Search NASA⌕ Search

SEARCH · Search NASA

Results for “cycling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Excellent cycling stability of sodium anode enabled by a stable solid electrolyte interphase formed in ether-based electrolytes

Sodium (Na)-ion batteries have been considered as one of the most promising power sources beyond Li-ion batteries. Although Na metal anode exhibits a high theoretical capacity of 1165 mAh g-1, its application on Na batteries is largely hindered by dendrite growth and low Coulombic efficiency. Herein, we demonstrate that an electrolyte consists of 1 M sodium tetrafluoroborate in Tetraglyme can enable excellent cycling efficiency (99.9 %) of Na metal anode for more than 1000 cycles. This high reversibility of Na anode can be attributed to a stable solid electrolyte interphase formed on Na surface as revealed by cryogenic transmission electron microscopy and X-ray photoelectron spectroscopy. These electrolytes also enabled excellent cycling stability of Na||hard carbon cells and Na||Na2/3Co1/3Mn2/3O2 cells at high rate with very high coulombic efficiencies.

sodium metal, TEGDME, solid electrolyte interphase↗
DOE OSTI2025

Time-resolved targeted metabolomics shows an abrupt switch from Calvin-Benson-Bassham cycle to tricarboxylic acid cycle when the light is turned off

Abstract In leaves, major CO₂ fluxes alternate between fixation by the Calvin-Benson-Bassham (CBB) cycle during light and release by the tricarboxylic acid (TCA) cycle in darkness. The speed at which leaf metabolism transitions between these pathways likely influences plant tolerance to fluctuating light conditions. To investigate these rapid metabolic shifts, we exposed leaves to ¹³CO₂ for 20 min to establish a quasi-steady state before abruptly turning off the light while maintaining ¹³CO₂ feeding. Within 10 s of dark transition, 3-phosphoglycerate levels rose significantly while most other CBB cycle intermediates decreased by more than 90%. Simultaneously, carbon accumulated in alanine, likely via pyruvate. Over the subsequent 10 min, six- and five-carbon TCA cycle intermediates steadily increased. In contrast, four-carbon TCA intermediates peaked at one minute, declined at three minutes, and rose again at 10 min, a pattern mirrored by most measured amino acids. These results reveal an exceptionally rapid metabolic reconfiguration from CO₂ fixation by the CBB cycle in light to TCA cycle activation for energy production in darkness, accompanied by substantial changes in amino acid metabolism.

Plant Sciences↗
DOE OSTI2026

Data for Rewiring Yeast Metabolism for Producing 2,3-Butanediol and Two Downstream Applications: Techno-Economic Analysis and Life Cycle Assessment of Methyl Ethyl Ketone (MEK) and Agricultural Biostimulant Production

Rising concerns for sustainability and global climate change have driven the development of sustainable production pathways for biofuels and chemicals from lignocellulosic biomass via integrated biological and chemical processes. We constructed an engineered Saccharomyces cerevisiae capable of producing 2,3-butanediol (2,3-BDO) from glucose without accumulating ethanol and glycerol, which hinder downstream processing of 2,3-BDO, through extensive metabolic reprogramming. Specifically, we introduced heterologous 2,3-BDO biosynthetic enzymes and deleted the major isozymes of ethanol and glycerol biosynthetic enzymes. In addition, we introduced an NAD+ regenerating Pyruvate-Malate (PM) cycle and enhanced the NAD+ regenerating capability of the PM cycle to resolve the redox imbalance from the deletion of ethanol and glycerol production pathways. The resulting engineered yeast produced 109.9 g/L of 2,3-BDO with a productivity of 1.0 g/L/h and a yield of 0.36 g/g glucose in a fed-batch fermentation. We also conducted techno-economic analysis (TEA) and life cycle assessment (LCA) of the production of methyl ethyl ketone (MEK) through catalytic dehydration of 2,3-BDO. A TEA based on the experimental results indicated that the minimum product selling price (MPSP) was estimated to be $1.90/kg. Regarding cradle-to-grave LCA, 100-year global warming potential (GWP100) and fossil energy consumption (FEC) were found to be 0.37 kg CO2 eq/kg and 3.1 MJ/kg, respectively. These results demonstrated the feasibility of cost-competitive and sustainable bio-based MEK production via yeast fermentation. In addition, we explored the possibility of using the fermentation broth containing 2,3-BDO as a biostimulant inducing drought tolerance in plants. As a result, the yeast 2,3-BDO fermentation broth can induce drought tolerance in Arabidopsis thaliana without a complicated purification process.

