Search NASA⌕ Search

SEARCH · Search NASA

Results for “base bleeding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Digital integrated control of a Mach 2.5 mixed-compression supersonic inlet and an augmented mixed-flow turbofan engine

A digitally implemented integrated inlet-engine control system was designed and tested on a mixed-compression, axisymmetric, Mach 2.5, supersonic inlet with 45 percent internal supersonic area contraction and a TF30-P-3 augmented turbofan engine. The control matched engine airflow to available inlet airflow. By monitoring inlet terminal shock position and over-board bypass door command, the control adjusted engine speed so that in steady state, the shock would be at the desired location and the overboard bypass doors would be closed. During engine-induced transients, such as augmentor light-off and cutoff, the inlet operating point was momentarily changed to a more supercritical point to minimize unstarts. The digital control also provided automatic inlet restart. A variable inlet throat bleed control, based on throat Mach number, provided additional inlet stability margin.

Batterton, P. G.↗
NASA NTRS1995

Flow Coefficient Behavior for Boundary Layer Bleed Holes and Slots

An experimental investigation into the flow coefficient behavior for nine boundary layer bleed orifice configurations is reported. This test was conducted for the purposes of exploring boundary layer control through mass flow removal and does not address issues of stability bleed. Parametric data consist of bleed region flow coefficient as a function of Mach number, bleed plenum pressure, and bleed orifice geometry. Seven multiple hole configurations and two single slot configurations were tested over a supersonic Mach number range of 1.3 to 2.5 (nominal). Advantages gained by using multiple holes in a bleed region instead of a single spanwise slot are discussed and the issue of modeling an entire array of bleed orifices based on the performance of a single orifice is addressed. Preconditioning the flow approaching a 90 degree inclined (normal) hole configuration resulted in a significant improvement in the performance of the configuration. The same preconditioning caused only subtle changes in performance for a 20 degree inclined (slanted) configuration.

Willis, B. P.↗
NASA NTRSDate not supplied

Engine Cycle Comparison for Alternative Propellant Nuclear Thermal Propulsion Engines

A modular Nuclear Thermal Propulsion (NTP) engine modeling suite was coded in Simulink to analyze various engine cycle configurations and propellants. This model was validated and used for previous studies involving alternative propellants for NTP engines. The current study compared hydrogen-based NTP (H-NTP) with ammonia-based Alternative propellant NTP (A-NTP) engines with expander and bleed cycle configurations. Based on prior work, the bleed cycle configuration was modified to yield a feasible result. The assumption that was made was that the Testing Reference Design (TRD) reactor will be used for all cases and that the difference in fuel loading fractions will be enough to offset any differences in the neutronics caused by switching the propellant. This work provided and compared propellant state points throughout the cycles as well as the key performance parameters. The conclusion was that bleed cycles for H-NTP engines are advantageous over expander cycles in terms of maximum system pressure, cycle simplicity, and potentially engine mass. Conversely, expander cycles are more advantageous for A-NTP engines according to the same scope of parameters. Future work will analyze reactor designs that are different from the TRD and use neutronics software integrated with the X-NTP model to provide higher fidelity results.

Nuclear↗
NASA NTRS1996

Advanced liquid Oxygen (LO2) propellant conditioning concept testing

Extensive testing was performed on the promising L02 propellant conditioning concept of passive recirculation (no-bleed). Data from the project is being used to further anchor models in L02 conditioning behavior and broaden the data base of no-bleed and low-bleed conditioning. Data base expansion includes results from testing the limits of no-bleed and low-bleed conditioning with various configuration changes to the test facility and designed test article. Configuration changes include low velocity effects in the recirculation loop above the test article, test article internal constriction impacts, test article out-of-plane effects, impact from an actual Titan L02 pump attachment, feed duct slope effects, and up-leg booster effects. LN2 was used as the test fluid. The testing was conducted between July 1994 and January 1995 at the west test area of Marshall Space Flight Center. Data have shown that in most cases passive recirculation was demonstrated when the aforementioned limits were applied.

Hasting, J. H.↗
NASA NTRS1972

Pressure-probe assembly for wind tunnels

Rake mounting design reduces aerodynamic-surface discontinuities to a minimum when installed in boundary layer bleed area. Mounting base is not required and, because of simplicity, rake can be manufactured at low cost.

