Search NASA⌕ Search

SEARCH · Search NASA

Results for “axial relocation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

27 records · Page 2

Anisotropic compression of a synthetic potassium aluminogermanate zeolite with gismondine topology

Compression behavior of a potassium aluminogermanate with a gismondine framework topology (K-AlGe-GIS) was studied using in-situ high-pressure synchrotron X-ray powder diffraction. In contrast to the potassium gallosilicate analogue (K-GaSi-GIS), no elastic anomaly due to pressure-induced hydration and/or cation relocation was observed in K-AlGe-GIS. The Birch-Murnaghan fit to the pressure-volume data results in a bulk modulus of B{sub 0} = 31(1) GPa. The derived linear-axial compressibilities (i.e., {beta}{sub a} = 0.0065(5) GPa{sup -1}, {beta}{sub b} = 0.0196(4) GPa{sup -1}, {beta}{sub c} = 0.0081(7) GPa{sup -1}) indicate that the b-axis, normal to the 8-ring channels, is about three times more compressible than the a and c axes, parallel to the elliptical 8-ring channels. As a consequence a gradual flattening of the so-called 'double crankshaft' structural building units of the gismondine framework is observed. In K-AlGe-GIS, this flattening occurs almost linear with pressure, whereas it is nonlinear in the GaSi-analogue due to structural changes of the water-cation assembly under hydrostatic pressures.

43 PARTICLE ACCELERATORS↗

Optimization of a dry, mixed nuclear fuel storage array for nuclear criticality safety - 14339

A dry storage array of used nuclear fuel at the Idaho National Laboratory contains a mixture of more than twenty different types of research and test reactor fuels. Significant neutronic interaction occurs between fuel canisters within this large storage arrangement of 636 fuel storage canisters. Nuclear criticality safety is maintained primarily by moderation control and through control of neutron interaction and leakage provided by the credited geometry. Over the nearly forty years of operation the collected fuels are now arranged in a configuration that does not minimize the system neutron multiplication factor (k{sub eff}). This creates a concern since the entire remaining facility storage capacity cannot be utilized without exceeding the system minimum subcritical state (k{sub safe}) for ensuring nuclear criticality safety. This work determines a more optimal arrangement for the stored fuels with a goal to minimize the system k{sub eff}, but also with a minimum of potential fuel canister relocation movements. The ultimate goal is to establish a solution for this multiple-objective optimization problem by finding the Pareto Front for maximum k{sub eff} reduction versus the number of canister relocations. The process first required additional analysis of the array by Monte-Carlo neutron transport codes (specifically, MCNP) to gain a greater understanding of the interaction characteristics of the disparate fuel types. Some stored fuels are composed of primarily metallic and oxide components that provide very little inherent moderation, while other fuel types contain graphite or zirconium-hydride which can contribute a significant amount of moderation. These factors cause a complex relationship within a fuel arrangement with respect to thermal utilization and axial leakage probability. The new MCNP analysis was utilized to develop a simplified spreadsheet-based empirical model which simulates the array k{sub eff} result. This empirical model was benchmarked against additional MCNP calculations for various arrangements and then employed in the optimization analysis. A Tabu metaheuristic and stochastic approximation optimization was applied to the empirical model with the optimization function to minimize the array k{sub eff}. The optimization algorithm interrogated the empirical model to determine the optimal rearrangement for up to sixty canister movements. The Pareto Front was found, which shows that a limited number of canister relocation movements could allow the existing thirty-one empty array positions to be filled with common research reactor fuels while also yielding a reduction in the overall array k{sub eff} relative to the current arrangement. This will impart an improvement in the facility utilization while also offering an enhancement in the safety margin. The reduction in array reactivity has been confirmed by a final set of MCNP calculations with the proposed new arrangements. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Replacing Arginine 33 for Alanine in the Hemophore HasA from Pseudomonas aeruginosa Causes Closure of the H32 Loop in the Apo-Protein

