SEARCH · Search NASA
Results for “activated carbon”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Success Using A Granular-Activated Carbon Filtration Swab to Rehabilitate Westbay{sup R} Multi-level Groundwater Monitoring Wells at the INL - 20544
In November 2015, tetrachloroethylene (PCE) was discovered in groundwater samples collected from a Westbay{sup R} multi-level groundwater monitoring well at the Idaho National Laboratory (INL).a Subsequent investigation determined that PCE was not present in the groundwater. The detected PCE was instead due to inadvertent contamination of the internal tubing fluid in the Westbay well-monitoring system, which is isolated from the surrounding groundwater. Further investigation showed that three of the 11 Westbay wells at the INL contained PCE-contaminated tubing fluid at concentrations above the U.S. Environmental Protection Agency's maximum contaminant level for drinking water (5 μg/L). Loose sediment at the bottom of some Westbay wells was also found to contain PCE; the three wells were then identified for rehabilitation as part of the INL well maintenance program. The unique construction of the Westbay wells - i.e., the small diameter (5.72 cm [2.25 in.]) and the depths of the tubing fluid ranging from 144.8 to 419 m (475 to 1,376 ft) below ground surface - posed unique challenges to the rehabilitation. Because the tubing fluid provides structural integrity, the fluid cannot be removed and then replaced without damaging the integrity of the Westbay well. Additionally, the small diameter of the systems and the associated depths limit the availability of equipment that can be used for the rehabilitation. After an evaluation of potential methods, it was determined that the use of an in-well, custom-fabricated, granular-activated-carbon filtration swab deployed via a wire line would provide the safest and most cost-effective method for rehabilitation. Westbay well rehabilitation started at well MIDDLE-2051 in late June 2018 and paused in December 2018 for the season. The PCE concentration in the tubing fluid at MIDDLE-2051 was initially reduced to a maximum concentration of 3.81 μg/L from a maximum of 642 μg/L, while the concentration of PCE in the sediment had been reduced from 5,360 to 2,270 μg/kg. Sampling was performed at MIDDLE-2051 again in August 2019, and the tubing fluid increased to a maximum concentration of 45.4 μg/L, while the concentration in the sediment decreased further to 1,890 μg/kg due to desorption of PCE from the sediment to the tubing fluid. Rehabilitation resumed at well MIDDLE-2050A in late August 2019, and the PCE concentration in the tubing fluid had been reduced to a maximum concentration of 19.0 μg/L. Although the method has been shown to be time-consuming, it has proven to be effective and safe for personnel performing the work and to the integrity of the well. Future sample data results at all wells will help determine an estimated completion of the rehabilitation. (authors)
Effect of Changing Amounts of Promoters and Base Fe Metal in a Multicomponent Catalyst Supported on Coal-Based Activated Carbon for Fischer–Tropsch Synthesis
The effect of varying the amounts of metals Fe, Cu, K, and Mo was studied on a catalyst supported on activated carbon (AC), which is an item of novelty of this paper. The base-case catalyst contains 16% Fe, 0.9% K, 6% Mo, and 0.8% Cu relative to the AC support. For all of the catalysts used, alcohol production is small. The production of hydrocarbons depends upon the amount of Fe and other promoters used. The amount of Fe was increased from 0% to 32% on the catalyst containing base-case amounts of the other materials. While 0% Fe shows no activity towards Fischer–Tropsch synthesis (FTS), 32% Fe shows a marginal increase in FTS activity when compared with 16% Fe. Furthermore, the amount of K was increased from 0% to 1.8%, with the other metals in their base-case amounts. The selectivity of C1–C4 decreases with the addition of K, while the selectivity of C5+ increases. Analogously, the amount of Mo was increased from 0% to 12%. A small amount of Mo results in an increase in FTS activity but decreases with the addition of more Mo. Cu on the catalyst was increased from 0% to 1.6%, with 0.8% Cu proving optimum for FTS.
