SEARCH · Search NASA

Results for “capacity enhancement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Multifunctional Separator Allows Stable Cycling of Potassium Metal Anodes and of Potassium Metal Batteries

Here, this is the first report of a multifunctional separator for potassium-metal batteries (KMBs). Here, double-coated tape-cast microscale AlF 3 on polypropylene (AlF 3 @PP) yields state-of-the-art electrochemical performance: symmetric cells are stable after 1000 cycles (2000 h) at 0.5 mA cm –2 and 0.5 mAh cm –2 , with 0.042 V overpotential. Stability is maintained at 5.0 mA cm –2 for 600 cycles (240 h), with 0.138 V overpotential. Postcycled plated surface is dendrite-free, while stripped surface contains smooth solid electrolyte interphase (SEI). Conventional PP cells fail rapidly, with dendrites at plating, and “dead metal” and SEI clumps at stripping. Potassium hexacyanoferrate(III) cathode KMBs with AlF 3 @PP display enhanced capacity retention (91% at 100 cycles vs 58%). AlF 3 partially reacts with K to form an artificial SEI containing KF, AlF 3 , and Al 2 O 3 phases. The AlF 3 @PP promotes complete electrolyte wetting and enhances uptake, improves ion conductivity, and increases ion transference number. The higher of K + transference number is ascribed to the strong interaction between AlF 3 and FSI – anions, as revealed through 19 F NMR. The enhancement in wetting and performance is general, being demonstrated with ester- and ether-based solvents, with K-, Na-, or Li- salts, and with different commercial separators. In full batteries, AlF 3 prevents Fe crossover and cycling-induced cathode pulverization.

NMB↗

DOE OSTI2024

Effects of Calcination Conditions on the Structural and Electrochemical Behaviors of High‐Nickel, Cobalt‐Free LiNi 0.9 Mn 0.1 O 2 Cathode

Abstract Eliminating cobalt from high‐nickel layered oxide cathodes lowers the cost of lithium‐ion batteries for electric vehicles. However, cobalt‐free cathodes with high Mn 4+ and Ni 2+ contents are prone to Li/Ni mixing after synthesis, potentially compromising battery energy density, rate capability, and cycling stability. Without cobalt facilitating cation ordering in the layered structure, the degree of Li/Ni mixing in cobalt‐free cathodes depends heavily on the calcination conditions. In this study, a systematic exploration of calcination temperatures and LiOH ratio for LiNi 0.9 Mn 0.1 O 2 (NM‐90) provides detailed insights into the optimal synthesis conditions for high‐capacity cobalt‐free cathodes with extended cycle life. Surprisingly, high Li/Ni mixing does not necessarily lead to poor cycling stability whereas low Li/Ni mixing does not guarantee a long cycle life. More importantly, although excessive calcination temperature can further decrease Li/Ni mixing, it does not necessarily enhance capacity. Instead, the pernicious effects from the H2 → H3 phase transition are amplified due to a pronounced two‐phase reaction. An extensive suite of chemical and structural characterization methods uncovers a correlation between elevated calcination temperature, phase transformation, cation ordering, and capacity fading behavior: “overcooking” high‐nickel, cobalt‐free cathodes induce structural arrangement toward that of LiNiO 2 , with exacerbated lattice distortion and surface instability accelerating capacity fade.

Lee, Steven↗

DOE OSTI2025

Two-Dimensional Siloxene Nanosheets: Understanding the Effect of Heat Treatment on the Surface Chemistry and Resulting Electrochemistry in Lithium-Based Batteries

