Search NASA⌕ Search

SEARCH · Search NASA

Results for “anisotropic stresses”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Complex Fluid‐Driven Fractures Caused by Crack‐Parallel Stress

Abstract Managing fluid‐driven fracture networks is crucial for subsurface resource utilization, yet the current understanding of the key controlling factors remains insufficient. While geologic discontinuities have been shown to significantly influence fracture network complexity, this study identifies another major contributor. We conducted a new set of experiments using a transparent true triaxial cell, which enabled video recording of the temporal evolution of fluid‐driven fracture paths. Using pseudo‐2D samples without macroscale structural discontinuities, we observed multiple occurrences of hydraulic fracture curving and branching under anisotropic boundary stresses. We proposed a theoretical model demonstrating that the stress parallel to the crack line in the solid matrix near the crack tip (i.e., the T ‐stress) accounts for the observed fracture curving behavior. This finding suggests that T ‐stress is an additional mechanism contributing to the complexity of fluid‐driven fracture networks in the subsurface, besides the geologic discontinuities.

58 GEOSCIENCES↗
DOE OSTI2021

CFD analysis of a solid pin-fueled small modular fluoride salt-cooled reactor

A computational fluid dynamics (CFD) study is performed for the pre-conceptual solid pin-fueled small modular fluoride salt-cooled reactor developed by the Oak Ridge National Laboratory (ORNL). The solid and fluid regions in a 1/12th section of a fuel assembly are modeled. The solid region includes fuel and non-fuel pins, with heat generation in the active region of the fuel pins. Two different power profiles, uniform and center-peaked, are considered. The FLiBe coolant flows from the bottom to the top of the core, parallel to the bank of fuel and non-fuel pins. The k-ω shear-stress transport (SST) model is chosen as the baseline turbulence model. The effects of grid refinement, inlet turbulence specification, and turbulence models on the temperature and pressure drop predictions are studied. Turbulence model sensitivity is investigated by comparing the results from the k-ω SST model with other two-equation models (k-ω baseline or BSL and k-ε realizable) as well as with anisotropic Reynolds stress transport models (linear pressure-strain and stress-BSL). Here the results show that the choice of turbulence model has a significant impact on the pin temperature and bundle pressure drop predictions. The results from the baseline turbulence model show good agreement between the fuel pin temperatures and bundle pressure drop values predicted using a subchannel model previously developed by the authors of the present study.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

A Poromechanical Framework for Internal Interactions Induced by Solid Inclusions

The framework of poromechanics is generalized to simulate the multiscale behavior of porous media subjected to internal loadings stemming from the growth of solid inclusions. This generalization is designed to enable the study of anisotropic internal stress generation from solid growth within the pores, while recovering isotropic fluid-induced loading as a particular case. For this purpose, a mathematical strategy to define constitutive tensors in a thermodynamically consistent form is proposed, thus offering new opportunities for determining the poromechanical properties of a porous solid through advanced experimentation or micromechanical models. The framework is specialized by means of established elastic solutions for single pore–matrix interaction, as well as through homogenization schemes considering the interaction among congruent pores. In particular, the second Eshelby solution and the Tanaka–Mori–Benveniste homogenization scheme are used to derive a microporoelastic model. At an elemental scale, the model is tested under mixed control conditions by replicating different scenarios of geomaterial testing. In addition, the model characteristics are outlined with reference to inelastic microscopic loadings replicating chemo-mechanical forcing, such as expansive crystal formation. Through a series of parametric analyses, it is shown that the microstructure of the pores significantly influences the properties of porous media. Most notably, it is shown that the effects of a solid forming within the pores depend in a highly nonlinear fashion on the constitutive characteristics of the inhomogeneities and can therefore not be readily quantified or predicted without models capturing the diverse multiscale interactions among pores, inhomogeneities, and matrix.

