Search NASA⌕ Search

SEARCH · Search NASA

Results for “area optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Development of metallization process: FSA project, cella and module formation research area

The optimization, evaluation, and demonstration of a novel metallization applied by a screen printing process is examined. Based on previous results of High Resolution, Low Cost Solar Cell Contact Development, a paste consisting of molybdenum, tin, and titanium hydride was selected as the promising composition. No satisfactory cells were made using any of the molybdenum/tin pastes used as a complete replacement for conventional silver pastes. The major problem is the inability to form a bond between the pastes and silicon that withstands soldering.

Garcia, A., III↗
NASA NTRS1981

Automation of On-Board Flightpath Management

The status of concepts and techniques for the design of onboard flight path management systems is reviewed. Such systems are designed to increase flight efficiency and safety by automating the optimization of flight procedures onboard aircraft. After a brief review of the origins and functions of such systems, two complementary methods are described for attacking the key design problem, namely, the synthesis of efficient trajectories. One method optimizes en route, the other optimizes terminal area flight; both methods are rooted in optimal control theory. Simulation and flight test results are reviewed to illustrate the potential of these systems for fuel and cost savings.

Erzberger, H.↗
NASA NTRS1981

Determination of the optimal level for combining area and yield estimates

Several levels of obtaining both area and yield estimates of corn and soybeans in Iowa were considered: county, refined strata, refined/split strata, crop reporting district, and state. Using the CCEA model form and smoothed weather data, regression coefficients at each level were derived to compute yield and its variance. Variances were also computed with stratum level. The variance of the yield estimates was largest at the state and smallest at the county level for both crops. The refined strata had somewhat larger variances than those associated with the refined/split strata and CRD. For production estimates, the difference in standard deviations among levels was not large for corn, but for soybeans the standard deviation at the state level was more than 50% greater than for the other levels. The refined strata had the smallest standard deviations. The county level was not considered in evaluation of production estimates due to lack of county area variances.

Bauer, M. E.↗
NASA NTRS1973

An historical survey of computational methods in optimal control.

Review of some of the salient theoretical developments in the specific area of optimal control algorithms. The first algorithms for optimal control were aimed at unconstrained problems and were derived by using first- and second-variation methods of the calculus of variations. These methods have subsequently been recognized as gradient, Newton-Raphson, or Gauss-Newton methods in function space. A much more recent addition to the arsenal of unconstrained optimal control algorithms are several variations of conjugate-gradient methods. At first, constrained optimal control problems could only be solved by exterior penalty function methods. Later algorithms specifically designed for constrained problems have appeared. Among these are methods for solving the unconstrained linear quadratic regulator problem, as well as certain constrained minimum-time and minimum-energy problems. Differential-dynamic programming was developed from dynamic programming considerations. The conditional-gradient method, the gradient-projection method, and a couple of feasible directions methods were obtained as extensions or adaptations of related algorithms for finite-dimensional problems. Finally, the so-called epsilon-methods combine the Ritz method with penalty function techniques.

Polak, E.↗
NASA NTRS1976

Optimized metallization patterns for large-area silicon solar cells

Design criteria is presented for optimizing the front-surface metallization pattern of large-area silicon solar cells. A computer program calculates the spacing of metal fingers which minimizes resistive and shadowing losses. Finger spacing and efficiency for the optimum design are presented as a function of finger width and cell size. It is shown that quantitative evaluation of metallization pattern options can be made without cell fabrication.

Matzen, W. T.↗
NASA NTRS1993

Optimal thresholds for the estimation of area rain-rate moments by the threshold method

Optimization of the threshold method, achieved by determination of the threshold that maximizes the correlation between an area-average rain-rate moment and the area coverage of rain rates exceeding the threshold, is demonstrated empirically and theoretically. Empirical results for a sequence of GATE radar snapshots show optimal thresholds of 5 and 27 mm/h for the first and second moments, respectively. Theoretical optimization of the threshold method by the maximum-likelihood approach of Kedem and Pavlopoulos (1991) predicts optimal thresholds near 5 and 26 mm/h for lognormally distributed rain rates with GATE-like parameters. The agreement between theory and observations suggests that the optimal threshold can be understood as arising due to sampling variations, from snapshot to snapshot, of a parent rain-rate distribution. Optimal thresholds for gamma and inverse Gaussian distributions are also derived and compared.