Warfield, R. L.↗
NASA NTRS1991

The effects of compressor seventh-stage bleed air extraction on performance of the F100-PW-220 afterburning turbofan engine

A study was conducted to determine the effects of seventh-stage compressor bleed on the performance of the F100 afterburning turbofan engine. The effects of bleed on thrust, specific fuel consumption, fan turbine inlet temperature, bleed total pressure, and bleed total temperature were obtained from the engine manufacturer's status deck computer simulation. These effects were determined for power settings of intermediate, partial afterburning, and maximum afterburning for Mach numbers between 0.6 and 2.2 and for altitudes of 30,000, 40,000, and 50,000 ft. It was found that thrust loss and specific fuel consumption increase were approximately linear functions of bleed flow and, based on a percent-thrust change basis, were approximately independent of power setting.

Evans, Alison B.↗
NASA NTRS1993

Four-Nozzle Benchmark Wind Tunnel Model USA Code Solutions for Simulation of Multiple Rocket Base Flow Recirculation at 145,000 Feet Altitude

Multiple rocket exhaust plume interactions at high altitudes can produce base flow recirculation with attendant alteration of the base pressure coefficient and increased base heating. A search for a good wind tunnel benchmark problem to check grid clustering technique and turbulence modeling turned up the experiment done at AEDC in 1961 by Goethert and Matz on a 4.25-in. diameter domed missile base model with four rocket nozzles. This wind tunnel model with varied external bleed air flow for the base flow wake produced measured p/p(sub ref) at the center of the base as high as 3.3 due to plume flow recirculation back onto the base. At that time in 1961, relatively inexpensive experimentation with air at gamma = 1.4 and nozzle A(sub e)/A of 10.6 and theta(sub n) = 7.55 deg with P(sub c) = 155 psia simulated a LO2/LH2 rocket exhaust plume with gamma = 1.20, A(sub e)/A of 78 and P(sub c) about 1,000 psia. An array of base pressure taps on the aft dome gave a clear measurement of the plume recirculation effects at p(infinity) = 4.76 psfa corresponding to 145,000 ft altitude. Our CFD computations of the flow field with direct comparison of computed-versus-measured base pressure distribution (across the dome) provide detailed information on velocities and particle traces as well eddy viscosity in the base and nozzle region. The solution was obtained using a six-zone mesh with 284,000 grid points for one quadrant taking advantage of symmetry. Results are compared using a zero-equation algebraic and a one-equation pointwise R(sub t) turbulence model (work in progress). Good agreement with the experimental pressure data was obtained with both; and this benchmark showed the importance of: (1) proper grid clustering and (2) proper choice of turbulence modeling for rocket plume problems/recirculation at high altitude.

Dougherty, N. S.↗
NASA NTRS1975

Shuttle LOX loading transient study. Task 2 milestone report. National space and technology laboratories (NSTL) LOX loading facility analysis

Transient thermodynamic analyses were made of the LOX loading system proposed for the space shuttle main propulsion test article (MPTA). This system is made up of a LOX replenish system and a main LOX line which include the barge tank, the lines, pumps, and valves between the barge and the orbiter (ORB) ground service equipment (GSE) interface, the MPTA fill system, the space shuttle main engine (SSME) chilldown bleed system, and the GSE vent system. System analyses include predictions of system performance sensitivity to operating sequence and LOX flowrate, temperature, and quality at the ORB/GSE interface. The transient thermodynamic conditions at the SSME feed line entrance, ET entrance (tank bottom), and the SSME bleed/GSE vent TEE are also included. The analyses are based on continuous SSME bleed flow during GSE facility chilldown.

Glasgow, V. L.↗
NASA NTRS1994

YAV-8B reaction control system bleed and control power usage in hover and transition

Using a calibrated Rolls-Royce Pegasus engine and existing aircraft instrumentation and pressure taps, total and individual nozzle reaction control system (RCS) bleed flow rates have been measured on a YAV-8B Harrier during typical short takeoff, transition, hover, and vertical landing maneuvers. RCS thrust forces were calculated from RCS nozzle total pressure measurements, and control power was determined from the moments produced by these thrusts and the aircraft's moments of inertia. These data document the characteristics of the YAV-8B RCS with its basic stability augmentation system (SAS) engaged. Advanced control system designs for the YAV-8B can be compared to the original SAS based on the total bleed use and the percentage of available bleed used. In addition, the peak and mean values of the bleed and control power data can be used for sizing the reaction controls for a future short takeoff and vertical landing (STOVL) aircraft.

