Search NASA⌕ Search

SEARCH · Search NASA

Results for “cold injection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Stability study of aqueous foams under high-temperature and high-pressure conditions relevant to Enhanced Geothermal Systems (EGS)

In Enhanced Geothermal System (EGS) hydraulic fracturing is carried out by injecting cold water into deep Hot Dry Rocks (HDR) under carefully controlled conditions to create new or reopen existing fractures. Water-based fracturing fluids demonstrate some challenges including immense quantity of water usage, water sensitivity of the formations, water blocking, and lack of proppant carrying capacity and transportation. Thus, an alternative is to use foam-based fracturing fluid which offers potential advantage over conventional water-based fracturing fluid such as minimum water usage, reduced wellbore damage, high proppant carrying capacity, and less environmental damage. However, foams are complex mixture of gaseous phase and liquid phase which are thermodynamically unstable at downhole conditions, and their stability can decrease over time due to liquid drainage, bubble coarsening, and coalescence. This paper shows laboratory experiments executed to study foam stability at high temperature (200°C) and high pressure (6.9MPa) conditions which simulates the geothermal environment. Foam stability was characterized by half-life of foam, which is defined as the time taken by the foam to decreases by 50% of its original height due to drainage. In this paper, two types of gaseous phases, nitrogen (N 2 ) and carbon dioxide (CO 2 ) were investigated. Also, based on successful practice of foam-based fracturing fluid in oil and gas industries, four surfactants, including Alpha olefin sulfonate (AOS), Sodium dodecyl sulfonate (SDS), Tergitol™ (NP – 40), and Cetyltrimethylammonium chloride (CTAC) at optimum concentration of 1wt.% were tested for best stability performance. In addition, different stabilizing agents including guar gum, bentonite clay, crosslinker, silicon dioxide nanoparticles (SiO 2 ), graphene oxide (GO) were also studied. Experimental results showed that N 2 foams were more stable than CO 2 foams. It was observed that foam half-life decreased with the increase in temperature. Among all the surfactants, AOS foams showed the most promising thermal stability at high temperatures. Moreover, with the addition of stabilizing agents, foam's half-life was enhanced. Stabilizing agents such as crosslinker and GO dispersion showed the most stable foams with half-life recorded at 20min and 17min, respectively, at 200°C and 6.9MPa. Finally, pressure also showed a positive effect on foam stability; with increased pressure, foam half-life was increased. Based on the experimental data, analytical models for the effect of temperature and pressure were developed, considering foam degradation is a first-order kinetic reaction that linearly depends on the foam drainage mechanism. The effect of temperature on foam half-life was studied as an exponential decay model. In this model, foam half-life is a function of drainage rate constant (D A ) and activation energy (E a ) of the foam system. The effect of pressure on foam half-life was found to obey a power-law model where an increase in pressure showed an increase in foam half-life. Furthermore, a linear relation was studied for the effect of pressure on foam activation energy and drainage rate. Then the combined effects of temperature and pressure were studied, which yielded an analytical model to predict the foam stabilities in terms of half-life for different foam compositions. In conclusion, this research indicates that with an appropriate selection of surfactants and stabilizing agents, it is possible to obtain stable foams, which could replace conventional water fracturing fluid under EGS conditions.

15 GEOTHERMAL ENERGY↗

Aerothermodynamics of the Space Shuttle reaction control system.

Based on experimental data, the aerothermodynamic surface environment for the Space Shuttle Orbiter reaction control system (RCS) thrusters during entry was established. Using this environment the required thermal protection for the RCS thruster nozzles and surrounding vehicle surfaces on the orbiter nose was determined. Wind tunnel test data was obtained at Mach 8 to measure the heat transfer and pressure distribution in separated flow due to deep, three-dimensional cavities and lateral jet interference using helium and air (hot and cold) injection from a supersonic nozzle. Results of the analysis and correlation of the test data are presented.

