SEARCH · Search NASA

Results for “detachment”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

NASA NTRS2009

Numerical Optimization of the Thermal Field in Bridgman Detached Growth

The global modeling of the thermal field in two vertical Bridgman-like crystal growth configurations, has been performed to get optimal thermal conditions for a successful detached growth of Ge and CdTe crystals. These computations are performed using the CrysMAS code and expand upon our previous analysis [1] that propose a new mechanism involving the thermal field and meniscus position to explain stable conditions for dewetted Bridgman growth. The analysis of the vertical Bridgman configuration with two heaters, used by Palosz et al. for the detached growth of Ge, shows, consistent with their results, that the large wetting angle of germanium on boron nitride surfaces was an important factor to promote a successful detached growth. Our computations predict that by initiating growth much higher into the hot zone of the furnace, the thermal conditions will be favorable for continued detachment even for systems that did not exhibit high contact angles. The computations performed for a vertical gradient freeze configuration with three heaters representative of that used for the detached growth of CdTe, show favorable thermal conditions for dewetting during the entirely growth run described. Improved thermal conditions are also predicted for coated silica crucibles when the solid-liquid interface advances higher into the hot zone during the solidification process. The second set of experiments on CdTe growth described elsewhere has shown the reattachment of the crystal to the crucible after few centimeters of dewetted growth. The thermal modeling of this configuration shows a second solidification front appearing at the top of the sample and approaching the middle line across the third heater. In these conditions, the crystal grows detached from the bottom, but will be attached to the crucible in the upper part because of the solidification without gap in this region. The solidification with two interfaces can be avoided when the top of the sample is positioned below the middle position of the third furnace.

Stelian, C.↗

NASA NTRS2016

Detached Solidification of Germanium-Silicon Crystals on the ISS

A series of Ge(sub 1-x) Si(sub x) crystal growth experiments are planned to be conducted in the Low Gradient Furnace (LGF) onboard the International Space Station. The primary objective of the research is to determine the influence of containment on the processing-induced defects and impurity incorporation in germanium-silicon alloy crystals. A comparison will be made between crystals grown by the normal and "detached" Bridgman methods and the ground-based float zone technique. Crystals grown without being in contact with a container have superior quality to otherwise similar crystals grown in direct contact with a container, especially with respect to impurity incorporation, formation of dislocations, and residual stress in crystals. "Detached" or "dewetted" Bridgman growth is similar to regular Bridgman growth in that most of the melt is in contact with the crucible wall, but the crystal is separated from the wall by a small gap, typically of the order of 10-100 microns. Long duration reduced gravity is essential to test the proposed theory of detached growth. Detached growth requires the establishment of a meniscus between the crystal and the ampoule wall. The existence of this meniscus depends on the ratio of the strength of gravity to capillary forces. On Earth, this ratio is large and stable detached growth can only be obtained over limited conditions. Crystals grown detached on the ground exhibited superior structural quality as evidenced by measurements of etch pit density, synchrotron white beam X-ray topography and double axis X-ray diffraction.

Volz, M. P.↗

NASA NTRS2016

Detached Solidification of Germanium-Silicon Crystals on the ISS

Volz, M. P.↗

NASA NTRS1985

Thermal regimes in the detachment fault environment as deduced from fluid inclusions

Extensional tectonism, which dominates middle- and late-Tertiary geology in western Arizona, southeastern California, and southern Nevada, is characterized by normal regionally extensive, low-angle detachment faults. The decollement movement of Fupper plate rocks relative to lower plate assemblages created extensive zones of dilatency, including synthetic and antithetic listric normal faults, tear faults, tectonic crush breccias, shatter breccias, and gash veins in lithologic units above and below the detachment. The tectonically enhanced permeability above and below the detachment fault permitted mass migration of large volumes of hydrothermal solutions along the fault zone during and following upper plate movement. Major quantities of MgO, CaO, K2O, FeO/Fe2O3, SiO2 and CO2 were added to rocks in and near the detachment and related structures. Also introduced were varying amounts of trace elements including Mn, Cu, S, Mo, Ba, Au, Pb, Zn, U and/or Ag. Minerals containing fluid incusions were collected from all of these loci at locations in detachment faulted terranes in western Arizona and southeastern California.

