Effects of the Transport/Catalyst Layer Interface and Catalyst Loading on Mass and Charge Transport Phenomena in Polymer Electrolyte Membrane Water Electrolysis Devices
Not Available
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Not Available
Not Available
Abstract not provided
Not Available
The 67th AVS International Symposium and Exhibition, Virtual, October 24-29, 2021.
The behavior of the oxygen-evolving positive electrode (i.e. anode) in the anion exchange membrane water electrolyzer (AEMEL) is complex and influenced by several factors. Very few studies have been performed to understand oxygen evolution reaction (OER) behavior by optimizing the individual factors that influence performance. Here, this study highlights the effects of catalyst loading, catalyst selection, porous transport layer (PTL) type and conductive additive content. The influence of each factor is elucidated through a design of experiments (DoE) approach with a full statistical analysis. Electrochemical data, alongside Pareto charts, parametric trends and their mutual interactions are discussed. This DoE approach is also helpful in making useful predictions and discovering new combinations to be tested. The end result was a high-performance AEMEL able to operate at a current density of 1.0 A/cm 2 at 1.80 V with IrOx OER and PtNi hydrogen evolution reaction (HER) catalysts using 0.3 M KOH fed to the anode. Even lower operating voltage was observed with PbRuOx catalyst at the anode, 1.64 V @ 1.0 A/cm 2 , though the cell decay rate was higher. Lastly, a IrOx/PtNi cell was stably operated continuously for 30 days (720 h) at 1.0 A/cm 2 . This study can serve as a guide for optimal electrode design with insights into component-performance compromises, which can aid in making design choices and performing techno-economic analyses.
Here, we introduce a stochastic methodology to reproduce the complex pore structure observed in commercial iridium catalyst layers. This method preserves the α pore (pores smaller than 250 nm) and β pore (pores greater than or equal to 250 nm) regions of the catalyst layer. The morphology of the generated materials was validated by comparing the pore size distributions of generated materials against those obtained from commercial materials imaged using x-ray nano computed tomography. We further demonstrate that the pore size distributions of the generated materials are statistically indistinguishable from the imaged catalyst layers, indicating that the stochastic methodology is capable of accurately reproducing catalyst layer morphology. Pore network modelling was conducted on the generated catalyst materials to simulate single-phase permeability, electrical conductivity, and ionic conductivity, and these properties were found to be within experimentally measured ranges for electrolyzer catalyst layers. Additionally, simulations were performed on the generated materials with varying ionomer and iridium catalyst loadings. As the ionomer loading is added, proton conductivity increases exponentially, which demonstrates the importance of optimizing ionomer loading, considering that these effects will be exacerbated in the hydration and temperature conditions of operating electrolyzers. The stochastic material generation method presented in this work is a powerful tool for the development of novel low loading catalyst layers, where the effect of various structural parameters on electrolyzer performance characteristics can be explored.
Employing benchmarking metrics to capture the activity and stability of electrocatalysts for the oxygen evolution reaction (OER) in acid is a critical practice that enables meaningful comparison of catalyst material candidates reported throughout the literature. In this work, we find that ubiquitously used glassy carbon electrode substrates oxidize under typical OER operating conditions, forming a pacified, electrically insulating, and oxygen-rich surface layer that causes drastic loss of current density over the course of extended chronoamperometric stability tests at an anodic potential of 1.7 VRHE. We show that the experimentally observed stability of glassy carbon-based electrodes is approximately two orders of magnitude lower than that expected solely from dissolution-based catalyst intrinsic stability of Ir-based catalysts. We additionally find that glassy carbon-based electrode stability measured by chronoamperometric holds is greatly impacted by catalyst loading, with high catalyst loadings improving the stability of the overall electrode via a protective effect on the glassy carbon substrate. Altogether, our investigation highlights that glassy carbon is not electrochemically inert under OER conditions on the timescale of common stability tests, which can cause electrodes to exhibit performance losses that do not reflect the intrinsic stability of the actual catalyst material being investigated. In light of our findings, we underscore the usefulness of metrics, such as the S-number, to reflect intrinsic catalyst material stability.
