Search NASA⌕ Search

SEARCH · Search NASA

Results for “carbon phenolic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Flight test of carbon-phenolic on a spacecraft launched by the pacemaker vehicle system

Carbon-phenolic material consisting of 50 percent carbon fibers and 50 percent phenolic resin was flight tested on a recoverable spacecraft launched by the Pacemaker vehicle system. The heat shield of the spacecraft was fabricated so that the carbon fibers in the ablator material had different orientations over several areas of the spacecraft. The environment in which the spacecraft was tested produced heating rates on the hemispherical nose up to 13.6 MW/sq m (1200 Btu/sq ft/sec) and stagnation-point pressures up to 1.27 MN/sq m (12.5 atm). The experimental results are presented. Due to high heating rates and possible spallation and mechanical char removal the greatest mass loss occurred in the nose region. Essentially uniform surface recession and char thickness were observed on the conical section of the spacecraft. A comparison of measured heating rates with computed turbulent and laminar heating rates, as well as measurements of sound-pressure fluctuations in the boundary layer obtained with acoustic sensors, indicated that the boundary layer underwent transition. The acoustic sensor provides an interesting new data form for the general study of boundary-layer transition for free-flight investigations.

Walton, T. E., Jr.↗
NASA NTRS1992

Anomalous swelling behavior of FM 5055 carbon phenolic composite

The swelling response of a typical carbon phenolic composite was measured in the three primary material directions. The data obtained sugrest that at low and high relative humidities the incremental increase in moisture absorption can be attributed primarily to the resin. At intermediate relative humidities, the water is moving largely into the carbonized fibers.

Stokes, E. H.↗
NASA NTRSDate not supplied

3D Woven Mid-Density Carbon Phenolic (3MDCP) Thermal Protection System Development

3-Dimensionally Woven, Mid-Density, Carbon Phenolic (3MDCP) Thermal Protection System (TPS) material is derived from the dual layer 3D woven Heatshield for Extreme Entry Environment Technology (HEEET) material. The baseline 3MDCP design is a single piece thermal protection system that avoids the manufacturing and certification challenges associated with a tiled configuration. 3MDCP is targeted for very aggressive entry environments such as high-speed sample return missions to Earth and missions to Saturn, Venus and the ice giants. A 3MDCP heatshield begins as a flat woven preform that is formed to a given heatshield shape and then infused with phenolic resin. NASA Ames, in collaboration with TEAM Inc. (weaving) and Fiber Materials Inc. (both Spirit AeroSystems Companies) have been developing and demonstrating the manufacturing processes to fabricate a 3MDCP heatshield at a diameter of 1.25 meters. The process of forming the flat woven preform into the final heatshield shape, a sphere-cone geometry, involves local movement of the yarns in the weave. This results in a single piece heatshield with continuous fibers, albeit with property variations between different regions on the heatshield. This presentation will provide a high-level status of 3MDCP development. This will include an overview of the manufacturing processes, with an emphasis on the impact of forming on fiber orientation, material properties and performance. The presentation will layout the plan for testing to assess the impact of forming on properties and review preliminary data comparing properties of flat to formed materials.

Thermal Protection System↗
NASA NTRS1982

Transport properties associated with carbon-phenolic ablators

Entry vehicle heat shields designed for entry into the atmosphere of the outer planets are usually made of carbonaceous material such as carbon-phenolic ablator. Ablative injection of this material is an important mechanism for reducing the heat at the surface of the entry vehicle. Conductive transport properties in the shock layer are important for some entry conditions. The kinetic theory of gases has been used to calculate the transport properties for 17 gaseous species obtained from the ablation of carbon-phenolic heat shields. Results are presented for the pure species and for the gas mixture.

Biolsi, L.↗
NASA NTRS1981

Experimental determination of ablation vapor species from carbon phenolic heat-shield materials

The relative concentrations of vapors produced from carbon phenolic composites under thermal loadings approximating those expected at peak heating during vehicle entry into the atmospheres of the outer planets have been determined. The technique of vaporizing the surface of bulk samples by laser irradiation while measuring in situ the vapor species by mass spectrometry is described. Results show that vapor composition varies with irradiance level and with depth of heating (or extent of pyrolysis). Attempts are made to compare these experimental results with the theoretical predictions from computer codes.

Lincoln, K. A.↗
NASA NTRS1991

Proceedings of the Advisory Committee on Standardization of Carbon-Phenolic Test Methods and Specifications

Proceedings of the Advisory Committee on Standardization of carbon-phenolic test methods and specifications are compiled. The following subject areas are covered: ashing procedures and alkali metal content of carbon fiber and fabrics; SPIP product identification code; SPIP initiative to adopt a water-soluble rayon yarn lubricant/size for weaving; fabric oxidation mass loss test; shelf life limit for prepregs, industry standard; silicon contamination update; resin, filler, and fabric content in prepreg; carbon assay testing calibration; thiokol rayon specifications; and SPIP low conductivity PAN program.

