Search NASA⌕ Search

SEARCH · Search NASA

Results for “Wind Tunnel Test Results”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Analysis of wind tunnel test results for a 9.39-per cent scale model of a VSTOL fighter/attack aircraft. Volume 2: Evaluation of prediction methodologies

An evaluation of current prediction methodologies to estimate the aerodynamic uncertainties identified for the E205 configuration is presented. This evaluation was accomplished by comparing predicted and wind tunnel test data in three major categories: untrimmed longitudinal aerodynamics; trimmed longitudinal aerodynamics; and lateral-directional aerodynamic characteristics.

Lummus, J. R.↗
NASA NTRS1983

STOL wind tunnel test results for a tactical supercruiser

Attention is given to the NASA Langley Research Center's testing of a 10.5 percent-scale supersonic cruiser (supercruiser) aircraft model in its V/STOL wind tunnel, in order to investigate the low speed aerodynamic characteristics of STOL enhancement devices. The STOL devices employed by the supercruiser configuration are high vector angle ramp nozzles, working in conjunction with a remote augmented lift system (RALS), in addition to a canard trim system. Also investigated were thrust reverser/ground plane interaction effects, for the evaluation of landing characteristics. It is noted that STOL approach thrust management requires the use of a partially reversing RALS nozzle which develops approximately 31 percent of main nozzle thrust, and that strong nose-up interactions during ground roll, with reverser operation, may limit dry power engine thrust for braking assistance to about 50 percent of maximum dry power.

Hutchison, R. A.↗
NASA NTRS2004

Wind Tunnel Test Results for Gas Flows Inside Axisymmetric Cavities on Cylindric Bodies with Nose Cones

Experimental test results of air flow inside and at the cylindrical cavity located on axisymmetric body are presented. These tests were conducted in the wind tunnel A-7 of Institute of Mechanics at Moscow State University. Pressure distribution along the cavities and optical measurements were obtained. Dependence of these characteristics of length of a cavity in the range: L/D = 0.5 - 14 and free stream Mach in the range: M(sub infinity) = 0.6 - 3.0 was determined. Flow structure inside the cavity, cause of flow regime change, separation zones geometry and others were studied. In particular, the flow modes of with open and closed separation zones are determined.

Shvets, A. L.↗
NASA NTRS1974

Wind Tunnel Test Results of Fairings on A.004 Scale Model Rockwell Space Shuttle Integrated Vehicle Aerodynamic Characteristics at Mach Numbers from 0.6 to 4.96 (IA62F)

Experimental aerodynamic investigations were conducted on a .004 scale model (34-OTS) orbiter, external tank, and solid rocket booster combined as an integrated vehicle in the NASA/MSFC 14 x 14 inch trisonic wind tunnel. The primary test objective was to determine the effect of a full length orbiter/external tank fairing on axial force. Secondary objectives were to define the static stability characteristics of the mated vehicle configuration with fairings over a Mach number range of 0.6 thru 4.96. Six component aerodynamic force and moment data were recorded over an angle of attack range from -10 deg to 10 deg at 0 deg sideslip angle and from -10 deg to 10 deg sideslip range at 0 deg and 5 deg angle of attack. Plotted and tabular results are presented herein.

Allen, E. C.↗
NASA NTRS1985

Free-Tip Rotor Wind Tunnel Test Results

A new rotor blade tip design called the free-tip has been proposed as a means to improve forward flight performance characteristics and reduce oscillatory loads. The free-tip design incorporates a tip that is free to pitch independently of the rest of the blade. Pitching about an axis forward of the quarter-chord, the tip weathervanes into its local wind, thus reducing angle of attack perturbations and the resulting oscillatory lift loadings. A nearly constant nose-up pitching moment is applied mechanically to the tip so that the tip, to maintain pitching equilibrium, produces nearly steady positive lift around the azimuth. A wind-tunnel test of a small-scale, 5.1 m diameter model rotor was conducted to obtain comparative forward flight performance and oscillatory loads data with the tips free and fixed. The free-up was shown to reduce power in trimmed flight over a wide range of advance ratio and thrust; at an advance ratio of 0.3 and C(sub L)/sigma of 0.08 the reduction is 12%. Oscillatory flapwise bending-moments and oscillatory pitch link loads are also reduced, but the oscillatory in-plane bending moments increase.

