Search NASA⌕ Search

SEARCH · Search NASA

Results for “binder jet additive manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

The Influence of Printing Parameters, Post-Processing, and Testing Conditions on the Properties of Binder Jetting Additive Manufactured Functional Ceramics

This article outlines the current state-of-the-art binder jetting (BJT) additive manufacturing of functional ceramics. The impact of printing parameters, heat treatment processing, and testing conditions on the observed performance of these ceramics is discussed. Additionally, this article discusses the impact of physical properties such as density and mechanical strength on the overall performance of these functional ceramics. Although printing parameters and initial feedstock are crucial for the printability of the desired parts, other factors play an important role in the performance of the ceramic. Thermal post-processing is crucial to achieve optimized functional properties, while the testing orientation is key to obtaining the maximum output from the part. Finally, future research directions for this field are also discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Binder jetting additive manufacturing of silicon carbide ceramics: Development of bimodal powder feedstocks by modeling and experimental methods

A limitation of binder jetting additive manufacturing is the low density of fabricated parts. Mixing powders with different sizes is a promising approach to increase powder bed packing density and, hence, printed part density. However, in previous studies mixed powder feedstock was prepared by trial and error method. In this research, both modeling and experimental methods were used to prepare the bimodal powder feedstocks. Analytical packing model was introduced for irregular powders. A bimodal powder was prepared by mixing two different-sized silicon carbide powders (i.e. coarse and fine) using ball mill, and their tap densities were measured. Silicon carbide plates were printed using the coarse and bimodal powders by a commercial binder jetting system. Results showed that the modeling method could predict the tap density of bimodal powders with high accuracy. The printed parts from bimodal powder achieved higher green densities than those from the unimodal powder.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructure evolution during binder jet additive manufacturing of H13 tool steel

H13 is one of the most used tool steels for both hot and cold work tooling applications. Binder jet additive manufacturing offers the potential to deposit complex tools at scale due to larger powder bed sizes and faster deposition rates. However, to date there is no published literature on the sintering of H13 to full densification. Here, we discuss the pressureless sintering of binder jet AM H13 steel to full densification via supersolidus liquid phase sintering (SLPS) while presenting appropriate process windows (1360 °C – 1380 °C) for densification without distortion. The process windows have been rationalized based on thermodynamic calculations of liquid volume fractions with temperature. We show that higher binder saturation results in higher carbon retention and subsequently early liquid formation that can initiate the sintering process at lower temperatures. We report abnormal grain growth during sintering and found that the solidification phase transformations play a critical role on microstructural evolution and must be considered to accurately model the kinetics of SLPS.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Optimization of overhang printing in ceramic binder jetting additive manufacturing

Cylindrical-shaped horizontally-hanging overhangs with different heights on a solid cubic body were printed via binder jetting additive manufacturing with sililcon carbide powder feedstock. Cracking on the overhang neck and sagging on the overhang body were observed both pre- and post-curing, especially on printed design with a smaller particle size of 10 μm. Here, it was found that the width of cracking and depth of sagging were dependent on the height relative to the solid body in the powder bed, and elevated position of overhang with large volume of underneath loose powder led to increased extend of cracking and sagging. Overhang diameter and weight were varied, which were found with no apparent effects on its deformation extend. To mitigate cracking and sagging, contactless support was designed and tested, which could significantly improve the overhang stability and avoid any overhang deformations. Support gap and support distance were studied for their effects on support capability. The printing processes with and without contactless support were simulated by a finite element modeling approach to understand the stress distribution and evolution of the overhang structures, which revealed stress concentrations on the upper neck point of the designed overhang.