Beane, R. E.↗

NASA NTRS1990

Tertiary structure and thermal history of the Harquahala and Buckskin Mountains, west central Arizona - Implications for denudation by a major detachment fault system

A regional geometrical model for the Whipple-Buckskin-Bullard detachment system (referred to as the Whipple detachment system) is developed. Mineral separates from samples collected in the Harquahala and Buckskin mountains, which lie in the footwall of the Whipple detachment system, are analyzed by the Ar-40/Ar-39 age spectrum technique to determine the cooling history of the mountain range and the age of the metamorphism. Based on the cooling history of the mountains and the bedrock geology of the Harquahala Mountains, the initial geometry of the Whipple detachment system is reconstructed. Next, estimates of slip on the detachment fault and extension within the upper plate terrane are used to determine the regional pattern of extension. The data on the cooling history, structural geometry, and extension pattern are combined into a geometrical model which reconciles the geological data, according to which the breakaway zones represented by the Harquahala Mountains were unroofed by movement on the gently to moderately dipping segment of a great normal fault system as it cut through the upper crust.

Richard, Stephen M.↗

NASA NTRS1998

Bubble Formation and Detachment in Liquid Flow Under Normal and Reduced Gravity

Two-phase flows are present in a wide variety of applications for spacecraft thermal control systems design. Bubble formation and detachment is an integral part of the two-phase flow science. The authors objective is to experimentally investigate the effects of liquid cross velocity, gas velocity, and nozzle diameter on the bubble diameter at detachment under reduced and normal gravity and under relatively low gas flow rates. Results from ground (1 g) and reduced gravity experiments will be presented in this paper. For the 1 g experiment, a flow loop was designed and built to accommodate a range of liquid and gas flow rates. The reduced gravity experiment was conducted on the NASA DC-9 reduced gravity platform using the two-phase flow loop qualified for operation on the low-gravity platform. Flow visualization is accomplished using a high speed 500 frames/s camera. The results suggest that the existence of buoyancy force contributes to the faster detachment of bubbles. Buoyancy helps the detachment process which results in smaller bubbles being formed. In reduced gravity, although drag force is present, the virtual non-existence of buoyant force results in larger bubbles and longer times for detachment. Theoretical predictions are also presented in this paper and seem to agree with the experimental results.

Nahra, Henry K.↗

NASA NTRS2003

Prediction of Bubble Diameter at Detachment from a Wall Orifice in Liquid Cross Flow Under Reduced and Normal Gravity Conditions

Bubble formation and detachment is an integral part of the two-phase flow science. The objective of the present work is to theoretically investigate the effects of liquid cross-flow velocity, gas flow rate embodied in the momentum flux force, and orifice diameter on bubble formation in a wall-bubble injection configuration. A two-dimensional one-stage theoretical model based on a global force balance on the bubble evolving from a wall orifice in a cross liquid flow is presented in this work. In this model, relevant forces acting on the evolving bubble are expressed in terms of the bubble center of mass coordinates and solved simultaneously. Relevant forces in low gravity included the momentum flux, shear-lift, surface tension, drag and inertia forces. Under normal gravity conditions, the buoyancy force, which is dominant under such conditions, can be added to the force balance. Two detachment criteria were applicable depending on the gas to liquid momentum force ratio. For low ratios, the time when the bubble acceleration in the direction of the detachment angle is greater or equal to zero is calculated from the bubble x and y coordinates. This time is taken as the time at which all the detaching forces that are acting on the bubble are greater or equal to the attaching forces. For high gas to liquid momentum force ratios, the time at which the y coordinate less the bubble radius equals zero is calculated. The bubble diameter is evaluated at this time as the diameter at detachment from the fact that the bubble volume is simply given by the product of the gas flow rate and time elapsed. Comparison of the model s predictions was also made with predictions from a two-dimensional normal gravity model based on Kumar-Kuloor formulation and such a comparison is presented in this work.