Economics↗
DOE OSTI2020

Large-eddy simulation study on cycle-to-cycle variation of knocking combustion in a spark-ignition engine

The cycle-to-cycle variation in the knock intensity is commonly encountered under abnormal combustion conditions. The severity of these abnormal combustion events can vary significantly, and the efficiency of engines at high loads is limited in practice by heavy knocking phenomena. Since, a thorough analysis of such recurrent but non-cyclic phenomena via experiments alone becomes highly cumbersome, in the present work, a multi-cycle large-eddy simulation study was performed to quantitatively predict cyclic variability in the combustion process and cyclic knock intensity variability in a direct injection spark-ignition engine. To account for the turbulence-chemistry interaction effects on flame propagation, the G-equation combustion model was used. Detailed chemistry was solved outside the flame front with a toluene primary reference fuel skeletal kinetic mechanism. For both the mild knock and heavy knock conditions, the numerical results were validated against experimental measurements. Based on the simulation results, a correlation analysis was performed considering combustion phasing, peak cylinder pressure and maximum amplitude of pressure oscillation. Furthermore, a detailed three-dimensional spatial analysis illustrated the evolution of auto-ignition kernel development and propagation of pressure waves during knocking combustion for three typical cycles with different knock intensities. In this process, it was found that an early occurrence of auto-ignition in the end gas was prone to high knock intensity. Although multiple auto-ignition kernels were observed in different cycles, the degree of coupling between chemical heat release and pressure waves varied, thereby leading to different maximum amplitude of pressure oscillation values.

42 ENGINEERING↗
DOE OSTI2024

The importance of cycle-by-cycle data in performing rapid battery technology development and validation

Lithium-ion battery (LiB) technology is playing a crucial role in transforming the predominantly fossil fuel-based transportation and stationary storage sectors to achieve a low-carbon economy. Rapid innovation in the LiB materials to electrode to cell design is happening to satisfy the performance, life, and safety metrics required by those myriads of applications. Lately, advanced analytics, such as machine-learning or artificial intelligence (ML/AI) techniques, are being used more frequently to aid in expedited LiB technology development, performance validation, and life prediction. The success of these techniques often relies on a large volume of well-defined and high-quality battery test data. On the other hand, most battery developers and research and development (R&D) communities are still following a classical approach to develop batteries, which is running calendar- and/or cycle-aging tests, performing reference performance tests (RPTs), and conducting post-mortem analyses periodically without paying attention to the wealth of data often not collected during the calendar or cycle life aging tests. This sparse data collection approach is time- and resource-intensive, requiring data capture and evaluation of months to years of RPT data to diagnose accurate battery state of performance, health, and safety. Even so, the underlying aging modes and mechanisms can be missed. If collected properly, battery test data during cycling or calendaring can be efficiently combined with ML/AI techniques to create powerful tools in the rapid diagnosis of battery state of performance, health, and safety along with insights into underlying aging modes and mechanisms. In this report, we discuss the importance of effective cycle-by-cycle (CBC) data collection with example case studies. Within a reasonable timeframe, RPT data are often inadequate in capturing many of the crucial battery aging dynamics, which often predominantly show up in CBC test data. Finally, we also show examples of ML/AI techniques that use CBC data in rapid diagnosis and projection of LiB state of health (SOH) to motivate the scientific community in collecting and using CBC data to facilitate expeditious technology development and validation.

25 ENERGY STORAGE↗
DOE OSTI2020

Laminar-to-turbulent flame transition and cycle-to-cycle variations in large eddy simulation of spark-ignition engines

This paper investigates the effect of laminar-to-turbulent flame transition modeling on the prediction of cycle-to-cycle variations (CCVs) in large eddy simulation (LES) of spark-ignition (SI) engines. A laminar-to-turbulent flame transition model that describes the non-equilibrium sub-filter flame speed evolution during an early stage of flame kernel growth is developed. In the present model, the flame transition is characterized by the flame kernel size at which the flame transition ends, defined here as the flame transition scale. The proposed model captures the effects that variations in a turbulent flow field have on the evolution of early-stage burning rates, through variations in the flame transition scale. The proposed flame transition model is combined with the front propagation formulation (FPF) method and a spark-ignition model to predict CCVs in a gasoline direct injection SI engine. It is found that multi-cycle LES with the proposed flame transition model reproduces experimentally-observed CCVs satisfactorily. When the transition model is not considered or when variations in the transition process are neglected, CCVs are significantly under-predicted for the case considered here. These results indicate the importance of modeling the laminar-to-turbulent flame transition and the effect of turbulence on the transition process, when predicting CCVs, under certain engine conditions. The LES results are also used to analyze sources for variations in the flame transition. It is found, for the present engine case, that the most important source is the cycle-to-cycle variation in the turbulence dissipation rate, which is used to measure the strength of turbulence in the proposed model, near a spark plug. The large-scale velocity field and the variations of the laminar flame speed due to the mixture composition and thermal stratification are also found to be important factors to contribute to the variations in the flame transition.