CO 2 -assisted oxidative dehydrogenation of ethane is a sustainable alternative to steam cracking for ethylene production. In this study, a series of CeO 2 on SiO 2 supported NiFe 3 catalysts were synthesized by incipient wetness impregnation and tested for oxidative dehydrogenation performance. The CeO 2 /SiO 2 supported catalysts with high weight loading of CeO 2 (50%–75%) provided higher activity than the lower CeO 2 (0%–25%) loaded catalysts (with ethylene production rates of 0.62–0.98 µmol/g cat /s and 0.19–0.3 µmol/g cat /s, respectively) while maintaining high ethylene selectivity (43%–45%). In contrast, the NiFe 3 supported on only CeO 2 also exhibited high activity (ethylene production rate of 0.71 µmol/g cat /s), but the ethylene selectivity (16%) was greatly decreased compared to the mixed system. Temperature programmed reduction, X-ray diffraction, and Raman spectroscopy all indicate the creation of a solid solution of the Fe and Ni doped into the CeO 2 crystal structure in the catalysts with high CeO 2 loading/bulk CeO 2 support. Here, the high ethylene selectivity in the high CeO 2 loading catalysts indicates that the Fe is preferentially creating the solid solution, with the decrease in selectivity observed in the CeO 2 -only supported catalyst likely resulting from CeO 2 interacting directly with Ni, creating Ni-CeO X interfaces that are known active sites for the unwanted side reaction of dry reforming.
A modified chemical composition has been devised to improve the performance of the anode of a direct methanol fuel cell. The main feature of the modified composition is the incorporation of hydrous ruthenium oxide into the anode structure. This modification can reduce the internal electrical resistance of the cell and increase the degree of utilization of the anode catalyst. As a result, a higher anode current density can be sustained with a smaller amount of anode catalyst. These improvements can translate into a smaller fuel-cell system and higher efficiency of conversion. Some background information is helpful for understanding the benefit afforded by the addition of hydrous ruthenium oxide. The anode of a direct methanol fuel cell sustains the electro-oxidation of methanol to carbon dioxide in the reaction CH3OH + H2O--->CO2 + 6H(+) + 6e(-). An electrocatalyst is needed to enable this reaction to occur. The catalyst that offers the highest activity is an alloy of approximately equal numbers of atoms of the noble metals platinum and ruthenium. The anode is made of a composite material that includes high-surface-area Pt/Ru alloy particles and a proton-conducting ionomeric material. This composite is usually deposited onto a polymer-electrolyte (proton-conducting) membrane and onto an anode gas-diffusion/current-collector sheet that is subsequently bonded to the proton-conducting membrane by hot pressing. Heretofore, the areal density of noble-metal catalyst typically needed for high performance has been about 8 mg/cm2. However, not all of the catalyst has been utilized in the catalyzed electro-oxidation reaction. Increasing the degree of utilization of the catalyst would make it possible to improve the performance of the cell for a given catalyst loading and/or reduce the catalyst loading (thereby reducing the cost of the cell). The use of carbon and possibly other electronic conductors in the catalyst layer has been proposed for increasing the utilization of the catalyst by increasing electrical connectivity between catalyst particles. However, the relatively low density of carbon results in thick catalyst layers that impede the mass transport of methanol to the catalytic sites. Also, the electrical conductivity of carbon is less than 1/300th of typical metals. Furthermore, the polymer-electrolyte membrane material is acidic and most metals are not chemically stable in contact with it. Finally, a material that conducts electrons (but not protons) does not contribute to the needed transport of protons produced in the electro-oxidation reaction.