Stroub, Robert H.↗
NASA NTRS2011

An Assessment of Ares I-X Aeroacoustic Measurements with Comparisons to Pre-Flight Wind Tunnel Test Results

During the recent successful launch of the Ares I-X Flight Test Vehicle, aeroacoustic data was gathered at fifty-seven locations along the vehicle as part of the Developmental Flight Instrumentation. Several of the Ares I-X aeroacoustic measurements were placed to duplicate measurement locations prescribed in pre-flight, sub-scale wind tunnel tests. For these duplicated measurement locations, comparisons have been made between aeroacoustic data gathered during the ascent phase of the Ares I-X flight test and wind tunnel test data. These comparisons have been made at closely matching flight conditions (Mach number and vehicle attitude) in order to preserve a one-to-one relationship between the flight and wind tunnel data. These comparisons and the current wind tunnel to flight scaling methodology are presented and discussed. The implications of using wind tunnel test data scaled under the current methodology to predict conceptual launch vehicle aeroacoustic environments are also discussed.

Nance, Donald K.↗
NASA NTRS1975

Comparison of wind tunnel test results at free stream Mach 0.7 with results from the Boeing TEA-230 subsonic flow method

The use of the Boeing TEA-230 Subsonic Flow Analysis method as a primary design tool in the development of cruise overwing nacelle configurations is presented. Surface pressure characteristics at 0.7 Mach number were determined by the TEA-230 method for a selected overwing flow-through nacelle configuration. Results of this analysis show excellent overall agreement with corresponding wind tunnel data. Effects of the presence of the nacelle on the wing pressure field were predicted accurately by the theoretical method. Evidence is provided that differences between theoretical and experimental pressure distributions in the present study would not result in significant discrepancies in the nacelle lines or nacelle drag estimates.

Mohn, L. W.↗
NASA NTRS1981

Low and high speed propellers for general aviation - Performance potential and recent wind tunnel test results

A survey is presented of current research efforts in general aviation, low-speed propeller design and high-speed propfan design, with attention on such features as (1) advanced blade shapes, with novel airfoils and sweep, (2) tip devices, (3) integrated propeller/nacelle designs, (4) area-ruled spinners, (5) lightweight, all-composite blade construction, and (6) contra-rotating propfan systems. The potential overall improvements associated with these design modifications are calculated to lie at 10-15% for low-speed rotors and 15-30% for high-speed ones. Emphasis is placed on noise reduction, blade drag, performance prediction methods and wind tunnel testing of alternative rotor configurations. Extensive use of graphs is made in performance comparisons between alternative blade and rotor designs.

Jeracki, R. J.↗
NASA NTRS2018

Initial Calibrations and Wind Tunnel Test Results for an In-Flow Reference Array Using New In-Flow Acoustic Sources in Four Array Mount Configurations

