Results for “automated fiber placement” — Page 2

NASA NTRSDate not supplied

Manufacturing Trials of Integrally Stiffened Composite Panels Using Automated Fiber Placement

Commercial aircraft structures are frequently manufactured from carbon-epoxy materials because of their weight and stiffness advantages compared to metallic materials. Wing cover panels are regularly manufactured using an automated fiber placement (AFP) process, but current design and manufacturing methodologies do not fully take advantage of the opportunities afforded by AFP. Design and manufacturing studies were undertaken at the NASA Langley Research Center at the Integrated Structural Assembly of Advanced Composites (ISAAC) facility to quantify manufacturing benefits and limitations associated with AFP to create structurally efficient integral stiffeners as an alternative to bonded or mechanically fastened stiffeners. This methodology could save weight and remove failure mechanisms by reducing the need for rivets and bonding materials since the stiffener plies are interleaved within the skin plies. The use of AFP with integral stiffeners can open the design space, but a fundamental, systematic evaluation of manufacturing limitations is necessary. Manufacturing trials are described herein, where considered manufacturing variables included stiffener location, stiffener course staggering, stiffener widths, stiffener intersections, and material thicknesses for both the skin and stiffener plies. The manufacturing process and lessons learned from each trial are described, including the most successful current design which contains staggered stiffeners, non-traditional laminate angles, and a combination of multiple material thicknesses within the same laminate.

Automated Fiber Placement↗

NASA NTRSDate not supplied

Manufacturing Trials of Integrally Stiffened Composite Panels Using Automated Fiber Placement

Commercial aircraft structures are frequently manufactured from carbon-epoxy materials because of their weight and stiffness advantages compared to metallic materials. Wing cover panels are regularly manufactured using an automated fiber placement (AFP) process, but current design and manufacturing methodologies do not fully take advantage of the opportunities afforded by AFP. Design and manufacturing studies were undertaken at the NASA Langley Research Center at the Integrated Structural Assembly of Advanced Composites (ISAAC) facility to quantify manufacturing benefits and limitations associated with AFP to create structurally efficient integral stiffeners as an alternative to bonded or mechanically fastened stiffeners. This methodology could save weight and remove failure mechanisms by reducing the need for rivets and bonding materials since the stiffener plies are interleaved within the skin plies. The use of AFP with integral stiffeners can open the design space, but a fundamental, systematic evaluation of manufacturing limitations is necessary. Manufacturing trials are described herein, where considered manufacturing variables included stiffener location, stiffener course staggering, stiffener widths, stiffener intersections, and material thicknesses for both the skin and stiffener plies. The manufacturing process and lessons learned from each trial are described, including the most successful current design which contains staggered stiffeners, non-traditional laminate angles, and a combination of multiple material thicknesses within the same laminate.

Composite manufacturing↗

NASA NTRSDate not supplied

Laser Angle of Incidence Effects on in-Situ Consolidation of Automated Fiber Placement of Polyaryletherketone Composites

NASA and Electroimpact, Inc. ®†† in conjunction with other U.S. industry partners are performing research as a part of the NASA High-rate Composites for Aircraft Manufacturing (HiCAM) Project to fabricate thermoplastic panels using automated fiber placement (AFP) to increase manufacturing rates of aircraft structural composites. This work focuses on evaluating the in-situ consolidation AFP of thermoplastics (ICAT) process. Previous studies of the ICAT process using semi-crystalline, polyaryletherketone (PAEK) slit-tape have resulted in an adequate degree of intimate contact between plies; however, the resulting interlaminar strength have been less than laminates fabricated in an autoclave. To improve these properties, the effect of reducing the laser angle of incidence (AoI) during placement to increase the degree of auto-hesion was evaluated. The AoI of the laser assisted AFP head was varied between 12° and 16° to fabricate multiple quasi- isotropic and unidirectional test panels. Physics-based thermal models developed at the NASA Langley Research Center were utilized to predict the temperature profile. Laminate processing temperature was measured experimentally, and panel quality was evaluated by both non- destructive evaluation (NDE) as well as destructively by photo-microscopy. The effect on interlaminar strength was determined by short beam strength testing. Test results of carbon fiber laminates fabricated by ICAT using polyetheretherketone (PEEK), polyetherketoneketone (PEKK), and low-melt polyaryletherketone (LM-PAEK) at various laser angles of incidence, placement temperatures and placement speeds are presented.