Brevig, O.↗

Emission Spectroscopic Measurements in the Plenum Region of the NASA IHF Arc Jet Facility

A newly designed segment with optical access was installed in the plenum chamber of the 60 MW Interaction Heating arcjet Facility at NASA Ames Research Center. This special segment has ports located off axis, and the optical fibers can be inserted into these ports. The special segment allows for optical examination of the arc-heated flow as it enters the plenum, and thus assists in determining estimates of the thermodynamic state of the inflow to the convergent section of the nozzle. In the present work, optical emission measurements have been made in VIS-NIR region (wavelengths between 500 nm to 900 nm) for two settings of the arc heater - a 6000 A condition (high condition) with the minimum amount of radial injection of cold air in the plenum, and a 3300 A condition (low condition) with significant amount of cold air injection to reduce the enthalpy of the arc-heated stream. The results presented here were obtained using an Acton SP300i spectrometer coupled to a Princeton Instruments PI-max intensified camera. In addition to the optical emission measurements, computations were performed for the flow in the plenum and radiation along lines of sight corresponding to the optical ports. Along the centerline, i.e., the longest line of sight across the plenum cross-section, there is good agreement between computations and measurements for the high enthalpy condition, although the off-axis radial profiles show some differences. For the low enthalpy condition, there are significant differences between computations and measurements. The current working hypothesis is that the computational model does not capture details of the mixing process in the plenum.

Winter, Michael W.↗

Method and apparatus to produce high specific impulse and moderate thrust from a fusion-powered rocket engine

A system and method for producing and controlling high thrust and desirable specific impulse from a continuous fusion reaction is disclosed. The resultant relatively small rocket engine will have lower cost to develop, test, and operate that the prior art, allowing spacecraft missions throughout the planetary system and beyond. The rocket engine method and system includes a reactor chamber and a heating system for heating a stable plasma to produce fusion reactions in the stable plasma. Magnets produce a magnetic field that confines the stable plasma. A fuel injection system and a propellant injection system are included. The propellant injection system injects cold propellant into a gas box at one end of the reactor chamber, where the propellant is ionized into a plasma. The propellant and fusion products are directed out of the reactor chamber through a magnetic nozzle and are detached from the magnetic field lines producing thrust.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Deep Learning for Modeling Enhanced Geothermal Systems

Enhanced Geothermal Systems (EGS) offer a vast potential to expand the use of geothermal energy. Heat is extracted from this engineered system by injecting cold water into a subsurface fractures, which are in contact with the hot dry rock, and pulled through the production wells. Creating EGS requires improving the natural permeability of hot crystalline rocks. To develop economically viable EGS reservoirs, significant technical barriers (e.g., better stimulation technologies without adequate water and/or permeability) and non-technical barriers (e.g., land access and permitting) must be overcome. In this short conference paper, we present a workflow to address a part of this challenge – “How to develop economically viable EGS using existing technologies?”. Our workflow called the GeoThermalCloud (GTC) for EGS, leverages recent advances in machine learning, deep learning, and cloud computing. This GTC framework is open-source and available at https://github.com/SmartTensors/GeoThermalCloud.jl. The GTC framework provides trained deep learning (DL) models to estimate the net present value of a given EGS design scenario. The Geothermal Design Tool (https://github.com/GeoDesignTool/GeoDT.git), a fast and simplified multi-physics solver, is used to develop a database for training DL models. The database consists of EGS design parameters (inputs to DL model) and their net present value (output of DL model) in uncertain geologic systems. The EGS design parameters for constructing this training database are based on Utah FORGE but include the options of more wells and deeper depths. The DL models are trained by ingesting the EGS design parameters and estimating the corresponding net present value. Such an emulation allows us to screen various EGS designs quickly and identify good development strategies by coupling them with optimization techniques. Our preliminary results show promise in DL emulation of net present value. However, a lot more work is needed to improve the predictive capability of DL models (i.e., extensive hyperparameter tuning is necessary). This will be the primary focus of our future work.

artificial neural networks, geothermal↗

Cavity morphology in a Ni based superalloy under heavy ion irradiation with cold pre-injected helium. I