chemomechanics↗
DOE OSTI2020

Fluctuation dynamo in a weakly collisional plasma

The turbulent amplification of cosmic magnetic fields depends upon the material properties of the host plasma. In many hot, dilute astrophysical systems, such as the intracluster medium (ICM) of galaxy clusters, the rarity of particle–particle collisions allows departures from local thermodynamic equilibrium. These departures – pressure anisotropies – exert anisotropic viscous stresses on the plasma motions that inhibit their ability to stretch magnetic-field lines. We present an extensive numerical study of the fluctuation dynamo in a weakly collisional plasma using magnetohydrodynamic (MHD) equations endowed with a field-parallel viscous (Braginskii) stress. When the stress is limited to values consistent with a pressure anisotropy regulated by firehose and mirror instabilities, the Braginskii-MHD dynamo largely resembles its MHD counterpart, particularly when the magnetic field is dynamically weak. If instead the parallel viscous stress is left unabated – a situation relevant to recent kinetic simulations of the fluctuation dynamo and, we argue, to the early stages of the dynamo in a magnetized ICM – the dynamo changes its character, amplifying the magnetic field while exhibiting many characteristics reminiscent of the saturated state of the large-Prandtl-number ( ${Pm}\gtrsim {1}$ ) MHD dynamo. We construct an analytic model for the Braginskii-MHD dynamo in this regime, which successfully matches simulated dynamo growth rates and magnetic-energy spectra. A prediction of this model, confirmed by our numerical simulations, is that a Braginskii-MHD plasma without pressure-anisotropy limiters will not support a dynamo if the ratio of perpendicular and parallel viscosities is too small. This ratio reflects the relative allowed rates of field-line stretching and mixing, the latter of which promotes resistive dissipation of the magnetic field. Finally, in all cases that do exhibit a viable dynamo, the generated magnetic field is organized into folds that persist into the saturated state and bias the chaotic flow to acquire a scale-dependent spectral anisotropy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Self-organization in collisionless, high- β turbulence

The magnetohydrodynamic (MHD) equations, as a collisional fluid model that remains in local thermodynamic equilibrium (LTE), have long been used to describe turbulence in myriad space and astrophysical plasmas. Yet, the vast majority of these plasmas, from the solar wind to the intracluster medium (ICM) of galaxy clusters, are only weakly collisional at best, meaning that significant deviations from LTE are not only possible but common. Recent studies have demonstrated that the kinetic physics inherent to this weakly collisional regime can fundamentally transform the evolution of such plasmas across a wide range of scales. Here, we explore the consequences of pressure anisotropy and Larmor-scale instabilities for collisionless, β $\gg$ 1, turbulence, focusing on the role of a self-organizational effect known as ‘magneto-immutability’. We describe this self-organization analytically through a high-β, reduced ordering of the Chew–Goldberger–Low-MHD (CGL-MHD) equations, finding that it is a robust inertial-range effect that dynamically suppresses magnetic-field-strength fluctuations, anisotropic-pressure stresses and dissipation due to heat fluxes. As a result, the turbulent cascade of Alfvénic fluctuations continues below the putative viscous scale to form a robust, nearly conservative, MHD-like inertial range. These findings are confirmed numerically via Landau-fluid CGL-MHD turbulence simulations that employ a collisional closure to mimic the effects of microinstabilities. We find that microinstabilities occupy a small (~5%) volume-filling fraction of the plasma, even when the pressure anisotropy is driven strongly towards its instability thresholds. We discuss these results in the context of recent predictions for ion-vs-electron heating in low-luminosity accretion flows and observations implying suppressed viscosity in ICM turbulence.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Planar Defect Layers Template a High-Pressure InBi Polymorph

The short- and long-range order of III–V materials under high pressure has long been the subject of debate, with advancements in structural characterization leading to significant revisions to the accepted structural models. Despite these revisions, previous high-pressure structural assignments in the In–Bi system include the site-disordered β-Sn structure type, a structure type demonstrated to be nonexistent in analogous III–V systems. While X-ray diffraction is consistent with site disordering in InBi at high pressure, cluster expansion calculations indicate that disordering requires temperatures above 3000 K. Here, we propose InBi as a model material for studying unique high-pressure planar defects due to its highly anisotropic stress-dependent properties and structure. Specifically, we identify two sets of planar defects that mimic the diffraction pattern of a site disordered β-Sn structure type and are compatible with the calculated disorder barrier. We derive these defects by symmetry relations over crystallographic transitions. Density functional theory calculations of the proposed defects suggest that these defects are stabilized by diminishing interlayer separations with pressure. Further, we find that one of the proposed defects closely resembles a bulk high-pressure phase of InBi, InBi-ϵ, and we assert that the proposed defects order upon heating, acting as a template for InBi-ϵ growth. The proposed defects and their electronic structure provide a basis for the trend of superconducting critical temperature with increasing pressure. These methods for identifying defects are generalizable to other materials with reports of site disorder at high pressure, prompting a broader search for related high-pressure defects.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Modeling brittle fracture due to anisotropic thermal expansion in polycrystalline materials