Two-dimensional (2D) silicon materials are conceptually appealing as negative electrode materials in lithium-ion batteries due to their layered morphology, which can accommodate (de)lithiation-induced volume changes. Herein, heat treatment of 2D Siloxene materials was used to modify the surface functional groups to determine the impact on the electrochemical behavior. Spectroscopic characterization of the heat-treated nanosheets confirmed the loss of oxygenated and hydride surface functional groups with an increased annealing temperature. Formation and disproportionation of the amorphous suboxides with increasing heat treatment were affirmed with lab and synchrotron-based measurements. A reduced irreversible capacity was observed for Siloxene with a higher temperature heat treatment consistent with the formation of a more favorable surface electrolyte interphase (SEI). A Siloxene-400||NMC622 full cell (prepared with 400 °C-annealed Siloxene (Siloxene-400) and LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622)) showed significantly enhanced capacity and rate capability compared to a nano Si||NMC622 cell. Finally, these results illustrate the ability of thermal annealing to modify the surface functional groups of Siloxene and highlight the favorable impact of the appropriate surface functionality on the electrochemistry of Siloxene in lithium cells.

25 ENERGY STORAGE↗

DOE OSTI2023

Toward Stable Cycling of a Cost-Effective Cation-Disordered Rocksalt Cathode via Fluorination

The recently developed Li-excess cation-disordered rock salts (DRXs) exhibit an excellent chemical diversity for the development of alternative Co/Ni-free high-energy cathodes. Herein, the synthesis of a highly fluorinated DRX cathode, Li 1.2 Mn 0.6 Ti 0.2 O 1.8 F 0.2 , based on cost-effective and earth-abundant transition metals, via a solid-state reaction, is reported. The fluorinated DRX cathode using ammonium fluoride precursor exhibits more uniform particle size and delivers a specific discharge capacity of 233 mAh g -1 and specific energy of 754 Wh kg -1 , with 206 mAh g -1 retained after 200 cycles. Further, the combined synchrotron X-ray absorption spectroscopy and resonant inelastic X-ray scattering spectroscopy analysis reveals that the remarkable cycling performance is attributed to the high fluorination and thus enhanced Mn content, enabling the utilization of more Mn redox than the oxide analog. This study demonstrates a great promise to develop next-generation cost-effective DRX cathodes with enhanced capacity retention for high-energy Li-ion batteries.

25 ENERGY STORAGE↗

DOE OSTI2022

Preparation of: I. intercalative metal oxide/conductive polymer composites as electrode materials for rechargeable batteries; II. sodium rich manganese oxide hydrate with capacity for aqueous Na-ion electrochemical energy storage

The present invention is directed at intercalative metal oxide/conductive polymer composites suitable for use as electrode materials for rechargeable batteries. The composites can be prepared by agitation of the metal oxide and the conductive polymer in aqueous media. The present invention is also directed at a sodium rich layered manganese oxide hydrate prepared by annealing manganese (II, III) oxide and sodium hydroxide. The sodium rich manganese (III, IV) oxide so formed indicates an enhanced capacity for Na-ion storage suitable for the use of electrode materials for aqueous energy storage.

Xiaowei, Teng↗

DOE OSTI2026

Fe-single atom catalysts facilitate fast electron transfer with MoS 2 /SnS 2 cathodes in lithium–sulfur batteries