Laser↗

NASA NTRSDate not supplied

Laser Angle of Incidence Effects on in-Situ Consolidation of Automated Fiber Placement of Polyaryletherketone Composites

NASA and Electroimpact, Inc. ® in conjunction with other U.S. industry partners are performing research as a part of the NASA High-rate Composites for Aircraft Manufacturing (HiCAM) Project to fabricate thermoplastic panels using automated fiber placement (AFP) to increase manufacturing rates of aircraft structural composites. This work focuses on evaluating the in-situ consolidation AFP of thermoplastics (ICAT) process. Previous studies of the ICAT process using semi-crystalline, polyaryletherketone (PAEK) slit-tape have resulted in an adequate degree of intimate contact between plies; however, the resulting interlaminar strength have been less than laminates fabricated in an autoclave. To improve these properties, the effect of reducing the laser angle of incidence (AoI) during placement to increase the degree of auto-hesion was evaluated. The AoI of the laser assisted AFP head was varied between 12° and 16° to fabricate multiple quasi-isotropic and unidirectional test panels. Physics-based thermal models developed at the NASA Langley Research Center were utilized to predict the temperature profile. Laminate processing temperature was measured experimentally, and panel quality was evaluated by both non-destructive evaluation (NDE) as well as destructively by photo-microscopy. The effect on interlaminar strength was determined by short beam strength testing. Test results of carbon fiber laminates fabricated by ICAT using polyetheretherketone (PEEK), polyetherketoneketone (PEKK), and low-melt polyaryletherketone (LM-PAEK) at various laser angles of incidence, placement temperatures and placement speeds are presented.

Thermoplastic Composites↗

NASA NTRS2019

Design and Analysis of a Tool for Automated Fiber Placement of Composite Wind Tunnel Blades

For decades, composite wind tunnel blades have been constructed using labor-intensive hand layup processes. Automated Fiber Placement (AFP) is a relatively new technology that has not seen widespread use in manufacturing composite wind tunnel blades. AFP offers the potential for reduced manufacturing time, reduced cost, and improved consistency compared to traditional hand layup procedures. These manufacturing qualities are becoming increasingly important as existing wind tunnel blades are replaced due to impact damage or wear and tear from decades of use. Researchers at the NASA Langley Research Center are currently using the Integrated Structural Assembly of Advanced Composites (ISAAC) facility to investigate the feasibility of AFP for manufacturing composite wind tunnel blades. ISAAC uses manufacturing tools as surfaces on which to place fiber tows. A manufacturing tool was developed for using AFP to build a wind tunnel blade shape. This paper presents the structural design and analysis of this tool, for use with AFP, constructed from high temperature thermoplastics. The tool fabricated by this design process was successfully used for AFP and oven cure of two representative airfoil shaped composite structures.

