM), such as rare earth elements (REE), cobalt, nickel, and lithium, have important uses in modern energy and technologies, yet are vulnerable to potential supply chain disruptions. One potential domestic CM source is fossil energy wastes, such as coal combustion ash, acid mine drainage (AMD) and treatment solids (AMD solids), and Oil and Gas (O&G) drilling wastes (drill cuttings and produced waters). CM recovery from these feedstocks is promising due to their abundant quantity and fast availability as waste products. To develop informed and effective CM recovery, DOE’s National Energy Technology Laboratory (NETL) have collected and analyzed CM data for aforementioned fossil energy wastes, and utilized advanced geochemical characterization (e.g., synchrotron microprobe, sequential extraction and geochemical modeling) to identify the CM speciation and binding environments. Novel methods that recover multiple CMs while co-producing other valuable byproducts from these feedstocks have been developed. Successful examples include: (1) the discovery of easily mobile REE phases in Ca-rich coal combustion ash resulted in a patented REE recovery process from the ash feedstock while producing zeolite sorbents from the extraction wastes; (2) the successful identification of REE/Co/Ni/Zn hosting phases in acid mine drainage treatment solids (AMD solids) has informed the sequential CM recovery from AMD solids and has inspired lithium sorbent development from the extraction wastes; (3) the recovery potential of Li and other CMs in O&G produced waters and drill cuttings has been explored while the extraction residuals have been demonstrated to support plant growth as soil supplements. The innovations driven by characterization information have the potential to maximize CM recovery revenue, offset the cost of waste management and wastewater treatments while reducing the cost and environmental footprint of CM extraction.

characterization and extraction of rare earth elem↗

DOE OSTI2020

Stingray Case Study

Improvised explosive devices (IEDs) have injured and killed numerous soldiers and civilians as a consequence of military operations in the Middle East. With gaps in existing technologies, the US military required devices for quickly addressing deadly IEDs without harming military personnel or inflicting severe damage to the environment. In response to this need, Sandia developed Stingray, a clear, plastic handheld device to quickly and safely disable threatening IEDs. Stingray is designed to be used in two configurations: a coherent water blade for cutting operations and as a water slug for general device disruption. Prior to disabling an IED, Explosive Ordnance Disposal (EOD) technicians will x-ray the target using tools such as Sandia's X-ray Toolkit (XTK) to determine which function operators should use to dismantle the IED. For example, if the operator knows exactly which wires to cut, they can use the precision water blade. If the operator wants to create a general disruption, they can use the water slug function.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

DOE OSTI2021

Evaluation of Potential Impacts of Free Chlorine during Washing of Fresh-Cut Leafy Greens on Escherichia coli O157:H7 Cross-Contamination and Risk of Illness

Addition of chlorine-based antimicrobial substances to fresh-cut leafy green wash water is done to minimize microbial cross-contamination during processing. We developed the FDA Leafy Green Risk Assessment Model (FDA-LGRAM) to quantify the impact of free chlorine concentration in wash water during fresh-cut lettuce processing on the extent of water-mediated cross-contamination between shredded lettuce and the associated risk of illness due to exposure to Escherichia coli O157:H7. At different contamination prevalence and levels of E. coli O157:H7 on incoming lettuce heads, the model compared the predicted prevalence of contaminated fresh-cut lettuce packages and the risk of illness per serving between: (1) a scenario where fresh-cut lettuce was packaged without washing; and (2) scenarios involving washing fresh-cut lettuce with different levels of free chlorine (0 ppm, 5 ppm, 10 ppm, 15 ppm, and 20 ppm) prior to packaging. Our results indicate that the free chlorine level in wash water has a substantial impact on the predicted prevalence of contaminated fresh-cut lettuce packages and the risk of illness associated with E. coli O157:H7 in fresh-cut lettuce. Results showed that the required level of free chlorine that can minimize water-mediated cross-contamination and reduce the corresponding risk of illness depended on contamination prevalence and levels of E. coli O157:H7 on incoming lettuce heads. Our model also indicated that the pathogen inactivation rate in wash water via free chlorine was a key model parameter that had a significant impact on the extent of cross-contamination during washing and the predicted associated risk of illness.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2022