42 ENGINEERING↗
DOE OSTI2021

Optical Cycling Functionalization of Arenes

Closed, laser-induced optical transitions (“optical cycling transitions”) of molecules can be used for state preparation and measurement in quantum information science and quantum sensing. Increasingly complex molecular species supporting optical cycling can provide new capabilities for quantum science, and it is not clear if there is a limit on their size or complexity. We explore Ca–O–L molecular constructs to support the optical cycling center, Ca, with ligands, L, being arenes. We find that L can be as large as coronene (i.e., CaOC 24 H 11 ) without losing the diagonality of the Franck–Condon factor (FCF). Furthermore, L can be substituted with electron-withdrawing groups to improve the FCF. Larger L, beyond ~7 rings, can disrupt the diagonality of the FCF by closing the HOMO–LUMO ligand electronic state gap and reordering with the local states on the cycling center. Altogether, we find that optical cycling can be retained for arenes, and we offer a principle for their design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

ORGANIC RANKINE CYCLE TURBINE AND HEAT EXCHANGER SIZING FOR LIQUID AIR COMBINED CYCLE

Cryogenic energy storage offers several opportunities to design turbomachinery and other equipment for novel cycles. This paper presents the design and analysis of turbomachinery and heat exchangers for an Organic Rankine Cycle (ORC) subsystem for a hybrid energy storage concept. The Liquid Air Combined Cycle is an energy storage system that stores air at cryogenic conditions at times with high variable renewable energy to be dispatched along with a gas turbine to recover the exhaust heat. In order to re-vaporize the air, the liquid air is coupled with an ORC as an additional bottoming cycle. The ORC turbine is expected to expand the fluid with a pressure ratio of nearly 30 and a flow rate of approximately 45 kg/s. Sizing calculations for both a radial and axial turbine solution were performed over a range of speeds and stages to determine the optimal design point. The results show that either an axial (8- or 9-stage) or radial (four stages at two shaft speeds) turbine are capable of handling the pressure ratios. Further trades of the two configurations would be required to determine the best option. The ORC system also incorporates five heat exchangers to distribute heat, vaporize the liquid air, or recover exhaust heat from the gas turbine. Three heat exchangers were analyzed to understand the size of heat exchangers and pressure drop for the overall system. Different types of heat exchangers were explored for the different purposes, including plate-fin heat exchangers, gasketed plate heat exchangers and shell-in-tube heat exchangers. It was determined that the ORC recuperator, liquid-air vaporizer, and vaporized air pre-heater would be counter-flow heat exchangers using a gasketed plate design. Keywords: Energy Storage, Liquid Air Energy Storage, Organic Rankine Cycle

Pryor, Owen↗
DOE OSTI2021

Water Cycle-Driven Infectious Diseases as Multiscale, Reliable, Continuously Updating Water Cycle Sensors

We propose a novel synthesis of observational and simulated data (climatological and biological) to enhance understanding of the real-world interplay between climate (here, the water cycle) and the epidemiology of water cycle-driven infectious disease. Aligning with Focal Area 2, predictive modeling using AI techniques, we will develop systems of hierarchical models to discover latent features of the water cycle. Our approach will leverage state-of-the-art in Artificial Intelligence (AI) to measure the degree to which climate change-driven shifts in water cycle can be predicted by supplementing sparse and irregular climate data with water cycle-driven infectious disease resources.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Off-Design Load Analysis of sCO2 Bottoming Cycle for a Natural Gas Combined Cycle Power Plant with Carbon Capture