Short, David A.↗
NASA NTRS2002

A survey of spacecraft formation flying guidance

This paper is the first comprehensive spacecraft formation flying guidance (FFG) survey. Here by the term guidance we mean both path planning (i. e., reference trajectory generation) and optimal, open loop control design. FFG naturally divides into two areas: Deep Space (DS), in which relative spacecraft dynamics reduce to double integrator form, and Planetary Orbital Environments (POE), in which they do not (e.9. libration point formations). Both areas consider optimal formation reconfigurations. In addition, DS FFG addresses optimal u, v-coverages for multiple spacecraft interferometers and rest-to-rest rotations. The main focus of the POE literature, however, is 'assive apertures.' These are periodic and fuel-eficient relative spacecraft trajectories that accomplish scientific objectives (e.9. synthesizing an aperture).

formation flying guidance optimal control path pla↗
NASA NTRS1972

The application of optimal control technqiues to advanced manned missions, volume 1

Two problems are presented in the area of optimal control and its application to the design of attitude control systems for advanced complex aerospace vehicles. The problems discussed are specification of performance criteria in terms of structural load minimization and/or maximum orbital payload injection requirements of the controlled vehicle; and formulation and solution of the optimization problem such that practical control systems are obtained.

Connor, C. L.↗
NASA NTRS1982

Economic Evaluation of Dual-Level-Residence Solar-Energy System

105-page report is one in a series of economic evaluations of different solar-energy installations. Using study results, an optimal collector area is chosen that minimizes life-cycle costs. From this optimal size thermal and economic performance is evaluated.

Source record↗
NASA NTRS1994

Natural frequency of uniform and optimized tetrahedral truss platforms

Qualitative and quantitative estimates for the fundamental frequency of uniform and optimized tetrahedral truss platforms are determined. A semiempirical equation is developed for the frequency of free-free uniform trusses as a function of member material properties, truss dimensions, and parasitic (nonstructural) mass fraction Mp/Mt. Optimized trusses with frequencies approximately two times those of uniform trusses are determined by varying the cross-sectional areas of member groups. Trusses with 3 to 8 rings, no parasitic mass, and member areas up to 25 times the minimum area are optimized. Frequencies computed for ranges of both Mp/Mt and the ratio of maximum area to minimum area are normalized to the frequency of a uniform truss with no parasitic mass. The normalized frequency increases with the number of rings, and both frequency and the ratio of maximum area to minimum area decrease with increasing Mp/Mt. Frequency improvements that are achievable with a limited number of member areas are estimated for a 3-ring truss by using Taguchi methods. Joint stiffness knockdown effects are also considered. Comparison of optimized and baseline uniform truss frequencies indicates that tailoring can significantly increase structural frequency; maximum gains occur for trusses with low values of Mp/Mt. This study examines frequency trends for ranges of structural parameters and may be used as a preliminary design guide.

Wu, K. Chauncey↗
NASA NTRS1989

Applications of integrated design/analysis systems in aerospace structural design

Integrated structural analysis and design systems and structural optimization procedures are being used in a production environment. Successful use of these systems requires experienced personnel. Interactive computer graphics can and will play a significant role in the analysis, optimization, design and manufacturing areas. Practical structural optimization procedures are tools that must be made available to the team. Much work still needs to be done to tie finite-element modeling to actual design details which are being tracked on systems such as CADAM or CATIA. More work needs to be done to automate the detailed design and analysis process. More emphasis should be placed on the real design problems.

Mason, Philip↗
NASA NTRS1989

Recent experience in simultaneous control-structure optimization

To show the feasibility of simultaneous optimization as design procedure, low order problems were used in conjunction with simple control formulations. The numerical results indicate that simultaneous optimization is not only feasible, but also advantageous. Such advantages come at the expense of introducing complexities beyond those encountered in structure optimization alone, or control optimization alone. Examples include: larger design parameter space, optimization may combine continuous and combinatoric variables, and the combined objective function may be nonconvex. Future extensions to include large order problems, more complex objective functions and constraints, and more sophisticated control formulations will require further research to ensure that the additional complexities do not outweigh the advantages of simultaneous optimization. Some areas requiring more efficient tools than currently available include: multiobjective criteria and nonconvex optimization. Efficient techniques to deal with optimization over combinatoric and continuous variables, and with truncation issues for structure and control parameters of both the model space as well as the design space need to be developed.