This paper describes efforts to develop a small in-flow phased microphone array as a reference acoustic sensor and quantify its level-measurement accuracy with new in-flow calibration sources. The devices can be applied to a wide variety of in- and out-of-flow measurement applications and test facilities. Recent tests of the array and two calibration sources in the NASA Anechoic Chamber and Army 7- by 10-foot Wind Tunnel at NASA Ames Research Center demonstrated that the array was functional over a frequency range of 2 to 100 kilohertz for emission angles of 92 degrees, 108 degrees, and 120 degrees, and Mach numbers of 0, 0.15, and 0.25. The array and calibration sources were then used to assess the relative effects of array installation on background noise and level measurement accuracy by locating the array in the flow (strut- and wall-mounted) as well as outside the flow behind a porous wall screen and a free shear layer. The wind tunnel array measurements were compared with anechoic chamber measurements using discrete microphones at the same source distance and emission angles. At 92 degrees, the noise floor and attenuation spectra were comparable (within 5 decibels) for each installation from 2 to 30 kilohertz. At higher angles, the array installation behind the Kevlar screen had the lowest noise floor at M = 0.15 and 0.25. The array installation 10 inches (maximum available distance) behind a free shear layer had higher background noise that is typically reduced to a lower level by moving the array back further from the flow. For emission angles greater than 92 degrees, both the Kevlar and free shear layer installations exhibited stronger attenuations in measured level, beginning at lower frequencies than either the wall- or strut-mount configurations. Additional array and calibration source units of the same design are being tested at NASA’s Glenn Research Center and Langley Research Center in their aeroacoustic research facilities in an effort to improve measurement accuracy and repeatability.

Aeroacoustic Wind Tunnel Research↗
NASA NTRS1996

Wind tunnel test results of a 1/8-scale fan-in-wing model

A 1/8-scale model of a fan-in-wing concept considered for development by Grumman Aerospace Corporation for the U.S. Army was tested in the Langley 14- by 22-Foot Subsonic Tunnel. Hover testing, which included height above a pressure-instrumented ground plane, angle of pitch, and angle of roll for a range of fan thrust, was conducted in a model preparation area near the tunnel. The air loads and surface pressures on the model were measured for several configurations in the model preparation area and in the tunnel. The major hover configuration change was varying the angles of the vanes attached to the exit of the fans for producing propulsive force. As the model height above the ground was decreased, there was a significant variation of thrust-removed normal force with constant fan speed. The greatest variation was generally for the height-to-fan exit diameter ratio of less than 2.5; the variation was reduced by deflecting fan exit flow outboard with the vanes. In the tunnel angles of pitch and sideslip, height above the tunnel floor, and wind speed were varied for a range of fan thrust and different vane angle configurations. Other configuration features such as flap deflections and tail incidence were evaluated as well. Though the V-tail empennage provided an increase in static longitudinal stability, the total model configuration remained unstable.

Wilson, John C.↗
NASA NTRS1987

Wind tunnel test results of heavy rain effects on airfoil performance

The effects of simulated heavy rain on the aerodynamic characteristics of a NACA 64-210 airfoil section equipped with high-lift devices were investigated in the NASA Langley 14- by 22-Foot Subsonic Tunnel. The experiment was part of an on-going NASA program to determine the effect of heavy rain on airplane performance, and was directed at providing insight into scaling laws for subscale model testing of rain effects. The model used in the investigation had a chord of 2.5 feet, a span of 8.0 feet, and was mounted on the tunnel centerline between two large endplates. A water spray distribution system was located 10 chord lengths upstream of the model. The sensitivity of test results to partial-span coverage of the model in the simulated rain environment as compared to full-span coverage was also investigated. The lift and drag data obtained for the high-lift configuration show excellent repeatability of results compared to the previous data. Results obtained for various spray concentrations and tunnel speeds showed significant losses in maximum lift capability, a decrease in the angle of attack for maximum lift, and an increase in drag as the stimulated rain rate was increased. The test results also indicated that the data were not strongly affected by surface tension effects for the high-lift configuration.

Bezos, G. M.↗
NASA NTRS1983

An experimental investigation of a free-tip rotor configuration in a forward flight wind-tunnel test

Results from an experimental evaluation of a free-tip rotor are presented. The evaluation included whirl tests and wind tunnel tests up to advance ratios of 0.4. The free tip extended over the outer 5% of the rotor blade and included a passive mechanical controller whose output characteristics were varied. The controller configuration combined with the free tip aerodynamics resulted in higher power requirements, because the tip's pitch angle was 5 to 10 degrees greater than that of the inboard portion of the blade, and its pitching motion capability was considered to be inhibited by frictional forces. Recommendations are included for design features for a follow-on test.

Stroub, R. H.↗