Nahra, Henry K.↗

NASA NTRS2008

Numerical Investigation of Plasma Detachment in Magnetic Nozzle Experiments

At present there exists no generally accepted theoretical model that provides a consistent physical explanation of plasma detachment from an externally-imposed magnetic nozzle. To make progress towards that end, simulation of plasma flow in the magnetic nozzle of an arcjet experiment is performed using a multidimensional numerical simulation tool that includes theoretical models of the various dispersive and dissipative processes present in the plasma. This is an extension of the simulation tool employed in previous work by Sankaran et al. The aim is to compare the computational results with various proposed magnetic nozzle detachment theories to develop an understanding of the physical mechanisms that cause detachment. An applied magnetic field topology is obtained using a magnetostatic field solver (see Fig. I), and this field is superimposed on the time-dependent magnetic field induced in the plasma to provide a self-consistent field description. The applied magnetic field and model geometry match those found in experiments by Kuriki and Okada. This geometry is modeled because there is a substantial amount of experimental data that can be compared to the computational results, allowing for validation of the model. In addition, comparison of the simulation results with the experimentally obtained plasma parameters will provide insight into the mechanisms that lead to plasma detachment, revealing how they scale with different input parameters. Further studies will focus on modeling literature experiments both for the purpose of additional code validation and to extract physical insight regarding the mechanisms driving detachment.

Sankaran, Kamesh↗

NASA NTRS2003

Residual Gas Effects on Detached Solidification in Microgravity

Many microgravity directional solidification experiments yielded ingots with portions that grew without contacting the ampoule wall, leading to greatly improved crystallographic perfection. Our long-term goal is to make such detached solidification reproducible, which requires a full understanding of the mechanisms underlying it. Our Moving Meniscus Model of steady-state detachment predicts that it depends strongly on the surface tension of the melt and the advancing contact angle with the ampoule wall. Detached solidification is more likely when the contact angle for the melt on the ampoule wall is high, i.e. non-wetting. It has been claimed that impurities increase the contact angle. The objective of the current project is to determine the influence of residual gases on the surface tension and contact angle of molten semiconductors on typical ampoule materials. We are focusing on determining the influence of oxygen on the contact angle of molten InSb on clean silica ('quartz'), including the advancing and retreating contact angles in addition to the usual equilibrium contact angle. We have created a gas flow system that allows us to control the oxygen partial pressure over a sessile drop of InSb on a horizontal quartz surface. The cell is slowly tilted while videotaping to reveal the contact angles on the two sides of the drop just prior to it rolling down the surface. Thus far, we have learned the following: (1) Molten InSb readily forms an oxide layer in the presence of the trace amounts of oxygen found in high purity argon; (2) This oxide contains a substantial amount of Ga, which presumably is a trace contaminant that is not detectable in the starting material; (3) The addition of 10% hydrogen to the argon gas is sufficient to reduce the oxide and produce a clean drop; (4) An infrared filter must precede the video camera in order to produce a sharp image of the drop for later image analysis; (5) Tilting the surface on which the drop rests causes the two sides of the drop to display different contact angles, reflecting contact line sticking; (6) Vibration strongly accelerates the approach of the drop to its final shape on a horizontal surface by helping to overcome sticking of the contact line; (7) Oscillation of the drop surface due to vibration appears to increase as the surface is inclined from horizontal. Presumably, the angle at which the drop rolls down the surface is also reduced by vibration. This observation is particularly significant, as the meniscus must move along the ampoule wall during detached solidification.