In order to understand radiation damage in the nickel based superalloy Inconel X-750 in thermal reactors, where (n, α) transmutation reaction also occurred in addition to fast neutron induced atomic displacement, heavy ion (1 MeV Kr{sup 2+}) irradiation with pre-injected helium was performed under in-situ observations of an intermediate voltage electron microscope at Argonne National Laboratory. By comparing to our previous studies using 1 MeV Kr{sup 2+} irradiation solely, the pre-injected helium was found to be essential in cavity nucleation. Cavities started to be visible after Kr{sup 2+} irradiation to 2.7 dpa at ≥200 °C in samples containing 200 appm, 1000 appm, and 5000 appm helium, respectively, but not at lower temperatures. The cavity growth was observed during the continuous irradiation. Cavity formation appeared along with a reduced number density of stacking fault tetrahedra, vacancy type defects. With higher pre-injected helium amount, a higher density of smaller cavities was observed. This is considered to be the result of local trapping effect of helium which disperses vacancies. The average cavity size increases with increasing irradiation temperatures; the density reduced; and the distribution of cavities became heterogeneous at elevated temperatures. In contrast to previous characterization of in-reactor neutron irradiated Inconel X-750, no obvious cavity sink to grain boundaries and phase boundaries was found even at high doses and elevated temperatures. MC-type carbides were observed as strong sources for agglomeration of cavities due to their enhanced trapping strength of helium and vacancies.

36 MATERIALS SCIENCE↗

PROTON HEATING BY PICK-UP ION DRIVEN CYCLOTRON WAVES IN THE OUTER HELIOSPHERE: HYBRID EXPANDING BOX SIMULATIONS

Using a one-dimensional hybrid expanding box model, we investigate properties of the solar wind in the outer heliosphere. We assume a proton–electron plasma with a strictly transverse ambient magnetic field and, aside from the expansion, we take into account the influence of a continuous injection of cold pick-up protons through the charge-exchange process between the solar wind protons and hydrogen of interstellar origin. The injected cold pick-up protons form a ring distribution function, which rapidly becomes unstable, and generate Alfvén cyclotron waves. The Alfvén cyclotron waves scatter pick-up protons to a spherical shell distribution function that thickens over that time owing to the expansion-driven cooling. The Alfvén cyclotron waves heat solar wind protons in the perpendicular direction (with respect to the ambient magnetic field) through cyclotron resonance. At later times, the Alfvén cyclotron waves become parametrically unstable and the generated ion-acoustic waves heat protons in the parallel direction through Landau resonance. The resulting heating of the solar wind protons is efficient on the expansion timescale.

79 ASTRONOMY AND ASTROPHYSICS↗

Investigation of fuel film formation and soot emissions in a GDI engine during cold-start with Split-injection strategies

This study investigates the impact of fuel-film formation on engine-out soot emissions in a gasoline direct injection (GDI) engine under cold-start conditions. Split-injection strategies were applied by varying the number of injections, injection duration, and total fuel quantity to affect wall wetting and control the average in-cylinder equivalence ratio. A combined experimental and numerical approach was employed to analyze fuel-film deposition, combustion efficiency, and engine-out soot and unburnt hydrocarbons (UHC) emissions. In particular, fuel film distribution estimated by means of non-reacting, 3-D, computational fluid dynamics (CFD) simulations, together with experimentally measured soot data, were used to investigate fuel film formation and its role in soot generation. In the experiments, a skip-fired engine control strategy was applied to mimic the transient nature of engine cold-start operation. The results indicate that, under the same total number of injections, increasing the average in-cylinder equivalence ratio through longer injection durations improves combustion stability, as indicated by the decrease of the coefficient of variation of IMEP n (Net Indicated Mean Effective Pressure) from 6.0 % to 0.6 %. However, this strategy leads to higher soot emissions, which increased by nearly an order of magnitude, primarily due to enhanced wall-film formation. In contrast, increasing the number of injections while maintaining a constant equivalence ratio significantly impacts fuel-film deposition and, consequently, soot emissions, with a fivefold reduction of the measured engine-out soot, decreasing from 3.5 mg to 0.7 mg. A soot-film correlation was developed and achieved a high coefficient of determination (r 2 = 0.95) and was further extended to account for spark timing effects. These findings confirm the effectiveness of split-injection for avoiding wall film formation and soot emissions, and the critical role of fuel film in soot generation, supporting the hypothesis that pool fires play a crucial role in contributing to soot formation under these cold-start conditions. In conclusion, the study also indicates the value of a predictive soot-film correlation for developing cold-start emission control strategies.

Engine Cold-start↗

A comparison between an empirical technique for the prediction of cyclogenesis and the LFM II

Preliminary empirical results are given of a study to determine the present-day utility of the George (1960) technique for predicting cyclogenesis. Surface and constant pressure charts are examined to determine the frequency and preferred locations for the occurrence of cold air injections. The accuracy of the empirical technique and the LFM II are compared for a limited number of cases. No consistent relationship between cold air injections and other atmospheric features is found. After the appearance of a cold air injection, cyclogenesis, a center jump, or a deepening of an existing cyclone occurs 77% of the time.

