Search NASA⌕ Search

SEARCH · Search NASA

Results for “actuator disk method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2018

Design of Distributed Mail-Slot Propulsion System on a Hybrid Wingbody Aircraft

This paper deals with designing a thrust distribution strategy when a Turboelectric Distributed Propulsion (TeDP) system of 16 embedded propulsors is installed on an aerodynamically optimized hybrid wing-body configuration. This HWB previously designed to satisfy conditions of trim, longitudinally static stability and specific cargo space is employed as the baseline configuration for the current study of seeking an optimal propulsion/power system. According to the nature of the entrance flow condition for each distributed propulsion passage in hybrid wing-body aircraft, the ingested boundary layer thickness differs and results in different propulsive reaction. An optimal distribution of thrust and power output is determined by how the system utilizes the propulsive characteristics of each passage. The design space and the number of design variables are selected and described accordingly. An actuator disk model is employed to model thrust generation and shaft power from the propulsor. To carry out the optimization of the propulsion/power system on a computationally expensive CFD model, a Kriging method in conjunction with a Genetic Algorithm (GA) is applied. Throughout the design process, the propulsion performances of the sampled propulsion/power system are analyzed and compared to those of a clean flow engine. The performance metrics includes mass flow rate, fan pressure ratio besides the thrust and shaft power. Minimization of total shaft power from the distributed engine is performed at multiple thrust levels. The benefit of boundary layer ingestion propulsion system is quantified via comparison of thrust equivalent, shaft power and mass flow equivalent clean flow engines with CFD based system design.

Hybrid Wingbody↗
NASA NTRS1977

Aerodynamic interference effects on tilting proprotor aircraft

The Green's function method was used to study tilting proprotor aircraft aerodynamics with particular application to the problem of the mutual interference of the wing-fuselage-tail-rotor wake configuration. While the formulation is valid for fully unsteady rotor aerodynamics, attention was directed to steady state aerodynamics, which was achieved by replacing the rotor with the actuator disk approximation. The use of an actuator disk analysis introduced a mathematical singularity into the formulation; this problem was studied and resolved. The pressure distribution, lift, and pitching moment were obtained for an XV-15 wing-fuselage-tail rotor configuration at various flight conditions. For the flight configurations explored, the effects of the rotor wake interference on the XV-15 tilt rotor aircraft yielded a reduction in the total lift and an increase in the nose-down pitching moment. This method provides an analytical capability that is simple to apply and can be used to investigate fuselage-tail rotor wake interference as well as to explore other rotor design problem areas.

Soohoo, P.↗
NASA NTRS1991

Calculating Flow Through A Helicopter Rotor

New method for calculating flow of air through and around helicopter rotor incorporated into General Rotorcraft Aeromechanical Stability Program (GRASP) (computer program for aeroelastic analysis). Flow about helicopter rotor represented by axisymmetric flow field in cylindrical region with actuator disk as source of flow.

Kunz, Donald L.↗
NASA NTRS1995

A guide to the use of the pressure disk rotor model as implemented in INS3D-UP

This is a guide for the use of the pressure disk rotor model that has been placed in the incompressible Navier-Stokes code INS3D-UP. The pressure disk rotor model approximates a helicopter rotor or propeller in a time averaged manner and is intended to simulate the effect of a rotor in forward flight on the fuselage or the effect of a propeller on other aerodynamic components. The model uses a modified actuator disk that allows the pressure jump across the disk to vary with radius and azimuth. The cyclic and collective blade pitch angles needed to achieve a specified thrust coefficient and zero moment about the hub are predicted. The method has been validated with experimentally measured mean induced inflow velocities as well as surface pressures on a generic fuselage. Overset grids, sometimes referred to as Chimera grids, are used to simplify the grid generation process. The pressure disk model is applied to a cylindrical grid which is embedded in the grid or grids used for the rest of the configuration. This document will outline the development of the method, and present input and results for a sample case.