Here, this work investigated brittle fracture of polycrystalline materials due to thermal stresses arising from anisotropic thermal expansion. We used phase-field fracture simulations with the properties of alpha-uranium (α-U) and assumed a linear elastic mechanical response. Three-dimensional simulations were used to predict fracture for various conditions and crystallographic textures. We found that fracture was more pronounced during cooling than during heating because the anisotropy increased with temperature. We also found that the total crack surface area increased with increasing average misorientation, while the net shape change of the material decreased with increasing misorientation. Two-dimensional simulations in which one crystallographic coefficient of thermal expansion (CTE) was set to zero indicated that the expansion behavior in the crystallographic direction with the smallest CTE was the primary cause of fracture.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Alkali-silica reaction expansion model for confined concrete with stress-dependency and casting direction anisotropy

Alkali-silica reaction (ASR) is a deleterious chemical reaction between alkali hydroxyl ions and types of silica found in some aggregates of concrete. Owners and regulators of nuclear power plants aim to ensure the safety of the concrete structures with optimal maintenance strategies. A new model was developed for predicting the expansion of concrete structures affected by alkali-silica reaction. The model includes a novel combination of existing models as an alkali-silica reaction advancement model, a casting direction anisotropic expansion model, a stress-dependent anisotropic expansion model, and a material property evolution model dependent on the degree of ASR expansion. The model parameters were calibrated based on existing literature data and data generated by previous efforts of this study. The calibrated model was then validated with the experiments carried out in previous efforts of this study. The model was shown to accurately predict the ASR-expansion of large-scale reinforced concrete specimens with confinement.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Geomechanical properties of the Meletta sandstone - the high-temperature heat storage reservoir rock of DeepStor

The DeepStor project aims at storing excess heat at temperatures up to 140 °C in the depleted Leopoldshafen oil field at a depth of about 1300 m. In order to gain knowledge on the target horizons, the different layers of the Meletta sandstone, samples cored in a block retrieved in a quarry near Nussloch where the Meletta sandstone outcrops were studied. Several petrophysical properties were investigated including mineralogy, porosity, permeability, thermal conductivity, P- and S-wave velocities and quality factor. A mechanical study focused on compressive strength under uniaxial and triaxial stress conditions, tensile strength, critical pressure and stress-dependence of physical properties. Our results show that the Meletta sandstone is heterogeneous, anisotropic, mechanically weak, stress-sensitive and prone to water weakening. Petrophysical measurements on few Meletta sandstone cores retrieved in boreholes at about 1250 m depth showed that the outcrop samples are significantly less cohesive and weaker. Therefore, one should consider the Nussloch outcrop as a good reservoir analog only with great caution. Several models were applied to account for our experimental results on anisotropy, mechanical behavior and stress-dependence of the outcrop samples. Our study provides a valuable data set which can feed numerical models to simulate the behavior of the host formation during heat exchange operations in the DeepStor project.

Geomechanics↗
DOE OSTI2021

Strongly anisotropic antiferromagnetic coupling in EuFe 2 As 2 revealed by stress detwinning

Of all parent compounds of iron-based high-temperature superconductors, EuFe 2 As 2 exhibits by far the largest magnetostructural coupling due to the sizable biquadratic interaction between Eu and Fe moments. While the coupling between Eu antiferromagnetic order and Fe structural/antiferromagnetic domains enables rapid field detwinning, this prevents simple magnetometry measurements from extracting the critical fields of the Eu metamagnetic transitions. Furthermore we measure these critical fields by combining x-ray magnetic circular dichroism spectroscopy with in-situ tunable uniaxial stress and applied magnetic field. The combination of two tuning knobs allows us to separate the stressdetwinning of structural domains from the field-induced reorientation of Eu moments. Intriguingly, from the critical field values we find that the Eu interplanar interaction is strongly anisotropic. We argue that this anisotropic exchange term is likely a consequence of the strong anisotropy in the magnetically ordered Fe layer, which highlights the non-trivial interplay between Eu-Fe magnetism in this system.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Overview of a Versatile Loading System for Anisotropic Material Property Characterization