Abstract Symmetric‐structure metal‐supported solid oxide fuel cells (MS‐SOFCs) are fabricated by infiltrating catalysts on both anode and cathode side. Various aspects of the infiltration process are optimized. Performance is found to be sensitive to precursor dilution, catalyst loading, and catalyst calcining temperature. For an optimized cell with lanthanum strontium manganite (LSM) as cathode and Sm 0.2 Ce 0.8 O 2− δ mixed with Ni (SDCN) as anode, peak power densities of 0.44, 1.1, and 1.9 W cm −2 are achieved at 600, 700, and 800 °C, respectively. A fully symmetric MS‐SOFC with SDCN as both the anode and cathode sides achieves moderate peak power densities of 0.12, 0.37, and 0.76 W cm −2 at 600, 700, and 800 °C, respectively. A solvent‐based infiltration technique is also explored and found to be more effective than capillary forces alone but not as effective as vacuum infiltration.
Tantalum nitride (Ta 3 N 5 ) has gained significant attention as a potential photoanode material, yet it has been challenged by material quality issues. Defect-induced trap states are detrimental to the performance of any semiconductor material. Beyond influencing the performance of Ta 3 N 5 films, defects can also accelerate the degradation in water during desired electrochemical applications. Defect passivation has provided an enormous boost to the development of many semiconductor materials but is currently in its infancy for Ta 3 N 5 . This is in part due to a lack of experimental understanding regarding the spatial and energetic distribution of trap states throughout Ta 3 N 5 thin films. Here, we employ drive-level capacitance profiling (DLCP) to experimentally resolve the spatial and energetic distribution of trap states throughout Ta 3 N 5 thin films. The density of deeper energetic traps is found to reach ∼2.5 to 6 × 10 22 cm –3 at the interfaces of neat Ta 3 N 5 thin films, over an order of magnitude greater than the bulk. In addition to the spatial profile of deep trap states, we report neat Ta 3 N 5 thin films to be highly n-type in nature, owning a free carrier density of ∼9.74 × 10 17 cm –3 . This information, coupled with the present understanding of native oxide layers on Ta 3 N 5 , has facilitated the rational design of a targeted passivation strategy that simultaneously provides a means for catalyst immobilization. Loading catalyst via silatrane moieties suppresses the density of defects at the surface of Ta 3 N 5 thin films by two orders of magnitude, while also reducing the free carrier density of films by over one order of magnitude, effectively dedoping the films to ∼2.40 × 10 16 cm –3 . The surface passivation of Ta 3 N 5 films translates to suppressed defect-induced trapping and recombination of photoexcited carriers, as determined through absorption, photoluminescence, and transient photovoltage. Here, this illustrates how developing a deeper understanding of the distribution and influence of defects in Ta 3 N 5 thin films has the potential to guide future works and ultimately accelerate the integration and development of high-performance Ta 3 N 5 thin film devices.
Human exploration missions to Mars and other destinations beyond low Earth orbit require highly robust, reliable, and maintainable life support systems that maximize recycling of water and oxygen. In order to meet this requirement, NASA has continued the development of a Series-Bosch System, a two stage reactor process that reduces carbon dioxide (CO2) with hydrogen (H2) to produce water and solid carbon. Theoretically, the Bosch process can recover 100% of the oxygen (O2) from CO2 in the form of water, making it an attractive option for long duration missions. The Series Bosch system includes a reverse water gas shift (RWGS) reactor, a carbon formation reactor (CFR), an H2 extraction membrane, and a CO2 extraction membrane. In 2016, the results of integrated testing of the Series Bosch system showed great promise and resulted in design modifications to the CFR to further improve performance. This year, integrated testing was conducted with the modified reactor to evaluate its performance and compare it with the performance of the previous configuration. Additionally, a CFR with the capability to load new catalyst and remove spent catalyst in-situ was built. Flow demonstrations were performed to evaluate both the catalyst loading and removal process and the hardware performance. The results of the integrated testing with the modified CFR as well as the flow demonstrations are discussed in this paper.
