SEARCH · Search NASA

Results for “cold-flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

NASA NTRS1972

Internal performance of a 10 deg conical plug nozzle with a multispoke primary and translating external shroud

An experimental investigation was conducted in a nozzle static test facility to determine the performance characteristics of a cold-flow, 21.59-centimeter-diameter plug nozzle with a multispoke primary. Two multispoke primary nozzles, a 12-spoke and a 24-spoke, were tested and compared with an annular plug nozzle. The supersonic cruise configurations for both spoke primaries performed about the same, with a gross thrust coefficient of 0.974, a decrease of approximately 1.5 percent from the reference nozzle. The takeoff configuration for the 12-spoke primary had a gross thrust coefficient of 0.957, a decrease of 1.5 percent from the reference nozzle, and the 24-spoke primary had a gross thrust coefficient of 0.95.

Bresnahan, D. L.↗

NASA NTRS1972

Development of a model and test equipment for cold flow tests at 500 atm of small nuclear light bulb configurations

A model and test equipment were developed and cold-flow-tested at greater than 500 atm in preparation for future high-pressure rf plasma experiments and in-reactor tests with small nuclear light bulb configurations. With minor exceptions, the model chamber is similar in design and dimensions to a proposed in-reactor geometry for tests with fissioning uranium plasmas in the nuclear furnace. The model and the equipment were designed for use with the UARL 1.2-MW rf induction heater in tests with rf plasmas at pressures up to 500 atm. A series of cold-flow tests of the model was then conducted at pressures up to about 510 atm. At 504 atm, the flow rates of argon and cooling water were 3.35 liter/sec (STP) and 26 gal/min, respectively. It was demonstrated that the model is capable of being operated for extended periods at the 500-atm pressure level and is, therefore, ready for use in initial high-pressure rf plasma experiments.

Jaminet, J. F.↗

NASA NTRS1972

Rocket Combustion Instability Suppression With Cavity Resonators

Properly tuned Helmholtz resonator damping devices are an effective method for eliminating high frequency combustion instability in rocket engine thrust chambers. A program was implemented with the objective of extending Helmholtz resonator theory to thrust chamber conditions to establish a standard design procedure. By using systematic cold-flow testing and hot firings, empirical design equations were formulated. An effort is currently underway to extend the design theory to other types of acoustical damping devices such as quarter-wave tubes and slots.

R H Counts↗

NASA NTRS1973

Externally blown flap dynamic loads

Some of the principal results obtained in three series of measurements of fluctuating surface pressures induced on externally blown flaps by jet impingment are presented. Large- and small-scale models and hot- and cold-flow tests are considered. The discussion sets forth scaling parameters and consistent features of the root-mean-square values and spectra of the loading. Implications of these results with regard to sonic fatigue are indicated.

Lansing, D. L.↗

NASA NTRS1972

Optimum design of space storable gas/liquid coaxial injectors.

Review of the results of a program of single-element, cold-flow/hot-fire experiments performed for the purpose of establishing design criteria for a high-performance gas/liquid (FLOX/CH4) coaxial injector. The approach and the techniques employed resulted in the direct design of an injector that met or exceeded the performance and chamber compatibility goals of the program without any need for the traditional 'cut-and-try' development methods.

Burick, R. J.↗

NASA NTRS1974

Effect of configuration variation on externally blown flap noise

The sensitivity of flap interaction noise to variations in engine-under-the-wing externally blown flap geometry was investigated with a large cold-flow model. Both 2- and 3-flap wing sections (7-ft chord) with trailing flap angles up to 60 deg were employed. Exhaust nozzles included coaxial, plug, and 8- and 13-inch diameter conical configurations. These nozzles were tested at two positions below the wing. The effects of these geometry variations on noise level, directivity, and spectral shape are summarized in terms of exhaust flow parameters evaluated at the nozzle exit and at the flap impingement station. The results are also compared with limited flap noise data available from tests using real engines.