Binder jetting↗
DOE OSTI2024

Water Atomized H13 Tool Steel Powders for Binder Jet Additive Manufacturing

ORNL (Contractor) and Ametek, Inc. (Participant) collaborated to determine the feasibility of adopting water atomized H13 tool steel powder for binder jet additive manufacturing (BJAM) for tooling applications. The capability to utilize water atomized powders can substantially reduce powder expenses for BJAM, enabling process competitiveness with casting whilst enabling new applications of high-temperature, net-shaped components.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Exploration of Binder Jet Additive Manufacturing for Automotive Heat Sink Component Fabrication

ORNL (Contractor) and Magna Services of America Inc. (Participant) collaborated to determine the feasibility of binder jet additive manufacturing (BJAM) for the fabrication of copper components for automotive heat sink applications. This Phase 1 collaboration focused on printing copper heat sinks that rely on capillary effect to move fluids rather than mechanical pumps in electric vehicles to extend the battery range and life. Partial sintering of copper powders deposited via BJAM was hypothesized to aid capillary effect to improve the heat transfer. Further, BJAM offers the potential for scalability at a production level.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Spray coating for washout tooling by binder jet additive manufacturing

We report washout tooling is a process in which a removable mold or fixture is disintegrated using a solvent. Binder Jet (BJ) additive manufacturing holds promise for creating customized washout molds from common materials. BJ-based washout tooling provides an advanced strategy in manufacturing fiber-reinforced composites (FRCs), especially for customized hollow FRCs. However, washout tools formed by BJ require an impermeable barrier between the porous tooling surface and the parts laid up on the surface to prevent the resin from infiltrating the tooling surface and bonding the tool to the FRC. The conventional method for preventing resin migration into the washout mold from the FRC is winding Teflon® tape over the entire surface, which is labor-intensive and very difficult to deploy for specific geometries. Here, we report the development of a polymer spray coating method to seal the tooling surface and prevent resin infiltration without affecting the washout properties needed for sacrificial tooling. Two water-soluble polymers, poly(sodium 4-styrenesulfonate) (PSS–Na) and poly(vinylsulfonic acid, sodium salt) (PVS–Na), were investigated for spray coating. PVS-Na maintained tighter geometric tolerances and provided excellent thermal stability with the onset of decomposition at 320 °C and glass transition temperature of 280 °C. Spray coating with PVS-Na streamlines the process of forming a protective layer for the washout molds by BJ, reduces migration of the resins from the FRC, and significantly improves the production efficiency of complex washout tools.

42 ENGINEERING↗
DOE OSTI2020

Metal Powder Recyclability in Binder Jet Additive Manufacturing

The recyclability of 316L stainless steel powder in the binder jetting process has been determined. The powder characterization results demonstrated a 22% increase in the number of coarse particles (> 30 µm) and an 18.2% reduction in the number of small particles (< 10 µm) after recycling up to 16 times. A few elongated and irregular-shaped particles were found after recycling, possibly due to particle agglomeration during handling and sieving. Here, a negligible increase in the oxygen content by 0.036% was detected in the recycled powder. The density of sintered parts produced using recycled powder was approximately 1.5% lower than when using fresh powder due to the changes in the particle size distribution and the flowability of the powder caused by the changes in morphology. Final parts built using fresh and recycled powder showed similar hardness (155 ± 3 HV and 165 ± 9 HV) and yield strength (206 ± 16 MPa and 192 ± 10 MPa), respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Binder jet additive manufacturing of ceramic heat exchangers for concentrating solar power applications with thermal energy storage in molten chlorides