As an alternative to a steam cycle, a supercritical carbon dioxide (sCO2) power cycle can be considered. Able et. al performed an analysis of an sCO2 cycle in a 2x2-1 configuration; however, this study did not include carbon capture. Previous studies assumed an H-Frame turbine and added a solvent based 95% carbon capture system and performed a levelized cost of electricity (LCOE) optimization for the plant. Their results suggest a LCOE slightly better than when using a steam cycle. In the study, steam is still generated in the heat recovery sections for the solvent regeneration in the carbon capture stripper reboiler. H-Frame gas turbines are also assumed. This work starts with the optimal design from the mentioned work to analyze the off-design performance of the power plant from 100% down to 50% load. The main operational findings and plant-efficiency for off-load conditions while maintaining the target CO2 capture rate are presented. H-Frame gas turbine off-design performance and exhaust conditions to the heat recovery section are obtained from commercial software, Thermoflow®. The CO2 turbomachinery, heat exchangers and other unit operations are sized and implemented in an Aspen Plus® model. Using the gas turbine exhaust conditions as input, the sCO2 cycle is optimized by adjusting stream split ratios, sCO2 circulation flowrate and compressor speed for maximum efficiency. This is done while keeping the target 95% CO2 capture.

Chinen, Anderson Soares↗
DOE OSTI2026

Drive Cycles, Battery Pack Scaling, and Usage Considerations for Long-Haul and Regional-Haul Electric Trucks

Electrifying Class-8 heavy-duty trucks presents a promising opportunity to enhance energy efficiency and reduce freight transport costs. Battery electric trucks (BETs), once considered niche, are gaining traction due to advancements in battery technology and cost reductions. However, accurately predicting battery lifespan under realistic usage conditions remains a key challenge. Understanding battery failure mechanisms and their links to design, operation, and management is essential for developers and fleet operators. This study introduces a method to develop simplified, lab-testable dynamic stress test (DST) cycles for regional and long-haul Class-8 BETs, derived from real-world diesel truck usage. These DSTs enable benchmarking of battery technologies, identification of aging stressors, and optimization of battery design, life, and cost. The approach supports evaluation of key metrics such as levelized cost of driving and total cost of ownership, aiding fair comparisons and adoption decisions. We also propose feasible battery pack sizes that meet current driving demands with strategic charging, and a method to scale pack-level DSTs to cell-level cycles for lab-based testing. These tools facilitate tradeoff analysis across battery chemistries, pack sizing, and charging strategies, while offering means to get insights into battery aging under realistic conditions-ultimately supporting informed BET deployment decisions.

25 ENERGY STORAGE↗
DOE OSTI2023

Impact of Detailed Parameter Modeling of Open-Cycle Gas Turbines on Production Cost Simulation: Preprint

Flexible resources are increasingly important as variable renewable energy deployment in the power system increases. Although many systems are transitioning away from fossil fuels, open-cycle gas turbines are likely to play an important balancing role for some time, thus requiring accurate modeling of their operational parameters. This paper explores the impact of detailed representation of three operational parameters - start- up costs, run-up rates, and forced outage rates - in the production cost model of a system as it adopts higher levels of wind and solar. Using PLEXOS simulations of the NREL-118 bus test system, the study examines how more detailed parameter modeling affects outcomes such as the number of start-ups and shutdowns, ramping and total generation costs for open-cycle gas turbines, as renewable energy levels increase. The results suggest the value of detailed parameter modeling and continued research on combustion turbines' ability to provide flexibility.

economic dispatch↗
DOE OSTI2020

Learning reference governor for cycle-to-cycle combustion control with misfire avoidance in spark-ignition engines at high exhaust gas recirculation–diluted conditions

Cycle-to-cycle feedback control is employed to achieve optimal combustion phasing while maintaining high levels of exhaust gas recirculation by adjusting the spark advance and the exhaust gas recirculation valve position. The control development is based on a control-oriented model that captures the effects of throttle position, exhaust gas recirculation valve position, and spark timing on the combustion phasing. Under the assumption that in-cylinder pressure information is available, an adaptive extended Kalman filter approach is used to estimate the exhaust gas recirculation rate into the intake manifold based on combustion phasing measurements. The estimation algorithm is adaptive since the cycle-to-cycle combustion variability (output covariance) is not known a priori and changes with operating conditions. A linear quadratic regulator controller is designed to maintain optimal combustion phasing while maximizing exhaust gas recirculation levels during load transients coming from throttle tip-in and tip-out commands from the driver. During throttle tip-outs, however, a combination of a high exhaust gas recirculation rate and an overly advanced spark, product of the dynamic response of the system, generates a sequence of misfire events. In this work, an explicit reference governor is used as an add-on scheme to the closed-loop system in order to avoid the violation of the misfire limit. The reference governor is enhanced with model-free learning which enables it to avoid misfires after a learning phase. Experimental results are reported which illustrate the potential of the proposed control strategy for achieving an optimal combustion process during highly diluted conditions for improving fuel efficiency.