Dorsch, R. G.↗

NASA NTRS1974

Rational function representation of flap noise spectra including correction for reflection effects

A rational function is presented for the acoustic spectra generated by deflection of engine exhaust jets for under-the-wing and over-the-wing versions of externally blown flaps. The functional representation is intended to provide a means for compact storage of data and for data analysis. The expressions are based on Fourier transform functions for the Strouhal normalized pressure spectral density, and on a correction for reflection effects based on the N-independent-source model of P. Thomas extended by use of a reflected ray transfer function. Curve fit comparisons are presented for blown flap data taken from turbofan engine tests and from large scale cold-flow model tests. Application of the rational function to scrubbing noise theory is also indicated.

Miles, J. H.↗

NASA NTRS1974

Externally blown flap noise research

The Lewis Research Center cold-flow model externally blown flap (EBF) noise research test program is summarized. Both engine under-the-wing and over-the-wing EBF wing section configurations were studied. Ten large scale and nineteen small scale EBF models were tested. A limited number of forward airspeed effect and flap noise suppression tests were also run. The key results and conclusions drawn from the flap noise tests are summarized and discussed.

Dorsch, R. G.↗

NASA NTRS1974

Noncircular Orifice Holes and Advanced Fabrication Techniques for Liquid Rocket Injectors (Phases 1, 2, 3, and 4)

A comprehensive summary of the results of a cold-flow and hot-fire experimental study of the mixing and atomization characteristics of injector elements incorporating noncircular orifices is presented. Both liquid/liquid and gas/liquid element types are discussed. Unlike doublet and triplet elements (circular orifices only) were investigated for the liquid/liquid case while concentric tube elements were investigated for the gas/liquid case. It is concluded that noncircular shape can be employed to significant advantage in injector design for liquid rocket engines.

Mchale, R. M.↗

NASA NTRS1974

Effect of configuration variation on externally blown flap noise

The sensitivity of flap interaction noise to variations in engine-under-the-wing externally blown flap geometry was investigated with a large cold-flow model. Both two- and three-flap wing sections (7-ft chord) with trailing flap angles up to 60 deg were employed. Exhaust nozzles included coaxial, plug, and 8- and 13-in.-diam conical configurations. These nozzles were tested at two positions below the wing (19-1/4 and 29-1/4 in.). The effects of these geometry variations on noise level, directivity, and spectral shape are summarized in terms of exhaust flow parameters evaluated at the nozzle exit and at the flap impingement station. The results are also compared with limited flap noise data available from tests using real engines.

Dorsch, R. G.↗

NASA NTRS1974

Acoustic characteristics of externally blown flap systems with mixer nozzles

Noise tests were conducted on a large-scale cold-flow model of an engine-under-the-wing externally blown flap lift augmentation system employing a mixer nozzle. The mixer nozzle was used to reduce the flap impingement velocity and, consequently, to try to attenuate the additional noise caused by the interaction between the jet exhaust and the wing flap. Results from the mixer nozzle tests are summarized and compared with the results for a conical nozzle. The comparison showed that, with the mixer nozzle, less noise was generated when the trailing flap was in a typical landing setting (e.g., 60 deg). However, for a takeoff flap setting (20 deg), there was little or no difference in the acoustic characteristics when either the mixer or conical nozzle was used.

Goodykoontz, J. H.↗

NASA NTRS1974

Rational functional representation of flap noise spectra including correction for reflection effects

A rational function is presented for the acoustic spectra generated by deflection of engine exhaust jets for under-the-wing and over-the-wing versions of externally blown flaps. The functional representation is intended to provide a means for compact storage of data and for data analysis. The expressions are based on Fourier transform functions for the Strouhal normalized pressure spectral density, and on a correction for reflection effects based on Thomas' (1969) N-independent-source model extended by use of a reflected ray transfer function. Curve fit comparisons are presented for blown-flap data taken from turbofan engine tests and from large-scale cold-flow model tests. Application of the rational function to scrubbing noise theory is also indicated.

Miles, J. H.↗

NASA NTRS1974

Externally blown flap noise research

Dorsch, R. G.↗

NASA NTRS1974

Noise of model target type thrust reversers for engine-over-the-wing applications

The results of experiments on the noise generated by V-gutter and semicylindrical target reversers with circular and short-aspect-ratio slot nozzles having diameters of about 5 cm are presented. The experiments were conducted with cold-flow jets at velocities from 190-290 m/sec. The reversers at subsonic jet velocities had a more uniform noise distribution and higher frequency than the nozzles alone. The reverser shape was shown to be more important than the nozzle shape in determining the noise characteristics. The maximum sideline pressure level varied with the sixth power of the jet velocity, and the data were correlated for angles along the sideline. An estimate of the noise level along the 152 m sideline for an engine-over-the-wing powered-lift airplane was made.