Triply periodic minimal surface (TPMS) geometries can only be fabricated by additive manufacturing methods and are of interest for heat exchangers. Ceramic TPMS heat exchangers can operate at higher temperatures and pressures with superior performance and increased operating efficiencies compared to metal heat exchangers. The properties of ultra-high temperature ceramic (UHTC) materials are also favorable for heat exchangers and potentially suited to concentrated solar power (CSP) systems, such as those based on a molten chloride salt thermal energy storage (TES) medium used to heat CO 2 in a closed-loop Brayton power cycle. We intended to demonstrate binder jet additive manufacturing feasibility of a UHTC-TPMS structure by printing and sintering a null candidate. We aimed to achieve parts with a relative density ≥ 92 % of theoretical and to provide a TPMS part demonstration. The target density indicates the transition from intermediate to final stage sintering, a requirement to inhibit gas permeability and for sintering complex near net shapes to full density with sinter-HIP technology. The goal of the TPMS part demonstration was to determine if printing and sintering parameters developed from test coupons apply to the complex geometries that will eventually be used in a heat exchanger design. Our objective was to print cubic TPMS parts with a 9 cm 3 volume and sinter it without distorting and cracking. We report we were able to sinter ZrB 2 -MoSi 2 composite parts based on the Schwarz-D TPMS and achieve isotropic shrinkage up to 60 % by volume, resulting in densities ranging from 92 % to 96 % of theoretical.

36 MATERIALS SCIENCE↗
DOE OSTI2020

An in-situ crosslinking binder for binder jet additive manufacturing

Additive Manufacturing (AM) of metals is a potentially disruptive technology that could significantly change the industrial supply chain. There are a limited number of AM methods capable of creating metal parts, and one method showing significant potential is Binder Jet AM (Binder Jetting). Binder Jetting utilizes an inkjet print head to deposit a binder fluid onto a powder bed and bind together powder particles into a desired geometry. This study investigates a new binder system consisting of a difunctional monomer, triethylene glycol dimethacrylate (TEG-DMA). TEG-DMA exhibits excellent printability with an Ohnesorge’s number of .258 making the Z number 3.876. During the thermal curing process, the difunctional monomer polymerizes and crosslinks at the onset temperature of 138 °C, becoming a solid dimethacrylate network. When the binder is utilized within the stainless-steel powder bed at 200 °C, it forms a network incorporating the stainless-steel particles, binding the powder into any specified geometry. Crosslinking the monomer within the stainless-steel 420 powder bed imparts a flexural strength of 1.0–3.3 MPa to the green part depending on the volume of monomer in the part. After sintering, the final stainless-steel parts results in a void fraction close to 60 % and carbon content below 0.4 %.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Binder Jet-Metals

Additive manufacturing is a type of material shaping technology that has many advantages over traditional manufacturing. Binder jet additive manufacturing uses a powder feedstock and an inkjet printhead to shape metal powders into preforms that are then processed in a furnace to reach full density. Because of the high throughput and low cost of the process, binder jetting is growing in popularity among manufacturers, but challenges with the process in terms of densification of the bound preforms still exist. This article will provide an overview of the binder jetting process, contrast binder jetting with the better-known powder bed fusion additive manufacturing technologies, review the metal alloys that have been printed with binder jet and then processed to full density, and provide a path forward for processing lightweight metal powders shaped by binder jetting to full density.

Elliott, Amy↗
DOE OSTI2021

Binder Jet Printing of H13 Tool Steel

ORNL and Carpenter worked on evaluating H13 powders with different powder size distributions for deposition via binder jet additive manufacturing (AM). Binder jet AM has the potential to be a costeffective technique for fabrication of near net shaped tools with complex geometries and internal features such as cooling channels that can improve the production efficiency of injection/compression molding tools. However, a critical challenge in binder jet AM is the densification of the said tool for it to be usable. Powder size distribution can affect the process settings required to deposit the material and the subsequent sintering behavior. In this collaborative effort ORNL and Carpenter demonstrated that the process variables depend on the powder size distribution while the carbon pickup during sintering depends on the binder burnout atmosphere and temperature. On the other hand, there was no noticeable difference in the microstructural evolution of H13 deposited using the different powder size distributions.

