Search NASA⌕ Search

SEARCH · Search NASA

Results for “Weight Lifting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

A 2 Tesla Full Scale High Performance Periodic Permanent Magnet Model for Attractive (228 KN) and repulsive Maglev

Two 214.5 cm. long high performance periodic (26 cm period) permanent magnet half-assemblies were designed and constructed for use as a wiggler using Nd-B-Fe and vanadium permendur as hard and soft magnetic materials by Field Effects, a division of Intermagnetics General Corporation. Placing these assemblies in a supporting structure with a 2.1 cm pole to pole separation resulted in a periodic field with a maximum value of 2.04 T. This is believed to be the highest field ever achieved by this type of device. The attractive force between the two 602 kg magnet assemblies is 228 kN, providing enough force for suspension of a 45,500 kg vehicle. If used in an attractive maglev system with an appropriate flat iron rail, one assembly will generate the same force with a gap of 1.05 cm leading to a lift to weight ratio of 38.6, not including the vehicle attachment structure. This permanent magnet compares well with superconducting systems which have lift to weight ratios in the range of 5 to 10. This paper describes the magnet assemblies and their measured magnetic performance. The measured magnetic field and resulting attractive magnetic force have a negative spring characteristic. Appropriate control coils are necessary to provide stable operation. The estimated performance of the assemblies in a stable repulsive mode, with eddy currents in a conducting guideway, is also discussed.

Stekly, Z. J. J.↗
NASA NTRS1992

Electrically Controlled Valve With Small Motor

Design of electrically controlled valve exploits force-multiplying principle to overcome large back-pressure force resisting initial opening. Design makes possible to open valve by use of relatively small motor adequate for rest of valve motion, but otherwise not large enough to open valve. In simple linear lifting, small horizontal forces applied to pair of taut cables to lift large weight through short distance. In rotary lifting, similar effect achieved by rotating, about an axis, disk to which initially axial cables attached.

Reinicke, Robert H.↗
NASA NTRS1984

Controlled ecological life support systems for space habitats

The development of regenerative life support systems to meet the physiological requirements of humans in space is described. A review of previous research on regenerative systems is presented. NASA's Controlled Ecological Life Support System (CELSS) program, which is to develop an environment for a human space crew, is discussed. The table of physiological requirements of an average human and the logical system approach to planning a closed system created by Spurlock and Modell (1976, 1978) are examined. The weight of food and oxygen with respect to lift-off weight is investigated. The creation of the proper atmosphere for space, by balancing all the necessary parameters is studied. The need for a mineral and fluid balance and methods of maintaining it are analyzed. The required cooperation between physicians, physiologists, and nutritionists for the success of the CELSS program is discussed.

Buchanan, P.↗
NASA NTRS1976

Development of weight and cost estimates for lifting surfaces with active controls

Equations and methodology were developed for estimating the weight and cost incrementals due to active controls added to the wing and horizontal tail of a subsonic transport airplane. The methods are sufficiently generalized to be suitable for preliminary design. Supporting methodology and input specifications for the weight and cost equations are provided. The weight and cost equations are structured to be flexible in terms of the active control technology (ACT) flight control system specification. In order to present a self-contained package, methodology is also presented for generating ACT flight control system characteristics for the weight and cost equations. Use of the methodology is illustrated.

Anderson, R. D.↗
NASA NTRS1998

Launch Vehicle Performance with Solid Particle Feed Systems for Atomic Propellants

An analysis of launch vehicle Gross Liftoff Weight (GLOW) using high energy density atomic propellants with solid particle feed systems was conducted. The analyses covered several propellant combinations, including atoms of aluminum (Al), boron (B). carbon (C), and hydrogen (H) stored in a solid cryogenic particle, with a cryogenic liquid as the carrier fluid. Several different weight percents (wt%) for the liquid carrier were investigated and the gross lift off weight (GLOW) of the vehicles using the solid particle feed systems were compared with a conventional 02/H2 propellant vehicle. The potential benefits and effects of feed systems using solid particles in a liquid cryogenic fluid are discussed.

