Search NASA⌕ Search

SEARCH · Search NASA

Results for “adjust”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1950

Analytical investigation of turbines with adjustable stator blades and effect of these turbines on jet-engine performance

Adjustable-stator turbines are applied to turbojet engines and probable performance is compared with conventional engines with and without variable-area exhaust nozzles. Variation in stator-exit angle and exhaust area was not excessive for wide ranges of engine output. Variation in turbine efficiency for contemporary turbines equipped with adjustable stators was small. Improvements from 4.5 to 17 percent in over-all engine specific fuel consumption over conventional engines and from 2 to 8.5 percent over engines equipped with only adjustable-area exhaust nozzles were obtained at 60-percent rated power with adjustable-stator turbines and variable-area exhaust nozzles. The improvements depend on design parameters.

ENGINE TYPES, COMPARISON↗
NASA NTRS2001

Adjustable Autonomy Testbed

The Adjustable Autonomy Testbed (AAT) is a simulation-based testbed located in the Intelligent Systems Laboratory in the Automation, Robotics and Simulation Division at NASA Johnson Space Center. The purpose of the testbed is to support evaluation and validation of prototypes of adjustable autonomous agent software for control and fault management for complex systems. The AA T project has developed prototype adjustable autonomous agent software and human interfaces for cooperative fault management. This software builds on current autonomous agent technology by altering the architecture, components and interfaces for effective teamwork between autonomous systems and human experts. Autonomous agents include a planner, flexible executive, low level control and deductive model-based fault isolation. Adjustable autonomy is intended to increase the flexibility and effectiveness of fault management with an autonomous system. The test domain for this work is control of advanced life support systems for habitats for planetary exploration. The CONFIG hybrid discrete event simulation environment provides flexible and dynamically reconfigurable models of the behavior of components and fluids in the life support systems. Both discrete event and continuous (discrete time) simulation are supported, and flows and pressures are computed globally. This provides fast dynamic simulations of interacting hardware systems in closed loops that can be reconfigured during operations scenarios, producing complex cascading effects of operations and failures. Current object-oriented model libraries support modeling of fluid systems, and models have been developed of physico-chemical and biological subsystems for processing advanced life support gases. In FY01, water recovery system models will be developed.

Malin, Jane T.↗
NASA NTRS2001

Architectures and Evaluation for Adjustable Control Autonomy for Space-Based Life Support Systems

In the past five years, a number of automation applications for control of crew life support systems have been developed and evaluated in the Adjustable Autonomy Testbed at NASA's Johnson Space Center. This paper surveys progress on an adjustable autonomous control architecture for situations where software and human operators work together to manage anomalies and other system problems. When problems occur, the level of control autonomy can be adjusted, so that operators and software agents can work together on diagnosis and recovery. In 1997 adjustable autonomy software was developed to manage gas transfer and storage in a closed life support test. Four crewmembers lived and worked in a chamber for 91 days, with both air and water recycling. CO2 was converted to O2 by gas processing systems and wheat crops. With the automation software, significantly fewer hours were spent monitoring operations. System-level validation testing of the software by interactive hybrid simulation revealed problems both in software requirements and implementation. Since that time, we have been developing multi-agent approaches for automation software and human operators, to cooperatively control systems and manage problems. Each new capability has been tested and demonstrated in realistic dynamic anomaly scenarios, using the hybrid simulation tool.