Additive manufacturing, cold rolling, and other thermomechanical treatments on metals, especially HCP, can cause texture and oriented grain structures resulting in anisotropic mechanical properties. This can lead to macroscopic response that significantly deviates from isotropic assumptions which motivates studying mechanical properties in multiple directions. In addition, multiaxial loading and complex stress states overlapping the above mentioned material anisotropy can lead to unexpected outcomes. Idaho National Laboratory developed an advanced mechanical testing system to study a range of uniaxial to multiaxial stress states while measuring the anisotropic response bringing insight into the overlap between material properties and stress states. High-temperature capability and stress- or strain-controlled loading is available to enable a variety of experiment types and conditions to measure elastic, plastic, and viscoplastic properties. This poster presents the design and capabilities of this system with preliminary results highlighting the benefits of multiaxial loading and anisotropic analysis in an integrated system.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Statistical evaluation of microscale stress conditions leading to void nucleation in the weak shock regime

Here, we investigate the heterogeneity of the stress state driven by anisotropic deformation response at the single crystal level through five statistical volume element (SVE) calculations of polycrystalline BCC tantalum. This work focuses on grain boundaries as a prominent material defect type prone to void nucleation based upon experimental observations of predominantly intergranular void nucleation in this material. The SVEs are constructed to be statistically representative of larger volumes of material and are meshed such that mean and standard deviation of grain size and orientation information is reconstructed. The computational meshes feature hexahedral (brick) elements and smooth conformal grain boundaries where significant stress concentration is known to occur, a tail effect of interest in the extreme events process of dynamic ductile damage. An existing micromechanical crystallographic plasticity model shown to capture the single crystal behavior of BCC tantalum well is used to perform the polycrystal calculations. The model includes representation of the non-Schmid effect of non-planar screw dislocation kinetics in tantalum. A three-dimensional stress state time profile predicted by damage modeling of a flyer plate impact experiment is applied as boundary conditions to each SVE. Resulting grain boundary stress state statistics are strongly non-Gaussian. Significant structural evolution is observed within the compressive hold before unloading into tension in the stress profile. Strong angular dependence of grain boundary traction magnitude with shock direction is observed. Non-Schmid effects continue to suggest their influence on propensity of microstructural defect types to nucleate voids. A general void nucleation criterion is proposed using probability theory. The general framework is specified to polycrystalline BCC tantalum in the weak shock regime to include the SVE calculations and literature molecular dynamics calculations of grain boundary void nucleation strength. Probability density functions (PDFs) are used to describe the interaction between the local stress state heterogeneity and the distributed grain boundary void nucleation strength state. A causation entropy maximization procedure removes the requirement for ad hoc selection of a PDF functional form and provides a rigorous procedure for data-based PDF determination. The resulting physically informed PDF describes the spatial appearance frequency of nucleated voids as a function of applied macroscale pressure. Lower length scale physics are thus packaged in a precise and computationally efficient way to provide computational plasticity insight to macroscale dynamic ductile damage models.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Multicationic interactions mitigating lattice strain in sodium layered cathodes

Transition-metal (TM) layered oxides have emerged as the primary cathode choice for sodium-ion batteries (SIBs) due to their high energy density and sustainable chemistry using non-critical elements. However, their anisotropic lattice strain and stress accumulation during (de)sodiation lead to severe structural degradation, yet an intrinsic strain-depressant approach remains elusive. Herein, we propose entropy regulation with zero Li/Co usage to mitigate harmful lattice displacements and enhance the electrochemical performance of sodium layered cathodes. Our findings demonstrate that high entropy design effectively inhibits TMO 6 octahedra distortions upon cycling, as evidenced by hard X-ray absorption spectroscopy, greatly reducing near-surface structural deconstruction and interface side reactions. Furthermore, multicationic interactions driven by configurational entropy thermodynamically mitigate the formation of oxygen defects and strengthen ligand-to-metal coordination. The complementarity inherent in charge compensation within complex systems is unveiled and the restrained lattice parameters deviations without interior volume residuals are successfully achieved. As a result, the multicationic cathode exhibits improved cycling stability and Na + diffusion kinetics in both half and full cells. The cathode chemistries outlined here broaden the prospects for lattice engineering to alleviate bulk fatigue and open up the possibility to develop an economically viable layered oxides with long durability.

