Search NASA⌕ Search

SEARCH · Search NASA

Results for “Writing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Multi-material direct ink writing and co-sintering of gadolinium oxide – zirconium oxide components

Methods for fabrication of multi-material or functionally graded ceramic composite architectures are of interest for numerous applications. However, conventional co-sintering of multi-material ceramic parts is a challenge because differences in the sintering behavior of the two materials leads to interfacial strain and, ultimately, component failure. Direct ink writing (DIW) is an extrusion-based additive manufacturing process that excels at multi-material printing because multiple extrusion nozzles can be installed on the same gantry system. Furthermore, the use of DIW as a method to fabricate multi-material ceramic green bodies offers an additional variable for controlling and potentially matching sintering kinetics in the slurry formulation used for two dissimilar feedstocks. In the work documented in this manuscript, we explored two strategies to successfully co-sinter multi-material ceramic oxides: slurry optimization to match sintering kinetics and material gradients to step from one material to another. This manuscript also quantifies the allowable mismatch that avoids part cracking in solid solution forming multi-material systems and discusses best strategies to reduce mismatch during co-sintering. Inks composed of gadolinium oxide (Gd 2 O 3 ) and zirconium oxide (ZrO 2 ), a surrogate for uranium oxide (UO 2 ), were thermally matched, which resulted in a sintering mismatch reduction of over 10%. It was found that ~1% mismatch is tolerable during debind cycles and that ~5% mismatch is manageable during sintering cycles after slurry formulations are optimized to match the sintering behavior. Use of continuous gradients is shown to reduce sintering mismatch, although geometric resolution may be lost due to solid solution formation.

Snarr, Patrick L. [Oak Ridge National Laboratory (↗
DOE OSTI2025

ATLAS HL-LHC Demonstrators with Data Carousel: Dataon-Demand and Tape Smart Writing

The High Luminosity upgrade to the LHC (HL-LHC) is expected to deliver scientific data at the multi-exabyte scale. To tackle this unprecedented data storage challenge, the ATLAS experiment initiated the Data Carousel project in 2018. Data Carousel is a tape-driven workflow in which bulk production campaigns with input data resident on tape are executed by staging and promptly processing a sliding window to disk buffer such that only a small fraction of inputs are pinned on disk at any one time. Put in ATLAS production before Run3, Data Carousel continues to be our focus for seeking new opportunities in disk space savings, and enhancing tape usage throughout the ATLAS Distributed Computing (ADC) environment. These efforts are highlighted by two recent ATLAS HL-LHC demonstrator projects: data-on-demand and tape smart writing. In this paper, we will discuss the recent studies and outcomes from these projects. The research was conducted together with site experts at CERN and Tier-1 centers.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Topological Magneto-optics in the Noncoplanar Antiferromagnet Co 1/3 ⁢NbS 2 : Imaging and Writing Chiral Magnetic Domains

Despite its tiny net magnetization, the antiferromagnetic (AFM) van der Waals material Co 1/3 ⁢NbS 2 exhibits a large transverse Hall conductivity 𝜎 𝑥⁢𝑦 even at zero applied magnetic field, which arises, as recently shown, from the topological nature of its noncoplanar “tetrahedral” AFM order. Here, this triple-𝐪 magnetic order can be regarded as the short-length-scale limit of a magnetic skyrmion lattice and has an intrinsic spin chirality. Here, we show, using optical wavelengths spanning the ultraviolet to infrared (400–1000 nm), that magnetic circular dichroism provides an incisive optical probe of the topological AFM order in Co 1/3 ⁢NbS 2 . Measurements as a continuous function of photon energy are directly compared with first-principles calculations, revealing the influence of the underlying quantum geometry on optical conductivity. Leveraging the power and flexibility of optical methods, we use scanning magnetic circular dichroism microscopy to directly image chiral AFM domains and demonstrate writing of chiral AFM domains.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Adhesion Testing of Direct-Write Printed Ink on Metallic Structural Components

The successful adoption of additive manufacturing for the rapid prototyping of direct-write printed electronics requires the establishment of quantifiable metrics that can interrogate device performance. One measure of performance is the adhesion strength between the substrate and printed film interface, which is critical since the strength of this interface can dictate the accuracy and reliability of the printed device. In this work, a non-contact laser-induced spallation technique was used to quantify the adhesion of silver printed films on aluminum alloy substrates. The laser-based method was compared to a standardized pull-off adhesion test, which provided baseline measurements of adhesion strength. The sintering conditions were shown to play an important role in the film-substrate adhesion strength, as well as the cohesion and ductility of the film itself. The methods and results described in this work support the establishment of process control steps that are necessary for quickly verifying the reliability of printed devices prior to their deployment in critical experiments.

