Search NASA⌕ Search

SEARCH · Search NASA

Results for “augmentor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

A study of noise source location on a model scale augmentor wing using correlation techniques

An experimental investigation, conducted on a model-scale augmentor wing to identify the sources of far-field noise, is examined. The measurement procedure followed in the investigation involved the cross-correlation of far field sound pressures with fluctuating pressures on the surface of the augmentor flap and shroud. In addition pressures on the surfaces of the augmentor were cross-correlated. The results are interpreted as showing that the surface pressure fluctuations are mainly aerodynamic in character and are convected in the downstream direction with a velocity which is dependent on the jet exhaust velocity. However the far field sound levels in the mid and high frequency ranges are dominated by jet noise. There is an indication that in the low frequency range trailing edge noise, associated with interaction of the jet flow and the flap trailing edge, plays a significant role in the radiated sound field.

Wilby, J. F.↗
NASA NTRS1976

Effect of swirling flow on augmentor performance, phase 2

A test program has been conducted with an augmentor that employed swirling flow as a means of promoting rapid flame propagation. The program measured the trajectory and dispersion of JP-5-type kerosene sprayed into a strongly swirling flowfield. Using the data obtained, a set of sprayrings was designed and evaluated in the augmentor at conditions simulating those typical of augmented turbojet engines. At the inlet test temperature of 649 C the swirling flowfield had no effect on the radial position of the fuel spray. The augmentor demonstrated combustion efficiencies greater than 95% over most of the operating range, which extended from an equivalence ratio of 0.2 to over 1.0.

Clements, T. R.↗
NASA NTRS1977

Thrust augmentor application for STOL and V/STOL

A general parametric description is suggested for thrust augmentor application to STOL and V/STOL aircraft. The parameters and their relationships are discussed using several aircraft augmentor integration problems. For a STOL transport design, the ram drag is a key consideration, limiting the maximum gross augmentation that can be utilized. Maximizing gross augmentation and balancing the aircraft are key considerations for a V/STOL fighter design. Results from wind tunnel investigations on several different thrust augmentor concepts and system studies on STOL transport designs are also included.

Aiken, T. N.↗
NASA NTRS1977

The transonic multi-foil Augmentor-Wing

The paper describes the development of a transonic blown multi-foil Augmentor-Wing airfoil section that has a thickness/chord (t/c) value of 0.18. In comparison with an unblown single-foil supercritical section of the same overall t/c the new multi-foil section is characterized by an increased drag rise Mach number, increased buffet boundaries, and a reduction in 'effective' drag due to blowing. Potential advantages of the Augmentor-Wing are considered and the testing of three high-speed models in a trisonic pressurized wind tunnel (possessing a two-dimensional transonic insert) is discussed. The data indicate that a very thick wing is feasible since separations toward the rear of the main foil can be controlled both by shroud location and augmentor blowing.

Farbridge, J. E.↗
NASA NTRS1979

The external augmentor concept for V/STOL aircraft

The beneficial aspects of an ejector powered V/STOL concept were reviewed. The feasibility of satisfactorily incorporating an ejector system in a high performance V/STOL aircraft was investigated. The external augmentor concept, based on the use of chordwise ejector slots, is presented. It is concluded that the external augmentor concept has a basic inherent simplicity and a sufficient augmentor performance potential to make feasible a high performance V/STOL aircraft based on ejectors.

Whittely, D. C.↗
NASA NTRS1980

Phase 2 and 3 wind tunnel tests of the J-97 powered, external augmentor V/STOL model

Modifications were made to the model to improve longitudinal acceleration capability during transition from hovering to wing borne flight. A rearward deflection of the fuselage augmentor thrust vector is shown to be beneficial in this regard. Other agmentor modifications were tested, notably the removal of both endplates, which improved acceleration performance at the higher transition speeds. The model tests again demonstrated minimal interference of the fuselage augmentor on aerodynamic lift. A flapped canard surface also shows negligible influence on the performance of the wing and of the fuselage augmentor.