Flow Loop Study of ECT-Based Volume Fraction Monitoring in Oil–Water Two-Phase Flows

Measurement of phase volume fractions in water-containing multiphase flows is necessary for the optimization of a host of industrial flow processes. Many water-containing multiphase flows can be classified as either water-dispersed or water-continuous mixtures. A recently developed approach based on Hanai’s mixture formula and utilizing electrical capacitance tomography (ECT) sensors have shown good potential for obtaining water volume fraction estimates in two-phase water-containing flows with different water salinity levels. However, the proposed approach was investigated via controlled experiments restricted to static configurations while, in practice, multiphase flows can be dynamic and unpredictable. In this work, we perform a flow loop study of the proposed ECT-based method for volume fraction estimation in oil–water two-phase flows. Here, we evaluate the performance of the proposed method in both water-dispersed and water-continuous flow regimes by employing different types of capacitive sensors in cylindrical arrangements and parallel-plate rectangular arrangements.

02 PETROLEUM↗

DOE OSTI2021

Raw leaf gas exchange data, Leaf traits and 13CO2 experiment in the Amazon basin, Manaus, Brazil, 2019

This data package contains raw light response curves of mature leaves from 26 individuals, distributed among 18 species with different canopy positions, and leaf traits (LMA, N, P, and NSC) from Manaus-Brazil (June-November 2019). Branches were cut from the tree and re-cut under water. All measurements were made using (Li-6400XT, Li-Cor®, Lincoln, USA) under standard environmental conditions. Also, have data from an experiment with 13CO2 using a combined method with Licor 6400XT and Picarro. The experiment was conducted with one tropical species and measured the concentration of ¹³CO2 and ¹²CO2 to estimate rates of leaf respiration. All the files included in this data package are in .csv format with additional metadata spreadsheets in Excel file formats.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2022

Leaf gas exchange (BNL-PNNL collaboration), San Lorenzo, Panama, 2020

This data package contains Photosynthetic CO2 response (ACi curves) and Light Response (AQ) of mature sunlit canopy leaves of 11 species from PA-SLZ, February 2020. Branches were cut from the top of the canopy and re-cut under water. Fitted Vcmax and Jmax photosynthetic parameters were derived from measured data as well as the convexity, light use efficiency and apparent quantum yield. This data was collected as a collaboration between Brookhaven National Laboratory (BNL) and Pacific Northwest National Laboratory (PNNL), and is a subset of the 2020 BNL Panama campaign. The species included in this dataset are: Apeiba membranacea, Carapa guianensis, Cespedesia spathulate, Jacaranda copaia, Lonchocarpus heptaphyllus, Pera arboea, Pourouma bicolore, Symphonia globulifera, Tachigali versicolor, Tapirira guianensis, and Virola sebifera. The files included in this data package are in .csv and .pdf format, with two Excel files containing additional metadata.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2024

Advanced Multi-Dimensional Capacitance Sensors Based Subsea Multiphase Mass Flow Meter to Measure and Monitor Offshore Enhanced Oil

This innovation is based on advanced multi-dimensional extensions of ECVT sensors that involve ECVT, Displacement Current Phase Tomography (DCPT), Maxwell-Wagner-Sillars polarization effect (MWS), and velocimetry which exploit the variation of electric properties between the oil, water, and gas coming out of the well. Capacitance sensors are embedded on the inside of a pipe spool and placed in-line with the subsea oil line piping on the extraction end of the well. The difference in dielectric, dielectric loss, surface polarization, and velocity of each phase are used in the multi-dimensional algorithm to measure the volume fraction, distribution, velocity, mass flow rate, and flow regime of the mixture moving through the pipe.