Adhesion test↗
DOE OSTI2024

Selective Deposition and Fusion of AISI 316L: An Additive Manufacturing Process for Space Environments via Direct Ink Writing and Laser Processing

Unlocking the potential of additive manufacturing (AM) for space exploration hinges on overcoming key challenges, notably the ability to manufacture or repair parts on-site during exploration missions with consideration of quality, feedstock utilization, and challenges involved in microgravity environments. While there are multiple efforts to investigate the use of existing metal AM processes such as powder bed fusion (PBF), directed energy deposition (DED), and filament-based material extrusion, each process comes with a different set of challenges in space environments. Here, in this work, we introduce a new AM method that integrates the benefits of direct ink writing (DIW) to selectively deposit metallic pastes with laser-based processing to locally debind and subsequently melt and fuse metal powder, layer by layer, enabling the manufacturing of AISI 316L samples with densities exceeding 99.0%. The impact of process parameters on single-track dimensions, surface morphology, and porosity was characterized. The efficacy of laser debinding was assessed via secondary-ion mass spectrometry, permitting the carbon content to be estimated at 0.0152%, which is safely below the acceptable limit (0.03 wt%) for AISI 316L.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Direct Ink Write and Processing of Complex 3D Marine Compatible Structures with Calcium Carbonate Slurries

Ocean acidification heavily impacts marine ecosystems by reducing calcification. Many coral-algae symbiotic relationships are in jeopardy due to the destruction of coral reefs. Here, a ceramic ink compatible with the direct ink write additive manufacturing technique was formulated and used to print marine compatible structures that could grow algae and restore that relationship. A diacrylate polymer was mixed with calcium carbonate, a material that comprises a coral skeleton, to create a slurry with shear thinning properties. Rheology studies were conducted to confirm printing properties and characterize the slurry. Printed parts demonstrated strong control over print features, including size and infill design. Various infill patterns and percentages were attempted to optimize printability and potential algae growth. Thermogravimetric analysis helped determine a logical burnout and sintering procedure to avoid large cracking. This project developed a printable and sinter-able calcium carbonate ceramic slurry for complex marine-compatible structures and algae growth. This research was conducted in the support of the Eco Reef project.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Nonlinear viscoelastic response of silicone additively manufactured direct ink write (DIW) foams under repetitive compression

To investigate dynamic fatigue behavior of foam in military protective applications, such as helmets, additively manufactured (AM) foams were compressively strained into the plateau region using a reduced design of experiments. A simple power law was found to govern the decline in dynamic stiffness (complex modulus) as the foams underwent the purchase order requirement of 10,000 cycles of small deformation in the plateau region. This rate of decline was newly found to correlate with the degree of nonlinearity in the material’s deformation, quantified using total harmonic distortion. Materials with low nonlinearity exhibited relatively stable stiffness across cycles, while those with high nonlinearity experienced greater losses. The observed nonlinearity depended on both applied stress and strain rate. A strong linear correlation (R 2 = 0.78) was identified between second-order nonlinearity and the time-dependent stiffness response. Two lattice structures were examined: face-centered tetragonal (FCT) and simple cubic (SC). The SC material exhibited higher total harmonic distortion (5%) and lower stiffness retention than the FCT (2%). In conclusion, these results suggest that for cyclic compression applications in a wide variety of industries such as packaging, personal protective equipment, or aerospace, selecting materials with lower stress and greater structural uniformity can enhance the stability of dynamic performance.

42 ENGINEERING↗
DOE OSTI2025

Development of direct ink write radially graded alumina/zirconia

Functionally graded materials (FGMs) are of interest in multiple fields, yet many materials combinations are limited by coefficient of thermal expansion (CTE) mismatch. Here, a radially graded alumina/yttria-doped zirconia (Al 2 O 3 /8YZ) FGM is used to demonstrate processing strategies to mitigate CTE and sintering behavior differences between these oxides. FGM materials are especially sensitive to ink stability during printing, as all components (in this case, Al 2 O 3 and 8YZ) must be stabilized in the same dispersant or additive solution. Thus, this system is also ideal to demonstrate ink optimization best practices. Materials were characterized throughout processing to correlate the effects of common additives on both the ceramic particle suspensions and final sintered components. Aggregation observed in the initial additive-containing suspensions were present in the sintered component. The differences in sintering onset temperature and shrinkage rate resulted in internal stresses within the sintered component, which ultimately caused mechanical failure of the component under low stress. In conclusion, a processing strategy was recommended to mitigate the sintering behavior mismatch of alumina and 8 wt% yttria-stabilized zirconia.