Brian Mason↗

NASA NTRSDate not supplied

RESIDUAL DEFORMATION ANALYSIS IN COMPOSITE SHELL STRUCTURES MANUFACTURED USING AUTOMATED FIBER PLACEMENT

The manufacturing of composites typically produces residual stresses that can significantly affect the final shape of the structure. The process of automated fiber placement (AFP) has become a prominent manufacturing technique in developing layups with tailored, variable stiffness morphology. The steered patterns of fiber tows with and without overlaps produce residual deformations that are distinctive from traditional layups. Digital image correlation was used to measure the AFP lamina coefficients of thermal expansion, which were incorporated into finite element analyses (FEA) to model the cooling phase of the cure cycle. The effects of nonlinear analysis and temperature-dependent lamina properties calculated using self-consistent field micromechanics, on the resulting residual deformation of shells, were also modeled. The predicted residual deformation was analyzed by considering out-of-roundness in cylindrical shells and compared to the experimental results. The shell FEA results were well-correlated with the overall deformed shape of the AFP cylinder with overlaps, while the shell FEA model of the AFP cylinder without overlaps did not show as good of qualitative match of the deformation pattern. Analytical correlation with measured results were insensitive to material softening at elevated temperatures, geometric nonlinearities, and variations in measured lamina thermal properties. To improve the accuracy of the residual deformation analysis, these results suggest that the thermo-chemical shrinkages preceding the cooldown should be considered, as well as possible variations in ply level microstructure due to the presence of the embedded fiber tow gaps and overlaps.

Composites↗

NASA NTRSDate not supplied

Computer Aided Process Planning for Automated Fiber Placement

Explore the source record for details and available documents.

AFP↗

NASA NTRSDate not supplied

Thermal Modelling of the in-Situ Consolidation of Automated Fiber Placement of Thermoplastic Composites

NASA is developing carbon fiber reinforced thermoplastic composites processing methods under the Hi-rate Composites Aircraft Manufacturing (HiCAM) project. The in-situ consolidation automated fiber placement (AFP) of thermoplastics (ICAT) process has high potential to increase manufacturing throughput and lower costs as it combines the repeatability and fast lay down rates of AFP with the thermoformability of thermoplastic materials to achieve part consolidation out of the autoclave. Physics-based process models are employed in the ICAT process development to understand, fundamentally, the thermal response of the carbon fiber (CF)/polyaryletherketone (PAEK) material during the rapid heating and cooling associated with laser-assisted AFP. A one-dimensional (1-D) closed-form model was developed capable of predicting the temperature profile through-the-thickness of the tape material. In addition, a two-dimensional (2-D) model was developed to predict the heat transfer through-the-thickness and in the laydown x-direction of the AFP head motion. The solution of the Fourier heat-transfer equations in the 2-D model is approximated using the explicit finite difference numerical method. The temperature profile during placement of PAEK slit-tape materials at various laser target temperatures and placement speeds were measured during ICAT process development trials at Electroimpact®, Inc. †† and the resulting experimental data is compared with the predictions of the 1-D and 2-D models.

Thermoplastics↗

NASA NTRSDate not supplied

Integration of Design Data Into Automated Fiber Placement Process Planning Metrics

With the ever-expanding aviation industry, a need is arising for more rapid production of composite aircraft to meet increasing demand. State-of-the-art aircraft such as the Boeing 787showcase 50% composite material usage by weight, highlighting this emerging industry-wide adoption of the material system. Currently, many of the large structures associated with these aircraft are manufactured additively via Automated Fiber Placement (AFP). The AFP process shows great potential for efficient manufacturing, however unavoidable defects still occur because of tool surface geometry, placement errors, or poor process planning, resulting in decreased quality and throughput. Due to such effects, it is critical to incorporate design for manufacturing (DFM) principles to achieve the optimal manufacturing plan and resulting structure. This work will develop a methodology for incorporating design information into process planning metrics in an automated fashion to achieve an optimal set of process inputs.The analysis incorporates HyperX, Computer Aided Process Planning (CAPP) and Vericut Composite Programming (VCP). Safety margins from HyperX are imported into CAPP where AFP defects are mapped to the values. The resulting margins are then incorporated into the CAPP manufacturability algorithms, creating a design informed process planning analysis

Automated Fiber Placement↗

NASA NTRSDate not supplied

In-Situ Consolidation Automated Fiber Placement of Thermoplastic Composites for High-Rate Aircraft Manufacturing