Wang, Haoji [Central South University, Changsha (C↗
DOE OSTI2022

Strain-retardant coherent perovskite phase stabilized Ni-rich cathode

The use of state-of-the-art Ni-rich layered oxides (LiNi x Co y Mn 1-x-y O 2 , x > 0.5) as the cathode material for lithium-ion batteries can push the energy and power density to a higher level than is currently available. However, volume variation associated with anisotropic lattice strain and stress that is being developed during lithium (de) intercalation induces severe structural instability and electrochemical decay of the cathode materials, which is amplified further when the battery is operating at a high voltage (above 4.5 V), which is essential for unlocking its high energy. Even after much effort by the research community, an intrinsic strain-retardant method for directly alleviating the continuous accumulation of lattice strain remains elusive. By introducing a coherent perovskite phase into the layered structure functioning as a ‘rivet’, we significantly mitigate the pernicious structural evolutions by a pinning effect. The lattice strain evolution in every single cycle is markedly reduced by nearly 70% when compared with conventional materials, which significantly enhances morphological integrity leading to a notable improvement in battery cyclability. This strain-retardant approach broadens the perspective for lattice engineering to release the strain raised from lithium (de)intercalation and paves the way for the development of high-energy-density cathodes with long durability.

25 ENERGY STORAGE↗
DOE OSTI2026

A critical review on additive manufacturing of refractory alloys from a data analytics perspective- beyond nickel-based superalloys

Refractory alloys (RAs) are promising materials due to their exceptional physicochemical properties, but most research remains at the laboratory scale. For broader adoption, advancements in manufacturing are essential. Because their high stability makes conventional methods like machining and casting difficult, additive manufacturing (AM) is emerging as an effective approach for fabricating refractory alloy components. However, AM's repeated non-equilibrium thermal cycles introduce undesired features (e.g. defects, anisotropic microstructures, and residual stresses), which are magnified due to RAs’ unique properties. This paper comprehensively reviews the state-of-the-art methods of AM for refractory alloys. It explores data analytics techniques to establish design rules based on multi-fidelity experimental and computational methods. Furthermore, it investigates integrated, collaborative efforts to harmonise standalone databases, information, knowledge, and predictive models at multi-physics, multi-stage, and multi-scale. Unlike the existing literature that focuses primarily on material systems or process fundamentals, this work provides an integrated perspective on AM of refractory alloys from a data analytics standpoint, highlighting the roles of integrated computational materials engineering (ICME), verification, validation, and uncertainty quantification (VV&UQ), and digital twin-driven qualification in overcoming data scarcity and accelerating rapid qualification.

Additive manufacturing↗
DOE OSTI2022

MODELLING FIBER ORIENTATION DURING ADDITIVE MANUFACTURING COMPRESSION MOLDING PROCESSES

The production of high-performance thermoplastic composites reinforced with short carbon fibers can be achieved by a novel “additive manufacturing-compression molding” technique. An advantage of such combination is two-fold: controlled fiber orientation in additive manufacturing and less void content by compression molding. In this study, a computational fluid dynamics model has been developed to predict the behavior of printed layers during fiber-reinforced thermoplastic extrusion and subsequent compression molding. The fiber orientation was modelled with a simple quadratic closure model. The interaction between the fibers is included using a rotary diffusion coefficient which becomes significant in concentrated regimes. Finally, the second order orientation tensor is coupled with the momentum equation as an anisotropic part of the stress term. The effect of processing parameters on the behavior of printed layers was investigated to determine the favorable printing scenarios. The developed numerical model enables design of high-performance composites with tunable mechanical properties.

Seta, Berin↗
DOE OSTI2021

Plasticity and fracture behavior of Inconel 625 manufactured by laser powder bed fusion: Comparison between as-built and stress relieved conditions

In this work, the influence of stress relief on the plasticity and fracture behavior of Inconel 625 fabricated through laser powder bed fusion additive manufacturing (AM) was investigated. The as-built versus stress relieved microstructures were compared, showing similar grain structures but the presence of ~10 vol % δ phase in the stress relieved condition, and no δ phase in the as-built condition. Mechanical tests under plane strain tension were performed on the stress relieved samples, and an anisotropic plasticity model was calibrated and validated using finite element simulations. Uniaxial and notched tension tests were performed on both as-built and stress relieved samples to probe the effect of stress relief on stress state- and direction-dependent fracture behavior. It was found that on average, the fracture strain of the stress relieved samples along the build direction was 30% higher than that along the perpendicular build direction in the stress state range studied, and the stress relief heat treatment resulted in a 45% decrease in fracture strain. The fracture strain in stress relieved samples was more strongly dependent on stress state than in as-built samples.

36 MATERIALS SCIENCE↗