02 PETROLEUM↗

DOE OSTI2025

Producing Dollars from Produced Water: How we Get There and Why we Should

Recent studies have shown that produced water and drill cuttings from the development of unconventional shale in Appalachia has a significant source of valuable critical minerals, including lithium, putting Pennsylvania in a unique position to capitalize. This session presents how we capitalize on this opportunity to produce dollars from produced water, the opportunities, and the challenges.

critical minerals, lithium, rare earth elements↗

DOE OSTI2025

"Mining" for Critical Minerals: Critical Minerals from Fossil Energy Waste Byproducts

NETL researcher Mengling Stuckman is an invited speaker for the panel discussion session of "Mining for Critical Minerals" at the Marcellus Shale Coalition event, "Shale 2.0: Learn the Facts about Upstream, Midstream and Downstream". Recent studies from DOE have shown that produced water and drill cuttings from the development of unconventional shale in Appalachia has a significant source of valuable critical minerals and will support bolstering America's supply chain security, putting Pennsylvania in a unique position to capitalize. The panel discussion facilitates obtaining an overview of pipeline capacity needs, downstream users for natural gas and effectively educating and engaging the public relevant to the Marcellus Shale community. The event also offers opportunities for local oil and gas industries, water and waste management companies to work with NETL and participate in FECM’s Critical Mineral program. Industrial feedbacks and participation as outcomes of this invited talk will accelerate the technology and knowledge transfer for the DOE’s Critical Mineral program and for DOE’s mission to unleash American Energy and lead in energy innovation.

critical minerals↗

DOE OSTI2026

Innovations Driven by Advanced Characterization to Strategize Critical Mineral Production and Beneficial Reuse from Fossil Energy Waste

Critical minerals (CM), such as rare earth elements (REE), cobalt, nickel, and lithium, have important uses in modern electronics and advanced manufacturing, yet are vulnerable to potential supply chain disruptions. Relatively abundant and readily available fossil energy (FE) wastes, such as coal combustion ash, acid mine drainage (AMD) and treatment solids (AMD solids), and Oil and Gas (O&G) drilling wastes (drill cuttings and produced waters) are under consideration as CM feedstocks. The National Energy Technology Laboratory (NETL) has studied CM resources for various FE wastes as part of the U.S. Department of Energy’s mission of bolstering the domestic CM supply, and makes the data available to the public on EDX at sites such as the NEWTS group. Advanced characterization utilizing synchrotron x-ray techniques coupled with laboratory extractions has been performed to identify CM hosting phases in these FE wastes to inform CM recoverability mechanisms. Novel methods to selectively recover CMs while co-producing other valuable byproducts have been developed. Successful examples discussed here include: (1) The identification of REE/Co/Ni/Sc binding and hosting phases in select FE waste (coal combustion ash and AMD solids), resulting in the development of a patented CM step-extraction process, (2) coupled production of functional sorbents from these extraction wastes and for CM recovery. A pilot-scale testing to evaluate the patent’s technical feasibility for extracting REE from coal ash on a barrel scale has been successfully performed. Additionally, (3) evaluation and measurements of brine geochemistry from U.S. O&G produced waters has informed a high Li recovery potential from Marcellus Shale produced water. NETL researchers have been developing tailored pre-treatment processes, an innovative and highly durable lithium sorbent, and geochemical model guided precipitation to accelerate Li production from the Marcellus Shale produced waters. These innovations driven by characterization are integral for maximizing and advancing the potential for CM recovery while offsetting the cost and environmental footprint for FE waste management.

critical mineral processing↗

DOE OSTI2024

Liquid Abrasive Cutter Power Generation Unit Requirements

This document details the requirements for the purchase of a power generating unit (PGU) for an updated Liquid Abrasive Cutter (LAC) for use in field conditions. The system will provide high pressure water and will be integrated with existing waterjet cutting attachments to cut various materials. The system will be standalone, requiring only water, and electrical energy. Cutting heads, attachments, and a garnet delivery system are not included in this specification. This system is an evolution of the existing LAC (developed at LLNL). The PGU specified herein will have the ability to operate on electrical power via an electric motor, and accept input power from a variety of sources, such as an engine-driven generator, battery pack, solar, shore power, or micro-grid.