Malin, Jane T.↗
NASA NTRS2018

Adjustments and Uncertainty Quantification for SLS Aerodynamic Sectional Loads

This paper presents a method for adjusting sectional loads to match target values for integrated force and moment coefficients. In a typical application, the sectional load profile for one flight condition is calculated from Computational Fluid Dynamics (CFD) while the integrated forces and moments are measured in a wind tunnel experiment. These two methods do not generally result in identical predictions, and this leads to an inherent inconsistency between different data products. This paper aims to provide a procedure to remove that inconsistency. A sectional load profile for a launch vehicle splits the rocket into slices along its length and calculates the aerodynamic loading on each slice, which leads to a one-dimensional aerodynamic load profile that is used for structural analysis. Adjusting sectional loads, also known as line loads, is a nontrivial matter due to several consistency constraints. For example, the adjusted sectional normal force profile must be consistent with both the integrated normal force and pitching moment. To avoid such inconsistency issues, this paper presents a method using a Proper Orthogonal Decomposition (POD) to generate basis functions to adjust the sectional load profiles. As a corollary, this correction method enables the creation of an uncertainty quantification for sectional loads that is consistent with the dispersed integrated force and moment database and its uncertainty quantification. Several extensions to this technique, such as applying the method to the surface pressures, are considered.

Quantification↗
NASA NTRSDate not supplied

High resolution assimilation of multiple satellite retrievals with emissions adjustment to improve air quality forecasting with WRF-Chem/DART

We will present results from medium (15km, 6hr cycling) and high (4 km, 6 hr cycling) spatiotemporal resolution applications of the WRF-Chem/DART ensemble, regional, air quality (AQ) forecast/assimilation system.The medium-resolution setup is applied to the Discover AQ/Front Range Air Pollution and Photochemistry Experiment (FRAPPE) domain from July 14 to July 29, 2014. The high-resolution setup is applied to a Colorado domain from July 14 to July 29, 2020. For the FRAPPE application, we assimilate MOPITT CO; IASI CO;MODIS AOD; OMI O3, NO2; and AirNow CO, O3, NO2, SO2, PM10, and PM2.5. For the Colorado application, we assimilate the same MOPITT, MODIS, and AirNow constituents as in the FRAPPE application and TROPOMI CO, O3, NO2; and synthetic TEMPO O3and NO2. WRF-Chem/DART integrates the Weather Research and Forecast (WRF) model with on-line chemistry (WRF-Chem) into the Data Assimilation Research Testbed (DART). It assimilates AirNow CO, O3, NO2, SO2, PM10, and PM2.5 measurements, MOPITT CO; IASI CO, O3; OMI O3, NO2, SO2; TROPOMI CO, O3, NO2, SO2; MODIS AOD; and synthetic TEMPO O3 and NO2 total/partial column and/or profile retrievals.WRF-Chem/DART uses: (i) the state augmentation method for adjusting emissions; (ii) state-space localization; and (iii) a near-real time scripting system. We use the medium-resolution FRAPPE application to demonstrate the incremental benefits from assimilating OMI observations with emissions adjustment and the high-resolution Colorado application to demonstrate the incremental benefits from assimilating syntheticTEMPO observations with emissions adjustment. For both applications, we expect that: (i) assimilating chemical observations will increaseAQ forecast skill; (ii) including emissions adjustment will increase forecast skill/predictability; and (iii) including assimilation of synthetic TEMPO observations will further increase forecast skill/predictability.

High resolution↗
NASA NTRS1966

Mount enables precision adjustment of optical-instrumentation mirror

Mirror mount assembly allows the plane of a mirror to be adjusted through small angles about two orthogonal axes. The assembly, which has a mirror mount with two independently adjustable flexure joints, allows independent precise adjustment of the mirror mount with respect to each axis.

Source record↗
NASA NTRS1975

Sequential and simultaneous SLAR block adjustment

Two sequential methods of planimetric SLAR (Side Looking Airborne Radar) block adjustment, with and without splines, and three simultaneous methods based on the principles of least squares are evaluated. A limited experiment with simulated SLAR images indicates that sequential block formation with splines followed by external interpolative adjustment is superior to the simultaneous methods such as planimetric block adjustment with similarity transformations. The use of the sequential block formation is recommended, since it represents an inexpensive tool for satisfactory point determination from SLAR images.