Stone, J. R.↗

NASA NTRS1975

The effect of turbulence on pollutant formation in a tubular burner

The role of turbulence in pollutant formation was investigated both experimentally and analytically with the objective of understanding the important mechanisms of a fairly basic level. Preliminary measurements of the cold-flow turbulence characteristics downstream of three perforated plate flame holders, of varying solidity ratio, were made. In the combustion experiment, measurements of the concentration distributions of CO, NO(x), HC, and CO2, downstream of the same flame holders, were made. The combustor configuration was tubular and constant-area, and the fuel was premixed, prevaporized propane. The experimental results were modeled by a one-dimensional analysis in which transport phenomena were neglected, and more successfully, by a quasi-one-dimensional analysis containing recirculation zones and turbulent transport effects.

Robinson, G. F.↗

NASA NTRS1957

Comparison of experimental with theoretical total-pressure loss in parallel-walled turbojet combustors

An experimental investigation of combustor total-pressure loss was undertaken to confirm previous theoretical analyses of effects of geometric and flow variables and of heat addition. The results indicate that a reasonable estimate of cold-flow total-pressure-loss coefficient may be obtained from the theoretical analyses. Calculated total-pressure loss due to heat addition agreed with experimental data only when there was no flame ejection from the liner at the upstream air-entry holes.

Dittrich, Ralph T↗

NASA NTRS1956

A Theory for Stability and Buzz Pulsation Amplitude in Ram Jets and an Experimental Investigation Including Scale Effects

From a theory developed on a quasi-one-dimensional-flow basis, it is found that the stability of the ram jet is dependent upon the instantaneous values of mass flow and total pressure recovery of the supersonic diffuser and immediate neighboring subsonic diffuser. Conditions for stable and unstable flow are presented. The theory developed in the report is in agreement with the experimental data of NACA-TN-3506 and NACA-RM-L50K30. A simple theory for predicting the approximate amplitude of small pressure pulsation in terms of mass-flow decrement from minimum-stable mass flow is developed and found to agree with experiments. Cold-flow tests at a Mach number of 1.94 of ram-jet models having scale factors of 3.15:1 and Reynolds number ratios of 4.75:1 with several supersonic diffuser configurations showed only small variations in performance between geometrically similar models. The predominant variation in steady-flow performance resulted from the larger boundary layer in the combustion chamber of the low Reynolds number models. The conditions at which buzz originated were nearly the same for the same supersonic diffuser (cowling-position angle) configurations in both large and small diameter models. There was no appreciable variation in stability limits of any of the models when the combustion-chamber length was increased by a factor of three. The unsteady-flow performance and wave patterns were also similar when considered on a reduced-frequency basis determined from the relative lengths of the model. The negligible effect of Reynolds number on stability of the off-design configurations was not anticipated in view of the importance of boundary layer to stability, and this result should not be construed to be generally applicable. (author)

Trimpi, Robert L↗

NASA NTRS1966

The Properties of Flowing Sheets Formed by Impingement of Liquid Jets on Curved Surfaces

An applied research program was conducted to determine the properties of flat sheets of propellants formed by directing jets of liquid tangentially against concave, cylindrical deflector surfaces. The dimensions and spatial orientation of the resultant sheets were found to depend only on the orifice diameter and deflector geometry for three propellant simulants of widely-varying physical properties, over the range of injection velocities encountered in liquid rocket engines. Correlating equations, suitable for use in injector design, are presented for free-sheet width and spreading angle. Distribution of mass and velocity across the free-flowing sheets is also reported. Conditions were discovered under which true sheets do not form, or at best malformed or pulsating sheets result. An envelope of geometrical constraints for deflector design is tentatively defined in order to avoid these undesirable operating regions. The results of the present cold-flow tests are compared with firing test data for impinging-sheet injectors and combustion performance is related to single sheet behavior.

Riebling, Robert W.↗