Search NASA⌕ Search

SEARCH · Search NASA

Results for “deformation and fracture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Deformation and fracture behavior of Ni-Mo-Al(gamma/gamma prime-alpha) in situ composite

Tensile properties of a directionally solidified (DS) eutectic alloy of the nominal composition Ni-33 Mo-5.7 Al (weight percent) have been investigated both at room temperature and elevated temperatures. The microstructure-mechanical property relationship has been studied for the alloy both in the as-DS and heat-treated conditions. Changes in the yield strength, the work hardening behavior, and the fracture morphology have been explained in terms of the microstructural changes due to the heat treatment. The yield drops observed have been attributed to the microdebonding due to the possible segregation of impurities at the fiber-matrix interface, and partly to the strain aging. The deformation mechanism has been identified to be the cutting of gamma prime particles.

Sriramamurthy, A. M.↗
NASA NTRS1990

The effect of hydrogen on the deformation and fracture behavior of a single crystal nickel-base superalloy

The room temperature and 300 C tensile behavior of a single crystal superalloy, PWA 1480, has been studied as a function of internal hydrogen concentration and microstructure. Hydrogen is trapped at the porosity and eutectic gamma/gamma in the microstructure, and the effect of these trapping sites on the tensile behavior will be discussed. There is no effect of hydrogen on strength, however, the strain to failure decreases steadily with increasing hydrogen content up to 200 ppm. Cleavage of the eutectic gamma/gamma occurs without hydrogen, but the presence of internal hydrogen causes cracking in the eutectic gamma/gamma at a much earlier stage of deformation leading to a small total strain. In contrast to many superalloys with a high volume fraction of gamma precipitates, there was no evidence of shearing of the gamma, and it was found that at all strains the dislocations are trapped in the gamma matrix. The effect of hydrogen on this behavior and its relation to fracture is described.

Walston, W. S.↗
NASA NTRS1973

Solute effects on deformation and fracture of beta brass

It is shown that the ductility of several ternary beta brass alloys in air and in several liquid metals can be related to the operative slip and grain boundary relaxation processes. Nickel and manganese were chosen as alloying elements because they are expected to respectively enhance and suppress cross slip in beta brass. Single-phase binary and ternary beta brass alloys were used in both polycrystalline and single crystal form.

Shea, M. M.↗
NASA NTRS1982

Mechanisms of deformation and fracture in high temperature low cycle fatigue of Rene 80 and IN 100

Specimens tested for the AGARD strain range partitioning program were investigated. Rene 80 and IN 100 were tested in air and in vacuum; at 871 C, 925 C, and 1000 C; and in the coated and uncoated condition. The specimens exhibited a multiplicity of high-temperature low-cycle fatigue damage. Observations of the various forms of damage were consistent with material and testing conditions and were generally in agreement with previous studies. In every case observations support a contention that failure occurs at a particular combination of crack length and maximum stress. A failure criterion which is applicable in the regime of testing studied is presented. The predictive capabilities of this criterion are straight forward.

Romanoski, G. R., Jr.↗
NASA NTRS1988

The effect of hydrogen on the deformation and fracture of PWA 1480

The effect of internal hydrogen on mechanical properties and fracture behavior is studied in the single-crystal nickel-base superalloy PWA 1480. In particular, plane strain fracture toughness and tensile tests have been performed in hydrogen-free samples and hydrogen-gas phase-charged samples in two different sample orientations. The mechanical properties, as well as the fracture process, were found to be very dependent on orientation. Hydrogen did not affect the yield strength but reduced the uniform tensile elongation more than 75 percent. However, hydrogen reduced the tensile reduction-in-area and the fracture toughness by only 10 percent. Cleavage of the eutectic gamma-prime, as well as the role of hydrogen trapping, will be discussed. These results will be analyzed in terms of the effects that orientation, microstructure, and hydrogen have on the fracture process.

Walston, W. S.↗
NASA NTRS1990

Deformation and fracture of aluminum-lithium alloys: The effect of dissolved hydrogen

The effects of dissolved hydrogen on the mechanical properties of 2090 and 2219 alloys are studied. The work done during this semi-annual period consists of the hydrogen charging study and some preliminary mechanical tests. Prior to SIMS analysis, several potentiostatic and galvanostatic experiments were performed for various times (going from 10 minutes to several hours) in the cathodic zone, and for the two aqueous solutions: 0.04N of HCl and 0.1N NaOH both combined with a small amount of As2O3. A study of the surface damage was conducted in parallel with the charging experiments. Those tests were performed to choose the best charging conditions without surface damage. Disk rupture tests and tensile tests are part of the study designed to investigate the effect of temperature, surface roughness, strain rate, and environment on the fracture behavior. The importance of the roughness and environment were shown using the disk rupture test as well as the importance of the strain rate under hydrogen environment. The tensile tests, without hydrogen effects, have not shown significant differences between low and room temperature.