42 ENGINEERING↗
DOE OSTI2024

Surface Finishing and Coating Parameters Impact on Additively Manufactured Binder-Jetted Steel–Bronze Composites

In this paper, electroless nickel plating is explored for the protection of binder-jetting-based additively manufactured (AM) composite materials. Electroless nickel plating was attempted on binder-jetted composites composed of stainless steel and bronze, resulting in differences in the physicochemical properties. We investigated the impact of surface finishing, plating solution chemistry, and plating parameters to attain a wide range of surface morphologies and roughness levels. We employed the Keyence microscope to quantitatively evaluate dramatically different surface properties before and after the coating of AM composites. Scanning electron microscopy revealed a wide range of microstructural properties in relation to each combination of surface finishing and coating parameters. We studied chempolishing, plasma cleaning, and organic cleaning as the surface preparation methods prior to coating. We found that surface preparation dictated the surface roughness. Taguchi statistical analysis was performed to investigate the relative strength of experimental factors and interconnectedness among process parameters to attain optimum coating qualities. The quantitative impacts of phosphorous level, temperature, surface preparation, and time factor on the roughness of the nickel-plated surface were 17.95%, 8.2%, 50.02%, and 13.21%, respectively. On the other hand, the quantitative impacts of phosphorous level, temperature, surface preparation, and time factor on the thickness of nickel plating were 35.12%, 41.40%, 3.87%, and 18.24%, respectively. The optimum combination of the factors’ level projected the lowest roughness of Ra at 7.76 µm. The optimum combination of the factors’ level projected the maximum achievable thickness of ~149 µm. This paper provides insights into coating process for overcoming the sensitivity of AM composites in hazardous application spaces via robust coating.

36 MATERIALS SCIENCE↗
DOE OSTI2022

ADDITIVELY MANUFACTURED SURFACE HEAT TRANSFER ENHANCEMENTS FOR THE TRANSFORMATIONAL CHALLENGE REACTOR

The Transformational Challenge Reactor (TCR) is a high-temperature gas-cooled reactor design that uses additively manufactured fuel elements. TCR fuel elements have walls made of silicon carbide and are filled with tristructural-isotropic fuel particles. These fuel elements can have radically different shapes and integrated features than existing designs due to the reduced cost for complex structures in binder jet additive manufacturing. As such, binder jet additive manufacturing enables wall surface features to be embedded that can deliver superior heat transfer performance than smooth wall designs. In this work, the authors conducted a computational fluid dynamics study to evaluate selected wall features integrated into TCR fuel elements. Results show that surface features can outperform smooth wall designs; however, there are unique challenges for gas-cooled reactor core designs that have not been fully explored by previous research. For example, the rough surface finish and process variability of ceramics additive manufacturing make it challenging to predict surface roughness effects before fabrication. Additionally, the small hydraulic diameters of coolant channels in reactor cores make it difficult to engineer surface features that do not significantly increase the pressure drop. Engineers must carefully size surface features for heat transfer enhancement in additive fuel elements to operate above the base material's surface roughness effects and below the coolant channel size.

Weinmeister, Justin↗
DOE OSTI2022

Development of a silicon carbide ceramic based counter-flow heat exchanger by binder jetting and liquid silicon infiltration for concentrating solar power

A silicon carbide ceramic counter-flow heat exchanger with integrated headers was printed by binder jetting additive manufacturing process. Multiple phenolic binder infiltration cycles (3 or 5) followed by pyrolysis were conducted to increase the net carbon content of the printed SiC specimens. Subsequently, to attain full densification, silicon melt infiltration was used. The microstructure and mechanical properties were comprehensively characterized on the densified material. The chemical compositions and visual distribution of the various regions in the specimens were determined via scanning electron microscopy, while X-ray diffraction and synchrotron µ-computed tomography were used to provide a quantitative assessment of the volume fractions of the identified phase regions. Microhardness measurements showed dependence on the local microstructure. The fracture strength of the material was correlated with the specimen density and agreed with the reported values in the literature. High-temperature exposure at 750 °C for up to 200h did not degrade the strength for the specimens with three phenolic-binder infiltrations; however, the strengths degraded for ones with five phenolic-binder infiltrations. The associated fracture toughnesses of the specimens were ~3.4 MPam 1/2 at room temperature and 750°C, and the thermal conductivities varied from >150 W/mK at room temperature to ~45 W/mK at 750°C. Hence, this study validated the use of the binder-jetting printed SiC ceramic materials for high-temperature heat exchanges. Lastly, we also present in this work the first successful fabrication of a binder-jetting printed one-piece dense SiC ceramic heat exchanger body with unblocked channels that can be used for the flow of heat transfer fluids.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Robust Solar Receivers Using MAX Phase Materials