Leberl, F.↗
NASA NTRS1984

A calibration adjustment technique combining ERB parameters from different remote sensing platforms into a long-term data set

Earth-radiation-budget (ERB) experiments on board the Nimbus-6 (ERB 6) and Nimbus-7 (ERB 7) spacecraft have measured wide-field-of-view total (0.2 to 50 micron), shortwave (0.2 to 3.8 micron), and near-infrared (0.7 to 2.8 micron) terrestrial irradiances for a joint lifetime of over 8 years. Though the spectral characteristics of both experiments are nearly identical, instrument degradation and altitude differences introduce discrepancies between the two data sets. ERB parameters from these two observing platforms may be combined into a scientifically meaningful data set only after these discrepancies are eliminated. To facilitate the creation of a long-term ERB data set, comparisons of the ERB 6 experiment irradiances with, and calibration adjustments with respect to, the corresponding ERB 7 irradiances have been performed. Two calibration methods were developed and applied to the irradiance data from 28 pairs of collocated orbits. The differential effects of altitude, illumination, albedo, and scene inhomogeneities were applied. The result is a set of calibration adjustments that adjust the ERB 6 data to match the ERB 7 data.

Ardanuy, P. E.↗
NASA NTRS1986

Smoothly Adjustable dc Load

Load circuit for testing dc power supplies adjusted without momentary interruptions typical of rheostat loads. Load current passes through power transistor and fixed resistor instead of wire-wound rheostat. In new circuit potentiometer used to adjust bias of power transistor and thereby adjust load. Components are standard, commercially available parts, mounted on transistor heat sink, forming compact package.

Patocka, C. G.↗
NASA NTRS1985

Three-dimensional adjustment of trilateration data

The three-dimensional locations of the monuments in the USGS Hollister trilateration network were adjusted to fit line length observations observed in 1977, using a Bayesian approach, and incorporating prior elevation estimates as data in the adjustment procedure. No significant discrepancies in the measured line lengths were found, but significant elevation adjustments (up to 1.85 m) were needed to fit the length data.

Sung, L.-Y.↗
NASA NTRS1985

A new convective adjustment scheme

A marked divergence in philosophy is presented. The primary objective of the proposed parameterization scheme is to ensure that the local vertical temperature and moisture structures, which in nature are strongly constrained by convection, be realistic in the large scale model. The concept of a quasi-equilibrium between the cloud field and the large-scale forcing has been well established. This means that convective regions have characteristic temperature and moisture structures that can be documented observationally and used as the basis of a convective adjustment procedure. In the scheme proposed here, the temperature and moisture structures will be adjusted simultaneously toward observed quasi-equilibrium structures. This ensures that on the grid scale a global model always maintains a realistic vertical temperature and moisture structure in the presence of convection. The saturation point formulation of moist thermodynamics will be used to introduce the observational and theoretical basis of the proposed convective adjustment. The scheme is then applied to a series of data sets from GATE, BOMEX, ATEX and an Arctic air-mass transformation to show the sensitivity of the scheme to different parameters and develop a parameter set suitable for both shallow and deep convection in a global model.

Betts, A. K.↗
NASA NTRS1986

On crossover adjustment in satellite altimetry and its oceanographic implications

It is argued that, to remove the satellite orbital errors, the crossover adjustment method that represents orbital errors in terms of Fourier series is preferable to the conventional bias-and-tilt crossover adjustment method. However, no matter what technique is used in the crossover adjustment, orbital errors will introduce a geographically dependent error (mostly a large-scale slope, which, in terms of spherical harmonics, is represented by the degree 1 terms) into the derived sea surface topography. This is because the responsible orbital errors have left no traces in crossover differences and therefore can never be removed. However, it is possible to reduce this fundamental uncertainty substantially if the record length is long enough; its implications on observing the basin-scale ocean circulation by satellite altimetry are discussed. New methods for observing the large-scale oceanic variability are also proposed (the conventional approach being limited to observing the mesoscale variability).