Palaszewski, Bryan↗
NASA NTRS1998

Recombination Catalysts for Hypersonic Fuels

The goal of commercially-viable access to space will require technologies that reduce propulsion system weight and complexity, while extracting maximum energy from the products of combustion. This work is directed toward developing effective nozzle recombination catalysts for the supersonic and hypersonic aeropropulsion engines used to provide such access to space. Effective nozzle recombination will significantly reduce rk=le length (hence, propulsion system weight) and reduce fuel requirements, further decreasing the vehicle's gross lift-off weight. Two such catalysts have been identified in this work, barium and antimony compounds, by developing chemical kinetic reaction mechanisms for these materials and determining the engine performance enhancement for a typical flight trajectory. Significant performance improvements are indicated, using only 2% (mole or mass) of these compounds in the combustor product gas.

Chinitz, W.↗
NASA NTRS1977

An elementary analysis of the effect of sweep, Mach number, and lift coefficient on wing-structure weight

Results are presented from an elementary analysis of the effect of sweep angle on the idealized structural weight of swept wings, with cruise Mach number M and lift coefficient C sub L as parameters. The analysis indicates that sweep is unnecessary for cruise Mach numbers below about 0.80, whereas for the higher subsonic speeds, a well defined minimum-weight condition exists at a sweep angle in the neighborhood of 35 deg or 40 deg, depending on M and C sub L. The results further indicate that wing-structure weight increases sharply with Mach number in the high subsonic range, with Mach 0.85 wings weighing half again as much as Mach 0.75 wings. Weight is also shown to increase with cruise lift coefficient, but the effect is not strong for the usual range of design lift coefficients. Minimum wing-structure weight is found to occur at a ratio of thickness to normal chord of about 18 percent, but it is concluded that the thickness ratio for optimum wing design would probably lie in the range of 12 to 15 percent.

Kyser, A. C.↗
NASA NTRS1975

Flight test of a spin parachute for use with a Super Arcas sounding rocket

The development and flight testing of a specially configured 16.6 ft Disc Band Gap (DBG) Spin Parachute is discussed. The parachute is integrated with a modified Super Arcas launch vehicle. Total payload weight was 17.6 lbs including the Spin Parachute and a scientific payload, and lift-off weight was 100.3 lbs. The Super Arcas vehicle was despun from 18.4 cps. After payload separation at 244,170 ft the Spin Parachute and its payload attained a maximum spin rate of 2.4 cps. Total suspended weight of the Spin Parachute and its payload was 14.64 lbs.

Silbert, M. N.↗
NASA NTRS1990

Design synthesis and optimization of joined-wing transports

A computer program for aircraft synthesis using a numerical optimizer was developed to study the application of the joined-wing configuration to transport aircraft. The structural design algorithm included the effects of secondary bending moments to investigate the possibility of tail buckling and to design joined wings resistant to buckling. The structural weight computed using this method was combined with a statistically-based method to obtain realistic estimates of total lifting surface weight and aircraft empty weight. A variety of 'optimum' joined-wing and conventional aircraft designs were compared on the basis of direct operating cost, gross weight, and cruise drag. The most promising joined-wing designs were found to have a joint location at about 70 percent of the wing semispan. The optimum joined-wing transport is shown to save 1.7 percent in direct operating cost and 11 percent in drag for a 2000 nautical mile transport mission.

Gallman, John W.↗
NASA NTRS1974

A method for determining optimum phasing of a multiphase propulsion system for a single-stage vehicle with linearized inert weight

A general analytical treatment is presented of a single-stage vehicle with multiple propulsion phases. A closed-form solution for the cost and for the performance and a derivation of the optimal phasing of the propulsion are included. Linearized variations in the inert weight elements are included, and the function to be minimized can be selected. The derivation of optimal phasing results in a set of nonlinear algebraic equations for optimal fuel volumes, for which a solution method is outlined. Three specific example cases are analyzed: minimum gross lift-off weight, minimum inert weight, and a minimized general function for a two-phase vehicle. The results for the two-phase vehicle are applied to the dual-fuel rocket. Comparisons with single-fuel vehicles indicate that dual-fuel vehicles can have lower inert weight either by development of a dual-fuel engine or by parallel burning of separate engines from lift-off.