Lamm, Benjamin W. [Oak Ridge National Laboratory (↗
DOE OSTI2025

Direct writing of PVBVA/Ti 3 C 2 T x (MXene) triboelectric nanogenerators for energy harvesting and sensing applications

Triboelectric nanogenerators (TENGs) have gained recognition for their potential to convert mechanical energy into electrical energy, making them attractive for applications in healthcare, robotics, and human-device interfaces. However, many TENG devices rely on fluorinated polymers for high charge generation and involve complex fabrication processes, which limit their practicality and environmental sustainability. Here, we developed an eco-friendly composite of poly (vinyl butyral-co-vinyl alcohol-co-vinyl acetate) (PVBVA) and Ti 3 C 2 T x MXene for extrusion printing onto aluminum foil substrates, enabling the additive manufacturing of TENGs. Experimental results indicate that integrating 5.5 mg mL -1 of MXene (P-MX 5.5) into PVBVA resulted in a power density of 760 mW·m -2 , with simultaneous improvements in open-circuit voltage (129 %) and short-circuit current (250 %), demonstrating enhanced charge transfer efficiency. Beyond aluminum foil-based devices, we further explored the fully printed P-MX 5.5 TENG by utilizing silver ink electrodes, eliminating the need for aluminum foil. This fully printed, flexible TENG was successfully used for real-time human motion sensing, demonstrating its ability to detect activities such as walking, running, knee bending, and jumping. Collectively, our additively manufactured and sustainable PVBVA-MXene TENG composites, including both aluminum-based and fully printed versions, show promise for future energy harvesters, sensors, wearable electronics, healthcare, and robotic applications.

Additive manufacturing↗
DOE OSTI2025

UV-Enabled Defect Engineering in Multilayer GaSe and InSe and UV Writing of the Grating Pattern

III–VI post-transition-metal chalcogenides are layered semiconductor materials that exhibit direct band gaps in multilayers. Defect engineering is essential in 2D layered semiconductors for functional devices. Here, in this work, we report defect engineering in multilayer gallium selenide (GaSe) and indium selenide (InSe), where defects generated by ultraviolet (UV, 325 nm) laser irradiation result in an additional photoluminescence (PL) line. The additional PL line is due to defect-bound excitons. Characteristics of the defect emission are similar in GaSe and InSe samples subjected to UV irradiation, air annealing, and hydrostatic pressure. Two-beam UV interference was applied to create grating patterns with a periodic array of low and high densities of defects in GaSe. Density functional theory has identified the defect type in GaSe. The results provide valuable insights into defect generation and UV scribing of photonic circuits in 2D Se-based multilayers for optical integration in a 2D platform.

2D multilayered materials↗
DOE OSTI2026

Electrically writing a magnetic heliknoton in a chiral magnet

A magnetic heliknoton is the three-dimensional counterpart to the two-dimensional magnetic skyrmion, and serves as a pivotal topological soliton for extending topological magnetism into three dimensions. However, its experimental realization remains elusive. Here we report the controlled nucleation of a magnetic heliknoton in the chiral magnet FeGe at zero magnetic field, achieved through nanoscale current-pulse excitation. By combining angle-dependent quantitative electron holography with micromagnetic simulations, we resolve the three-dimensional spin texture of the heliknoton. In particular, the heliknoton exhibits current-driven collinear motion without the Hall effect. Furthermore, our findings establish a readily accessible experimental platform for further exploration of three-dimensional topological solitons and highlight their potential for practical applications.

Magnetic properties and materials↗
DOE OSTI2025

Curing inhibition and shelf stability in silicone formulations for direct ink writing

Various potential hydrosilylation inhibitors were incorporated into a silicone formulation for 3D printing. Different inhibitors resulted in peak cure temperatures from 42.8 to 180.3°C. The curing behavior of formulations with 1-ethynyl-1-cyclohexanol (ETCH), which exhibited a peak cure temperature of 98.4°C, was characterized for different ETCH concentrations and storage conditions. The curing was modeled using time temperature superposition, revealing an activation barrier of 89 kJ/mol. Overall, characterization resulted in a conservative recommended shelf life of 90 days. In conclusion, these studies offer insights into the stability of these formulations and the importance of inhibition for producing reliable, printable inks.

36 MATERIALS SCIENCE↗
DOE OSTI2025

MontePy: a Python library for reading, editing, and writing MCNP input files.

The Monte Carlo N-Particle (MCNP) radiation transport code is a highly capable and accurate code with a long legacy. MCNP uses the Monte Carlo simulation process to simulate the path of particles (e.g., neutrons, photons, charged particles, etc.), and their interaction with materials. It is widely used in nuclear engineering, high-energy physics, and other fields. Its origins in the mid-twentieth century predate many modern software conventions. MCNP users provide an input file to MCNP, which it then uses to create an internal representation of the simulation problem. These input files originally had to be stored as punchcard decks, and the user manual still uses the terminology of cards and decks, despite moving beyond punchcards. MCNP predates nearly all modern human readable markup or data serialization languages, such as the extensible Markup Language (XML), the Standard Generalized Markup Language (SGML), YAML (YAML Ain’t Markup Language), and Javascript Object Notation (JSON). Due to this, MCNP uses an entirely custom defined syntax language for its input, making off-the-shelf libraries for XML, YAML, and JSON impossible to use for scripting various operations on MCNP input files (Kulesza et al., 2022).

97 - MATHEMATICS AND COMPUTING↗