Atlas, R.↗

Advancing Reactive Tracer Methods for Measurement of Thermal Evolution in Geothermal Reservoirs (Final Report)

The injection of cold fluids into engineered geothermal system (EGS) and conventional geothermal reservoirs may be done to help extract heat from the subsurface or to maintain pressures within the reservoir (e.g., Rose et al., 2001). As these injected fluids move along fractures, they acquire heat from the rock matrix and remove it from the reservoir as they are extracted to the surface. A consequence of such injection is the migration of a cold-fluid front through the reservoir (Figure 1) that could eventually reach the production well and result in the lowering of the temperature of the produced fluids (thermal breakthrough). Efficient operation of an EGS as well as conventional geothermal systems involving cold-fluid injection requires accurate and timely information about thermal depletion of the reservoir in response to operation. In particular, accurate predictions of the time to thermal breakthrough and subsequent rate of thermal drawdown are necessary for reservoir management, design of fracture stimulation and well drilling programs, and forecasting of economic return. A potential method for estimating migration of a cold front between an injection well and a production well is through application of reactive tracer tests, using chemical whose rate of degradation is dependent on the reservoir temperature between the two wells (e.g., Robinson 1985). With repeated tests, the rate of migration of the thermal front can be determined, and the time to thermal breakthrough calculated. While the basic theory behind the concept of thermal tracers has been understood for some time, effective application of the method has yet to be demonstrated. This report describes results of a study that used several methods to investigate application of reactive tracers to monitoring the thermal evolution of a geothermal reservoir. These methods included (1) mathematical investigation of the sensitivity of known and hypothetical reactive tracers, (2) laboratory testing of novel tracers that would improve method sensitivity, (3) development of a software tool for design and interpretation of reactive tracer tests and (4) field testing of the reactive tracer temperature monitoring concept.

15 GEOTHERMAL ENERGY↗

Hydraulic Response to Thermal Stimulation Efforts at Raft River Based on Stepped Rate Injection Testing

The injection well stimulation project at the Raft River geothermal field tests the effect of long-term cold water injection and high pressure injection on well injectivity, improvements to which could reduce operating costs. The primary data for analysis and interpretation of the injection test are step-rate flow tests run before each new phase of the injection. These tests were analyzed using a combination of standard pump-test analytical solution methods and methods developed expressly for the observed conditions. The stepped rate injection tests, combined with long-term flow and pressure response data suggest that the well is located within a fractured formation of low transmissivity but high storativity. These calculated parameters appeared to increase with pressure during the first injection test and the higher values were reproduced during the second stepped rate test. Calculated transmissivity and storativity are on the order of 4E-5 m cm 2 and 1E-4 m Pa -1 , respectively. The apparent pressure dependence of fitted hydraulic parameters may reflect near-well fracture compliance that increased the effective radius of the wellbore during the first test. While the type curve fit analysis also suggests that the reservoir behaves as a uniformly fractured reservoir with a radial flow regime, the hydraulic parameters indicate that condition may exist only a very limited distance (<10 m) from the well. Longer-term pressure response suggests that flow in the system effectively reaches steady state in a period of less than a day, which may reflect pressure stabilization resulting from pressure-dependent permeability or a region of much higher permeability located with a few meters of the well. The transmissivity estimates obtained from this analysis, converted to approximate fracture density and aperture, provide useful constraints on the distance to which the thermal front may migrate from the well during the cold water injection phase of the stimulation project. We estimate that the cooling front will migrate less than a tenth of a kilometer over an approximately one-year injection period. Here, the effects of that cooling, however, may be substantial, because increases in permeability have maximum effect nearest the well.

