Search NASA⌕ Search

SEARCH · Search NASA

Results for “calcination temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

A Study on the Synthesis and Proton Transport Behavior of Multilayered ZSM-5 Zeolite Nanosheet Membranes Laminated on Polymer Substrates

Single crystalline ZSM-5 ZNs with thicknesses around 6 nm were obtained by secondary growth of silicalite nanoparticles using diquaternary bis-1,5(tripropyl ammonium) pentamethylene diiodide (dC5) as a structure-directing agent (SDA). The dC5 could be effectively removed from the ZN pores by either high-temperature calcination or UV irradiation in air at room temperature but not by the piranha solution treatment. Ultrathin ZN-laminated membranes (ZNLMs) were fabricated by sandwiching a UV-activated multilayered ZN film between two recast Nafion® layers (ZNLM-Nafion) and by filtration coating from a suspension of thermally activated ZNs on a nonionic porous PVDF (ZNLM-PVDF). The ZNLMs on both supports demonstrated the ability of highly proton-selective ion conduction with low resistances in aqueous electrolyte solutions. The ZNLM-PVDF with PVDF binder was structurally stable, and it achieved a comparably low ASR but much higher proton selectivity compared with a Nafion membrane of same overall thickness. However, detachment between the ZNLM and Nafion layers occurred when the ZNLM-Nafion operated in aqueous electrolyte solutions. Results of this study show the potential for developing ZNLMs as efficient proton-conducting membranes without using expensive ionic polymer matrices. However, the development of polymer-supported ZNLMs is hindered by the current inefficiency in preparing well-dispersed suspensions of open-pore ZNs. Future development of efficient methods for synthesizing open-pore ZNs in dispersed states is key to realizing high-performance ZNLMs on polymers.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Modification of Catalytic Properties of Hollandite Manganese Oxide by Ag Intercalation for Oxidative Acetalization of Ethanol to Diethoxyethane

The effect of addition of Ag to the catalytic properties of hollandite manganese oxide (HMO) was investigated for the oxidative acetalization of ethanol to diethoxyethane. Based on analysis with HRTEM, XRD, and EXAFS, Ag introduced onto HMO by deposition/precipitation was found to be present in different forms in the final catalyst depending on the calcination temperature. It could exist as nanoparticles on the outside surface of HMO nanorods for samples calcined at 60 °C, and as Ag atoms intercalated into the tunnels of the HMO structure for samples calcined at 500 °C. NH 3 desorption results showed that intercalation of Ag resulted in stronger Lewis acidic sites on HMO, which DFT computational results suggested to be due to Ag-induced electron redistribution in the HMO framework. Here, the intercalation of Ag atoms also made the HMO more easily reducible by lowering the H 2 reduction temperature from 500 to 200 °C. Consequently, the sample with intercalated Ag was more active for ethanol oxidation to acetaldehyde, achieving nearly 100% conversion of ethanol and acetaldehyde by 360 °C, and acetalization of acetaldehyde with ethanol to produce diethoxyethane selectively, resulting in 93.5% diethoxyethane yield, which was 10% higher than with samples containing Ag nanoparticles on HMO. This study demonstrated a little-studied phenomenon in which a metal alters the catalytic properties of an oxide electronically but not structurally and without direct participation in the reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1983

Thermal and mechanical properties of advanced, high temperature ceramic-composite insulation

It is found that the mechanical properties of fibrous refractory composite insulation (FRCI) can be improved if a higher calcination temperature is used before final processing. The results also reveal that a higher density FRCI containing 60 wt pct aluminoborosilicate fibers will exhibit minimal surface recession at 1480 C in a convective-heating environment. Another finding is that the material performance in the convective-heating environment is limited by the coating and the temperature capability of its emittance agent. A table is included giving the coating compositions used with the composite insulation and tested in the convectively heated environment at a surface temperature of 1480 C.

Leiser, D. B.↗
DOE OSTI2021

Carbonation, strength development, and characterization of calcined limestone as a potential construction material

The emergence of the modern Portland cement has led to the downfall of lime as a construction material. Consequentially, its use has been limited to repair and restoration of historical buildings. Yet, its lower calcination temperature (~950 °C) and the ability to gain strength through carbonation implies its potential as a sustainable alternative to cement. In this study, calcined limestone was studied concerning its carbonation and strength development. Superplasticizer, raw limestone, and different carbonation regimes were explored as techniques to improve the composite strength development, a shortfall that hinders its re-adoption. The results indicated that the raw limestone as a partial replacement of the calcined limestone significantly improved the carbonation degree and mechanical properties. The average compressive strength reached 20 MPa under 20% CO{sub 2} due to the formation of an interconnected network of calcite as the dominant carbonation product. Supercritical CO{sub 2}, in contrast, formed disjoint particles or agglomerates of carbonates.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mesoporous MoO 2 thin films for high rate Li + storage: Effect of crystallinity and porous structure