Human exploration missions to Mars and other destinations beyond low Earth orbit require highly robust, reliable, and maintainable life support systems that maximize recycling of water and oxygen. In order to meet this requirement, NASA has continued the development of a Series-Bosch System, a two stage reactor process that reduces carbon dioxide (CO2) with hydrogen (H2) to produce water and solid carbon. Theoretically, the Bosch process can recover 100% of the oxygen (O2) from CO2 in the form of water, making it an attractive option for long duration missions. The Series Bosch system includes a reverse water gas shift (RWGS) reactor, a carbon formation reactor (CFR), an H2 extraction membrane, and a CO2 extraction membrane. In 2016, the results of integrated testing of the Series Bosch system showed great promise and resulted in design modifications to the CFR to further improve performance. This year, integrated testing was conducted with the modified reactor to evaluate its performance and compare it with the performance of the previous configuration. Additionally, a CFR with the capability to load new catalyst and remove spent catalyst in-situ was built. Flow demonstrations were performed to evaluate both the catalyst loading and removal process and the hardware performance. The results of the integrated testing with the modified CFR as well as the flow demonstrations are discussed in this paper.
The effective management of plastic waste streams to prevent plastic land and water pollution is a growing problem that is also one of the most important challenges in polymer science today. Polymer materials that are stable over their lifetime and can also be cheaply recycled or repurposed as desired could more easily be diverted from waste streams. However, this is difficult for most commodity plastics. It is especially difficult to conceive this with intractable, cross-linked polymers such as rubbers. In this work, we explore the utility of microencapsulated Grubbs’ catalysts for the in-situ depolymerization and reprocessing of polybutadiene (PB) rubber. Second-generation Hoveyda-Grubbs catalyst (HG2) contained within glassy thermoplastic microspheres can be dispersed in PB rubber below the microsphere’s glass transition temperature (T g ) without adverse depolymerization, evidenced by rubber with and without these microspheres obtaining similar shear storage moduli of ≈16 and ≈28 kPa, respectively. The thermoplastic’s T g can be used to tune the depolymerization temperature, via release of HG2 into the rubber matrix. For example, using poly(lactic acid) (PLA) vs polysulfone results in an 85 and 162 °C depolymerization temperature, respectively. Liquefaction of rubber to a mixture of small molecules and oligomers is demonstrated using a 0.01 mol % catalyst loading using PLA as the encapsulant. Furthermore, at that same catalyst loading, depolymerization occurs to a greater extent in comparison to two ex-situ approaches, including a conventional solvent-assisted method, where it occurs at roughly twice the extent at each given catalyst loading. In addition, depolymerization of the microsphere-loaded rubbers was demonstrated for samples stored under nitrogen for 23 days. Lastly, we show that the depolymerized products can be reprocessed back into solid rubber with a shear storage modulus of ≈32 kPa. Thus, we envision that this approach could be used to recycle and reuse cross-linked rubbers at the end of their product lifetime.
A rationalized interfacial design strategy was applied to tailor the porous transport layer (PTL)-catalyst layer (CL) contact and the PTL bulk-phase architecture. Particularly, at the PTL-CL interface, our results reveal that laser ablated sintered titanium power-based PTLs improve electrolyzer performance at both the H2NEW Consortium baseline catalyst loading of 0.4 mgIr cm -2 as well as at the ultra-low catalyst loading of 0.055 mgIr cm -2 . Under ultra-low catalyst loadings, the laser ablated PTL demonstrates maximum reduction of 230 mV compared to the commercial PTL at 4 A cm -2 , and reduces by 68 mV at 3.2 A cm -2 under H2NEW baseline loading. Laser ablation alters the titanium phase at the interface, so it forms more uniform structure like a microporous layer or a backing layer, leading to an increase in the surface area in contact with the catalyst layer while preventing the membrane from deforming into the PTL. Moreover, we reveal that bulk-phase architecture modification of the PTL by ablating patterned pores at the flow field-PTL interface improves mass transport without sacrificing contact at the CL-PTL interface. Overall, laser ablation of the PTL is an effective method to customize interfacial design to enhance proton exchange membrane electrolyzer performance.