Previous characterization of hemophores from Serratia marcescens (HasAs), Pseudomonas aeruginosa (HasAp), and Yersinia pestis (HasA yp ) showed that hemin binds between two loops, where it is axially coordinated by H32 and Y75. The Y75 loop is structurally conserved in all three hemophores and harbors conserved ligand Y75. The other loop contains H32 in HasAs and HasAp, but a noncoordinating Q32 in HasA yp . The H32 loop in apo-HasAs and apo-HasAp is in an open conformation, which places H32 about 30 Å from the hemin-binding site. Hence, hemin binding onto the Y75 loop of HasAs or HasAp triggers a large relocation of the H32 loop from an open- to a closed-loop conformation and enables coordination of the hemin-iron by H32. In comparison, the Q32 loop in apo-HasA yp is in the closed conformation, and hemin binding occurs with minimal reorganization and without coordinative interactions with the Q32 loop. Studies in crystallo and in solution have established that the open H32 loop in apo-HasAp and apo-HasAs is well structured and minimally affected by conformational dynamics. In this study we address the intriguing issue of the stability of the H32 loop in apo-HasAp and how hemin binding triggers its relocation. Specifically, we address this question with a combination of NMR spectroscopy, X-ray crystallography, and molecular dynamics simulations and find that R33 is critical to the stability of the open H32 loop. Replacing R33 with A causes the H32 loop in R33A apo-HasAp to adopt a conformation similar to that of holo-HasAp. Finally, stopped-flow absorption and resonance Raman analyses of hemin binding to apo-R33A HasAp indicate that the closed H32 loop slows down the insertion of the heme inside the binding pocket, presumably as it obstructs access to the hydrophobic platform on the Y75 loop, but accelerates the completion of the heme iron coordination.

59 BASIC BIOLOGICAL SCIENCES↗

Determination of Experimental Fuel Rod Parameters using 3D Modelling of PCMI with MPS Defect

An in-reactor experiment is being designed in order to validate the pellet-cladding mechanical interaction (PCMI) behavior of the BISON fuel performance code. The experimental parameters for the test rod being placed in the Halden Research Reactor are being determined using BISON simulations. The 3D model includes a missing pellet surface (MPS) defect to generate large local cladding deformations, which should be measureable after typical burnup times. The BISON fuel performance code is being developed at Idaho National Laboratory (INL) and is built on the Multiphysics Object-Oriented Simulation Environment (MOOSE) framework. BISON supports both 2D and 3D finite elements and solves the fully coupled equations for solid mechanics, heat conduction and species diffusion. A number of fuel performance effects are included using models for swelling, densification, creep, relocation and fission gas production & release. In addition, the mechanical and thermal contact between the fuel and cladding is explicitly modelled using a master-slave based contact algorithm. In order to accurately predict PCMI effects, the BISON code includes the relevant physics involved and provides a scalable and robust solution procedure. The depth of the proposed MPS defect is being varied in the BISON model to establish an optimum value for the experiment. The experiment will be interrupted approximately every 6 months to measure cladding radial deformation and provide data to validate BISON. The complete rodlet (~20 discrete pellets) is being simulated using a 180° half symmetry 3D model with MPS defects at two axial locations. In addition, annular pellets will be used at the top and bottom of the pellet stack to allow thermocouples within the rod to measure the fuel centerline temperature. Simulation results will be presented to illustrate the expected PCMI behavior and support the chosen experimental design parameters.

BISON↗

Analysis of Experimental Fuel Rod Parameters using 3D Modelling of PCMI with MPS Defect

An in-reactor experiment is being designed in order to validate the pellet-cladding mechanical interaction (PCMI) behavior of the BISON fuel performance code. The experimental parameters for the test rod being placed in the Halden Research Reactor are being determined using BISON simulations. The 3D model includes a missing pellet surface (MPS) defect to generate large local cladding deformations, which should be measureable after typical burnup times. The BISON fuel performance code is being developed at Idaho National Laboratory (INL) and is built on the Multiphysics Object-Oriented Simulation Environment (MOOSE) framework. BISON supports both 2D and 3D finite elements and solves the fully coupled equations for solid mechanics, heat conduction and species diffusion. A number of fuel performance effects are included using models for swelling, densification, creep, relocation and fission gas production & release. In addition, the mechanical and thermal contact between the fuel and cladding is explicitly modelled using a master-slave based contact algorithm. In order to accurately predict PCMI effects, the BISON code includes the relevant physics involved and provides a scalable and robust solution procedure. The depth of the proposed MPS defect is being varied in the BISON model to establish an optimum value for the experiment. The experiment will be interrupted approximately every 6 months to measure cladding radial deformation and provide data to validate BISON. The complete rodlet (~20 discrete pellets) is being simulated using a 180° half symmetry 3D model with MPS defects at two axial locations. In addition, annular pellets will be used at the top and bottom of the pellet stack to allow thermocouples within the rod to measure the fuel centerline temperature. Simulation results will be presented to illustrate the expected PCMI behavior and support the chosen experimental design parameters.