MoO 2 has attracted much recent attention as a high capacity energy storage material. While much of the current work on MoO 2 has been focused on the high capacity four-electron reduction, this reaction is limited to slow charging process due to the large volume change and phase transitions involved. In this study we focus on one-electron insertion reactions and demonstrate that ordered mesoporous thin films of MoO 2 can show signatures of pseudocapacitive charge storage. Mesoporous MoO 2 (mp-MoO 2 ) thin films were treated at different temperatures between 350 and 700 °C to explore the role of crystallinity and nanoscale structure on charging dynamics. The porosity and pore size decreased while the crystallinity and grain size increased as the calcination temperature increased. Materials processed at 600 °C showed the best electrochemical performance due to an optimized combination of high crystallinity and small grain size. These materials could be charged and discharged in 24 s while still achieving a Li + storage capacity of 158 mAh/g. While such thin film systems do not constitute a practical energy storage device, the work here provides structural design parameters for the production of future bulk nanoporous materials.

25 ENERGY STORAGE↗
DOE OSTI2022

Review—Electrospun Inorganic Solid-State Electrolyte Fibers for Battery Applications

Inorganic solid-state electrolytes (SSEs), especially Li 7 La 3 Zr 2 O 12 (LLZO), are promising candidates for all solid-state batteries. Generally, SSEs are synthesized by solid-state reactions at high temperatures. The high temperature required to synthesize useful polymorphs (e.g., cubic phase, in the case of LLZO) increases their production cost. To lower the synthesis temperature, several approaches, including doping and crystallite size control via sol-gel processes, have been explored. Recently, electrospinning was used to synthesize the inorganic SSE fibers to control the crystallite size and lower the calcination temperature. Several publications followed that investigated the properties of fibers and demonstrated the use of these fibers in inorganic-polymer composite SSEs. This paper presents a concise discussion of electrospinning, the parameters that control fiber morphology, the synthesis of inorganic SSE fibers, the effect of sintering conditions on the fiber morphology and composition, and the recent use of these fibers in making composite SSEs and other battery applications. Additionally, most of the discussion focuses on LLZO, but this paper also discusses applications of other types of electrospun inorganic electrolyte fibers, the challenges of using these fibers, and possible future directions in this research field.

25 ENERGY STORAGE↗
DOE OSTI2025

Elucidating the phase transformations and grain growth behavior of O3-type sodium-ion layered oxide cathode materials during high temperature synthesis

Understanding the formation mechanism of layered oxide cathodes via solid-state synthesis is imperative to achieving controllability over their materials properties and electrochemical behaviors. In this work, we investigate the phase and microstructure evolution during the synthesis of NaNi 1/3 Fe 1/3 Mn 1/3 O 2 , a model sodium-ion layered oxide cathode, using a combination of imaging, diffraction, and spectroscopic techniques. We unravel the synthetic mechanistic pathways involved in the high-temperature calcination reaction, as well as elaborate the synthesis-microstructure-performance relationship of this material. The formation of the final layered oxide phase involves a gradual transformation through a sodiated oxyhydroxide intermediate. During the reaction, the precursor dehydration reaction dominates at 250–550 °C, while the major sodiation reaction occurs at 550–850 °C. Alongside multiple stages of phase transformations, the final grain structure formation occurs through the continuous growth of the (003) and (104) facets. During the reaction, Mn acts as the charge-compensating element and exhibits depth-dependent characteristics. When the sodiation reaction dominates over dehydration, the reaction intermediates undergo gradual electronic structure changes with increasing temperature, as indicated by the spectral features of TM3d-O2p hybrid states. Calcination duration is also a critical parameter governing the microstructure, surface reactivity, phase fraction distribution and electrochemical performance of the material. The optimal calcination duration was determined to be 18 hours at 850 °C under the conditions evaluated here. Calcination beyond this duration was found to be detrimental to electrochemical performance due to Na and O loss and heterogeneous sodium distribution throughout the particles. Our work sheds light on the complex crystallographic-chemical-microstructural evolution of sodium ion layered oxide cathodes and provides insight into precisely tuning material properties which are intimately linked to battery performances.