Highly efficient separation membrane based on cellulose acetate/chitosan fibrous composite substrate with activated carbon functional adsorption layer
Abstract BACKGROUND For improving the permeability and selectivity of adsorption separation membranes, membrane materials, structural morphology and separation technology must continue to be investigated. Development of a membrane that is environmentally friendly, cost‐effective and with high filter precision is an important direction in current research. RESULTS The air pressure spraying method was used to prepare an activated carbon (AC)–cellulose acetate/chitosan (CA/CS) composite membrane. The CA/CS fiber composite membrane was prepared as substrate layer, and AC was loaded on the surface of the CA/CS composite membrane as a functional adsorption layer. When the spraying pressure was 0.01 MPa and the mass ratio of AC/CS was 2:1, a composite membrane with even and compact morphology could be obtained. Both the compact AC functional layer and complete CA/CS substrate layer endowed the AC–CA/CS composite membrane with an excellent water filtration property. At low feeding pressure, the permeate flux and rejection rate of bisphenol A (BPA) could reach 9.27 × 10 3 L m −2 h −1 and 98.31%, respectively. Meanwhile, the adsorption capacities of the membrane were investigated. It tended to equilibrate quickly in 2 min for dyes and BPA. The equilibrium adsorption capacities of the membrane for acid blue, acid yellow and BPA were 175.80, 164.0815 and 79.58 mg g −1 , respectively. The adsorption process conformed to pseudo‐second‐order kinetics and the Langmuir monolayer adsorption model. CONCLUSIONS This work could provide a practical and effective feasibility for membrane separation technology. © 2020 Society of Chemical Industry (SCI)
Spectral induced polarization signatures of smoldering remediation enhanced with colloidal activated carbon: An experimental study
Monitoring the remediation of soil and groundwater contaminated by organic compounds remains highly challenging. The spectral induced polarization (SIP) method exhibits significant promise for monitoring changes to the electrical properties of soils that are undergoing remediation. Thermal treatments, such as smoldering combustion, have become established remediation techniques for destroying contaminants. Smoldering combustion is now being supported by colloidal activated carbon (CAC), with CAC able to adsorb contaminants and supplement the fuel source for destroying contaminants. The objective of this study is to investigate the potential of SIP for tracking the smoldering remediation of imitated field soils supplemented with CAC. SIP column experiments were first conducted to assess the response of SIP to varying concentrations of CAC in field soils that contain, or do not contain, organic material (OM). Here these results demonstrate that increasing OM and CAC contents increase both the real and imaginary components of the complex conductivity, with the imaginary conductivity also showing frequency dependence. Next, a suite of smoldering and SIP column experiments was conducted to investigate if SIP can detect changes in imitated field soils of varying OM and CAC contents that have been remediated by smoldering combustion. The SIP results on the examined soils both before and after smoldering show that SIP can detect changes in the real conductivity, and particularly the imaginary conductivity, between different soil compositions and different stages of the remediation process. High resolution scanning electron microscopy (SEM) imaging was performed on all samples to validate the SIP and smoldering experiments, confirming significant reductions in carbon after smoldering. Overall, this study suggests that SIP has potential to detect changes in the electrical properties of field soils due to the addition of remedial fluids like CAC and contaminant destruction by smoldering remediation.
Renewable Activated Carbon Sorbent for the Desulfurization of Liquid Fuels
In recent years, significant efforts have been devoted to the reduction of sulfur levels in transportation fuels in order to reach regulatory limits and reduce the emission of harmful SO x into the atmosphere. In particular, adsorptive desulfurization (ADS) has the potential to produce zero-sulfur fuels without the need for a high energy intensity process, high H 2 pressure, and long process times as in the case of other technologies such as hydrodesulfurization. In this work, we have demonstrated the effectiveness of renewable activated carbons derived from food waste (FWAC) for the ADS of model jet and diesel fuels. The optimal FWAC materials were those fabricated to maximize the micropore volume, providing available sites for the adsorption of dibenzothiophene (DBT) and dimethyldibenzothiophene (DMDBT). The FWAC had a greater sulfur adsorption capacity than commercial AC, Y zeolite sorbents, and AC derived from other biomass sources including miscanthus, coconut shell, and walnut shell. Elemental analysis suggests that the inorganic impurities inherent in food waste, notably K, Ca, P, and Na, may contribute to its improved sulfur adsorption compared to other AC materials. Microscopy and X-ray diffraction studies further demonstrated the presence of inorganic species on FWAC that may provide active sites for the chemisorption of sulfur molecules.
Toluene adsorption and capacity regeneration using zeolite-based monolith and activated carbon fiber felt
Common adsorbents studied to remove volatile organic compounds (VOCs) from indoor air can release previously adsorbed VOCs back into the indoor space when the adsorbent is saturated or if the VOC concentration fluctuates. A durable adsorbent with a continuous regeneration strategy could prevent this recontamination of the indoor air and reduce adsorbent disposal waste. A deeper understanding of the adsorption and desorption behavior of VOC adsorbents is needed to create an efficient regeneration strategy. This study investigated the adsorption and thermal desorption behavior of toluene on two different adsorbents, (1) a zeolite-based adsorbent and (2) an activated carbon fiber (ACF) felt. Consistent adsorption behavior across a series of toluene concentrations was used to experimentally determine effective adsorption capacity. When the cumulative adsorption between thermal regeneration steps was maintained below the maximum effective capacity with 0% breakthrough, the zeolite-based adsorbent was found to effectively minimize passive desorption. The impact of regeneration feed conditions, such as inert, oxidizing, humidified air, on thermal desorption was examined. These conditions influenced desorption of the zeolite-based adsorbent but had minimal impact on the ACF felt adsorbent, which would lead to different regeneration schedules and methods for applications in buildings' heating, ventilation, and air conditioning (HVAC) systems.