Lithium–sulfur batteries (LSBs) emerge as promising next-generation energy storage systems offering cost-effectiveness, environmental friendliness, and high theoretical energy density. The practical implementation of LSBs faces significant hindrances due to the shuttle effect and sluggish redox reactions. To address these challenges, single-atom catalyst (SAC) based combination materials from d-block elements can offer increased active catalytic sites, rapid charge transfer, accelerated electron migration, and fast sulfur redox conversion kinetics of lithium polysulfides (LiPSs). In this study, we fabricated three different LSB cathodes: pure S, S@MoS 2 /SnS 2 , and S@Fe–MoS 2 /SnS 2 . These cathodes were then used to explore the cycle life, capacity, rate capability, and redox kinetic reactions of LiPSs while assessing the influence of Fe-SACs on their performance. As a result, LSBs with S@Fe–MoS 2 /SnS 2 cathodes demonstrate an extended cycle life of 1000 cycles at a C-rate of 0.2C, maintaining a capacity close to 500 mA h g −1 , the highest initial discharge capacity of 1622 mA h g −1 and 1066 mA h g −1 at 0.05C and 0.2C, and excellent rate capabilities of 708 mA h g −1 and 558 mA h g −1 at 1C and 2C, respectively. The synergistic effect of the Fe-SAC-based combination cathode (S@Fe–MoS 2 /SnS 2 ) creates plentiful adsorptive and highly active catalytic sites, resulting in substantially enhanced capacity for adsorbing soluble long-chain LiPSs. This facilitates ultra-fast redox kinetics, surpassing the performance of the S@MoS 2 /SnS 2 and pure S cathodes. In the ex situ analysis, results from powder X-ray diffraction (XRD) to observe the new phase, soft X-ray absorption spectroscopy (XAS) to investigate the electronic structure, and hard X-ray photoelectron microscopy (HAXPES) with different energies (900 eV, 2000 eV, and 6000 eV) to track the chemical-state evolution of Fe-SACs in MoS 2 /SnS 2 cathodes displayed notable electrochemical reversibility involving S 8 ⇄ LiPSs ⇄ Li 2 S conversion even after 1000 cycles. Additionally, in situ, operando Raman analysis can unveil a novel catalytic mechanism of Fe-SACs in MoS 2 /SnS 2 “facilitating rapid electron transfer” during the discharge and charge processes of LSBs involving the conversion of S 8 ⇄ long-chain LiPSs ⇄ Li 2 S 2 /Li 2 S. This study elucidates the working mechanism of Fe-SAC cathodes, offering insights into overcoming the shuttle effect and facilitating sulfur redox kinetics to advance commercial LSBs.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Understanding particle size effect on fast-charging behavior of graphite anode using ultra-thin-layer electrodes

Extreme fast charging (≤ 15 min) of lithium-ion batteries is highly desirable to accelerate mass-market adoption of electric vehicles. However, significant capacity fading, as well as safety issues due to the lithium plating caused by the fast charging rate, limit its implementation. In this study, we investigated the fast-charging capability of graphite materials with various particle sizes. To eliminate the Li + ion concentration gradient effect across the thickness of the electrode, ultra-thin-layer graphite electrodes were developed to investigate the "real" fast-charging capability of graphite at the particle level. Electrochemical assessments as well as microscopic characterizations revealed that smaller particles exhibited superior fast-charging performance, featuring enhanced capacity reversibility, faster charging rate, and less lithium plating under the same fast-charging conditions. It is shown that small-particle graphite (mean radius of 3.3 μm) could withstand a 4C charge (to 80 % state-of-charge) without plating, with minimal plating occurring at 6C. Thicker particles exhibited plating at lower C-rates. Since the experimental data could not directly explain whether intra-particle diffusion limitations or interfacial reaction limitations dominated the plating mechanism, the pseudo-2-dimensional model was used to evaluate the most likely plating mechanism. The model suggested that particle-level diffusion is the dominant mechanism contributing to plating at high rates. Finally, this work provides comprehensive insights into the particle size effects on fast-charging capability, offering a better understanding of fast-charging behavior and valuable guidance for designing optimal electrode architecture for high-rate lithium-ion batteries.

25 ENERGY STORAGE↗

DOE OSTI2024

Ultradynamic Isoreticularly Expanded Porous Organic Crystals

Porous organic materials showcasing large framework dynamics present new paths for adsorption and separation with enhanced capacity and selectivity beyond the size-sieving limits, which is attributed to their guest-responsive sorption behaviors. Porous hydrogen-bonded crosslinked organic frameworks (H C OFs) are attractive for their remarkable ability to undergo guest-triggered expansion and contraction facilitated by their flexible covalent crosslinkages. However, the voids of H C OFs remain limited, which restrains the extent of the framework dynamics. Here in this work, we synthesized a series of H C OFs characterized by unprecedented size expansion capabilities induced by solvents. These H C OFs were constructed by isoreticularly co-crystallizing two complementary sets of hydrogen bonding building blocks to generate porous molecular crystals, which were crosslinked through thiol–ene/yne single-crystal-to-single-crystal transformations. The generated H C OFs exhibit enhanced chemical durability, high crystallinity, and extraordinary framework dynamics. For instance, H C OF-104 crystals featuring a pore diameter of 13.6 Å expanded in DMF to 300 ± 10% of their original lengths within just 1 min. This expansion allows the HCOFs to adsorb guest molecules that are significantly larger than the pore sizes of their crystalline states. Through methanol-induced contraction, these large guests were encapsulated in the fast-contracted H C OFs. These advancements in porous framework dynamics pave the way for new methods of encapsulating guests for targeted delivery.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Highly efficient interface stabilization for ambient-temperature quasi-solid-state sodium metal batteries