Tai, C.-K.↗
NASA NTRS1988

The dangers of underestimating the importance of data adjustments in band ratioing

The practical importance of simple data adjustments for path (atmospheric) radiance and sensor calibration offsets prior to band ratioing has often been overlooked or misjudged. This paper describes and demonstrates the critical nature of data adjustments for the production of useful ratio images, including ratio images derived solely from long wavelength bands. A simple bispectral graphic model is used for illustrating and evaluating the impact of data offsets upon ratio images. Orthogonal indices, used as alternatives to band ratios, are shown to be sometimes less sensitive to topographic influences than ratios of unadjusted data but not less sensitive than ratios of properly adjusted data.

Crippen, Robert E.↗
NASA NTRS1990

Inverse dynamics of adaptive space cranes with tip point adjustment

The 'space crane', which resembles a conventional solid-link robot but employs truss sections in place of links and length-adjustable bars in place of torque-generating motors, is presently characterized by means of two different inverse-dynamics schemes. While in the first of these the nominal angles are maintained between the links constituting the crane, the second scheme adjusts the nominal angles as a function of time in order to always maintain the tip of the crane along the desired (nomical) trajectory. Attention is given to the second scheme, and to a tip-adjustment method which keeps the high frequency flexibility vibration within limits and ensures numerical stability.

Das, S. K.↗
NASA NTRS1993

Adjustable-Torque Truss-Joint Mechanism

Threaded pin tightened or loosened; tedious trial-and-error procedure shortened. Mechanism joining strut and node in truss structure preloaded to desired stress to ensure tight, compressive fit preventing motion of strut during loading or vibration. Preload stress on stack of Belleville spring washers adjusted by tightening or loosening threaded Belleville-washer-alignment pin. Pin turned, by use of allen wrench, to adjust compression preload on Belleville washers and adjusts joint-operating torque.

Bush, Harold G.↗
NASA NTRS1994

Adjustable reed for weaving net-shaped tailored fabrics

The invention is an apparatus and method for forming woven fabrics through the use of an adjustable reed. The adjustable reed has multiple groups of reed wires that guide the warp yarns. The groups of reed wires move on reed rails parallel to the warp direction. In addition, rail expanders permit the space between the reed wires to be modified and telescoping rods attached to the rail sliders can be turned to permit the reed wires to be skewed to alter the fill yarn angle. These adjustments to the reed permit simultaneous variation of fill yarn angles and fabric widths and allow these variations to be made during fabrication, without the need to halt production.

Farley, Gary L.↗
NASA NTRS1995

Mechanism For Adjustment Of Commutation Of Brushless Motor

Mechanism enables adjustment of angular position of set of Hall-effect devices that sense instantaneous shaft angle of brushless dc motor. Outputs of sensors fed to commutation circuitry. Measurement of shaft angle essential for commutation; that is, application of voltage to stator windings must be synchronized with shaft angle. To obtain correct angle measurement for commutation, Hall-effect angle sensors positioned at proper reference angle. The present mechanism accelerates adjustment procedure and makes it possible to obtain more accurate indication of minimum-current position because it provides for adjustment while motor running.

Schaefer, Richard E.↗
NASA NTRS2005

Modeling of Turbulent Boundary Layer Surface Pressure Fluctuation Auto and Cross Spectra - Verification and Adjustments Based on TU-144LL Data

The literature on turbulent boundary layer pressure fluctuations provides several empirical models which were compared to the measured TU-144 data. The Efimtsov model showed the best agreement. Adjustments were made to improve its agreement further, consisting of the addition of a broad band peak in the mid frequencies, and a minor modification to the high frequency rolloff. The adjusted Efimtsov predicted and measured results are compared for both subsonic and supersonic flight conditions. Measurements in the forward and middle portions of the fuselage have better agreement with the model than those from the aft portion. For High Speed Civil Transport supersonic cruise, interior levels predicted by use of this model are expected to increase by 1-3 dB due to the adjustments to the Efimtsov model. The space-time cross-correlations and cross-spectra of the fluctuating surface pressure were also investigated. This analysis is an important ingredient in structural acoustic models of aircraft interior noise. Once again the measured data were compared to the predicted levels from the Efimtsov model.

Rackl, Robert↗