Chaffin, Mark S.↗
NASA NTRS1985

Vibration control of rotor shaft

Suppression of flexural forced vibration or the self-excited vibration of a rotating shaft system not by passive elements but by active elements is described. The distinctive feature of this method is not to dissipate the vibration energy but to provide the force cancelling the vibration displacement and the vibration velocity through the bearing housing in rotation. Therefore the bearings of this kind are appropriately named Active Control Bearings. A simple rotor system having one disk at the center of the span on flexible supports is investigated in this paper. The actuators of the electrodynamic transducer are inserted in the sections of the bearing housing. First, applying the optimal regulator of optimal control theory, the flexural vibration control of the rotating shaft and the vibration control of support systems are performed by the optimal state feedback system using these actuators. Next, the quasi-modal control based on a modal analysis is applied to this rotor system. This quasi-modal control system is constructed by means of optimal velocity feedback loops. The differences between optimal control and quasi-modal control are discussed and their merits and demerits are made clear. Finally, the experiments are described concerning only the optimal regulator method.

Nonami, K.↗
NASA NTRS1984

Flow prediction for propfan configurations using Euler equations

An Euler code has been developed for the analysis of a wing-mounted propfan configuration. Surface-fitted grids are used to represent the wing, fuselage, and nacelle geometry. The propeller is simulated by an actuator disk along a computational plane. A grid embedding technique is employed to capture detailed flow field resolution in the vicinity of the engine exhaust plume. Results of a NASA turboprop configuration are compared with test data. Specific issues on grid embedding and methods of resolving them are discussed.

Yu, N. J.↗
NASA NTRS1991

Navier-Stokes computation of wing/rotor interaction for a tilt rotor in hover

A method has been developed to analyze the wing/rotor interaction of tilt rotor aircraft in hover. The unsteady, thin-layer compressible Navier-Stokes equations are solved using an implicit, finite difference scheme that employs LU-ADI factorization. The rotor is modeled as an actuator disk which imparts a radial and azimuthal distribution of pressure rise and swirl to the flowfield. The 'chimera' approach of grid point blanking is used to update the rotor boundary conditions. Results are presented for both a rotor alone and for wing/rotor interaction where the thrust coefficient is 0.0164 and wing flap deflection is 67 degrees. Many of the complex flow features are captured including the fountain effect, leading and trailing edge separation, and the unsteady wake beneath the wing. Wing surface pressures compare fairly well with experimental data although the time-averaged download is about twenty percent higher than the measured value. This discrepancy is due to a combination of factors that are discussed.

Fejtek, Ian↗
NASA NTRS2007

NASA Tech Briefs, December 2007

Topics include: Ka-Band TWT High-Efficiency Power Combiner for High-Rate Data Transmission; Reusable, Extensible High-Level Data-Distribution Concept; Processing Satellite Imagery To Detect Waste Tire Piles; Monitoring by Use of Clusters of Sensor-Data Vectors; Circuit and Method for Communication Over DC Power Line; Switched Band-Pass Filters for Adaptive Transceivers; Noncoherent DTTLs for Symbol Synchronization; High-Voltage Power Supply With Fast Rise and Fall Times; Waveguide Calibrator for Multi-Element Probe Calibration; Four-Way Ka-Band Power Combiner; Loss-of-Control-Inhibitor Systems for Aircraft; Improved Underwater Excitation-Emission Matrix Fluorometer; Metrology Camera System Using Two-Color Interferometry; Design and Fabrication of High-Efficiency CMOS/CCD Imagers; Foam Core Shielding for Spacecraft CHEM-Based Self-Deploying Planetary Storage Tanks Sequestration of Single-Walled Carbon Nanotubes in a Polymer PPC750 Performance Monitor Application-Program-Installer Builder Using Visual Odometry to Estimate Position and Attitude Design and Data Management System Simple, Script-Based Science Processing Archive Automated Rocket Propulsion Test Management Online Remote Sensing Interface Fusing Image Data for Calculating Position of an Object Implementation of a Point Algorithm for Real-Time Convex Optimization Handling Input and Output for COAMPS Modeling and Grid Generation of Iced Airfoils Automated Identification of Nucleotide Sequences Balloon Design Software Rocket Science 101 Interactive Educational Program Creep Forming of Carbon-Reinforced Ceramic-Matrix Composites Dog-Bone Horns for Piezoelectric Ultrasonic/Sonic Actuators Benchtop Detection of Proteins Recombinant Collagenlike Proteins Remote Sensing of Parasitic Nematodes in Plants Direct Coupling From WGM Resonator Disks to Photodetectors Using Digital Radiography To Image Liquid Nitrogen in Voids Multiple-Parameter, Low-False-Alarm Fire-Detection Systems Mosaic-Detector-Based Fluorescence Spectral Imager Plasmoid Thruster for High Specific-Impulse Propulsion Analysis Method for Quantifying Vehicle Design Goals Improved Tracking of Targets by Cameras on a Mars Rover Sample Caching Subsystem Multistage Passive Cooler for Spaceborne Instruments GVIPS Models and Software Stowable Energy-Absorbing Rocker-Bogie Suspensions