Martin, J. A.↗
NASA NTRS1972

Upper-stage space shuttle propulsion by means of separate scramjet and rocket engines

A preliminary mission study of a reusable vehicle from staging to orbit indicates payload advantages for a dual-propulsion system consisting of separate scramjet and rocket engines. In the analysis the scramjet operated continuously and the initiation of rocket operation was varied. For a stage weight of 500,000 lb the payload was 10.4 percent of stage weight or 70 percent greater than that of a comparable all-rocket-powered stage. When compared with a reusable two-state rocket vehicle having 50,000 lb payload, the use of the dual propulsion system for the second stage resulted in significant decreases in lift-off weight and empty weight, indicating possible lower hardware costs.

Franciscus, L. C.↗
NASA NTRS1978

Earth-to-orbit reusable launch vehicles: A comparative assessment

A representative set of space systems, functions, and missions for NASA and DoD from which launch vehicle requirements and characteristics was established as well as a set of air-breathing launch vehicles based on graduated technology capabilities corresponding to increasingly higher staging Mach numbers. The utility of the air-breathing launch vehicle candidates based on lift-off weight, performance, technology needs, and risk was assessed and costs were compared to alternative concepts. The results indicate that a fully reusable launch vehicle, whether two stage or one stage, could potentially reduce the cost per flight 60-80% compared to that for a partially reusable vehicle but would require advances in thermal protection system technology. A two-stage-to-orbit, parallel-lift vehicle with an air-breathing booster would cost approximately the same as a single-stage-to-orbit vehicle, but the former would have greater flexibility and a significantly reduced developmental risk. A twin-booster, subsonic-staged, parallel-lift vehicle represents the lowest system cost and developmental risk. However, if a large supersonic turbojet engine in the 350,000-N thrust class were available, supersonic staging would be preferred, and the investment in development would be returned in reduced program cost.

Chase, R. L.↗
NASA NTRS1961

Orbital Payload Reductions Resulting from Booster and Trajectory Modifications for Recovery of a Large Rocket Booster

An analysis was made to determine the reduction in payload for a 300 nautical mile orbit resulting from the addition of inert weight, representing recovery gear, to the first-stage booster of a three-stage rocket vehicle. The values of added inert weight investigated ranged from 0 to 18 percent of gross weight at lift off. The study also included the effects on the payload in orbit and the distance from the launch site at burnout and at impact caused by variation in the vertical rise time before the programmed tilt. The vertical rise times investigated ranged from 16-7 to 100 percent of booster burning time. For a vertical rise of 16.7 percent of booster burning time it was found that a 50-percent increase in the weight of the empty booster resulted in only a 10-percent reduction of the payload in orbit. For no added booster weight, increasing vertical rise time from 16-7 to 100 percent of booster burning time (so that the spent booster would impact in the launch area) reduced the payload by 37 percent. Increasing the vertical rise time from 16-7 to 50 percent of booster burning time resulted in about a 15-percent reduction in the impact distance, and for vertical rise times greater than 50-percent the impact distance decreased rapidly.