42 ENGINEERING↗
DOE OSTI2020

Task 12 PV Sustainability - Life Cycle Inventories and Life Cycle Assessments of Photovoltaic Systems

Life Cycle Assessment (LCA) is a structured, comprehensive method of quantifying material- and energy-flows and their associated impacts in the life cycles of products (i.e., goods and services). One of the major goals of IEA PVPS Task 12 is to provide guidance on assuring consistency, balance, transparency and quality of LCA to enhance the credibility and reliability of the results. The current report presents the latest consensus life cycle inventories among the authors, PV LCA experts in North America, Europe, Asia and Australia. At this time consensus is limited to four technologies for which there are well-established and up-to-date life cycle inventory (LCI) data (mono- and multi-crystalline Si, CdTe, CIGS, as well as one emerging technology (perovskite silicon tandem). LCIs are necessary for LCA and the availability of such data is often the greatest barrier for conducting LCA. The Task 12 LCA experts have put great efforts in gathering and compiling the LCI data presented in this report. These include detailed inputs and outputs during manufacturing of cell, wafer, module, and balance-of-system (i.e., structural and electrical components) that were estimated from actual production and operation facilities. In addition, data are presented to enable analyses of various types of PV installations; these include operational data of rooftop and ground-mount PV systems and country-specific PV-mixes. The LCI datasets presented in this report are the latest that are available to the public describing the status in 2018 for crystalline Si (some manufacturing data from 2011 were not updated), 2015 and 2017-2018 for CdTe, 2010 for CIGS, 2010 for HCPV, and 2017 for perovskite silicon tandem technology.

14 SOLAR ENERGY↗
DOE OSTI2022

Design optimization of an additively manufactured prototype recuperator for supercritical CO 2 power cycles

Supercritical CO 2 (sCO 2 ) power cycles are being developed due to their potential for high efficiency and reduced capital cost. It is necessary that these recuperators operate at high pressures and temperatures, up to 30 MPa and 900 K, with effectiveness values > 95% and pressure drops <1% to achieve high cycle efficiencies. Moreover, it is also necessary to have reasonable cost recuperators to control the capital costs of the sCO 2 power cycles. In this study, a Plate Pin-Fin (PPF) heat exchanger has been proposed as an sCO 2 recuperator. This preliminary recuperator design leverages capabilities enabled by additive manufacturing. Although the PPF design has characteristics similar to those of a plate heat exchanger, small diameter and relatively long fins are used to increase surface area, enhance heat transfer, and provide structural support for the partition plates that separate the fluid streams. Existing correlations for heat transfer and pressure drop were adapted for the PPF heat exchanger. These correlations were implemented in a 1D analytical model and used for the optimization of a 5-kW th high temperature recuperator for an indirect sCO 2 cycle by varying the design parameters to minimize the quantity of material required. A 3D conjugate heat transfer numerical simulations were conducted to validate the heat transfer and pressure loss correlations. A steepest descent method was used to minimize heat exchanger mass for a 5-kW prototype recuperator subject to a maximum specified pressure drop. Additionally, the design analysis indicated that an optimum PPF recuperator would be attained for the minimum allowable pin transverse spacing, minimum pin width, minimum pin height and near maximum cell aspect ratio. Moreover, at a low material requirement of 0.216 kg/kW and a pressure drop, which is almost five times lower than the allowable pressure drop design target, the optimized PPF heat exchanger has the high potential to be an alternative to a printed circuit heat exchanger, which is a conservative design basis for the current state-of-the-art sCO 2 recuperators.

42 ENGINEERING↗
DOE OSTI2022

A cycle-jump acceleration method for the crystal plasticity simulation of high cycle fatigue of the metallic microstructure

For metallic materials, high-cycle fatigue life is sensitive to underlying microstructure features including secondary phases, textures, grains morphology, etc. The traditional, data-based safe-life approaches for modeling fatigue don’t explicitly consider the microstructure and can’t guide study in microstructure modification for improved fatigue property. Crystal plasticity-based simulation provides increased model fidelity at the expense of immense computation time, making it inapplicable for high cycle fatigue. In this work, an acceleration method based on cycle-jump approach (Lesne and Savalle, 1989) was developed for microstructure-based high-cycle FE simulation using crystal plasticity constitutive-model. We report this method demonstrated high efficiency in benchmark tests of various conditions.

36 MATERIALS SCIENCE↗