Rivet, F. C.↗
NASA NTRS1991

Mechanical characterization and modeling of non-linear deformation and fracture of a fiber reinforced metal matrix composite

The nonlinear anisotropic mechanical behavior of an aluminum alloy metal matrix composite reinforced with continuous alumina fibers was determined experimentally. The mechanical behavior of the composite were modeled by assuming that the composite has a periodical microstructure. The resulting unit cell problem was solved with the finite element method. Excellent agreement was found between theoretically predicted and measured stress-strain responses for various tensile and shear loadings. The stress-strain responses for transverse and inplane shear were found to be identical and this will provide a simplification of the constitutive equations for the composite. The composite has a very low ductility in transverse tension and a limited ductility in transverse shear that was correlated to high hydrostatic stresses that develop in the matrix. The shape of the initial yield surface was calculated and good agreement was found between the calculated shape and the experimentally determined shape.

Jansson, S.↗
NASA NTRS1991

Temperature effects on the deformation and fracture of Al-Li-Cu-In alloys

The crack initiation and growth fracture resistance of Al-Cu-Li and Al-Cu-Li-In alloys were characterized and optimized for cryogenic tank applications. Presently, the effects of stress state and temperature is being determined on the fracture toughness and fracture mechanisms of commercially available Vintage 3 2090-T81 and experimental 2090+In-T6. Precracked J-integral specimens of both alloys were tested at ambient and cryogenic temperatures in the plane stress and plane strain conditions. Considering ambient temperature, results showed that 2090-T81 exhibited the highest toughness in both plane strain and plane stress conditions. For the plane strain condition, reasonable crack initiation and growth toughness of 1090-T81 are associated with a significant amount of delamination and transgranular fracture. Plane stress toughnesses were higher and fracture was characterized by shear cracking with minimal delaminations. In comparisons, the fracture behavior of 2090+In-T6 is significantly degraded by subgrain boundary precipitation. Toughness is low and characterized by intersubgranular fracture with no delamination in the plane stress or plane strain conditions. Intersubgranular cracking is a low energy event which presumably occurs prior to the onset of slip band cracking. Copious grain boundary precipitation is atypical of commercially available 2090. At cryogenic temperatures, both alloys exhibit increased yield strength, toughness, and amount of delamination and shear cracking. The change in fracture mode of 2090+In-T6 from intersubgranular cracking at ambient temperature to a combination of intersubgranular cracking, shear cracking, and delamination at cryogenic temperature is the subject of further investigation.

Wagner, John A.↗
NASA NTRS1992

The effect of temperature on the deformation and fracture of SiC/Ti-24Al-11Nb

The effect of temperature on the stress-strain behavior in air and the failure mechanisms of Ti-24Al-11Nb alloy and of a SiC/Ti-24Al-11Nb composite with continuous SiC fibers oriented parallel to the loading direction was investigated over temperature range 23-815 C. It was found that the tensile failure process of SiC/Ti-24Al-11Nb was controlled at all temperatures by fiber fracture. Composite failure occurred at 0.8 percent strain at all temperatures. Debond and frictional stresses at the fiber-matrix interface decreased with increased temperature.

Brindley, P. K.↗
NASA NTRS1987

Effect of heat treatment on the fracture behaviour of directionally solidified (gamma/gamma-prime)-alpha alloy

An investigation is conducted into the influence of various heat treatments on the work of fracture and its relation to microstructure for a directionally solidified Ni-33Mo-5.7Al (wt pct) (gamma/gamma-prime)-alpha alloy. The jagged crack propagation observed is due to delamination of the ligaments and associated plastic deformation. Fracture behavior is examined with respect to alloy microstructures and load-deflection curves. The four heat-treatment conditions considered are: (1) as-directionally solidified, (2) solutionized, (3) directionally solidified and thermally cycled, and (4) solutionized and thermally cycled.

Sriramamurthy, A. M.↗
NASA NTRS2002

Multiscale Modeling, Simulation and Visualization and Their Potential for Future Aerospace Systems

This document contains the proceedings of the Training Workshop on Multiscale Modeling, Simulation and Visualization and Their Potential for Future Aerospace Systems held at NASA Langley Research Center, Hampton, Virginia, March 5 - 6, 2002. The workshop was jointly sponsored by Old Dominion University's Center for Advanced Engineering Environments and NASA. Workshop attendees were from NASA, other government agencies, industry, and universities. The objectives of the workshop were to give overviews of the diverse activities in hierarchical approach to material modeling from continuum to atomistics; applications of multiscale modeling to advanced and improved material synthesis; defects, dislocations, and material deformation; fracture and friction; thin-film growth; characterization at nano and micro scales; and, verification and validation of numerical simulations, and to identify their potential for future aerospace systems.