Levin, Alan D.↗
NASA NTRS1990

Gamma guidance of trajectories for coplanar, aeroassisted orbital transfer

The optimization and guidance of trajectories for coplaner, aeroassisted orbital transfer (AOT) from high Earth orbit (HEO) to low Earth orbit (LEO) are examined. In particular, HEO can be a geosynchronous Earth orbit (GEO). It is assumed that the initial and final orbits are circular, that the gravitational field is central and is governed by the inverse square law, and that at most three impulses are employed: one at HEO exit, one at atmospheric exit, and one at LEO entry. It is also assumed that, during the atmospheric pass, the trajectory is controlled via the lift coefficient. The presence of upper and lower bounds on the lift coefficient is considered. First, optimal trajectories are computed by minimizing the total velocity impulse (hence, the propellant consumption) required for AOT transfer. The sequential gradient-restoration algorithm (SGRA) is used for optimal control problems. The optimal trajectory is shown to include two branches: a relatively short descending flight branch (branch 1) and a long ascending flight branch (branch 2). Next, attention is focused on guidance trajectories capable of approximating the optimal trajectories in real time, while retaining the essential characteristics of simplicity, ease of implementation, and reliability. For the atmospheric pass, a feedback control scheme is employed and the lift coefficient is adjusted according to a two-stage gamma guidance law. Further improvements are possible via a modified gamma guidance which is more stable with respect to dispersion effects arising from navigation errors, variations of the atmospheric density, and uncertainties in the aerodynamic coefficients than gamma guidance trajectory. A byproduct of the studies on dispersion effects is the following design concept. For coplaner aeroassisted orbital transfer, the lift-range-to-weight ratio appears to play a more important role than the lift-to-drag ratio. This is because the lift-range-to-weight ratio controls mainly the minimum altitude (hence, the peak heating rate) of the guidance trajectory; on the other hand, the lift-to-drag ratio controls mainly the duration of the atmospheric pass of the guidance trajectory.

Miele, A.↗
NASA NTRS1985

Analysis of the free-tip rotor wind-tunnel test results

The results from a wind tunnel test of a small scale free-tip rotor are analyzed. The free-tip rotor has blade tips that are free to weathervane into the tip's relative wind, thus producing a more uniform lift around the azimuth. The free-tip assembly, which includes the controller, functioned flawlessly throughout the test. In a test of the free-tip's response after passing through a vertical air jet, the tip pitched freely and in a controlled manner. Analysis of the tip's response characteristics showed the free-tip system's damped natural frequency to be 5.2 per rev. Tip pitch angle responses to the local airstream are presented for an advance-ratio range of 0.1 to 0.397 and for a solidity weighted rotor lift coefficient range of 0.038 to 0.092. Harmonic analysis of the responses showed a dominance by the first harmonic. As a result of the tip being free, forward flight power requirements were reduced by 8% or more. More power reduction was recorded for high thrust conditions. In addition to the power reduction, flatwise blade bending moments were reduced by as much as 30% at the inboard blade stations.

Stroub, Robert H.↗
NASA NTRS1976

Evaluation of ice and frost accumulation on the Space Shuttle external tank

Ice/frost formation on the Space Shuttle cryogenic propellant tanks presents a different problem from that of past launch vehicles. Lift off weight addition has been the primary concern on past launch vehicles. The primary ice/frost concern on the Shuttle vehicle is damage to the Orbiter Thermal Protection System due to ice/frost impact. The approach used to arrive at a solution to this unique Shuttle problem is presented. The launch vehicle configuration selected and its limitations are described, along with contingency ground support equipment.

Rhodes, R. E.↗
NASA NTRS1983

Aerobraking of a low L/D manned vehicle from Geo return to rendezvous with the Space Shuttle

The results of a study of the airbraking portion of the flight of an Apollo class vehicle designed for a sortie from the Orbiter to Geo and return to Leo for Orbiter retrieval are presented. An ablative heat shield would be used on the vehicle to shed velocity to speeds commensurate with Orbiter rendezvous. A reference design was selected for a spacecraft configuration with an L/D ratio of 0.3 and a weight to lift surface ratio of 236 lb/sq ft. Atmospheric guidance would consist of using the bank angle for altitude and inclination angle control and an equilibrium bank angle was defined. The vehicle would have a maximum temperature, considering a reference sphere, of 4800 F and a peak load of about 2 g. Atmospheric exit parameters were also determined, together with minimum delta-V for rendezvous.

Gamble, J. D.↗
NASA NTRS1991

Overview of the Beta II two-stage-to-orbit vehicle design

A design concept for fully reusable two-stage-to-orbit (TSTO) vehicle is reviewed in terms of adapting the Beta vehicle to revised mission requirements. The Beta II vehicle is discussed in terms of study-mission requirements such as horizontal takeoff and landing, a 10,000-lb payload, and a 120-nm polar orbit. The fully reusable TSTO concept specified in the study is found to be feasible with a moderate gross lift-off weight particularly if air-breathing propulsion is incorporated.

Plencner, Robert M.↗