This work was supported by the U.S. Department of Energy’s Office of Energy Efficiency and Renewable Energy under the Solar Energy Technologies Office Award Number 35928. The objective of the proposed effort was to develop and optimize additive manufacturing technologies for low-cost fabrication of high-temperature receivers using MAX phase-based materials (Ti 3 SiC 2 and Ti 3 AlC 2 ). MAX phase materials are a group of ternary metal carbides and nitrides where M stands for an early transition metal element, A is a group 13–16 element, and X is C and/or N. In Phase 1, the binder jetting additive manufacturing process was used to synthesize and characterize the Ti 3 SiC 2 MAX phase material. The typical process involved first producing a TiC preform using binder jetting followed by infiltration of the preform with silicon melt to form Ti 3 SiC 2 in situ. The reaction-infiltrated samples showed formation of MAX phase in the sample core; however, the surface showed cracking. Various process conditions—cooling rates, hold times, Si proportion, etc.—were varied to minimize the surface cracking. The fabricated MAX phase core was characterized by microstructure analysis and evaluations of mechanical properties such as hardness and thermal shock. In Phase 2, the focus included fabrication of Ti 3 SiC 2 MAX phase materials by spark plasma sintering (SPS) and synthesis of Ti 3 AlC 2 MAX phase materials by the Al melt infiltration process. It is expected that Al infiltration will not cause sample cracking, since Al does not expand during solidification. In addition, other processing approaches were investigated to fabricate the MAX phase materials, such as SPS with a graphite bedding approach for producing short-length Ti 3 AlC 2 MAX phase tubes for demonstration of prototypical Concentrating Solar Power receiver tubes. Fabricated samples underwent thermo-mechanical testing to validate the materials for the solar receiver application at temperatures >1000°C. In Phase 3, the effort focused on the development and optimization of the Ti-Al-C MAX phase composite material using the Al melt infiltration approach. We started with optimization of precursor powders and making preform structures by either pressing them in a die or using the binder jetting additive manufacturing process followed by Al melt infiltration. In addition, we investigated the formation of preform structures by cold isostatic pressing followed by Al melt infiltration for making Ti-Al-C MAX phase composite. Thermo-mechanical characterizations, such as creep, strength, and thermal shock, were conducted to establish the structures’ performance.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Additive manufacturing of strong silica sand structures enabled by polyethyleneimine binder

Abstract Binder Jet Additive Manufacturing (BJAM) is a versatile AM technique that can form parts from a variety of powdered materials including metals, ceramics, and polymers. BJAM utilizes inkjet printing to selectively bind these powder particles together to form complex geometries. Adoption of BJAM has been limited due to its inability to form strong green parts using conventional binders. We report the discovery of a versatile polyethyleneimine (PEI) binder for silica sand that doubled the flexural strength of parts to 6.28 MPa compared with that of the conventional binder, making it stronger than unreinforced concrete (~4.5 MPa) in flexural loading. Furthermore, we demonstrate that PEI in the printed parts can be reacted with ethyl cyanoacrylate through a secondary infiltration, resulting in an increase in flexural strength to 52.7 MPa. The strong printed parts coupled with the ability for sacrificial washout presents potential to revolutionize AM in various applications including construction and tooling.

36 MATERIALS SCIENCE↗