Development and Characterization of Cementitious Waste Forms for Immobilization of Granular Activated Carbon, Silver Mordenite, and HEPA Filter Media Solid Secondary Waste
At the Department of Energy’s Hanford site, over 53 million gallons of chemically complex and radioactive wastes have been stored in 177 underground tanks. The Hanford Tank Waste Treatment and Immobilization Plant (WTP) is under construction and is designed to treat and immobilize these wastes. During operations of WTP, solid secondary wastes (SSWs) will be generated as a result of waste treatment, vitrification, off-gas management, and supporting process activities. SSW treatment processes and resulting disposal pathways for the final disposition form of the SSW are needed to support direct feed low activity waste (DFLAW) operations and facilitate continued operation of WTP. The SSWs produced through WTP operations are expected to include used process equipment, contaminated tools and instruments, decontamination wastes, high-efficiency particulate air (HEPA) filters, carbon absorption beds (granular activated carbon, GAC), silver mordenite (AgM) and spent ion-exchange resins. These waste streams are planned to be immobilized in a cementitious waste form and disposed of either as stabilized/blended (non-debris) or encapsulated (debris) in a cementitious waste form. Accordingly, cementitious waste forms from these streams were included in the 2017 Integrated Disposal Facility (IDF) Performance Assessment (PA). The input data used to represent these SSW forms in the 2017 IDF PA involved many assumptions and associated uncertainties. This data limitation was due to the lack of material- and site-specific data available for representative SSW materials in cementitious matrices. To verify the assumed values used in the IDF PA and fill this limitation in available data, Washington River Protection Solutions, LLC (WRPS), has initiated a program targeted toward gathering site specific data relevant to Hanford SSW disposal. The work within this report is a continuation of this ongoing program.
Reducing Internal Resistance in Activated Carbon Supercapacitors via Exfoliated Coal-Derived Graphene Additive
Low equivalent series resistance (ESR) is critical for high-rate energy storage devices (e.g., supercapacitors), and graphene is a promising additive for reducing ESR in carbon-based supercapacitor electrodes. However, graphene can be costly and difficult to produce at scale. This study investigates the addition of graphene, produced through electrochemical exfoliation of domestic coal-derived graphite, in activated carbon-based supercapacitors. The coal-derived graphene was incorporated at varying weight loadings and tested in symmetric supercapacitors with aqueous electrolytes. ESR was evaluated using both direct current internal resistance (DCIR) and electrochemical impedance spectroscopy (EIS) measurements. DCIR measurements revealed ESR reductions of ∼34%, ∼18%, and ∼21% at 3, 5, and 10 wt % loadings, respectively, compared to the baseline (0 wt %) of ∼0.54 Ω. These results were further confirmed by EIS measurements. Correspondingly, power density increased by ∼52%, ∼27%, and ∼35% at 3, 5, and 10 wt % loadings relative to the baseline (∼29 kW/kg). Additionally, the electrodes exhibited moderate increases in specific capacitance and energy density, along with stable cycling performance (capacitance retention above 85% after 100,000 cycles) and capacitive behavior (α = 0.95−0.97), suggesting favorable charge transfer kinetics. These findings highlight the potential of exfoliated coal-derived graphene as an effective additive for supercapacitor electrodes.
Novel Remediation of Mercury-Contaminated Sediments Using Manganese Oxide and Activated Carbon Amendments - 20394
Mercury contamination in sediments poses a challenging remediation problem because of its ability to biogeochemically cycle and biomagnify in the food chain as methylmercury from low resident sediment and porewater concentrations. One mitigation approach is to lower the overall rate of net methylmercury production by creating conditions unfavorable for sulfate and iron reduction or methanogenesis, the primary pathways for methylation of inorganic mercury. Manganese oxides and other redox-active amendments are a promising and novel in situ amendment technology aimed at reducing net methylation of mercury though control of redox conditions in mercury-contaminated sediment-water systems. This paper reviews the thermodynamic and kinetic framework for this remediation technology, presents experimental and spectroscopic data illustrating the approach using solid manganese oxides, and discusses potential advantages, disadvantages, and applications. (authors)
System and method for forming activated carbon aerogels and performing 3D printing
Making a carbon aerogel involves 3-D printing an ink to make a printed part, removing the solvent from the printed part, and carbonizing the printed part (with the solvent removed) to make the aerogel. The ink is based on a solution of a resorcinol-formaldehyde resin (RF resin), water, and an organic thickener. Advantageously, the RF resin contains an acid catalyst, which tends to produce carbon aerogels with higher surface areas upon activation than those produced from methods involving an ink composition containing a base catalyzed resin.