Regel, Liya L.↗

NASA NTRS2009

On Favorable Thermal Fields for Detached Bridgman Growth

The thermal fields of two Bridgman-like configurations, representative of real systems used in prior experiments for the detached growth of CdTe and Ge crystals, are studied. These detailed heat transfer computations are performed using the CrysMAS code and expand upon our previous analyses [14] that posited a new mechanism involving the thermal field and meniscus position to explain stable conditions for dewetted Bridgman growth. Computational results indicate that heat transfer conditions that led to successful detached growth in both of these systems are in accordance with our prior assertion, namely that the prevention of crystal reattachment to the crucible wall requires the avoidance of any undercooling of the melt meniscus during the growth run. Significantly, relatively simple process modifications that promote favorable thermal conditions for detached growth may overcome detrimental factors associated with meniscus shape and crucible wetting. Thus, these ideas may be important to advance the practice of detached growth for many materials.

Stelian, Carmen↗

NASA NTRS2002

Bubble Detachment in Variable Gravity Under the Influence of a Non-Uniform Electric Field

The objective of the study reported in this paper is to investigate the effects of variable, reduced gravity on the formation and detachment behavior of individual air bubbles under the influence of a non-uniform electric field. For this purpose, variable gravity experiments were carried out in parabolic nights. The non-uniform electric field was generated by a spherical electrode and a plate electrode. The effect of the magnitude of the non-uniform electric field and gravity level on bubble formation, development and detachment at an orifice was investigated. An image processing code was developed that allows the measurement of bubble volume, dimensions and contact angle at detachment. The results of this research can be used to explore the possibility of enhancing boiling heat transfer in the variable and low gravity environments by substituting the buoyancy force with a force induced by the electric field. The results of experiments and measurements indicate that the level of gravity significantly affects bubble shape, size and frequency. The electric field magnitude also influences bubble detachment, however, its impact is not as profound as that of variable gravity for the range of electric field magnitudes investigated in the present study.

Chang, Shinan↗

NASA NTRS2011

Existence and Stability of Menisci in Detached Bridgman Growth

Detached growth, also referred to as dewetted growth, is a Bridgman crystal growth process in which the melt is in contact with the crucible wall but the crystal is not. A meniscus bridges the gap between the top of the crystal and the crucible wall. The Young-Laplace capillary equation was used to calculate the crystal radii of detached states as a function of the pressure differential across the meniscus. The detached states depend on the contact angle of the melt with the crucible wall, the growth angle of the melt with respect to the solidifying crystal, and the Bond number. A static stability analysis was performed on the calculated detached states. The stability criterion was the sign of the second variation of the potential energy upon admissible meniscus shape perturbations. The conditions considered corresponded to the growth of Ge and InSb, in both terrestrial and microgravity conditions. Stability was found to depend significantly on whether the interior surface was considered to be microscopically rough or smooth, corresponding to pinned or unpinned states. It was also found that all meniscus shapes which are single-valued functions of the radius are statically stable in a microgravity environment.

Volz, M. P.↗

NASA NTRS1974

Plasma tail interpretations of pronounced detached plasma regions measured by Ogo 5

Measurements of the light ion thermal plasma distribution in the magnetosphere frequently show apparent isolated patches of enhanced plasma density in the trough region beyond the main plasmasphere. These patches of light ions viewed along a satellite orbit appear detached from the main plasmasphere. By using a simple time-dependent convection model to determine the length of time a magnetic flux tube has been closed and in daylight (a rough indicator of the expected equatorial plasma density variation), the most prominent 'detached' regions measured by the mass spectrometer on Ogo 5 in the noon-dusk quadrant are seen on a global scale to be readily interpreted as filamentary extensions of the plasmasphere, called plasma tails. Hence on a global scale the pronounced detached regions may be attached to the main plasmasphere.