cold water injection↗

Large-Scale Mini-Magnetosphere Plasma Propulsion (M2P2) Experiments

Mini-Magnetosphere Plasma Propulsion (M2P2) is an innovative plasma propulsion system that has the potential to propel spacecraft at unprecedented speeds of 50 to 80 km/s, with a low power requirement of approx. 1 kW per 100 kg of payload and -1 kg of neutral gas [fuel] consumption per day of acceleration. Acceleration periods from several days to a few months are envisioned. High specific impulse and efficiency are achieved through coupling of the spacecraft to the 400 km/s. solar wind through an artificial magnetosphere. The mini-magnetosphere or inflated magnetic bubble is produced by the injection of cold dense plasma into a spacecraft-generated magnetic field envelope. Magnetic bubble inflation is driven by electromagnetic processes thereby avoiding the material and deployment problems faced by mechanical solar sail designs. Here, we present the theoretical design of M2P2 as well as initial results from experimental testing of an M2P2 prototype demonstrating: 1) inflation of the dipole magnetic field geometry through the internal injection of cold plasma; and 2) deflection of and artificial solar wind by the prototype M2P2 system. In addition, we present plans for direct laboratory measurement of thrust imparted to a prototype M2P2 by an artificial solar wind during the summer of 2001.

Winglee, R. M.↗

Large-Scale Mini-Magnetosphere Plasma Propulsion (M2P2) Experiments

Mini-Magnetosphere Plasma Propulsion (M2P2) is an innovative plasma propulsion system that has the potential to propel spacecraft at unprecedented speeds of 50 to 80 km per second with a low-power requirement of approx. 1 kW per 100 kg of payload and approx. 1 kg of neutral gas [fuel] consumption per day of acceleration. Acceleration periods from several days to a few months are envisioned. High specific impulse and efficiency are achieved through coupling of the spacecraft to the 400 km per second solar wind through an artificial magnetosphere. The mini-magnetosphere or inflated magnetic bubble is produced by the injection of cold dense plasma into a spacecraft-generated magnetic field envelope. Magnetic bubble inflation is driven by electromagnetic processes thereby avoiding the material and deployment problems faced by mechanical solar sail designs, Here, we present the theoretical design of M2P2 as well as initial results from experimental testing of an M2P2 prototype demonstrating: 1) inflation of the dipole magnetic field geometry through the internal injection of cold plasma; and 2) deflection of and artificial solar wind by the prototype M2P2 system. In addition, we present plans for direct laboratory measurement of thrust imparted to a prototype M2P2 by an artificial solar wind during the summer of 2001.

Winglee, R. M.↗

Evaluation of Stimulation by Shear Slip in Fractured Rock Using a 3D Coupled Thermo-Poro-Mechanical FEM

This paper presents a 3D finite element model for simulating shear slip on fractures in rock in response to coupled thermo-poro-mechanical processes. The modeling is part of a broader effort to investigate the role of pore pressure and cooling by cold water injection on shear slip and permeability increase in granitic rock using laboratory shearing experiments under triaxial conditions. In particular, 3D thermo-poro-mechanical finite element modeling and analysis of injection experiment in fractured rock has been carried out to analyze the role of pore pressure, temperature, fracture deformation and their interactions. 4-noded tetrahedral elements are employed for intact rock deformation and transport processes within the matrix. To represent the mechanical response of a fracture surface, zero thickness contact interface element is developed based on recently developed element partitioning algorithm and procedures for applying hydraulic pressure on the fracture surfaces. A Mohr-Coulomb type criterion is adapted to capture the slip on the fracture and to quantify its reversible and irreversible deformation. The numerical model has been calibrated using results from well controlled, advanced laboratory experiments. Excellent agreement between modeling and experimental observations is achieved. Simulation results illustrate that pore pressure increase and rock matrix/fracture surface cooling cause the fracture system to deform and slip. Fracture slip is promoted due to its normal stress reduction associated with cooling effect of cold fluid injection. The numerical model provides a physics-based understanding of the role of coupled processes on shear stimulation phenomenon and the resulting permeability enhancement.

58 GEOSCIENCES↗

The Northwest Geysers EGS Demonstration Project, California. Pre-stimulation Modeling and Interpretation of the Stimulation