Noor, Ahmed K.↗
NASA NTRS2003

Visible/Near-Infrared Spectra of Experimentally Shocked Plagioclase Feldspars

Minerals subjected to high shock pressures exhibit structural changes with increasing pressure (e.g., fractures, deformations, formation of diaplectic glass, and complete melting [1-6]). Petrologic and thermal infrared spectroscopic studies have shown that diaplectic glass (maskelynite) formation in feldspars occurs between ~25-45 GPa, while significant melting occurs above ~45 GPa [7- 12]. Past studies of visible/near-infrared spectra of shocked plagioclase feldspars demonstrated few variations in spectral features with pressure except for a decrease in the absorption feature near 1250 nm and an overall decrease in albedo [13-17]. We report new visible/near-infrared spectra of albite- and anorthiterich rocks experimentally shocked from 17-56 GPa.

Johnson, J. R.↗
NASA NTRS2019

Hydrogen Isotope Fractionation During Impact Degassing of Pyroxene and Maskelynite in Shergottite Larkman Nunatak 06319

Hydrogen in nominally anhydrous minerals (NAMs) in meteorites provides insight to mantle sources of indigenous water on differentiated bodies: e.g. Peslier et al. 2017 [1], including Mars [2-4]. However, all meteorite samples, including Martian shergottites, record impact events as fractures, deformation, silicate darkening, shock melt veins and pockets, etc. The effect of shock on hydrogen in NAMs is poorly constrained, and must be understood prior to using these data to infer planetary indigenous water. Here we present water contents and D/H ratios (calculated as dD, i.e. the variation of the D/H ratio relative to a standard, in this case sea water "SMOW") in pyroxene, olivine and maskelynite in the olivine-phyric shergottite Larkman Nunatak 06319 (LAR 06319) as a function of proximity to impact melt. While the results suggest impact may have a role in fractionating H isotopes, the magmatic signature of H2O in Mars can be preserved in some pyroxene.

Dudley, J. M.↗
NASA NTRS1987

Deformation, fatigue and fracture behavior of two cast anisotropic superalloys

Tensile and low cycle fatigue (LCF) tests were conducted on two cast anisotropic superalloys. The effects of temperature, strain rate and stress range were investigated. Deformation behavior was extensively characterized and modeled. LCF and fracture behavior were studied and correlated with deformation behavior.

Milligan, Walter W.↗
NASA NTRS1966

Earth's zonal deformations.

Flows and fractures as types of deformation occurring on Earth under huge loads of ice suggested by isostatic compensation of Antarctica, Arctic basin and glaciated region in North America

ARCTIC↗
NASA NTRS1972

Deformation, recrystallization, strength, and fracture of press-forged ceramic crystals.

Sapphire and ruby were very difficult to press-forge because they deformed without cracking only in a limited temperature range before they melted. Spinel crystals were somewhat easier and MgO, CaO, and TiC crystals much easier to forge. The degree of recrystallization that occurred during forging (which was related to the ease and type of slip intersections) varied from essentially zero in Al2O3 to complete (i.e., random polycrystalline bodies were produced) in CaO. Forging of bi- and polycrystalline bodies produced incoherent bodies as a result of grain-boundary sliding. Strengths of the forged crystals were comparable to those of dense polycrystalline bodies of similar grain size. However, forged and recrystallized CaO crystals were ductile at lower temperatures than dense hot-pressed CaO. This behavior is attributed to reduced grain-boundary impurities and porosity. Fracture origins could be located, indicating that fracture in the CaO occurs internally as a result of surface work hardening caused by machining.-

Rice, R. W.↗
NASA NTRS1995

NASA-UVA Light Aerospace Alloy and Structures Technology program (LA2ST)

The objective of the LA2ST Program is to conduct interdisciplinary graduate student research on the performance of next generation, light-weight aerospace alloys, composites, and thermal gradient structures in collaboration with NASA-Langley researchers. The general aim is to produce relevant data and basic understanding of material mechanical response, environment/corrosion behavior, and microstructure; new monolithic and composite alloys; advanced processing methods; new solid and fluid mechanics analyses; measurement and modeling advances; and a pool of educated students for aerospace technologies. Specific technical objectives are presented for each of the following research projects: time-temperature dependent fracture in advanced wrought ingot metallurgy, and spray deposited aluminum alloys; cryogenic temperature effects on the deformation and fracture of Al-Li-Cu-In alloys; effects of aging and temperature on the ductile fracture of AA2095 and AA2195; mechanisms of localized corrosion in alloys 2090 and 2095; hydrogen interactions in aluminum-lithium alloys 2090 and selected model alloys; mechanisms of deformation and fracture in high strength titanium alloys (effects of temperature and hydrogen and effects of temperature and microstructure); evaluations of wide-panel aluminum alloy extrusions; Al-Si-Ge alloy development; effects of texture and precipitates on mechanical property anisotropy of Al-Cu-Mg-X alloys; damage evolution in polymeric composites; and environmental effects in fatigue life prediction - modeling crack propagation in light aerospace alloys.

Starke, Edgar A., Jr.↗