The National Aeronautics and Space Administration (NASA) initiated the Hi-Rate Composites Aircraft Manufacturing (HiCAM) project in 2021 with the goal of significantly increasing composite structures manufacturing rate in the commercial aircraft industry. The technologies currently under investigation include resin infusion and automated fiber placement (AFP) of novel thermoset materials and thermoplastic composites. Thermoplastic composites offer attractive solutions to rapid manufacturing due to their ability to be formed and consolidated quickly. NASA is particularly focused on assessing composite structure manufacturing utilizing an in-situ consolidation AFP of thermoplastics (ICAT) process employing a recently developed laser heating system. Two semi-crystalline polyaryletherketone thermoplastic tape materials were characterized to ascertain the ICAT process parameters at AFP placement speeds approaching 423 mm/s. The required laser power settings were determined at Electroimpact, measuring material temperatures utilizing a forward looking infrared (FLIR) thermal imaging camera and thermocouples. The material temperature, tool temperature, and placement speed were varied for resulting consolidation quality assessment. The resulting temperature data were also utilized to calibrate thermal analysis models under development at NASA. The experimental temperature data confirmed analytical results. An overview of the HiCAM project as well as initial data from ICAT process characterizations are described.

thermoplastic composites↗

NASA NTRS2022

In-Situ Consolidation Automated Fiber Placement of Thermoplastic Composites for High-Rate Aircraft Manufacturing

The National Aeronautics and Space Administration (NASA) initiated the Hi-Rate Composites Aircraft Manufacturing (HiCAM) project in 2021 with the goal of significantly increasing composite structures manufacturing rate in the commercial aircraft industry. The technologies currently under investigation include resin infusion and automated fiber placement (AFP) of novel thermoset materials and thermoplastic composites. Thermoplastic composites offer attractive solutions to rapid manufacturing due to their ability to be formed and consolidated quickly. NASA is particularly focused on assessing composite structure manufacturing utilizing an in-situ consolidation AFP of thermoplastics (ICAT) process employing a recently developed laser heating system. Two semi-crystalline polyaryletherketone thermoplastic tape materials were characterized to ascertain the ICAT process parameters at AFP placement speeds approaching 423 mm/s. The required laser power settings were determined at Electroimpact, measuring material temperatures utilizing a forward looking infrared (FLIR) thermal imaging camera and thermocouples. The material temperature, tool temperature, and placement speed were varied for resulting consolidation quality assessment. The resulting temperature data were also utilized to calibrate thermal analysis models under development at NASA. The experimental temperature data confirmed analytical results. An overview of the HiCAM project as well as initial data from ICAT process characterizations are described.

laser heating↗

NASA NTRSDate not supplied

Composites From in-Situ Consolidation Automated Fiber Placement of Thermoplastics for High-Rate Aircraft Manufacturing

The National Aeronautics and Space Administration (NASA) project Hi-Rate Composites Aircraft Manufacturing (HiCAM) aims to significantly increase commercial aircraft composite structures manufacturing rate. Thermoplastic composites offer attractive solutions to rapid manufacturing due to their ability to be formed and consolidated quickly. NASA has a particular interest in assessing composite structure manufacturing utilizing an in-situ consolidation automated fiber placement (AFP) of thermoplastics (ICAT) process employing current state-of-the-art laser heating systems. Three semi-crystalline polyaryletherketone (PAEK) thermoplastic tape materials were characterized to ascertain the ICAT process parameters. The required laser power settings were determined at Electroimpact, Inc., measuring material temperatures utilizing a forward looking infrared (FLIR) thermal imaging camera and thermocouples. The material temperature, tool temperature, and placement speed were varied for resulting consolidation quality assessment. The resulting temperature data were also utilized to calibrate thermal analysis models under development at NASA. The experimental temperature data confirmed analytical results. The quality of the resulting test panels was evaluated by both non-destructive evaluation as well as destructively by photo-microscopy. The effect on interlaminar strength was determined by short beam strength testing. Test results of carbon fiber laminates fabricated by ICAT using polyetheretherketone (PEEK), polyetherketoneketone (PEKK), and low-melt polyaryletherketone (LM-PAEK) at various placement temperatures and placement speeds are presented.

thermoplastic composites↗

NASA NTRSDate not supplied

Implementation of Combinatorial Optimization Techniques for Automated Fiber Placement Through Thickness Defect Stack-Up Minimization