Solid-state sodium (Na) batteries (SSSBs) using sulfide-based solid electrolytes (SSEs) hold tremendous promise due to their high theoretical specific capacity, enhanced safety and abundant resources. However, detrimental interfacial issues between SSEs and Na metal present a major challenge to the advancement of sulfide-based SSSBs. To address interfacial issues, we demonstrate an efficient approach by incorporating an ionic liquid electrolyte ((PYR/Na)TFSI) as interlayer to stabilize the Na metal/SSE interface. The presence of the (PYR/Na)TFSI interlayer enables the formation of a stable solid electrolyte interphase (SEI) to prevent the harmful reactions and inhibit Na dendrites. Combination of ab initio molecular dynamics simulations and X-ray photoelectron spectroscopy revealed that this stable SEI is largely composed of reduced products of TFSI -, such as NaF and CF 3 . As a result, the symmetric cells exhibited stable Na plating/striping cycling for 300 h at 0.1 mA cm -2 . In addition, FeS2||Na quasi-solid-state batteries delivered an impressive specific capacity of over 300 mAh g -1 under the current density of 20 mA g -1 at room temperature. Under a higher current density (100 mA g -1 ), such batteries performed with long-term cycling stability and maintained a specific capacity of around 103 mAh g -1 after 330 cycles. This work demonstrates the novel perspective of using an ionic liquid interlayer to address interfacial issues, contributing to the advancement of high-performance SSSBs for the next-generation energy storage systems.

25 ENERGY STORAGE↗

DOE OSTI2024

Entropy-Stabilized Multication Fluorides as a Conversion-Type Cathode for Li-Ion Batteries–Impact of Element Selection

Metal fluorides (e.g., FeF 2 and FeF 3 ) have received attention as conversion-type cathode materials for Li-ion batteries due to their higher theoretical capacity compared to that of common intercalation materials. However, their practical use has been hindered by low round-trip efficiency, voltage hysteresis, and capacity fading. Cation substitution has been proposed to address these challenges, and recent advancements in battery performance involve the introduction of entropy stabilization in an attempt to facilitate reversible conversion reactions by increasing configurational entropy. Building on this concept, high entropy fluorides with five cations were synthesized by using a simple mechanochemical route. In order to examine the impact of element selection, Co 0.2 Cu 0.2 Ni 0.2 Zn 0.2 Fe 0.2 F 2 (HEF-Fe) was compared with Co 0.2 Cu 0.2 Ni 0.2 Zn 0.2 Mg 0.2 F 2 (HEF-Mg), replacing electrochemically inactive Mg with Fe as an active participant in the conversion reaction. Combining electrochemical measurements with first-principles calculations, high-resolution electron microscopy, and synchrotron X-ray analysis, HEFs’ battery performances and conversion reaction mechanisms were investigated in detail. The results highlighted that replacement of Mg with Fe was beneficial, with enhanced capacity, rate capability, and surface stability. In addition, it was found that HEF-Fe showed similar cycle stability without an electrochemically inactive element. In conclusion, these findings provide valuable insights for the design of high entropy multielement fluorides for improved Li-ion battery performance.

