Search NASA⌕ Search

SEARCH · Search NASA

Results for “brittle materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Fracture toughness of brittle materials determined with chevron notch specimens

The use of chevron-notch specimens for determining the plane strain fracture toughness (K sub Ic) of brittle materials is discussed. Three chevron-notch specimens were investigated: short bar, short rod, and four-point-bend. The dimensionless stress intensity coefficient used in computing K sub Ic is derived for the short bar specimen from the superposition of ligament-dependent and ligament-independent solutions for the straight through crack, and also from experimental compliance calibrations. Coefficients for the four-point-bend specimen were developed by the same superposition procedure, and with additional refinement using the slice model of Bluhm. Short rod specimen stress intensity coefficients were determined only by experimental compliance calibration. Performance of the three chevron-notch specimens and their stress intensity factor relations were evaluated by tests on hot-pressed silicon nitride and sintered aluminum oxide. Results obtained with the short bar and the four-point-bend specimens on silicon nitride are in good agreement and relatively free of specimen geometry and size effects within the range investigated. Results on aluminum oxide were affected by specimen size and chevron-notch geometry, believed due to a rising crack growth resistance curve for the material. Only the results for the short bar specimen are presented in detail.

Shannon, J. L., Jr.↗
NASA NTRS1980

Design with brittle materials - An interdisciplinary educational program

A series of interdisciplinary design courses being offered to senior and graduate engineering students at the University of Washington is described. Attention is given to the concepts and some of the details on group design projects that have been undertaken during the past two years. It is noted that ceramic materials normally demonstrate a large scatter in strength properties. As a consequence, when designing with these materials, the conventional 'mil standards' design stresses with acceptable margins of safety cannot by employed and the designer is forced to accept a probable number of failures in structures of a given brittle material. It is this prediction of the probability of failure for structures of given, well-characterized materials that forms the basis for this series of courses.

Mueller, J. I.↗
NASA NTRS1984

Methods for assessing the structural reliability of brittle materials

Failure from contact-induced surface flaws is considered along with controlled indentation flaws for construction of toughness and fatigue master maps, fatigue properties of ceramics with natural and controlled flaws, and a statistical analysis of size and stress state effects on the strength of an alumina ceramic. Attention is also given to dynamic and static fatigue of a machinable glass ceramic, the effect of multiregion crack growth on proof testing, and a fracture mechanics analysis of defect sizes. Other topics explored are related to the effect of temperature and humidity on delayed failure of optical glass fibers, subthreshold indentation flaws in the study of fatigue properties of ultrahigh-strength glass, the lifetime prediction for hot-pressed silicon nitride at high temperatures, static fatigue in high-performance ceramics, and requirements for flexure testing of brittle materials.

Freiman, S. W.↗
NASA NTRS2005

Life Predicted in a Probabilistic Design Space for Brittle Materials With Transient Loads

Analytical techniques have progressively become more sophisticated, and now we can consider the probabilistic nature of the entire space of random input variables on the lifetime reliability of brittle structures. This was demonstrated with NASA s CARES/Life (Ceramic Analysis and Reliability Evaluation of Structures/Life) code combined with the commercially available ANSYS/Probabilistic Design System (ANSYS/PDS), a probabilistic analysis tool that is an integral part of the ANSYS finite-element analysis program. ANSYS/PDS allows probabilistic loads, component geometry, and material properties to be considered in the finite-element analysis. CARES/Life predicts the time dependent probability of failure of brittle material structures under generalized thermomechanical loading--such as that found in a turbine engine hot-section. Glenn researchers coupled ANSYS/PDS with CARES/Life to assess the effects of the stochastic variables of component geometry, loading, and material properties on the predicted life of the component for fully transient thermomechanical loading and cyclic loading.

Nemeth, Noel N.↗
NASA NTRS1981

Fracture toughness of brittle materials determined with chevron notch specimens

Short bar, short rod, and four-point-bend chevron-notch specimens were used to determine the plane strain fracture toughness of hot-pressed silicon nitride and sintered aluminum oxide brittle ceramics. The unique advantages of this specimen type are: (1) the production of a sharp natural crack during the early stage of test loading, so that no precracking is required, and (2) the load passes through a maximum at a constant, material-independent crack length-to-width ratio for a specific geometry, so that no post-test crack measurement is required. The plane strain fracture toughness is proportional to the maximum test load and functions of the specimen geometry and elastic compliance. Although results obtained for silicon nitride are in good mutual agreement and relatively free of geometry and size effects, aluminum oxide results were affected in both these respects by the rising crack growth resistance curve of the material.