The Computer Aided Process Planning (CAPP) module was developed to facilitate and accelerate the process planning workflow for Automated Fiber Placement (AFP). CAPP assists process planners in identifying optimal starting point locations and layup strategies for each ply of a laminate. Ply optimization operates on measurement and scoring of geometry-based defects such as gaps, overlaps, angle deviation, and steering. This paper expands on the established framework for analyzing defect stack-up through thickness of a laminate. Four different combinatorial optimization algorithms are implemented and evaluated: (1) genetic algorithm, (2) differential evolution, (3) particle swarm, and (4) greedy search. The algorithms identify the optimal combination of ply-level layup strategies, by scoring potential laminates on defect stacking, using two different objective functions. A final optimization approach is also presented which trades some performance for a large gain in efficiency. These approaches are compared to a randomized combination using a complex tool surface in a virtual case study. The result is a streamlined methodology for comparing different laminate-level manufacturing strategies and minimizing the through thickness defect stack up.

CAPP↗

NASA NTRS2019

Automated Fiber Placement of Composite Wind Tunnel Blades: Process Planning and Manufacturing

The ability to accurately manufacture large complex shapes in a consistent and repeatable manner has led to Automated Fiber Placement (AFP) being the predominant mode of manufacturing for large composite aerospace structures today. Currently, AFP is being considered for medium- and small-scale parts. Composite wind tunnel blades have traditionally been fabricated by hand layup for pre-impregnated or dry fabrics with resin infusion. Though well proven, the traditional fabrication method is laborious and tedious, and hence expensive. The project described in this paper used the Integral Structural Assembly of Advanced Composites (ISAAC) facility at the NASA Langley Research Center to build a manufacturing demonstration unit (MDU) with a shape representative of a wind tunnel blade. This MDU is used to discuss tooling, process planning, and fabrication. Additionally, details of the generic manufacturing workflow are presented.

Harik, Ramy↗

NASA NTRSDate not supplied

Design for Manufacturing of Structures with Automated Fiber Placement via Integration of Analysis and Process Planning

Under the Design for Manufacturing (DFM) task in the NASA HiCAM program, significant process has been made towards establishing a fully automated optimization process that spans the structural analysis, design, and manufacturing process planning for Automated Fiber Placement (AFP) structures. Previous efforts in this area established the data formats and mapping processes needed to exchange data between disciplines. The software tools used in the framework are HyperX (structural optimization), CAPP (process planning), and VCP (AFP path generation). The work has culminated with automation of data exchanges and an optimization process that drives the three software toward convergence. Within this framework, HyperX is used to generate mass-optimum composite designs which are iterated with VCP and CAPP to improve manufacturability of the designs. As the ply manufacturing process is adjusted by CAPP and VCP, HyperX continually re-assesses the structural integrity of the part and makes adjustments to the laminate as needed. For example, the position of fiber steering and tow overlaps/gaps can necessitate changes to the laminate design. Once the design converges, the end result is a stack of plies that meets both structural and manufacturing requirements. This paper presents the details of the framework and demonstrations the automated process on several parts with significant double-curvature.