Garland, D. B.↗
NASA NTRS1972

Predicted flight characteristics of the augmentor wing jet STOL research aircraft

An existing deHavilland C-8A airplane has been modified into an augmentor wing flight test vehicle. Research objectives are to verify the augmentor flap concept and to produce data for STOL airworthiness criteria. The Modified C-8A provides the means for jet-STOL flight research down to a 60 knot approach speed. The airplane has a high thrust-to-weight ratio, high-lift flap system, vectored thrust, powerful flight controls, and lateral-directional stability augmentation system. Normal performance and handling qualities are expected to be satisfactory. Analysis and piloted simulator results indicate that stability and control characteristics in conventional flight are rated satisfactory. Handling qualities in the STOL regime are also generally satisfactory, although pilot workload is high about the longitudinal axis.

Spitzer, R. E.↗
NASA NTRS1972

An analysis of the takeoff and landing performance of a jet-powered STOL augmentor wing design

A preliminary study of the takeoff and landing performance characteristics of a swept wing airplane with augmented jet flap, designed for STOL operation and low noise is presented. The study is based on aerodynamic data from wind tunnel tests of a large-scale swept augmentor wing model, scaled up to a 48,000 pound airplane. Engine characteristics are based on a turbo fan with a fan pressure ratio of 2.5 delivering the major portion of the thrust to the augmentor flap. A description of the overall airplane configuration, the propulsion system, and the use of the aerodynamics is presented. To assess the STOL performance of the airplane, takeoff and landing distances and flight path capabilities were computed at various flap deflections and thrust levels. After evaluating these results in terms of desired STOL performance with required margins, basic takeoff and landing configurations were chosen.

Post, S. E.↗
NASA NTRS1972

Design integration and noise study for a large STOL augmentor wing transport

Analysis, design, experimental static testing, wind-tunnel testing, and design integration studies are used to develop an augmentor wing jet flap configuration for a jet STOL transport aircraft having maximum propulsion and aerodynamic performance with minimum noise generation. The program has three basic elements: (1) static testing of a scale wing section to demonstrate augmentor performance and noise characteristics; (2) two-dimensional wind-tunnel testing to determine flight-speed effects on performance, and (3) system design and evaluation that optimizes the complete system and ensures that the design is compatible with the requirements for a large STOL transport having a 500-foot sideline noise of 95 perceived noise decibels (PNdb) or less.

Okeeke, J. V.↗
NASA NTRS1972

Simulator evaluation of the flying qualities of externally blown flap and augmentor wing transport configurations

Concurrent simulations of powered-lift STOL transport aircraft having either an externally blown flap configuration or an augmentor wing configuration were conducted. The following types of simulators of varying sophistication were used: (1) a simple fixed-base simulation with a simple visual display, (2) a more complex fixed-base simulation using a realistic transport cockpit and a high-quality visual display, and (3) a six-degree-of-freedom motion simulator that had a realistic transport cockpit and a sophisticated visual display. The unaugmented flying qualities determined from these simulations were rated as unacceptable for both the externally blown flap and augmentor wing configurations. The longitudinal, lateral-directional, and single-engine-failure characteristics were rated satisfactory with extensive augmentation, including pitch and roll command systems, flight-path (or speed) augmentation, turn coordination, and effective yaw damping. However, the flare and landing characteristics from any approach glide-path angle in excess of 4 deg were rated as unsatisfactory but acceptable.

Kier, D. A.↗
NASA NTRS1972

Preliminary results of flight tests of the augmentor-wing jet STOL research aircraft

The Augmentor-Wing Jet STOL Research Aircraft has been developed and has started flight tests. The objectives of the program are to compare aerodynamic characteristics predicted from wind-tunnel data with data obtained in flight, to determine flight dynamic characteristics and limitations of the augmentor-wing concepts, and to contribute to the development of STOL design and operational criteria. Initial flight test results have shown that the aerodynamic characteristics are close to values predicted from wind-tunnel tests. The lateral-directional stability and control characteristics are satisfactory for research STOL missions with stability augmentation, but the longitudinal control require improvement. STOL take-off distance over 11 m is about 290 m, and landing approach speeds are between 60 and 65 knots. The investigation of the STOL operational and performance characteristics is continuing.