25 ENERGY STORAGE↗

DOE OSTI2022

Thermodynamically Driven Synthetic Optimization for Cation-Disordered Rock Salt Cathodes

Relating the synthesis conditions of materials to their functional performance has long been an experience-based trial-and-error process. However, this methodology is not always efficient in identifying an appropriate protocol and can lead to overlooked opportunities for the performance optimization of materials through simple modifications of the synthesis process. In this work, we systematically track the structural evolution in the synthesis of a representative disordered rocksalt (a promising next-generation Li-ion cathode material) at the scale of both the long-range crystal structure and the short-range atomic structure using various in situ and ex situ techniques, including transmission electron microscopy, X-ray diffraction, and pair distribution function analysis. Further, an optimization strategy is proposed for the synthesis protocol, leading to a remarkably enhanced capacity (specific energy) of 313 mAh g –1 (987 Wh kg –1 ) at a low rate (20 mA g –1 ), with a capacity of more than 140 mAh g –1 retained even at a very high cycling rate of 2,000 mA g –1 . This strategy is further rationalized using ab initio calculations, and important opportunities for synthetic optimization demonstrated in this study are highlighted.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Photosynthetic adaptation to polar life: Energy balance, photoprotection and genetic redundancy

The persistent low temperature that characterize polar habitats combined with the requirement for light for all photoautotrophs creates a conundrum. The absorption of too much light at low temperature can cause an energy imbalance that decreases photosynthetic performance that has a negative impact on growth and can affect long-term survival. The goal of this review is to survey the mechanism(s) by which polar photoautotrophs maintain cellular energy balance, that is, photostasis to overcome the potential for cellular energy imbalance in their low temperature environments. Photopsychrophiles are photosynthetic organisms that are obligately adapted to low temperature (0⁰- 15 °C) but usually die at higher temperatures (≥20 °C). In contrast, photopsychrotolerant species can usually tolerate and survive a broad range of temperatures (5⁰- 40 °C). First, we summarize the basic concepts of excess excitation energy, energy balance, photoprotection and photostasis and their importance to survival in polar habitats. Second, we compare the photoprotective mechanisms that underlie photostasis and survival in aquatic cyanobacteria and green algae as well as terrestrial Antarctic and Arctic plants. We show that polar photopsychrophilic and photopsychrotolerant organisms attain energy balance at low temperature either through a regulated reduction in the efficiency of light absorption or through enhanced capacity to consume photosynthetic electrons by the induction of O 2 as an alternative electron acceptor. Finally, we compare the published genomes of three photopsychrophilic and one photopsychrotolerant alga with five mesophilic green algae including the model green alga, Chlamydomonas reinhardtii. We relate our genomic analyses to photoprotective mechanisms that contribute to the potential attainment of photostasis. Finally, we discuss how the observed genomic redundancy in photopsychrophilic genomes may confer energy balance, photoprotection and resilience to their harsh polar environment. Primary production in aquatic, Antarctic and Arctic environments is dependent on diverse algal and cyanobacterial communities. Although mosses and lichens dominate the Antarctic terrestrial landscape, only two extant angiosperms exist in the Antarctic. Furthermore, the identification of a single ‘molecular key’ to unravel adaptation of photopsychrophily and photopsychrotolerance remains elusive. Since these photoautotrophs represent excellent biomarkers to assess the impact of global warming on polar ecosystems, increased study of these polar photoautotrophs remains essential.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2022

Carbon Dioxide Capture Chemistry of Amino Acid Functionalized Metal-Organic Frameworks in Humid Flue Gas

Here, metal-organic framework-808 has been functionalized with 11 amino acids (AA) to produce a series of MOF-808-AA structures. The adsorption of CO 2 under flue gas conditions revealed that glycine- and DL-lysine-functionalized MOF-808 (MOF-808-Gly and -DL-Lys) have the highest uptake capacities. Enhanced CO 2 capture performance in the presence of water was observed and studied using single-component sorption isotherms, CO 2 /H 2 O binary isotherm, and dynamic breakthrough measurements. The key to the favorable performance was uncovered by deciphering the mechanism of CO 2 capture in the pores and attributed to the formation of bicarbonate as evidenced by 13 C and 15 N solid-state nuclear magnetic resonance spectroscopy studies. Based on these results, we examined the performance of MOF-808-Gly in simulated coal flue gas conditions and found that it is possible to capture and release CO 2 by vacuum swing adsorption. MOF-808-Gly was cycled at least 80 times with full retention of performance. This study significantly advances our understanding of CO 2 chemistry in MOFs by revealing how strongly bound amine moieties to the MOF backbone create the chemistry and environment within the pores, leading to the binding and release of CO 2 under mild conditions without application of heat.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2024