Amino acids as performance-controlling additives in carbonation-activated cementitious materials
This article presents an investigation on the application of amino acids to control the CaCO{sub 3} crystallization in carbonation cured wollastonite composites. It was observed that wollastonite carbonated without any amino acid formed calcite as the primary polymorph of CaCO{sub 3}. In contrast, the use of amino acids as admixtures resulted in the formation of stable amorphous calcium carbonate (ACC), vaterite, and aragonite during the carbonation of wollastonite. The carbonated composites produced with amino acids were observed to have a lower critical pore size, but a higher total porosity, compared to the control batch. Additionally, the utilization of amino acids was observed to increase the flexural strength and compressive strength of the composites up to 106% and 48%, respectively, compared to the control batch. Such performance enhancement of the carbonated composites in the presence of amino acids was attributed to the reduced critical pore size and the formation of organic-inorganic hybrid phases in the matrix.
Affinity of LDR Organics to Cementitious Materials and Activated Carbon
The Hanford site stores approximately 56 million gallons of radioactive and hazardous waste in underground storage tanks. The current low-activity waste (LAW) vitrification facility does not have the capacity to immobilize all of the LAW. Therefore, cementitious waste forms are being evaluated as a cost-effective supplemental waste treatment, focusing on the solidification/immobilization of Land Disposal Restricted (LDR) organics, which is currently not recognized by the Environmental Protection Agency (EPA) as a standard treatment method (40 CFR 268.42). Previous efforts by the EPA and waste management agencies have highlighted the potential for cementitious materials to retain certain organic species through physical (encapsulation) and chemical (sorption) interactions.
Highly Active Carbon–Platinum-Based Nanozymes: Synthesis, Characterization, and Immunoassay Application
Nanozymes (nanomaterials with intrinsic enzyme-like characteristics) have gained much attention for diagnostics and therapy due to their excellent enzyme-mimicking capability, great stability in environments, and facile and low-cost production. However, developing nanozymes with a high catalytic constant, K cat , has been challenging. Herein, we report a class of nanozyme-mimicking peroxidases, which are formed by depositing ultrasmall platinum nanoparticles (Pt NPs) 1–2 nm in size on the surface of hydrophilic nitrogen-doped carbon nanoparticles (CN NPs). These nanozymes defined as CN-Pt NPs show a high peroxidase-like activity with K cat values of 1.27 M·mL/s·g for 3,3,5,5′-tetramethylbenzidine (TMB) and 1.97 M·mL/s·g for hydrogen peroxide (H 2 O 2 ), respectively, which are at least one or two orders higher than many other reported carbon–noble metal-based nanozymes. Our developed CN-Pt NPs were further utilized in a colorimetric immunoassay as signal amplifiers for the biomarker detection of Burkholderia pseudomallei, a Gram-negative bacterial pathogen classified as a tier 1 select agent by the US CDC. In conclusion, the assay achieved lower limits of detection of 0.11 ng/mL in phosphate-buffered saline (PBS) and 0.16 ng/mL in human serum, when compared to many other assays in detecting the same biomarker.
Hierarchical Porous Activated Carbon from Wheat Bran Agro-Waste: Applications in Carbon Dioxide Capture, Dye Removal, Oxygen and Hydrogen Evolution Reactions
Here this work reports an efficient method for facile synthesis of hierarchically porous carbon (WB-AC) utilizing wheat bran waste. Obtained carbon showed 2.47 mmol g -1 CO 2 capture capacity with good CO 2 /N 2 selectivity and 27.35 to 29.90 kJ mol -1 isosteric heat of adsorption. Rapid removal of MO dye was observed with a capacity of ~555 mg g -1 . Moreover, WB-AC demonstrated a good OER activity with 0.35 V low overpotential at 5 mA cm -2 and a Tafel slope of 115 mV dec -1 . It also exhibited high electrocatalytic HER activity with 57 mV overpotential at 10 mA cm -2 and a Tafel slope of 82.6 mV dec -1 . The large SSA (757 m 2 g -1 ) and total pore volume (0.3696 cm 3 g -1 ) result from N 2 activation contributing to selective CO 2 uptake, high and rapid dye removal capacity and superior electrochemical activity (OER/HER), suggesting the use of WB-AC as cost effective adsorbent and metal free electrocatalyst.