Source record↗
NASA NTRS1985

Unsteady Flow in Multistage Turbines

The development of an efficient model for the response of a multistage turbine to either a total pressure or total temperature distortion is discussed. Each turbine blade row is modeled as an actuator disk and is often used to describe the flow through turbine and compressor blade rows. The flow approaching the blade row is assumed to be subsonic and inviscid. The distortion occurs at upstream infinity and is in the form of total pressure or total temperature. A solution was found to unsteady Euler equations by using a finite volume method. With prescribed inlet and boundary conditions flow variables such as density, pressure, and velocities can be calculated at cell centers in the entire flow region. The inlet and exit of the blade row coincide with lines of constant.

Surampudi, S. P.↗
NASA NTRS2018

Aerodynamic Design and Optimization of Fan Stage for Boundary Layer Ingestion Propulsion System

The present paper addresses the process of preliminary design of a low-pressure fan and outlet guide vane (OGV) of a boundary layer ingestion (BLI) propulsion system. The tail-cone thruster systems of NASA's STARC_ABL (Single-aisle Turboelectric Aircraft with an Aft Boundary-Layer propulsor) adopts an axi-symmetric BLI type inlet as opposed to other embedded engine systems. Thus, the focus of the present work is placed on maximizing the efficiency of the fan and OGV stages under a significant radial distortion. A parameterization with B-spline function for camber line angles, metal chord, thickness distribution and stacking axis of blades is presented. The flowpath lines are also parameterized by B-spline function and aggregated in the design system of blades. The design optimization with evolutionary algorithm is performed with constraints of fan pressure ratio, OGV exit swirl angle and nozzle exit properties. The inlet conditions for the turbo-machinery CFD (Computational Fluid Dynamics) domain and the design goal of the fan stage are driven by a propulsion airframe integration (PAI) model that uses a 3-D unstructured RANS (Reynolds Average Navier Stokes) solver and actuator disk model. The expected power saving of the BLI propulsor is quantified via PAI analysis and the resulting preliminary design of the fan stages is compared with a clean-inlet flow propulsor.

Turbo-machinery↗
DOE OSTI2025

An airfoil-based synthetic actuator disk model for wind turbine aerodynamic and structural analysis

Here, this study introduces an airfoil-based refinement technique to enhance the Actuator Disk Model (ADM) for improved wind turbine aerodynamic load prediction and structural simulation in conjunction with Large Eddy Simulations of the wind flow. While ADM offers higher computational efficiency than the more detailed but resource-intensive Actuator Line Model (ALM), it traditionally lacks the resolution needed to capture the localized blade forces accurately. To address this limitation, we introduce a refinement technique that uses airfoil-specific data and employs interpolation-based grid point refinement, achieving ALM-comparable accuracy while preserving ADM's efficiency. Unlike conventional ADM that provides only rotor-disk averaged forces, our synthetic method tracks transient aerodynamic load variations over multiple blade revolutions, allowing us to calculate the distributions of maximum and minimum loads during typical cycles. Applied to the NREL 5 MW reference turbine, our enhanced ADM accurately predicts key aerodynamic parameters (angle of attack, axial velocity, lift, drag, axial and tangential forces along the blades) as well as structural responses (blade tip deflection, maximum stress, and stress concentration). Our results show that the tip deflection ranges from 2.33m (3.69 % of blade length) to 4.28m (6.79 %), with maximum stress concentration occurring near the blade root. This research demonstrates that a refined synthetic ADM approach can serve as a computationally efficient alternative for both aerodynamic analysis and structural simulation of wind turbine blades subjected to realistic wind fields.