The Northwest Geysers Enhanced Geothermal System (EGS) demonstration project aims to create an EGS by directly and systematically injecting cool water at relatively low pressure into a known High Temperature (280–400 °C) Zone (HTZ) located under the conventional (240 °C) geothermal steam reservoir at The Geysers geothermal field in California. Here we report that , the results of coupled thermal, hydraulic, and mechanical (THM) analyses made using a model developed as part of the pre-stimulation phase of the EGS demonstration project is presented. The model simulations were conducted in order to investigate injection strategies and the resulting effects of cold-water injection upon the EGS system; in particular to predict the extent of the stimulation zone for a given injection schedule. The actual injection began on October 6, 2011, and in this paper a comparison of pre-stimulation model predictions with micro-earthquake (MEQ) monitoring data over the first few months of a one-year injection program is presented. The results show that, by using a calibrated THM model based on historic injection and MEQ data at a nearby well, the predicted extent of the stimulation zone (defined as a zone of high MEQ density around the injection well) compares well with observed seismicity. The modeling indicates that the MEQ events are related to shear reactivation of preexisting fractures, which is triggered by the combined effects of injection-induced cooling around the injection well and small changes in steam pressure as far as half a kilometer away from the injection well. Pressure-monitoring data at adjacent wells and satellite-based ground-surface deformation data were also used to validate and further calibrate reservoir-scale hydraulic and mechanical model properties. The pressure signature monitored from the start of the injection was particularly useful for a precise back-calculation of reservoir porosity. Ultimately, the first few months of reservoir pressure and surface deformation data were useful for estimating the reservoir-rock permeability and elastic modulus. Finally, although the extent of the calculated stimulation zone matches the field observations over the first few months of injection, the observed surface deformations and MEQ evolution showed more heterogeneous behavior as a result of more complex geology, including minor faults and fracture zones that are important for consideration in the analysis of energy production and the long-term evolution of the EGS system.

58 GEOSCIENCES↗

Investigation of Diesel combustion using multiple injection strategies for idling after cold start of passenger-car engines

A comprehensive investigation was carried out in order to better understand the combustion behaviour in a low compression ratio DI Diesel engine when multiple injection strategies are applied just after the engine cold starts in low temperature conditions (idling). More specifically, the aim of this study was twofold: on one hand, to understand the effect of the multiple injection strategies on the indicated mean effective pressure; on the other hand, to contribute to the understanding of combustion stability characterized by the coefficient of variation of indicated mean effective pressure. The first objective was fulfilled by analyzing the rate of heat release obtained by in-cylinder pressure diagnosis. The results showed that the timing of the pilot injection closest to the main injection was the most influential parameter based on the behaviour of the rate of heat release (regardless of the multiple injection strategy applied). For the second objective, the combustion stability was found to be correlated with the combustion centroid angle. The results showed a trend between them and the existence of a range of centroid angles where the combustion stability is strong enough. In addition, it was also evident that convenient split injection allows shifting the centroid to such a zone and improves combustion stability after start. (author)

33 ADVANCED PROPULSION SYSTEMS↗

Center for the Study of Plasma Microturbulence

We have discovered a possible "natural fueling" mechanism in tokamak fusion reactors using large scale gyrokinetic turbulence simulation. In the presence of a heat flux dominated tokamak plasma, cold ions naturally pinch radially inward. If cold DT fuel is introduced near the edge using shallow pellet injection, the cold fuel will pinch inward, at the expense of hot helium ash going radially outward. By adjusting the cold DT fuel concentration, the core DT density profiles can be maintained. We have also shown that cold source ions from edge recycling of cold neutrals are pinched radially inward. This mechanism may be important for fully understanding the edge pedestal buildup after an ELM crash. Work includes benchmarking the gyrokinetic turbulence codes in the electromagnetic regime. This includes cyclone base case parameters with an increasing plasma beta. The code comparisons include GEM, GYRO and GENE. There is good linear agreement between the codes using the Cyclone base case, but including electromagnetics and scanning the plasma beta. All the codes have difficulty achieving nonlinear saturation as the kinetic ballooning limit is approached. GEM does not saturate well when beta gets above about 1/2 of the ideal ballooning limit. We find that the lack of saturation is due to the long wavelength k{sub y} modes being nonlinearly pumped to high levels. If the fundamental k{sub y} mode is zeroed out, higher values of beta nonlinearly saturate well. Additionally, there have been studies to better understand CTEM nonlinear saturation and the importance of zonal flows. We have continued our investigation of trapped electron mode (TEM) turbulence. More recently, we have focused on the nonlinear saturation of TEM turbulence. An important feature of TEM is that in many parameter regimes, the zonal flow is unimportant. We find that when zonal flows are unimportant, zonal density is the dominant saturation mechanism. We developed a simple theory that agrees with the simulation and predicts zonal density generation and feedback stabilization of the most unstable mode even in the absence of zonal flow. We are using GEM to simulate NSTX discharges. We have also done verification and validation on DIII-D. Good agreement with GYRO and DIII-D flux levels were reported in the core region.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