Discerning molecular-level CO 2 adsorption behavior in amine-modified sorbents within a controlled CO 2 /H 2 O environment towards direct air capture

Sorbents designed for direct air capture (DAC) play a crucial role in the pursuit of achieving net-zero carbon dioxide emissions. This study elucidates CO 2 adsorption from dilute, humidified CO 2 streams onto an amine-modified benchmark DAC adsorbent via solid-state NMR spectroscopy. Various NMR techniques, including 1D 1 H MAS, 13 C MAS, 2D 1 H– 13 C HETCOR NMR, and 1 H R 2 and R 1ρ relaxometry reveal the impact of CO 2 partial pressure and H 2 O on CO 2 adsorption behavior. Here we find that CO 2 concentration governs the stepwise formation of ammonium carbamate, carbamic acid, and physisorbed CO 2 , where relative humidity (RH) at a desired low (<400 ppm) CO 2 loading affects total CO 2 uptake. The relaxation studies reveal the cooperative or competitive nature of H 2 O–CO 2 sorption in CO 2 -dilute humid gas, and in particular polymer swelling upon humidification. From those results, we demonstrate that the observed absorption capacity enhancement by humidity is caused by pore opening due to sorbent swelling, and not by bicarbonate formation. This NMR-discerned speciation provides insights into sorption behavior at different RHs in dilute CO 2 gas streams, simulating real-world atmospheric conditions, and governs the design of efficient and adaptable material-process combinations for solid sorbent DAC.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Electrospinning of ultra-high molecular weight polymers into aligned nanofibers and their application in chemical separations

Ultra-high molecular weight (UHMW, >10 6 g mol −1 ) vinyl polymers are increasingly accessible through photoiniferter polymerization, yet their behavior in electrospinning has received comparatively little attention. Here, we explore the electrospinning of UHMW poly(methyl acrylate), poly(methyl methacrylate), poly(N,N-dimethylacrylamide), and poly(styrene-co-pentafluorostyrene) synthesized by photoiniferter polymerization, with number-average molecular weights (M n ) greater than 1000 kDa and dispersities below 1.4. UHMW polymers form stable Taylor cones and discrete fibers at solution concentrations as low as 0.5 wt% due to their large number of entanglements, a threshold unachievable with low molecular weight (M n = 20–54 kDa) polymers of the same chemistry. Using poly(methyl methacrylate) and poly(styrene-co-pentafluorostyrene) as model systems, we demonstrate that fiber diameter can be tuned from 350 nm to 20 μm through systematic variation of polymer concentration (0.01 to 4 wt%) and flow rate (0.5 to 10 mL h −1 ). Additionally, we find that collector rotation rate governs fiber alignment, with highly aligned mats obtained with drum rotation speeds of 1000 RPM. Reversing the polarity of the electric field during electrospinning reorients the surface chemistry of these fiber mats without altering their microscale morphology, shifting the water contact angle by 7° (89° to 96°) and providing a two-fold binding capacity enhancement in cationic dye uptake. These results show that the high entanglement densities of UHMW vinyl polymers shift the accessible electrospinning window to dilute solutions and that electric-field polarity is a useful lever to control the surface chemistry in the resulting fibers.