42 ENGINEERING↗

DOE OSTI2023

Experimental results of embedded phase change material capsules for increasing the performance of a wrapped heat pump water heater

Herein, to enhance the capacity of heat pump water heaters (HPWHs), high energy density phase change material (PCM) was used in two experimentally tested HPWH prototypes. Preliminary findings showed that in the PCM, stored thermal potential energy could be effectively converted into sensible heat in the water over a slight temperature difference, with the goal of increasing the capacity of hot water above a desired cut-off temperature. This exchange of energy results in an increased amount of hot water necessary for mixing at the location utilized by the consumer. It was also found that for a wrapped HPWH, there was an average increase of 27.7% in the capacity when 7.6 L of novel PCM filled spherical capsules were added to a 22.7 L tank downstream of the HPWH. In the second design (Beta), PCM capsules were immersed into the tank with a cylindrical geometry, and the UEF was increased by 5.5% over the baseline HPWH test result. As for the Beta design, heat loss was reduced significantly compared to a typical HPWH and the Alpha design. Food-grade PCMs were selected as appropriate. The novel encapsulation design increased the effective conductivity inside the capsule by adding metal fins.

42 ENGINEERING↗

DOE OSTI2024

Water-induced surface ordering facilitating the microcutting of ductile metals

Metal cutting is a crucial process in modern manufacturing. Enhancing the machinability of metals can significantly improve their production efficiency and surface integrity. Coating surface-active media (SAM) on the free surface of the metals before cutting is an easy method to improve machinability, which usually pertains to the category of the renowned Rehbinder effect. However, the existing SAM is usually hazardous and complex materials. Besides, the effect of SAM on the local structure of the metal surface remains unclear. In this study, water is employed as a simple yet often overlooked SAM in the microcutting of copper. Using water as SAM also allows the employment of X-ray absorption fine structure spectroscopy (XAFS) to study the local structure of copper with and without water coating. Results show that water coating on the free surface of copper can significantly reduce the cutting force and chip thickness, and improve the surface finish. Interestingly, removing the water coating enables the recovery of the cutting force, demonstrating a reversible effect. Based on the XAFS results and molecular dynamics simulation, a water-induced surface ordering mechanism is proposed to explain the findings from the microcutting experiments. This mechanism suggests that water molecules can induce surface ordering in copper, resulting in reduced surface energy and fracture toughness of copper, thus enhancing machinability. In conclusion, this work provides valuable insights into the comprehension of the Rehbinder effect and shows that picometer-scale modifications of the surface atom arrangement can considerably alter the deformation mode of metals, paving the way for the development of new manufacturing processes.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Hydrothermal corrosion behavior of CVD SiC in high temperature water

Here, the hydrothermal corrosion of polished and as-cut high purity chemical vapor deposited (CVD) SiC was studied in a constantly refreshing water loop. Light water reactor (LWR) conditions were simulated at 288, 320, and 350 °C with dissolved gas concentrations between 0.15 and 3 ppm H 2 or between 1 and 4 ppm O 2 . In hydrogenated water, the rate of material loss was low, calculated to be ~1.3 μm of recession after 5 years of service in 320 °C water. Moreover, there was no observed localized attack at any temperature. In oxygenated conditions, the corrosion rate was higher, with a calculated material loss >10 μm after 5 years of service in 1 ppm O 2 , 320 °C water. Mass loss significantly increased when grain fallout became significant (as early as 200h with 4 ppm O 2 at 350 °C or after 1000–2000h with 2 ppm O 2 at 288 °C). Grain fallout more than doubled the corrosion rate and a steady state corrosion rate in the grain fallout regime was not observed but expected to eventually occur once large grains begin to be removed. Polished specimens had lower mass loss than unpolished coupons. A kinetic analysis of the data in this work suggests that the corrosion rates are controlled by a single activation step in both oxygenated and deoxygenated conditions, with the reaction order with respect to oxygen being 1. A resulting reaction rate equation to predict corrosion of SiC (in mg/cm 2 s) in high purity water from 288 to 350 °C and up to 4 ppm O 2 was constructed: Rate = $\frac{0.1458}{1+SA}$ T (1.09(1–10 -3 T)[O 2 ]e– $\frac{1.275x10^4}{T}$ + 7.91x10 -6 e– $\frac{7.39x10^3}{T}$).

36 MATERIALS SCIENCE↗