Chen, A. J.↗

NASA NTRS1978

Detached auroral arcs in the trough region

In a previous paper, Moshupi et al. (1977) have reported on the occurrence of rare auroral 'patches' equatorward of the normally well-defined boundary of diffuse aurora. Some less spectacular but more common arclike features were observed in the same 'trough' region (between the plasmapause and the auroral oval) during the period 1972-1975. These 'detached' arcs show some similarities to stable auroral red arcs in terms of their location and occurrence, but are completely different spectroscopically in that the stable auroral red arcs produce almost pure atomic oxygen red line emissions, whereas the detached arcs are deficient in red line emission - a feature implying totally different production mechanisms. The characteristics of the detached lines are described, including their unusual local time/longitude dependence.

Anger, C. D.↗

NASA NTRS1979

Characteristics of trough region auroral patches and detached arcs observed by Isis 2

All of the data presented in this paper were obtained from the Isis 2 satellite, which was launched into a 1400-km near-circular polar orbit in April 1971. Instruments used in this study include the topside sounder for providing vertical profiles of the electron density, the Langmuir probe for measuring electron temperature and concentration, and the auroral scanning photometer for detecting optical emissions at 5577 A and 3914 A. Two distinct types of auroras (east-west-aligned oval-shaped 'patches', and isolated east-west 'detached arcs') are observed in the trough region (almost exclusively in the Northern Hemisphere) equatorward of the diffuse auroral boundary. Attention is given to comparison of patches and detached arcs, relation to magnetic indices, and relation to detached plasma and ELF hiss.

Moshupi, M. C.↗

NASA NTRS1996

Delay of Turbulent Boundary Layer Detachment by Mechanical Excitation: Application to Rearward-facing Ramp

A vane oscillating about a fixed point at the inlet to a two-dimensional 20 deg rearward-facing ramp proved effective in delaying the detachment of a turbulent boundary layer. Flow-field, surface static pressure, and smoke-wire flow visualization measurements were made. Surface pressure coefficient distributions revealed that two different effects occurred with axial distance along the ramp surface. The surface pressure coefficient varied as a complex function of the vane oscillation frequency and its trailing edge displacement amplitude; that is, it varied as a function of the vane oscillation frequency throughout the entire range of frequencies covered during the test, but it varied over only a limited range of the trailing edge displacement amplitudes covered.The complexity of these findings prompted a detailed investigation, the results of which revealed a combination of phenomena that explain qualitatively how the mechanically generated, periodic, sinusoidal perturbing signal produced by the oscillating vane reacts with the fluid flow to delay the detachment of a turbulent boundary layer experiencing transitory detachment.

McKinzie, Daniel J., Jr.↗

NASA NTRS1999

Improved Crystal Quality by Detached Solidification in Microgravity

Directional solidification in microgravity has often led to ingots that grew with little or no contact with the ampoule wall. When this occurred, crystallographic perfection was usually greatly improved -- often by several orders of magnitude. Unfortunately, until recently the true mechanisms underlying detached solidification were unknown. As a consequence, flight experiments yielded erratic results. Within the past four years, we have developed a new theoretical model that explains many of the flight results. This model gives rise to predictions of the conditions required to yield detached solidification, both in microgravity and on earth. A discussion of models of detachment, the meniscus models and results of theoretical modeling, and future plans are presented.

Regel, Liya L.↗

NASA NTRS1999

Detached Growth of Germanium and Germaniumsilicon

Up to now, detached growth was observed mainly under microgravity, i.e. under the absence of hydrostatic pressure that hinders the formation of a free melt meniscus. the detached growth of germanium doped with gallium was obtained under 1 g conditions, the growth was performed in quartz-glass ampoule. Part of the crystal grew without wall contact, the detached growth was observed in-situ with a CCD-camera as well as after the growth process in form of growth lines and the formation of <111> facets on the crystal surface. GeSi crystal (oriientation: <111>, maximum silicon content: 4 at%, seed material: Ge) was grown in a pBN crucible (excluding the possibility of in-situ monitoring of the growth process). The grown crystal exhibits three growth facets, indicating also wall free growth. Surface analysis of the crystals (NDIC, SEM) and characterization of crystal segregation (EDAX, resistivity measurement) and defect structure (EPD, x-ray diffraction measurements) will be presented.

Dold, P.↗