Borchers, Paul F.↗
NASA NTRS1973

Control of exit velocity profile of an asymmetric annular diffuser using wall suction

An asymmetric annular diffuser equipped with wall bleed (suction) capability was tested for controllability of exit velocity profile. The diffuser area ratio was 3.2, and the length to inlet height ratio was 1.6. Results show that the diffuser radial exit velocity profile could be controlled from a hub peaked to a tip peaked form by selective use of bleed on the outer wall or on both diffuser walls. Based on these results, application of the diffuser bleed technique to gas turbine combustors may be possible. Diffuser bleed could be used to tailor the airflow distribution for optimizing combustor performance at a variety of operating conditions.

Juhasz, A. J.↗
NASA NTRS2002

Self-Recirculating Casing Treatment Concept for Enhanced Compressor Performance

A state-of-the-art CFD code (APNASA) was employed in a computationally based investigation of the impact of casing bleed and injection on the stability and performance of a moderate speed fan rotor wherein the stalling mass flow is controlled by tip flow field breakdown. The investigation was guided by observed trends in endwall flow characteristics (e.g., increasing endwall aerodynamic blockage) as stall is approached and based on the hypothesis that application of bleed or injection can mitigate these trends. The "best" bleed and injection configurations were then combined to yield a self-recirculating casing treatment concept. The results of this investigation yielded: 1) identification of the fluid mechanisms which precipitate stall of tip critical blade rows, and 2) an approach to recirculated casing treatment which results in increased compressor stall range with minimal or no loss in efficiency. Subsequent application of this approach to a high speed transonic rotor successfully yielded significant improvements in stall range with no loss in compressor efficiency.

Hathaway, Michael D.↗
NASA NTRSDate not supplied

Structure and Dynamics of Bleed-Controlled Impinging Shock/Turbulent-Boundary-Layer Interactions

Porous boundary-layer bleed is often employed to alleviate the detrimental effects of shock/turbulent-boundary-layer interactions (STBLI) in high-speed vehicles. However, outstanding questions remain on the underlying mechanisms through which bleed influences STBLI dynamics. This work addresses this knowledge gap by performing a scale-resolved Large-Eddy Simulation of an impinging STBLI controlled by discrete bleed holes. The simulation has a freestream Mach number of 2.5, an oblique shock generator angle of 8 degrees, and a Reynolds number based on the incoming momentum thickness of 2800. Bleed substantially reduces the separation size and upstream influence of the STBLI compared to the canonical, uncontrolled case. Consequently, the characteristic, low-frequency motion of STBLI-induced separation is mitigated, as revealed by wall-pressure spectra. Energy is shifted from the low frequency separation behavior to a higher-frequency signature caused by the bleed shocks and expansions. The scale-resolved simulations also reveal that these small, localized structures severely limit the turbulence production traditionally seen in the uncontrolled interaction.

computational fluid dynamics↗
NASA NTRSDate not supplied

Scoping of an Air Supply Configuration for AFC on a Commercial Transport Airplane High Lift System

A scoping study is being conducted on the air supply fora microjet-based active flow control (AFC) system on a twin-turbofan commercial transport airplane. Microjets provide circulation control using small surface-normal pneumatic jets located near the trailing edge of a lifting surface such as a wing or flap. When located on the pressure side of the lifting surface they increase the lift, and when located on the suction side they decrease lift. In this study, microjets are considered for installation in the flaps of the high-lift version of the Common ResearchModel (CRM-HL). Two different architectures to supply the air for the microjets are considered: (1) bleed air from the airplane’s auxiliary power unit (APU) plus ram air, and (2) engine fan bleed air plus ram air. A model based on the 1D compressible flow equations is applied to analyze the air supply system architectures and predict the microjet flow rate with the resulting airplane performance changes based on Reynolds-averaged Navier-Stokes modeling of microjets on the CRM-HL. The results of this scoping study are encouraging in that pressurized air from the APU or the engine fan can be used to entrain ram air and thereby increase the AFC mass flow rate to achieve effective lift control and airplane performance enhancement during takeoff and landing.

AATT↗
NASA NTRS2001

Highly Loaded Low Pressure Turbine (LPT)

The goal of this study is to evaluate aspirated and non-aspirated aerodynamics on highly loaded LPT design. The objective is to increase stage loading by 30 to 50 percent without loss of efficiency for an existing low pressure turbine design. A study conducted on a NASA highly loaded multistage fan drive turbine (NASA CR-1964) indicated that end-wall bleed at the hub is a more significant parameter compared to aspirated airfoil. Based on this study, a 3-stage LPT is redesigned to 2-stage LIT with and without end-wall bleed. Both aerodynamic design and mechanical design are completed. In addition to end-wall bleed, exit guide vanes are designed with aspirated airfoils to reduce the losses. The LPT is redesigned with all constraints necessary for practical application. The benefit of the high-performance, highly loaded LPT shows up in reduced stage and part count, reduced size and weight, and reduced cost.