Hall, William B.↗
NASA NTRS1989

Process modeling for carbon-phenolic nozzle materials

A thermochemical model based on the SINDA heat transfer program is developed for carbon-phenolic nozzle material processes. The model can be used to optimize cure cycles and to predict material properties based on the types of materials and the process by which these materials are used to make nozzle components. Chemical kinetic constants for Fiberite MX4926 were determined so that optimization of cure cycles for the current Space Shuttle Solid Rocket Motor nozzle rings can be determined.

Letson, Mischell A.↗
NASA NTRS2001

Thermal/Pyrolysis Gas Flow Analysis of Carbon Phenolic Material

Provided in this study are predicted in-depth temperature and pyrolysis gas pressure distributions for carbon phenolic materials that are externally heated with a laser source. Governing equations, numerical techniques and comparisons to measured temperature data are also presented. Surface thermochemical conditions were determined using the Aerotherm Chemical Equilibrium (ACE) program. Surface heating simulation used facility calibrated radiative and convective flux levels. Temperatures and pyrolysis gas pressures are predicted using an upgraded form of the SINDA/CMA program that was developed by NASA during the Solid Propulsion Integrity Program (SPIP). Multispecie mass balance, tracking of condensable vapors, high heat rate kinetics, real gas compressibility and reduced mixture viscosity's have been added to the algorithm. In general, surface and in-depth temperature comparisons are very good. Specie partial pressures calculations show that a saturated water-vapor mixture is the main contributor to peak in-depth total pressure. Further, for most of the cases studied, the water-vapor mixture is driven near the critical point and is believed to significantly increase the local heat capacity of the composite material. This phenomenon if not accounted for in analysis models may lead to an over prediction in temperature response in charring regions of the material.

Clayton, J. Louie↗
NASA NTRS1992

A finite element method for the thermochemical decomposition of polymeric materials. II - Carbon phenolic composites

A previously developed formulation for modeling the thermomechanical behavior of chemically decomposing, polymeric materials is verified by simulating the response of carbon phenolic specimens during two high temperature tests: restrained thermal growth and free thermal expansion. Plane strain and plane stress models are used to simulate the specimen response, respectively. In addition, the influence of the poroelasticity constants upon the specimen response is examined through a series of parametric studies.

Sullivan, R. M.↗
NASA NTRS1986

Standardization of carbon-phenolic composite test methodology

The objective of this study was to evaluate the residual volatiles, filler content, and resin flow test procedures for carbon-phenolic prepreg materials. The residual volatile test procedure was rewritten with tighter procedure control which was then evaluated by round robin testing by four laboratories on the same rolls of prepreg. Results indicated that the residual volatiles test was too operator and equipment dependent to be reliable, and it was recommended that the test be discontinued. The resin flow test procedures were rewritten with tighter procedure control, and it is now considered to be an acceptable test. It was recommended that the filler content determination be made prior to prepregging.

Hall, W. B.↗
NASA NTRS1991

Equilibrated moisture content of several carbon phenolics and their relationship to resin, fiber, and interface properties

This study focuses on the relationship between relative humidity and the equilibrated moisture content of several variants of two distinctly different carbon phenolic composites. One of the materials gives a typical exponential relationship between RH and equilibrated moisture content while the second gives an inverse sigmoidal relationship with the largest increase in moisture between 45-60 percent relative humidity. The possible relationship between the shape of the curves and the nature of the material constituents is discussed.

Stokes, E. H.↗
NASA NTRSDate not supplied

3D Woven Mid-Density Carbon Phenolic (3MDCP) Full-Scale Heatshield Development for Mars Sample Return (MSR) Earth Entry System (EES)

The Mars Sample Return (MSR) mission will be returning samples of Martian soil to Earth. The samples will be returned in the Earth Entry System (EES). The EES capsule is protected by a new thermal protection system; the 3-Dimensionally Woven, Mid-Density, Carbon Phenolic (3MDCP) material which is derived from the Heatshield for Extreme Entry Environment Technology (HEEET). The baseline 3MDCP design is a single piece thermal protection system that avoids the manufacturing and certification challenges associated with a tiled configuration. A 3MDCP heatshield begins as a flat woven preform that is formed to the final heatshield shape and then infused with phenolic resin. A NASA Ames lead team, in collaboration with Spirit Textiles (formerly TEAM Inc.), Fiber Materials Inc. (FMI, a Spirit AeroSystems Company), and Kratos SRE, has been developing and demonstrating the processes to fabricate the 3MDCP heatshield and characterize the resulting properties. The process of forming the flat woven preform into the final heatshield shape, a sphere-cone geometry with a 52.5° cone angle, involves local but substantial movement of the yarns in the weave. This results in continuous fibers across the single piece heatshield, albeit with property variations between different regions of the heatshield. This presentation will provide a high-level status of 3MDCP development for the MSR EES heatshield. This will include an overview of the manufacturing processes with an emphasis on the impact of forming on fiber orientation, material properties, and performance. Results comparing preliminary formed and flat materials will be shown. Additionally, the presentation will layout the broader plan for property testing and tie-in to aerothermal performance.