25 ENERGY STORAGE↗
DOE OSTI2020

Doping effect of Al in LLZO

Lithium ion batteries have become a common use in most electronic devices and transportation. However, the use of liquid electrolytes poses a serious safe hazard due to their high flammability. The narrow operating temperature and voltage windows also limit further improvement of the energy density.Solid-state lithium batteries with the use of more stable and safer solid electrolyte have garnered much attention and could be the future choice for battery technology. A promising potential candidate for the solid electrolyte component is the garnet type Li 7 La 3 Zr 2 O 12 (LLZO) ceramic material since it possesses high ionic conductivity at room temperature and enables the use of high capacity lithium anode and high voltage/capacity cathodes.However, to form the stable cubic phase of LLZO and high densification,high sintering temperatures above 1100°C is typically required, which causes Lithium loss of the system.Many studieshave been taken to dop LLZO with various precursors such as Ga, Ta, and Al to stabilize the cubic structure and reduce calcination temperature, while the doping effect on sintering densification is still unclear. In this study Al doping along with ball milling were explored to stabilize the cubic phase of LLZO and improve densification, while reducing the amount of impurity phases. Samples were synthesized from the precursors Li 2 CO 3 , Al 2 O 3 , La 2 O 3 , and ZrO 2 by ball milling followed by heat treatment for 12 hours at 1000°C. XRD with Rietveld fitting was used to determine the two phases of LLZO (cubic, tetragonal) and other possible secondary phases. Furthermore,SEM with top and cross sectional views was conducted to investigate the morphology and microstructure of sintered pellets.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Synthesis of Yttrium Oxide Particles for Interfacial Water Radiolysis Studies

Radiolysis of water produces hydrogen gas (H2), posing safety issues for nuclear reactors. Metal oxides can impact H2 formation when water is present on metal oxide surfaces. This presentation focuses on the development of a controllable synthesis of spherical yttrium oxide (Y2O3), that later will be tested for H2 production in water radiolysis. Y2O3 was synthesized via hydrothermal hydrolysis precipitation to form yttrium hydroxide (Y(OH)3), followed by high temperature decomposition to form Y2O3. Various synthesis conditions were tested to determine their impact on particle morphology including reaction time, cooling rate, reactant concentration, and inert atmospheres. Through short reaction times and rapid cooling rate, spherical, relatively uniform particles of 350 nm were obtained. Despite inert atmospheres, carbonate formation occurred in all particles. A calcination temperature of 800°C is necessary to remove impurities. Future work will aim to reduce carbonate formation and improve particle uniformity. The synthetic procedure will be translated to other metal ions to study their impact on interfacial radiolysis.

08 - HYDROGEN↗
DOE OSTI2021

Raman signatures from age-dating PuO 2 since last calcination

The self-irradiation of PuO 2 has been shown to affect the attributes of fifteen vibrational bands in the Raman spectrum. The vibrational bands correspond to the Raman allowed vibrational mode T 2g , overtones, defects, and bands from electronic origin. Defects in the crystal lattice from low-calcination temperature and alpha decay origins are responsible for the changes in the band attributes (band position, full-width half maximum (FWHM), intensity). Crystal lattice defects are also responsible for the growth of the defect bands. The temporal behavior of the vibrational bands can be used to estimate the age of the material since last calcination. Laser annealing was used to reset the material to full crystallinity prior to the aging study. 240 PuO 2 , with an alpha decay rate of 3.67 greater than the decay rate of 239 PuO 2 , was primarily used to assess the alpha decay-induced damage within 3 years. The aging study focused on the time-dependent properties of the T 2g band and the growth of defect bands. The FWHM of the T 2g band and the ratio of the areas of the defect bands/T 2g band were measured through a time period in excess of 3 years. The data from this study were found very close to the data describing the temporal evolution of the lattice constant measured with the X-ray diffraction (XRD) technique. The local physical properties of the material measured with Raman spectroscopy and the lattice parameter constant measured with XRD indicates a strong correlation between the two techniques. Although both techniques provide similar age-dating information, in contrast to the few milligram quantities required for XRD, Raman spectroscopy requires a 10 µm diameter PuO 2 particle to provide an estimate of the material age since last calcination.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

The sol–gel autocombustion as a route towards highly CO 2 -selective, active and long-term stable Cu/ZrO 2 methanol steam reforming catalysts