HiCAM↗

NASA NTRS2023

Automated Fiber Placement Through Thickness Defect Stacking Optimization

In its 2022 commercial market outlook, Boeing forecasted an 80% increase in the global fleet through 2041 compared to 2019 pre-pandemic levels. This sharp rise in demand will drive pressure onto airframe manufacturers to ramp up production and find more efficient ways to design and manufacture airplanes. Complicating this challenge is the industry’s recent transformation from traditional metal-based airframes towards hybrid composite-metal aircraft. While composites have been used in aviation for decades, aircraft manufacturers are still struggling to design and manufacture quality parts at a high rate. Automated Fiber Placement (AFP) is one of the main manufacturing techniques used to produce large-scale composite parts. After a design has been created, a manufacturing strategy has to be developed based on the working material, part geometry, and machine capabilities. This process planning stage is essential to the AFP workflow and currently requires a high level of manual input from an experienced process planner. In an effort to automate and optimize this stage, the Computer Aided Process Planning (CAPP) module was developed. CAPP assists process planners in identifying optimal starting point location and layup strategy for each ply of a laminate. This Ply-Level Optimization (PLO) phase operates on the quantification of ply quality through predictable geometry-based defects such as gaps, overlaps, angle deviation, and steering. As you move from PLO to Laminate-Level Optimization (LLO) the design space grows exponentially, emphasizing the need for automated optimization. The work presented in this thesis expands CAPP’s functionality by comparing the planned fiber paths through the thickness of the laminate to mitigate stacked area defects and achieve an optimal laminate-level manufacturing strategy. Within CAPP, predicted gap and overlap defects are imported from Vericut Composites Programming (VCP) and then discretized to streamline the through-thickness comparison. Two objective functions are used to score different combinations of ply layup strategies based on defect stacking both globally and locally. Four combinatorial optimization algorithms were coupled with these objective functions to investigate the laminate-level manufacturing strategy design space and converge on the optimal plan. These algorithms were evaluated based on accuracy and efficiency through virtual testing on a complex tool surface. A separate LLO approach was developed to achieve near-optimal laminates in significantly less time. The end result is a software package which greatly reduces the required input from process planners, shortening the design-build cycle time and improving part quality.

AFP↗

NASA NTRSDate not supplied

Exploration and Manufacturing with Automated Fiber Placement

Highly repeatable and nearly defect-free fabrication of composite parts is critical to the success and widespread acceptance of composite materials. Through optimization using thin-ply materials, composite parts can be manufactured to be lighter and tailored more specifically to anticipated design loads than with standard prepreg materials alone. However, defects arising from the thin-ply manufacturing process are not always similar to defects found with standard tows. These new defects warrant evaluation. At NASA Langley Research Center, the manufacturing process parameters associated with automated fiber placement (AFP), a slit tape-based composite manufacturing process, were optimized for the use of a thin-ply prepreg carbon-epoxy material. Carbon-epoxy tows with areal weights of 30 g/m2 and 70 g/m2 were used in these manufacturing trials. The AFP process parameters of heater output, compaction force, tow feed rate, and tow tension were adjusted and optimized for successful manufacturing. This article documents an exploration of thin-ply fabrication on both flat and complex-shaped surfaces. Ultimately, aerospace-quality laminates were made from the 70-g/m2 material, but imperfections in the 30-g/m2 material itself and the fact that the AFP machine was not designed for such a thin material meant that more research and trials are required to obtain flight-quality 30-g/m2 laminates.

carbon-epoxy↗

NASA NTRSDate not supplied

Thin-Ply: Exploration and Manufacturing with Automated Fiber Placement

Abstract Highly repeatable and nearly defect-free fabrication of composite parts is critical to the success and widespread acceptance of composite materials. Through optimization using thin-ply materials, composite parts can be manufactured to be lighter and tailored more specifically to anticipated design loads than with standard prepreg materials alone. However, defects arising from the thin-ply manufacturing process are not always similar to defects found with standard tows. These new defects warrant evaluation. At NASA Langley Research Center, the manufacturing process parameters associated with automated fiber placement (AFP), a slit tape-based composite manufacturing process, were optimized for the use of a thin-ply prepreg carbon-epoxy material. Carbon-epoxy tows with areal weights of 30 g/m2 and 70 g/m2 were used in these manufacturing trials. The AFP process parameters of heater output, compaction force, tow feed rate, and tow tension were adjusted and optimized for successful manufacturing. This article documents an exploration of thin-ply fabrication on both flat and complex-shaped surfaces. Ultimately, aerospace-quality laminates were made from the 70-g/m2 material, but imperfections in the 30-g/m2 material itself and the fact that the AFP machine was not designed for such a thin material meant that more research and trials are required to obtain flight-quality 30-g/m2 laminates.

Carbon-expoxy↗