BISON↗

Performance of a neutralizer for electron bombardment thruster

Results of the SERT II flight indicate that the hollow cathode neutralizer not only represents a power and propellant weight penalty but can be a contributing cause to accelerator grid erosion. Tests with a 30-cm diameter thruster show that a neutralizer position of approximately 9 cm axially downstream of the accelerator grid and approximately 9 cm radially away from the outer edge of the accelerator grid and pointing parallel to the thruster axis provides the best overall performance. The estimated grid wear rate was less than 0.08 mm in 10,000 hours. The coupling voltage was approximately 17 volts at a neutralizer flow rate of 22 equivalent milliamperes of mercury and a beam current of 1.5 amperes. Neutralizer power was 31 watts and the effect of neutralizer flow on overall propellant utilization efficiency is a 1.2 percentage point reduction at a thruster utilization efficiency of 90 percent. The neutralizer position defined in tests with a 30 cm thruster was tested with a 15 cm SERT II thruster. When the neutralizer was relocated further downstream with this different orientation, accelerator impingement current due to neutralizer operation was reduced by approximately a factor of seven and was nearly independent of neutralizer operation.

Bechtel, R. T.↗

EGS Collab Experiment 1: In-situ observation of pre-, co- and post-seismic shear slip preceding hydraulic fracturing

Understanding the initiation and arrest of earthquakes is one of the long-standing challenges of seismology. Here we report on direct observations of borehole displacement by a meter-sized shear rupture induced by pressurization of metamorphic rock at 1.5 km depth. We observed the acceleration of sliding, followed by fast co-seismic slip and a transient afterslip phase. Total displacements were about 7, 5.5 and 9.5 micrometers, respectively for the observed pre-slip, co-seismic slip and afterslip. The observed pre-slip lasted about 0.4 seconds. Co-seismic slip was recorded by the 1 kHz displacement recording and a 12-component array of 3-C accelerometers sampled at 100 kHz. The observed afterslip is consistent with analytical models of arrest in a velocity-strengthening region and subsequent stress relaxation. The observed slip vector agrees with the activation of a bedding plane within the phyllite, which is corroborated by relocated seismic events that were observed during the later stages of the injection experiment. This submission includes the pressure and deformation data recorded by the SIMFIP probe during the first injection at the 164 ft (50 m) notch of borehole E1-I. The injection was performed on on 05/22/2018 as part of Experiment 1 of the EGS Collab project. This data accompanies a manuscript submitted to GRL, linked in this submission.