The adaption of the sol-gel autocombustion method to the Cu/ZrO 2 system opens new pathways for the specific optimisation of the activity, long-term stability and CO 2 selectivity of methanol steam reforming (MSR) catalysts. Calcination of the same post-combustion precursor at 400 °C, 600 °C or 800 °C allows accessing Cu/ZrO 2 interfaces of metallic Cu with either amorphous, tetragonal or monoclinic ZrO 2 , influencing the CO 2 selectivity and the MSR activity distinctly different. While the CO 2 selectivity is less affected, the impact of the post-combustion calcination temperature on the Cu and ZrO 2 catalyst morphology is more pronounced. A porous and largely amorphous ZrO 2 structure in the sample, characteristic for sol-gel autocombustion processes, is obtained at 400 °C. This directly translates into superior activity and long-term stability in MSR compared to Cu/tetragonal ZrO 2 and Cu/monoclinic ZrO 2 obtained by calcination at 600 °C and 800 °C. The morphology of the latter Cu/ZrO 2 catalysts consists of much larger, agglomerated and non-porous crystalline particles. Based on aberration-corrected electron microscopy, we attribute the beneficial catalytic properties of the Cu/amorphous ZrO 2 material partially to the enhanced sintering resistance of copper particles provided by the porous support morphology.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Machinable, high‐conductivity NaSICON through mitigation of humidity effects during solid‐state synthesis

The Na + super ion conductor (NaSICON, Na 1+x Zr 2 Si x P 3-x O 12 ) is a solid electrolyte well-known for fast, selective Na + transport at low temperatures, uniquely enabling sodium-based batteries. Producing high-quality NaSICON from solid-state methods, especially when cost-effective, potentially hygroscopic precursors are used, is not trivial. To understand and eliminate the influence of humidity during processing, a scheme was developed to reproducibly yield a high Na + conductivity (3.75 mS/cm at 25°C, 81.7 mS/cm at 150°C), high density (97%), and machinable NaSICON without the use of binders, sintering aids, or dopants. Controlled humidity studies over 20%–50% RH coupled with thermal, structural, and electrical analysis reveal that calcination temperatures < 1000°C leave NaSICON processing susceptible to water absorption at > 20% RH due to the presence of hygroscopic Na 3 PO 4 and Na 2 CO 3 during shaping, pressing, and sintering. Water absorption results in NaSICON with lower densities, machinability, and Na+ conductivity, due to impaired intergranular Na+ transport. At the other extreme, fully converting precursor to the NaSICON phase at 1230°C before pressing and sintering leads to poor conductivity and density. By calcining at 1000°C, excellent quality NaSICON may be produced under a range of laboratory environments, enabling low-cost production of high-conductivity, machinable NaSICON necessary the ever-growing energy storage market.

NaSICON↗
DOE OSTI2023

Improved Solid-State Reaction Method for Scaled-Up Synthesis of Ceramic Proton-Conducting Electrolyte Materials

Protonic ceramic electrochemical cells (PCECs) represent promising technologies in the production of clean electricity, decarbonized hydrogen, chemicals, and fuels at intermediate temperatures. One of the challenges in commercializing PCECs is to produce the electrolyte materials on a large scale. The conventional solid-state reaction (SSR) method suffers from tedious synthesis procedures and low phase purity of the products due to the formation of unwanted secondary phases. Herein, we report an improved SSR (i-SSR) method for kilogram-scale production of high phase-purity electrolyte material BaZr 0.4 Ce 0.4 Y 0.1 Yb 0.1 O 3–δ (BZCYYb4411). In this method, the ball-milled precursor powders are pelletized prior to calcination, which effectively reduces the length of the diffusion paths between the components during perovskite phase formation. In this study, the synthesis procedure and calcination temperature are carefully optimized for efficient and repeatable production based on the powder crystallization behavior. A combined technoeconomic analysis and life cycle assessment modeling suggest that the i-SSR method could reduce the total production cost and greenhouse gas emissions by up to 19% and 39%, respectively, compared to the conventional SSR method. The high quality of the synthesized electrolyte material is corroborated by the excellent electrical conductivity and electrochemical performance of the fabricated PCEC cells.

36 MATERIALS SCIENCE↗
DOE OSTI2023

An Active and Resilient Bilayer Oxygen Electrode for Intermediate Temperature Reversible Solid Oxide Cells

High temperature solid oxide cells (SOCs) have intrinsic advantage in efficiency over conventional internal combustion engines for power generation and low-temperature electrolysis cells for H2 production. This efficiency advantage could potentially lead to cost saving and emission reduction. However, commercialization of the current SOCs technology is hindered by its poor durability. One major component with the durability issue is oxygen electrode (OE). For example, the durability of OEs can be negatively affected by the gaseous Cr-species originated from the air oxidation of high-temperature alloy interconnect. For electrolysis operation, on the other hand, delamination of OE from electrolyte, particularly at high current densities, has been identified as a major cause for the performance degradation. Therefore, developing robust and active OEs is of critical importance to SOC technology. WE have previously demonstrated a new bilayer OE with strong activity and stability. Here in this presentation, we present recent results of electrochemical characterization on bilayer OE operating under both fuel cell and electrolysis modes. We will first show the optimization of bilayer OE in terms of thickness, morphology, and calcination temperature and their impacts on cell area specific resistance (ASR). With three-electrode symmetric cell configuration, we also show the results of charge transfer ASR of bilayer OE as a function of current density, temperature, and time in different atmospheres. The results are further compared with the baseline OE (LSCF+GDC) to demonstrate the advantage of bilayer OE.