Quigley, H. C.↗
NASA NTRS1974

The augmentor wing - Powered-lift STOL a proven concept

A jet-STOL powered-lift aircraft has the ability to perform a relatively steep (7.5 deg) final approach at high power setting and a low speed. The DHC-5 Buffalo/Spey Augmentor-Wing research aircraft is the first machine of its kind to accomplish this performance. The aircraft uses an approach in which the cold bypass thrust is vectored by the augmentor flap. Aspects of aircraft reliability are discussed together with taxi trials, stalling characteristics, lateral directional control, single-engine operations, roll acceleration, and flight in turbulent conditions.

Whittley, D. C.↗
NASA NTRS1977

Acoustic tests of augmentor wing model

Acoustic and aerodynamic data were obtained for a full-scale section of an augmentor wing. Features of the design included a single-row, multielement nozzle array and acoustically tuned panels placed on the interior surfaces of the augmentor. When the data were extrapolated to a 91,000-kilogram aircraft, the calculated sideline perceived noise levels were approximately the same for either the takeoff or approach condition.

Goodykoontz, J. H.↗
NASA NTRS1979

Theoretical analysis of an augmentor wing for a VTOL fighter

A method based on potential flow theory was developed for predicting forces and moments acting on augmentor wings for prescribed ejector jet characteristics. A three dimensional nonplanar vortex lattice is laid out on the chordal planes of the augmentor wing components. Jet induced effects are included in the boundary condition from which the horseshoe vortex strengths are obtained. The jet within the diffusor is made to expand from the primary nozzles to the diffusor exit and is represented by a distribution of vorticity on the jet boundary to provide proper entrainment. The jet downstream of the diffusor exit is modeled by a vorticity distribution and blockage panels and its centerline location and spreading rate are taken from experimental data. The vortex lattice and jet models are used in an iterative manner until the predicted diffusor exit velocity matches the specified one. Some comparisons with available data show good agreement at lower power settings.

Dillenius, M. F. E.↗
NASA NTRS1982

Grid generation by elliptic partial differential equations for a tri-element Augmentor-Wing airfoil

Two efforts to numerically simulate the flow about the Augmentor-Wing airfoil in the cruise configuration using the GRAPE elliptic partial differential equation grid generator algorithm are discussed. The Augmentor-Wing consists of a main airfoil with a slotted trailing edge for blowing and two smaller airfoils shrouding the blowing jet. The airfoil and the algorithm are described, and the application of GRAPE to an unsteady viscous flow simulation and a transonic full-potential approach is considered. The procedure involves dividing a complicated flow region into an arbitrary number of zones and ensuring continuity of grid lines, their slopes, and their point distributions across the zonal boundaries. The method for distributing the body-surface grid points is discussed.

Sorenson, R. L.↗
NASA NTRS1984

Viscous-inviscid aerodynamic analysis of two-dimensional thrust augmentors

A theory for the computation of two-dimensional thrust augmentor performance is developed. The flow field is assumed to be incompressible, of uniform density and statistically steady. The flow in and around the augmentor is assumed to consist of an outer, inviscid part and an inner, viscous part. The outer field is calculated analytically and then matched with the inner, viscous field, which is computed by means of integral methods. This form of analysis leads to a simple and economical approach, particularly useful for conducting parametric studies. The theoretical results are compared with recently acquired experimental data.

Tavella, D. A.↗
NASA NTRS1985

Transonic separated solutions for an augmentor-wing

The viscous transonic flow about a multielement airfoil (augmentor-wing) is simulated by coupling full-potential and direct/inverse differential boundary-layer algorithms. Solutions have been obtained for a variety of conditions and are in fair agreement with available experimental data. Typical results from this transonic augmentor-wing code (TAUG-V) require approximately three minutes of CRAY-XMP CPU time. Since this viscous transonic code accounts for most of the important flow physics, yet is still economical, it is a practical tool for the design aerodynamicist.

Flores, J.↗