Salama, M.↗
NASA NTRS1972

Application of optimization techniques to near terminal area sequencing and flow control.

Development of an arrival air-traffic management system for a single runway. Traffic is segregated throughout most of the near terminal area according to performance characteristics. Nominal approach routes for each class of aircraft are determined by an optimization procedure. In this fashion, the nominal approach routes are dependent upon and, hence, determined by the near terminal area operating capabilities of each class of aircraft. The landing order and spacing of aircraft on the common approach path are determined so that a measure of total system deviation from the nominal landing times is minimized and safety standards are met. Delay maneuvers required to satisfy sequencing needs are then carried out in a manner dependent upon the particular class of aircraft being maneuvered. Finally, results are presented to illustrate the effects of the rate of arrivals upon a one-runway system serving three different classes of aircraft employing several different sequencing strategies and measures of total system deviation.

Straeter, T. A.↗
NASA NTRS1992

Project WISH: The Emerald City

Phase 3 of Project WISH saw the evolution of the Emerald City (E-City) from a collection of specialized independent analyses and ideas to a working structural design integrated with major support systems and analyses. Emphasis was placed on comparing and contrasting the closed and open cycle gas core nuclear rocket engines to further determine the optimum propulsive system for the E-City. Power and thermal control requirements were then defined and the question of how to meet these requirements was addressed. Software was developed to automate the mission/system/configuration analysis so changes dictated by various subsystem constraints could be managed efficiently and analyzed interactively. In addition, the liquid hydrogen propellant tank was statically designed for minimum mass and shape optimization using a finite element modeling package called SDRC I-DEAS. Spoke and shaft cross-sectional areas were optimized on ASTROS (Automated Structural Optimization System) for mass minimization. A structural dynamic analysis of the optimal structure also conducted using ASTROS enabled a study of the modes, frequencies, displacements, and accelerations of the E-City. Finally, the attitude control system design began with an initial mass moment of inertia analysis and was then designed and optimized using linear quadratic regulator control theory.

Oz, Hayrani↗
NASA NTRS1992

Project Wish: The Emerald City, phase 3

Phase 3 of Project Wish saw the evolution of the Emerald City (E-City) from a collection of specialized independent analyses and ideas to a working structural design integrated with major support systems and analyses. Emphasis was placed on comparing and contrasting the closed and open cycle gas core nuclear rocket engines to further determine the optimum propulsive system for the C-City. Power and thermal control requirements were then defined and the question of how to meet these requirements was addressed. Software was developed to automate the mission/system/configuration analysis so changes dictated by various subsystems constraints could be managed efficiently and analyzed interactively. In addition, the liquid hydrogen propellant tank was statically designed for minimum mass and shape optimization using a finite element modeling package called SDRC I-DEAS while spoke and shaft cross-sectional areas were optimized on ASTROS (Automated Structural Optimization System). A structural dynamic analysis also conducted using ASTROS enabled a study of the displacements, accelerations, modes and frequencies of the C-City. Finally, the attitude control system design began with an initial mass moment of inertia analysis and was then designed and optimized using linear quadratic regulator control theory.

Source record↗
NASA NTRS2004

Multidisciplinary Design Optimization for Aeropropulsion Engines and Solid Modeling/Animation via the Integrated Forced Methods

The grant closure report is organized in the following four chapters: Chapter describes the two research areas Design optimization and Solid mechanics. Ten journal publications are listed in the second chapter. Five highlights is the subject matter of chapter three. CHAPTER 1. The Design Optimization Test Bed CometBoards. CHAPTER 2. Solid Mechanics: Integrated Force Method of Analysis. CHAPTER 3. Five Highlights: Neural Network and Regression Methods Demonstrated in the Design Optimization of a Subsonic Aircraft. Neural Network and Regression Soft Model Extended for PX-300 Aircraft Engine. Engine with Regression and Neural Network Approximators Designed. Cascade Optimization Strategy with Neural network and Regression Approximations Demonstrated on a Preliminary Aircraft Engine Design. Neural Network and Regression Approximations Used in Aircraft Design.

Source record↗