17 WIND ENERGY↗
NASA NTRS1986

Flow prediction for propfan engine installation effects on transport aircraft at transonic speeds

An Euler-based method for aerodynamic analysis of turboprop transport aircraft at transonic speeds has been developed. In this method, inviscid Euler equations are solved over surface-fitted grids constructed about aircraft configurations. Propeller effects are simulated by specifying sources of momentum and energy on an actuator disc located in place of the propeller. A stripwise boundary layer procedure is included to account for the viscous effects. A preliminary version of an approach to embed the exhaust plume within the global Euler solution has also been developed for more accurate treatment of the exhaust flow. The resulting system of programs is capable of handling wing-body-nacelle-propeller configurations. The propeller disks may be tractors or pushers and may represent single or counterrotation propellers. Results from analyses of three test cases of interest (a wing alone, a wing-body-nacelle model, and a wing-nacelle-endplate model) are presented. A user's manual for executing the system of computer programs with formats of various input files, sample job decks, and sample input files is provided in appendices.

Samant, S. S.↗
NASA NTRS1975

Optimum performance and potential flow field of hovering rotors

Rotor and propeller performance and induced potential flowfields were studied on the basis of a rotating actuator disk concept, with special emphasis on rotors hovering out of ground effect. A new theory for the optimum performance of rotors hovering OGE is developed and presented. An extended theory for the optimum performance of rotors and propellers in axial motion is also presented. Numerical results are presented for the optimum distributions of blade-bound circulation together with axial inflow and ultimate wake velocities for the hovering rotor over the range of thrust coefficient of interest in rotorcraft applications. Shapes of the stream tubes and of the velocities in the slipstream are obtained, using available methods, for optimum and off-optimum circulation distributions for rotors hovering in and out of ground effect. A number of explicit formulae useful in computing rotor and propeller induced flows are presented for stream functions and velocities due to distributions of circular vortices over axi-symmetric surfaces.

Wu, J. C.↗
NASA NTRSDate not supplied

Evaluation of VSPAERO Analysis Capabilities for Conceptual Design of Aircraft with Propeller-Blown Wings

Advancements in electric propulsion and the emergence of Advanced Air Mobility are driving the evolution of new aircraft designs. Since electric propulsion enables flexibility in propeller location, there is an increasing need for reliable, quick analyses of propeller-airframe interactions during the conceptual design phase. Many existing analysis tools capable of accurately modeling propeller-airframe interactions are computationally expensive and require a high level of expertise and significant time investment for setup. VSPAERO is a NASA-developed, open source, computational analysis tool that runs a Vortex-Lattice Method (VLM) solver and is targeted at conceptual design. This paper assesses the applicability of the VSPAERO VLM in the conceptual design phase by comparing VSPAERO predictions to predictions by OVERFLOW, a Reynolds-Averaged Navier-Stokes Computational Fluid Dynamics solver, and RoBIN, another VLM tool. The paper details the modeling, meshing, and analysis techniques used within VSPAERO. Analyses were performed for a wing in isolation, a propeller in isolation, and then for two propeller-blown wing configurations: one with a propeller located at the midspan and another with a propeller located at the wingtip. The propeller was modeled both as an actuator disk and as rotating blades.

VSPAERO↗
DOE OSTI2020

Assessing the blockage effect of wind turbines and wind farms using an analytical vortex model

Wind farm blockage effects are currently neglected in the prediction of wind farm energy yield, typically leading to an overestimation of the production. This work presents a novel method to assess wind farm production, while accounting for blockage effects. We apply a vortex model, based on a cylindrical wake, to assess induction effects. We present variations of the model to account for finite wake length, finite tip-speed ratios, and the proximity to the ground. The results are applied to single rotors in aligned and yawed conditions and to different wind farm layouts. We provide far-field approximations for faster estimates of the velocity field. Further, this article includes a new methodology to couple the induction model to engineering wake models, such as the ones present in the FLOw Redirection and Induction in Steady State (FLORIS). We compare the results to actuator disk simulations for various operating conditions of a single turbine and different wind farm layouts. We found that the mean relative error of the model in the induction zone is typically around 0.2% compared with actuator disk simulations. The computational time of the velocity field using the analytical vortex model is three orders of magnitude less than the one obtained with the actuator disk simulation.