15 GEOTHERMAL ENERGY↗

NDCX-II, an Induction Linac for HEDP and IFE Research

The Heavy Ion Fusion Science Virtual National Laboratory in the USA is constructing a new Neutralized Drift Compression eXperiment (NDCX-II) at LBNL. This facility is being developed for high energy density physics and inertial fusion energy research. The 12 m long induction linac in NDCX-II will produce a Li{sup +} beam pulse, at energies of 1.2-3 MeV, to heat target material to the warm dense matter regime ({approx} 1 eV). By making use of special acceleration voltage waveforms, 2.5T solenoid focusing, and neutralized drift compression, 20 - 50 nC of beam charge from the ion source will be compressed longitudinally and radially to achieve a subnanosecond pulse length and mm-scale target spot size. The original Neutralized Drift Compression Experiment (NDCX-I) has successfully demonstrated simultaneous radial and longitudinal compression by imparting a velocity ramp to the ion beam, which then drifts in a neutralizing plasma to and through the final focussing solenoid and onto the target. At higher kinetic energy and current, NDCX-II will offer more than 100 times the peak energy fluence on target of NDCX-I. NDCX-II makes use of many parts from the decommissioned Advanced Test Accelerator (ATA) at LLNL. It includes 27 lattice periods between the injector and the neutralized drift compression section (Figure 1). There are 12 energized induction cells, 9 inactive cells which provide drift space, and 6 diagnostic cells which provide beam diagnostics and pumping. Custom pulsed power systems generate ramped waveforms for the first 7 induction cells, so as to quickly compress the beam from 600 ns at the injector down to 70 ns. After this compression, the high voltages of the ATA Blumleins are then used to rapidly add energy to the beam. The Blumleins were designed to match the ferrite core volt-seconds with pulses up to 250 kV and a fixed FWHM of 70 ns. The machine is limited to a pulse repetition rate of once every 20 seconds due to cooling requirements. The NDCX-II beam is highly space-charge dominated. The 1-D ASP code was used to synthesize high voltage waveform for acceleration, while the 3-D Warp particle-in-cell code was used for detailed design of the lattice. The Li{sup +} ion was chosen because its Bragg Peak energy (at {approx} 2 MeV) coincides with the NDCX-II beam energy. The 130 keV injector will have a 10.9 cm diameter ion source. Testing of small (0.64 cm diameter) lithium doped alumino-silicate ion sources has demonstrated the current density ({approx} 1 mA/cm{sup 2}) used in the design, with acceptable lifetime. A 7.6 cm diameter source has been successfully produced to verify that the coating method can be applied to such a large emitting area. The ion source will operate at {approx} 1275 C; thus a significant effort was made in the design to manage the 4 kW heating power and the associated cooling requirements. In modifying the ATA induction cells for NDCX-II, the low-field DC solenoids were replaced with 2.5 T pulsed solenoids. The beam pipe diameter was decreased in order to reduce the axial extent of the solenoid fringe fields and to make room for water cooling. In addition, an outer copper cylinder (water-cooled) was used to exclude the solenoid magnetic flux from the ferrite cores. Precise alignment is essential because the beam has a large energy spread due to the rapid pulse compression, such that misalignments lead to corkscrew deformation of the beam and reduced intensity at focus. A novel pulsed-wire measurement method is used to align the pulsed solenoid magnets. Alignment accuracy has been demonstrated to within 100 {micro}m of the induction cell axis. The neutralized drift compression region after the last induction cell is approximately 1.2 m long and includes ferroelectric plasma sources (FEPS) fabricated by PPPL similar to those successfully operating in NDCX-I. The 8-T final focus pulsed solenoid, filtered cathodic arc plasma sources (FCAPS), and target chamber from NDCX-I are to be relocated to NDCX-II. The NDCX-II project started in July 2009 and is expected to complete in fall of 2011. As future funds become available, additional induction cells and pulsed power systems will be added to increase the beam energy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Computational and Experimental Examination of Simulated Core Damage and Relocation Dynamics of a BWR Fuel Assembly - 16013

The Japan Atomic Energy Agency (JAEA) plans a large-scale test to evaluate damage and relocation behavior of Boiling Water Reactor (BWR) core materials consisting of fuel rods (zirconia as fuel simulant), channel boxes, control blade assemblies as well as lower core-support structures. Its purpose is to contribute to the understanding of the core material relocation behavior in the event of severe accidents with the BWR design conditions for which existing experimental database is quite limited. Prior to large-scale testing anticipated at JAEA in the future, JAEA desires preliminary investigations to examine melting test pieces, being composed of a mixture of zirconia and metals by a non-transferred thermal plasma heating system. The purpose of such tests is to verify the materials and test piece will be heated by plasma as a primary heat source to the target temperature of ca. 2900 K and to collect data about the relocation behavior of the high-temperature materials. This paper describes the first in a series of tests demonstrating the effective use of thermal plasma technology to recreate the dynamics of a typical fuel core bundle channel assembly section. Results from preliminary computational simulations of simplified fuel bundle assemblies are presented illustrating the effectiveness of a 150 kW, non transferred (NTR) configuration of a thermal plasma argon jet to heat the assembly within a highly-insulated containment vessel. An experimental test program using the computational analyses as a basis and a Phoenix Solutions Co (PSC) commercial model PT150, 150 kW plasma torch is described and the test results are presented illustrating the time versus temperature history of the fuel bundle assembly melting dynamics. Details on plasma operation are discussed including: power requirements, current flow, voltage levels achieved, argon gas flow rates, processing times and standoff distances of the torch discharge from the top of the fuel bundle assembly (achieved with remote control of the axial (vertical) translation of the torch within the containment processing chamber). Photos taken from the top of the processing chamber are presented illustrating the various phases of melting characteristics of the zircaloy-clad, zirconium oxide filled fuel tubes, all within a stainless steel tube bundle channel centered within an insulated zirconia crucible. Based on lessons learned from this initial test campaign, a brief discussion of the requirements and features of a follow-on Phase II test program is provided. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