Marquez, Joshua D. [University of Florida, Gainesv↗

DOE OSTI2020

Direct kinetic measurements and theoretical predictions of an isoprene-derived Criegee intermediate

Isoprene has the highest emission into Earth’s atmosphere of any nonmethane hydrocarbon. Atmospheric processing of alkenes, including isoprene, via ozonolysis leads to the formation of zwitterionic reactive intermediates, known as Criegee intermediates (CIs). Direct studies have revealed that reactions involving simple CIs can significantly impact the tropospheric oxidizing capacity, enhance particulate formation, and degrade local air quality. Methyl vinyl ketone oxide (MVK-oxide) is a four-carbon, asymmetric, resonance-stabilized CI, produced with 21 to 23% yield from isoprene ozonolysis, yet its reactivity has not been directly studied. We present direct kinetic measurements of MVK-oxide reactions with key atmospheric species using absorption spectroscopy. Direct UV-Vis absorption spectra from two independent flow cell experiments overlap with the molecular beam UV-Vis-depletion spectra reported recently [M. F. Vansco, B. Marchetti, M. I. Lester, J. Chem. Phys. 149, 44309 (2018)] but suggest different conformer distributions under jet-cooled and thermal conditions. Comparison of the experimental lifetime herein with theory indicates only the syn -conformers are observed; anti -conformers are calculated to be removed much more rapidly via unimolecular decay. We observe experimentally and predict theoretically fast reaction of syn -MVK-oxide with SO 2 and formic acid, similar to smaller alkyl-substituted CIs, and by contrast, slow removal in the presence of water. We determine products through complementary multiplexed photoionization mass spectrometry, observing SO 3 and identifying organic hydroperoxide formation from reaction with SO 2 and formic acid, respectively. The tropospheric implications of these reactions are evaluated using a global chemistry and transport model.

09 BIOMASS FUELS↗

DOE OSTI2020

Seismic refraction tracks porosity generation and possible CO 2 production at depth under a headwater catchment

Significance To understand groundwater in weathered bedrock aquifers, we explore (bio)geochemical reactions using geophysical measurements. The result leads to a conceptual model for the three-dimensional distribution of geochemical alteration in the subsurface—well beyond the typical approach of inferring (bio)geochemical reactions in the subsurface from pits, boreholes, and outcrops. With this geophysical technique we discovered the prevalence of gas beneath the water table at this site. This geophysical viewing of the subsurface highlights patterns of water movement, reactions of clays, and microbial and abiotic gas-producing reactions recorded in the subsurface and thus illuminates storage, flow, and reactions of groundwater in bedrock systems. Protecting the groundwater resource beneath our feet will rely on such enhanced capacities to see into the subsurface.

58 GEOSCIENCES↗

DOE OSTI2024

Discovery and adaptation of microbes that degrade oxidized low-density polyethylene films

There is a growing interest in developing a methodology for effectively cleaving carbon–carbon (C–C) bonds in polymer backbones through bioconversion processes that utilize microorganisms and their enzymes. This upsurge of interest is driven by the goal of achieving a circular economy. Polyolefin post-consumer plastics are a substantial source of carbon, but the recycling potential is severely limited. Upcycling routes are needed for converting polyolefin post-consumer plastics into value-added products while concurrently mitigating adverse environmental effects. These materials contain carbon-based chemicals that can, in principle, serve as the feedstock for microbial metabolism. Some microbes have been reported to grow on polyolefin plastics, but the rate of biodegradation is insufficient for industrial processes. In this study, low-density polyethylene (LDPE) films were subjected to two mild ozone-based oxidation treatments, which facilitated biodegradation. The degree of oxidation was determined by Fourier transform infrared spectroscopy via analysis of the carbonyl index (1,710/1,460 cm −1 ), which ranged from 0.3 to 2.0, and also via analysis of the carboxylic acid content. Following oxidation of the films, studies were conducted to investigate the ability of a panel of polyvinyl alcohol-degrading microbes to degrade the oxidized films. A defined minimal medium was used to cultivate and assess microbial growth on the oxidized films. Following 45 days of cultivation, the most effective strains were further cultivated up to three additional generations on the oxidized film substrates to improve their ability to degrade the oxidized LDPE films. After these enrichments, we identified a strain from the third generation of Pseudomonas sp. Rh926 that exhibited significant cell growth and reduced the oxidized LDPE film mass by 25% in 30 days, demonstrating an enhanced capacity for degrading the oxidized LDPE films.

Adaptation↗