17 WIND ENERGY↗
NASA NTRS2022

AST Critical Propulsion and Noise Reduction Technologies for Future Commercial Subsonic Engines Aeroacoustic Prediction Codes - Supplement: Code Descriptions and Users Guides

This report describes work performed on Contract NAS3–27720 AoI 13 as part of the NASA Advanced Subsonic Transport (AST) Noise Reduction Technology effort. Computer codes were developed to provide quantitative prediction, design, and analysis capability for several aircraft engine noise sources. The objective was to provide improved, physics-based tools for the exploration of noise-reduction concepts and the understanding of experimental results. Methods and codes focused on fan broadband and “buzz saw” noise and on low-emissions combustor noise and complement work done by other contractors under the NASA AST program to develop methods and codes for fan harmonic tone noise and jet noise. The methods and codes developed and reported herein employ a wide range of approaches, from the strictly empirical to the completely computational, with some being semiempirical, analytical, and/or analytical/computational. Emphasis was on capturing the essential physics while still considering method or code utility as a practical design and analysis tool for everyday engineering use. Codes and prediction models were developed for: (1) an improved empirical correlation model for fan rotor exit flow mean and turbulence properties, for use in predicting broadband noise generated by rotor exit flow turbulence interaction with downstream stator vanes; (2) fan broadband noise models for rotor and stator/turbulence interaction sources including 3D effects, noncompact-source effects, directivity modeling, and extensions to the rotor supersonic tip-speed regime; (3) fan multiple-pure-tone in-duct sound pressure prediction methodology based on CFD analysis; and (4) low-emissions combustor prediction methodology and computer code based on CFD and actuator disk theory. In addition, the relative importance of dipole and quadrupole source mechanisms was studied using direct CFD source computation for a simple cascade/gust interaction problem, and an empirical combustor-noise correlation model was developed from engine acoustic test results. This work provided several insights on potential approaches to reducing aircraft engine noise. Code development is described in Volume I, and those insights are discussed. Volume II documents the computer codes developed and gives instructions on how to use them.

Philip Gliebe↗
NASA NTRS2003

Active Blade Vibration Control Being Developed and Tested

Gas turbine engines are currently being designed to have increased performance, lower weight and manufacturing costs, and higher reliability. Consequently, turbomachinery components, such as turbine and compressor blades, have designs that are susceptible to new vibration problems and eventual in-service failure due to high-cycle fatigue. To address this problem, researchers at the NASA Glenn Research Center are developing and testing innovative active blade vibration control concepts. Preliminary results of using an active blade vibration control system, involving a rotor supported by an active magnetic bearing in Glenn's Dynamic Spin Rig, indicate promising results (see the photograph). Active blade vibration control was achieved using feedback of blade strain gauge signals within the magnetic bearing control loop. The vibration amplitude was reduced substantially (see the graphs). Also, vibration amplitude amplification was demonstrated; this could be used to enhance structural mode identification, if desired. These results were for a nonrotating two-bladed disk. Tests for rotating blades are planned. Current and future active blade vibration control research is planned to use a fully magnetically suspended rotor and smart materials. For the fully magnetically suspended rotor work, three magnetic bearings (two radial and one axial) will be used as actuators instead of one magnetic bearing. This will allow additional degrees of freedom to be used for control. For the smart materials work, control effectors located on and off the blade will be considered. Piezoelectric materials will be considered for on-the-blade actuation, and actuator placement on a stator vane, or other nearby structure, will be investigated for off-the-blade actuation. Initial work will focus on determining the feasibility of these methods by performing basic analysis and simple experiments involving feedback control.

Johnson, Dexter↗
DOE OSTI2021

Quantifying wind plant blockage under stable atmospheric conditions

Wind plant blockage reduces the wind velocity upstream undermining turbine performance for the first row of the plant. We assess how atmospheric stability modifies the induction zone of a wind plant in flat terrain. We also explore different approaches to quantifying the magnitude and extent of the induction zone from field-like observations. To investigate the influence from atmospheric stability, we compare simulations of two stable boundary layers using the Weather Research and Forecasting model in large-eddy simulation mode, representing wind turbines using the generalized actuator disk approach. We find a faster cooling rate at the surface, which produces a stronger stably stratified boundary layer, amplifies the induction zone of both an isolated turbine and of a large wind plant. A statistical analysis on the hub-height wind speed field shows wind slowdowns only extend far upstream (up to 15D) of a wind plant in strong stable boundary layers. To evaluate different ways of measuring wind plant blockage from field-like observations, we consider various ways of estimating the freestream velocity upstream of the plant. Sampling a large area upstream is the most accurate approach to estimating the freestream conditions, and thus of measuring the blockage effect. Also, the choice of sampling method may induce errors of the same order as the velocity deficit in the induction zone.

54 ENVIRONMENTAL SCIENCES↗