Huang, Kevin↗
DOE OSTI2022

Flash Recycling of Graphite Anodes

The ever-increasing production of commercial lithium-ion batteries (LIBs) will result in a staggering accumulation of waste when they reach their end of life. A closed-loop solution, with effective recycling of spent LIBs, will lessen both the environmental impacts and economic cost of their use. Presently, <5% of spent LIBs are recycled and the regeneration of graphite anodes has, unfortunately, been mostly overlooked despite the considerable cost of battery-grade graphite. Here, in this work, an ultrafast flash recycling method to regenerate the graphite anode is developed and valuable battery metal resources are recovered. Selective Joule heating is applied for only seconds to efficiently decompose the resistive impurities. The generated inorganic salts, including lithium, cobalt, nickel, and manganese, can be easily recollected from the flashed anode waste using diluted acid, specifically 0.1 M HCl. The flash-recycled anode preserves the graphite structure and is coated with a solid-electrolyte-interphase-derived carbon shell, contributing to high initial specific capacity, superior rate performance, and cycling stability, when compared to anode materials recycled using a high-temperature-calcination method. Life-cycle-analysis relative to current graphite production and recycling methods indicate that flash recycling can significantly reduce the total energy consumption and greenhouse gas emission while turning anode recycling into an economically advantageous process.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Surface Modification of Nickel-Rich Cathode Materials by Ionically Conductive Materials at Room Temperature

Nickel-rich cathode materials (LiNi x Mn y Co 1-x-y O 2 , NMC) are promising to push the limits of lithium-ion batteries to higher energy density. This approach is favored in practical applications including electric vehicles and aviation transportation. However, the instability of the NMC at charged state results in safety concerns and poor cycling stability. Surface coating is a practical and effective strategy to address this. Cubic Li7La3Zr2O12 (LLZO) is an ideal coating material regarding the low electron transfer rate and high Li+ conductivity. Thus, a LLZO coating layer can suppress the parasitic reactions in the electrode/electrolyte interface without deteriorating the lithium migration. However, high-temperature calcination seems to inevitably create the chemical couplings between NMC and LLZO, leading to the interdiffusion and degradation of NMC and LLZO crystal structures. This work presents a simple mechanochemical method to effectively coat LLZO on the NMC particle surface. Furthermore, the coated cathode demonstrates superior electrochemical performance compared with the pristine NMC cathode.

25 ENERGY STORAGE↗
DOE OSTI2026

Influence of thermal treatment on structure and catalytic performance of ceria-zirconia supported copper oxide (CuO x /Ce y Zr 1-y O 2 ) catalysts for CO oxidation

Copper oxide (CuO x ) supported on ceria-zirconia (Ce y Zr 1-y O 2 , y = 1.0, 0.5, 0.0) catalysts were investigated to elucidate the effects of thermal treatment on their physicochemical properties and catalytic performance in carbon monoxide (CO) oxidation. Here, the catalysts were synthesized via a one-pot chemical vapor deposition (OP-CVD) method at 700˚C and 900˚C with controlled Cu loading. Characterization techniques, including synchrotron X-ray diffraction (S-XRD), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), inductively coupled plasma spectroscopy (ICP), and N 2 adsorption-desorption, were implemented to probe the crystalline structure, molecular and electronic structure, oxygen vacancies, specific surface area (SSA) and metal loading. CO oxidation was chosen as a model reaction to explore the structure-catalytic performance relationship. A ∼100% CO conversion was achieved at < 150˚C, particularly with the CuO x /CeO 2 catalyst calcined at 700˚C. In contrast, calcination at 900˚C caused a ∼90% decrease in SSA and a ∼24% increase in T 50 . Activity tests revealed that increasing ZrO 2 content lowered CO oxidation activity despite generating more defect sites. In-situ measurement of the 700 °C calcined samples revealed the presence of stable and unstable defects in CuO x /Ce 0.5 Zr 0.5 O 2 and CeO 2 respectively, which play a key role in the activity of the catalysts. The results highlight that catalytic performance is closely related to the SSA. Furthermore, an optimum calcination temperature favor significant oxygen vacancy formation with required CuO x -support interactions, enhancing redox properties and catalytic performance.

36 MATERIALS SCIENCE↗