Search NASA⌕ Search

SEARCH · Search NASA

Results for “coefficient values thermal conductivity electrical resistivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

22 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Nickel-Graphite Composite Compliant Interface and/or Hot Shoe Material

Next-generation high-temperature thermoelectric-power-generating devices will employ segmented architectures and will have to reliably withstand thermally induced mechanical stresses produced during component fabrication, device assembly, and operation. Thermoelectric materials have typically poor mechanical strength, exhibit brittle behavior, and possess a wide range of coefficient of thermal expansion (CTE) values. As a result, the direct bonding at elevated temperatures of these materials to each other to produce segmented leg components is difficult, and often results in localized microcracking at interfaces and mec hanical failure due to the stresses that arise from the CTE mismatch between the various materials. Even in the absence of full mechanical failure, degraded interfaces can lead to increased electrical and thermal resistances, which adversely impact conversion efficiency and power output. The proposed solution is the insertion of a mechanically compliant layer, with high electrical and thermal conductivity, between the low- and high-temperature segments to relieve thermomechanical stresses during device fabrication and operation. This composite material can be used as a stress-relieving layer between the thermoelectric segments and/or between a thermoelectric segment and a hot- or cold-side interconnect material. The material also can be used as a compliant hot shoe. Nickel-coated graphite powders were hot-pressed to form a nickel-graphite composite material. A freestanding thermoelectric segmented leg was fabricated by brazing the compliant pad layer between the high-temperature p- Zintl and low-temperature p-SKD TE segments using Cu-Ag braze foils. The segmented leg stack was heated in vacuum under a compressive load to achieve bonding. The novelty of the innovation is the use of composite material that re duces the thermomechanical stresses en - countered in the construction of high-efficiency, high-temperature therm - o-electric devices. The compliant pad enables the bonding of dissimilar thermoelectric materials while maintaining the desired electrical and thermal properties essential for efficient device operation. The modulus, CTE, electrical, and thermal conductances of the composite can be controlled by varying the ratio of nickel to graphite.

Firdosy, Samad A.↗
NASA NTRS1975

The time and temperature dependence of the thermoelectric properties of silicon-germanium alloy

Experimental data on the electrical resistivity and Seebeck coefficient of n-type and p-type silicon-germanium alloys are analyzed in terms of a solid-state dopant precipitation model proposed by Lifshitz and Slyozov (1961). Experimental findings on the time and temperature dependence of the thermal conductivity of these two types of alloy indicate that the thermal conductivity of silicon-germanium alloys changes with time, contrary to previous hypothesis. A preliminary model is presented which stipulates that the observed thermal conductivity decrease in silicon-germanium alloys is due partly to dopant precipitation underlying the electrical property changes and partly to enhanced alloying of the material. It is significant that all three properties asymptotically approach equilibrium values with time. Total characterization of these properties will enable the time change to be fully compensated in the design of a thermoelectric device employing silicon-germanium alloys.

Raag, V.↗
DOE OSTI2021

Two Polymorphs of BaZn 2 P 2 : Crystal Structures, Phase Transition, and Transport Properties

Here, the novel α-BaZn 2 P 2 structural polymorph has been synthesized and structurally characterized for the first time. Its structure, elu-cidated from single crystal X-ray diffraction, indicates that the compound crystallizes in the orthorhombic α-BaCu 2 S 2 structure type, with unit cell parameters a = 9.7567(14) Å, b = 4.1266(6) Å, and c = 10.6000(15) Å. With β-BaZn 2 P 2 being previously iden-tified as belonging to the ThCr 2 Si 2 family, and with the precedent of structural phase transitions between the α-BaCu 2 S 2 type and the ThCr 2 Si 2 type, the potential for the pattern to be extended to the two different structural forms of BaZn 2 P 2 was explored. Thermal analysis suggest that a first order phase transition occurs at ~1123 K, whereby the low-temperature orthorhombic α-phase transforms to a high-temperature tetragonal β-BaZn 2 P 2 ; the structure of which was also studied and confirmed by single-crystal X-ray diffraction. Preliminary transport properties and band structure calculations indicate that α-BaZn 2 P 2 is a p-type, narrow-gap semiconductor with a direct bandgap (Eg) of 0.5 eV. The Seebeck coefficient, S(T), for the material increases steadily from the room temperature value of 119 µV/K to 184 µV/K at 600 K. The electrical resistivity of α-BaZn 2 P 2 is relatively high, on the order of 40 mΩ·cm, and the ρ(T) dependence shows gradual decrease upon heating. Such behavior is comparable to those of the typical semimetals or degenerate semiconductors. Although the observed values of the as-synthesized samples are not optimal, the carrier concentration can apparently be tuned to fall between the values of metals and semiconductors, thus providing an open window for optimizing this phase towards achieving an enhanced thermoelectric figure of merit zT. The calculated indirect band gap for the β-BaZn 2 P 2 phase is Eg = 0.03 eV which is about an order of magnitude lower than that of α-BaZn 2 P 2 . It is expected that the cage-like structural motif and layered structure possessed by α-BaZn 2 P 2 and β-BaZn 2 P 2 phases, respectively, would promote the realiza-tion of a low thermal conductivity in both compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Theoretical predictive screening of noble-metal-containing M 3 AuC 2 (M = Ti, V, and Cr) MAX phases

Using first-principles density functional theory (DFT), the ground state physical properties of the newly synthesized noble-metal-containing Ti 3 AuC 2 MAX phase have been investigated. The effect of transition-element Ti replacement (V and Cr) on physical properties, including structural, elastic, electronic, thermal, and optical are presented. The optimized lattice parameters of Ti 3 AuC 2 MAX phase are in good agreement with the experimental values and decrease when we replace Ti with V and then Cr. The magnetic properties of M 3 AuC 2 are predicted by using generalized gradient approximation (GGA) incorporating onsite electron correlation parameter (Hubbard U parameter) within DFT. Out of three studied MAX phases, V 3 AuC 2 and Cr 3 AuC 2 phases exhibit magnetism. The thermodynamical stability of M 3 AuC 2 (M = Ti, V, and Cr) phases is discussed by the formation enthalpy with respect to their most competing phases. The electronic structure reveals that these phases have metallic nature and are electrically anisotropic. The M-element replacement has an effect on the bonding properties of M 3 AuC 2 . The bonding between M-C is in the order of Cr 3 AuC 2 > V 3 AuC 2 > Ti 3 AuC 2 according to their peak positions and heights of density of states in the occupied site, which is also confirmed from the charge density distribution. The elastic properties indicate that M 3 AuC 2 phases are ductile, machinable, less stiff, and better resistant to thermal shock and are elastically anisotropic. To understand the properties of M 3 AuC 2 for the extreme environment, we employed a quasi-harmonic Debye model at the pressure and temperature range of 0–50 GPa and 0–1600 K, respectively. Additionally, we evaluated thermal conductivity and melting temperature to further understand the potential of these MAX phases in coating applications at elevated temperature. In relation to optical properties, these MAX phases have a reasonable absorption coefficient in the visible as well as in the ultra-violet regions. The reflectivity of M 3 AuC 2 phases is polarization dependent and of 45 % against the visible region, which reveals its potential as coating material to minimize solar heating.

312 MAX phases↗