Ortiz, Milt↗
NASA NTRS1999

Triboelectric Charging in Simulated Mars Environment

Triboelectric charging of nonconducting materials followed by sudden electrostatic discharge (ESD) can damage electronic equipment and become ignition hazard to combustible materials. Mars atmosphere has near zero humidity and therefore natural charge bleeding to surroundings is anticipated to be limited. Potential mitigation of ESD problems has been conjectured based upon strong extraterrestrial radiation on Mars compared to earth. A hypothesis was formulated that ESD problem is less significant in simulated Mars condition since strong radiation and presence of argon will generate an ionized environment; this will be conducive to rapid bleeding of static charge into the surroundings.

Lee, R.↗
NASA NTRS1992

Three-dimensional shock-wave/boundary-layer interactions with bleed through a circular hole

Computations were performed to study three-dimensional (3-D), shock-wave/boundary-layer interactions on a flat plate in which fluid in the boundary layer was bled through a circular hole into a plenum to control shock-wave induced separation. Results are presented which show the details of the 3-D flowfield about the bleed hole and how bleed-hole placement relative to shock-wave impingement affect upstream, spanwise, and downstream influence lengths. This study revealed an underlying mechanisms by which bleed holes can affect shock-wave/boundary-layer interactions. This investigation is based on the ensemble-averaged, "full-compressible" Navier-Stokes equations closed by the Baldwin-Lomax turbulence model. Solutions to these equations were obtained by an implicit finite-volume method based on the partially-split, two-factored algorithm of Steger.

Rimlinger, M. J.↗
NASA NTRS2000

On Flowfield Periodicity in the NASA Transonic Flutter Cascade: Experimental Study - Part 1

An extensive study to improve flow uniformity and periodicity in the NASA Transonic Flutter Cascade is presented here. The results are reported in two independent parts dealing with the experimental approach and the analytical approach. The first part, the Experimental Study, focuses first on the data sets acquired in this facility in the past and explains several discrepancies, particularly the questions of actual flow incidence and cascade back pressure levels. Next, available means for control and modifications of the cascade flowfield, boundary layer bleed and tailboard settings are presented in detail. This is followed by experimental data sets acquired in modified test facility configurations that were based on analytical predictions of the cascade flowfield. Finally, several important conclusions about improving the cascade flowfield uniformity and blade load periodicity are summarized. The important conclusions are: (1) boundary layer bleed does not improve the cascade flow periodicity; (2) tunnel wall contours must be carefully matched to the expected shape of cascade streamlines; (3) actual flow incidence for each cascade configuration rather must be measured instead of relying on the tunnel geometry; and (4) the current cascade configuration exhibits a very high blade load uniformity over six blades from blade #2 to blade #7, and the facility is now ready for unsteady pressure data acquisition.

Lepicovsky, J.↗
NASA NTRS2010

Blended Training for Combat Medics

Bleeding from extremity wounds is the number one cause of preventable death on the battlefield and current research stresses the importance of training in preparing every Soldier to use tourniquets. HapMed is designed to provide tourniquet application training to combat medics and Soldiers using a blended training solution encompassing information, demonstration, practice, and feedback. The system combines an instrumented manikin arm, PDA, and computer. The manikin arm provides several training options including stand-alone, hands-on skills training in which soldiers can experience the actual torque required to staunch bleeding from an extremity wound and be timed on tourniquet application. This is more realistic than using a block of wood to act as a limb, which is often how training is conducted today. Combining the manikin arm with the PDA allows instructors to provide scenario based training. In a classroom or field setting, an instructor can specify wound variables such as location, casualty size, and whether the wound is a tough bleed. The PDA also allows more detailed feedback to be provided. Finally, combining the manikin arm with game-based technologies, the third component, provides opportunities to build knowledge and to practice battlefield decision making. Not only do soldiers learn how to apply a tourniquet, but when to apply a tourniquet in combat. The purpose of the paper is to describe the learning science underlying the design of HapMed, illustrate the training system and ways it is being expanded to encompass other critical life-saving tasks, and report on feedback received from instructors and trainees at military training and simulation centers.

Fowlkes, Jennifer↗