Shannon, J. L., Jr.↗
NASA NTRS1991

The sensitivity of fracture location distribution in brittle materials

The Weibull weak-link theory allows for the computation of distribution functions for both the fracture location and the applied far-field stress. Several authors have suggested using the fracture location information from tests to infer Weibull parameters, and others have used the predictive capabilities of the theory to calculate average fracture locations for brittle bodies. By a simple set of example calculations, it is shown that the fracture location distribution function is distinctly more sensitive to perturbations in the stress state than the fracture stress distribution function is. In general, the average fracture location is more subject to stress perturbations than the average fracture stress. The results indicate that care must be exercised in applying fracture location theory.

Wetherhold, Robert C.↗
NASA NTRS1970

Biaxial prestressing of brittle materials

Strengthening of chemically consolidated zirconia with tungsten fibers, graphite fibers, sapphire whiskers, and silicon carbide whiskers is investigated. Addition of silicon carbide whiskers gives the highest increase in strength of zirconia at room and elevated temperatures. Prestressing with tungsten cables increases tensile strength and ductility

Greszczuk, L.↗
NASA NTRS1982

Compliance calibration of the short rod chevron-notch specimen for fracture toughness testing of brittle materials

The short rod chevron-notch specimen has the advantages of (1) crack development at the chevron tip during the early stage of test loading, and (2) convenient calculation of plane-strain fracture toughness from the maximum test load and from a calibration factor which depends only on the specimen geometry and manner of loading. For generalized application, calibration of the specimen over a range of specimen proportions and chevron-notch configurations is necessary. Such was the objective of this investigation, wherein calibration of the short rod specimen was made by means of experimental compliance measurements converted into dimensionless stress intensity factor coefficients.

Bubsey, R. T.↗
NASA NTRS1989

Dynamic stress intensity factors of brittle materials

A new hybrid experimental-numerical procedure was used to characterize dynamic fracture response of structural ceramics at elevated temperature. The dynamic stress intensity factor (SIF) versus crack velocity relations of glass and reaction bonded silicon nitride (RBSN), are reviewed. The dynamic SIF versus crack velocity relations of alumina, TiB2-particulate/SiC-matrix composite and SiCw/Alumina-matrix composite are also presented. Available data indicated that dynamic arrest SIF was not observed in glass and monolithic ceramics, and suggested that further studies be conducted to resolve the existence or lack of existence of a dynamic arrest SIF in ceramic matrix composites.

Kobayashi, Albert S.↗
NASA NTRS1991

Comparison of Weibull strength parameters from flexure and spin tests of brittle materials

Fracture data from five series of four point bend tests of beam and spin tests of flat annular disks were reanalyzed. Silicon nitride and graphite were the test materials. The experimental fracture strengths of the disks were compared with the predicted strengths based on both volume flaw and surface flaw analyses of four point bend data. Volume flaw analysis resulted in a better correlation between disks and beams in three of the five test series than did surface flaw analysis. The Weibull (moduli) and characteristic gage strengths for the disks and beams were also compared. Differences in the experimental Weibull slopes were not statistically significant. It was shown that results from the beam tests can predict the fracture strength of rotating disks.

Holland, Frederic A., Jr.↗
NASA NTRS1990

Micromechanical model of crack growth in fiber reinforced brittle materials

A model based on the micromechanical mechanism of crack growth resistance in fiber reinforced ceramics is presented. The formulation of the model is based on a small scale geometry of a macrocrack with a bridging zone, the process zone, which governs the resistance mechanism. The effect of high toughness of the fibers in retardation of the crack advance, and the significance of the fiber pullout mechanism on the crack growth resistance, are reflected in this model. The model allows one to address issues such as influence of fiber spacing, fiber flexibility, and fiber matrix friction. Two approaches were used. One represents the fracture initiation and concentrated on the development of the first microcracks between fibers. An exact closed form solution was obtained for this case. The second case deals with the development of an array of microcracks between fibers forming the bridging zone. An implicit exact solution is formed for this case. In both cases, a discrete fiber distribution is incorporated into the solution.

Rubinstein, Asher A.↗