Peter Edward Marshall↗
NASA NTRSDate not supplied

Arc Jet Testing of 3D Mid-Density Carbon Phenolic (3MDCP) for Mars Sample Return

When accounting for the highest-heating trajectory with margin, dispersion, and greatest system mass, MSR-EES is predicted to experience the highest heat flux and pressure (approximately 3300 W/cm2 hot-wall, 200 kPa) of any earth entry vehicle todate. To verify performance requirements are met by the forebody TPS, the material must be tested to validate model predictions and give confidence to stakeholder’s expectation of performance. 3D Mid-Density Carbon Phenolic (3MDCP) is NASA’s baseline material for the forebody heatshield of the MSR-EES. As part of the arc jet campaign to evaluate material performance, recent testing has completed in the Interaction Heating Facility (IHF) using a new facility setting to achieve the necessary environments.

arcjet↗
NASA NTRSDate not supplied

Implementing the 3-D woven Mid-Density Carbon Phenolic (3MDCP) Heat Shield for the Mars Sample Return (MSR) Earth Entry Vehicle (EEV)

he Mars Sample Return (MSR)Program will return Martian soil samples to Earth in the early 2030s. Since the biological content of these samples is unknown, and potentially upsetting to Earth’s biosphere, the Earth Entry Vehicle (EEV) is required to be the most reliable entry probe ever devised. Entering Earth’s atmosphere at ~12 km/s, after up to a 6-day in-space free flight phase, the EEV must tolerate the cis-lunar Micro-Meteoroid environment, the near-Earth Orbital debris environment, and then entry heating of over 3,000 W/cm2 and pressures of250 kPa before ballistically impacting Earth’s surface at nearly 45 m/s. To reliably accomplish such a mission, NASA Ames is implementing the 3-D woven Mid-Density Carbon Phenolic (3MDCP) Heat Shield, derived from the prior Heatshield for Extreme Entry Environments(HEEET) material system [1]. 3MDCP development accomplishments to date, along with the future efforts to deliver the flight hardware are presented, along with a discussion of the manufacturing risks and accompanying mitigations achieved.

J C Vander Kam↗
NASA NTRS1991

Proceedings of the 7th Semiannual Meeting of the Nozzle Initiative Industry Advisory Committee on Standardization of Carbon-Phenolic Test Methods and Specifications

The application of carbon fibers and fabrics (CF) for producing rocket nozzles is discussed. These materials which are essential for fabricating the carbon composites used in aerospace systems gasify when exposed to high temperatures and the mechanical properties of the composites degrade. The oxidation kinetics under isothermal (IC) and non-isothermal (NIC) conditions are examined and a comparison is made between the characteristics of IC and NIC oxidation. Several CF, chars, and carbon blacks were examined, including a microporous char, a graphitized rayon fabric, and several carbonized rayon fabrics. A summary is given of the advantages and drawbacks of isothermal and non-isothermal oxidation of carbons. The proceedings are assembled in the form of a roundtable discussion.

Hall, William B.↗
NASA NTRS2015

Heatshield for Extreme Entry Environment Technology (HEEET) - Enabling Missions Beyond Heritage Carbon Phenolic

This poster provides an overview of the requirements, design, development and testing of the 3D Woven TPS being developed under NASA's Heatshield for Extreme Entry Environment Technology (HEEET) project. Under this current program, NASA is working to develop a Thermal Protection System (TPS) capable of surviving entry into Venus or Saturn. A primary goal of the project is to build and test an Engineering Test Unit (ETU) to establish a Technical Readiness Level (TRL) of 6 for this technology by 2017.

Carbon Phenolic↗
NASA NTRS2015

Heatshield for Extreme Entry Environment Technology (HEEET) Enabling Missions Beyond Heritage Carbon Phenolic

This poster provides an overview of the requirements, design, development and testing of the 3D Woven TPS being developed under NASAs Heatshield for Extreme Entry Environment Technology (HEEET) project. Under this current program, NASA is working to develop a Thermal Protection System (TPS) capable of surviving entry into Venus or Saturn. A primary goal of the project is to build and test an Engineering Test Unit (ETU) to establish a Technical Readiness Level (TRL) of 6 for this technology by 2017.

Venus↗