An overview of NASA's Space Station program
NASA space station program, discussing relationship between space stations, Skylab and space shuttle, electric power generation, habitability, safety and communications networks
Lohman, R. L.↗
SEARCH · Search NASA
Results for “electric shuttles”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Advanced fuel cell concepts for future NASA missions
Studies of primary fuel cells for advanced all electric shuttle type vehicles show an all fuel cell power system with peak power capability of 100's of kW to be potentially lighter and have lower life cycle costs than a hybrid system using advanced H2O2 APU's for peak power and fuel cells for low power on orbit. Fuel cell specific weights of 1 to 3 lb/kW, a factor of 10 improvement over the orbiter power plant, are projected for the early 1990's. For satellite applications, a study to identify high performance regenerative hydrogen oxygen fuel cell concepts for geosynchronous orbit was completed. Emphasis was placed on concepts with the potential for high energy density (Wh/lb) and passive means for water and heat management to maximize system reliability. Both alkaline electrolyte and polymer membrane fuel cells were considered.
Stedman, J. K.↗
Small Mercury Ion Clock for On-board Spacecraft Navigation
I.Small Ion Clock Approach and Heritage: a) No lasers, uwave cavities, cryogenics, atomic beams, etc. b) Ions are electrically shuttled between separate optical and microwave traps. II. Each trap is optimized for its task: quadrupole for optical state selection; multi-pole for microwave clock. a) Very good stability shown in USNO. Timescale running "open loop." III. "Open loop" operation means no self-measurements of frequency offsets: (Zeeman, ion temperature,... etc.) a) Fewer parts and procedures, produces stable output continuously. IV. Ion clock is not so sensitive to temperature fluctuations a) Measured u:nshielded temperature coefficient of few 10(exp -15) per C. b) No bulky temperature isolation needed.
Prestage, John D.↗
Electrical power generation subsystem for Space Shuttle Orbiter
The requirements, capabilities, and design of the Space Shuttle Orbiter electrical power generation (EPG) subsystem are presented. The Orbiter EPG subsystem is designed to have the flexibility to supply the basic Orbiter electrical loads and the power requirements of the payloads which, in some cases, are completely dependent on the Orbiter for both power and heat rejection. These needs are supplied by three hydrogen/oxygen fuel cell powerplants (FCPs), having the capability of providing a total of 14 kW average and up to 24 kW peak in the basic Orbiter configuration. Kits permit dedication of one FCP to the payload by providing an additional reactant tank pair for a seven-day mission and additional heat rejection capability.
Blaski, M. F.↗
A candidate mission using the Shuttle and solar electric propulsion
It is suggested that an out-of-the-ecliptic solar electric propulsion (SEP) mission be performed. Data would be gathered pertaining to the three-dimensional structure of solar features at radio and X-ray wavelengths, the properties of the solar wind as a function of latitude and time, the configuration of the interplanetary field and its relation to solar fields, and the modulations of cosmic rays to determine the spectrum of interstellar cosmic rays. The mission would also, it is thought, demonstrate the capability of SEP for use in Shuttle missions. The SEP spacecraft and the ongoing development of related systems are examined. The weight of a SEP stage is contrasted with the weight of a chemical rocket stage.
Duxbury, J. H.↗
Power processing and distribution for the space shuttle craft
Electric power processing and distribution system for space shuttle vehicles
Schwarz, F. C.↗
Lightning criteria relative to space shuttles: Currents and electric field intensity in Florida lightning
The measured electric field intensities of 161 lightning strokes in 39 flashes which occurred between 1 and 35 km from an observation point at Kennedy Space Center, Florida during June and July of 1971 have been analyzed to determine the lightning channel currents which produced the fields. In addition, typical channel currents are derived and from these typical electric fields at distances between 0.5 and 100 km are computed and presented. On the basis of the results recommendations are made for changes in the specification of lightning properties relative to space vehicle design as given in NASA TMX-64589 (Daniels, 1971). The small sample of lightning analyzed yielded several peak currents in the 100 kA range. Several current rise-times from zero to peak of 0.5 microsec or faster were found; and the fastest observed current rate-of-rise was near 200 kA/microsec. The various sources of error are discussed.
Uman, M. A.↗
Electrical behavior of a Shuttle Electrodynamic Tether System /SETS/
Many novel electrodynamic and space plasma physics experiments can be done from the space shuttle using a gravity gradient stabilized subsatellite tethered 10-30 km above the Orbiter via a long, conducting wire which is insulated from the ionospheric plasma. This system, called the Shuttle Electrodynamic Tether System (SETS), is described in the present paper with emphasis upon the various electrical processes which determine its coupling to the ambient plasma. The three most important physical effects include sheath formation and electron collection by the subsatellite, the generation of a large emf through the orbital motion of the tether across geomagnetic field lines, and the active ejection of electrons from the Orbiter into the surrounding ionosphere. An electrical circuit analogy is presented for SETS together with a brief outline of possible areas related to the artificial generation of magnetohydrodynamic waves.
Banks, P. M.↗
Electrical design of Space Shuttle payload G-534: The pool boiling experiment
Payload G-534, the Pool Boiling Experiment (PBE), is a Get Away Special (GAS) payload that flew on the Space Shuttle Spacelab Mission J (STS 47) on September 19-21, 1992. This paper will give a brief overall description of the experiment with the main discussion being the electrical design with a detailed description of the power system and interface to the GAS electronics. The batteries used and their interface to the experiment Power Control Unit (PCU) and GAS electronics will be examined. The design philosophy for the PCU will be discussed in detail. The criteria for selection of fuses, relays, power semiconductors, and other electrical components along with grounding and shielding policy for the entire experiment are presented. The intent of this paper is to discuss the use of military tested parts and basic design guidelines to build a quality experiment for minimal additional cost.
Francisco, David R.↗
Line Replaceable Unit Analysis
Shuttle LRU (Line Replaceable Unit) Analysis Program (SLAP) aids in evaluation of LRU interface voltages in Shuttle orbiter electrical system. Slap includes reduced model of Shuttle LRU circuit. Although primarily intended for analysis of Shuttle LRU's SLAP could be adapted for voltage analysis in other situations.
Oepomo, T.↗
Temperature and Frequency Dependent Electrical Properties of AVCOAT and Shuttle Tile Material
This technical memorandum presents the data and results from a series of tests performed on AVCOAT, charred AVCOAT, and different Shuttle Thermal Protection System (TPS) tile coatings to determine their electrical properties as a function of temperature and frequency. Initially, the samples were assumed to be insulators and the complex permittivities were measured from data collected by sandwiching each sample between two conductors to form a sandwich. However, the AVCOAT sample data showed that the material becomes conductive as it begins to char. To get an accurate conductivity reading on these charred samples, a four-point resistance probe was used to collect data. Overall, this testing showed that the virgin AVCOAT starts out as a material that is a good insulator but transitions to one with a conductivity on the order of 1860 S/m as it chars. The deeper layers of AVCOAT (un-charred) all exhibited a temperature and frequency dependence that is possibly indicative of a dielectric relaxation in the material. As the sample temperatures were increased, a knee appears in the real permittivity data sets below 1 kHz. Both the real permittivity and resistivity drop up to several orders of magnitude yet show that the material remains an insulator. The Shuttle High Temperature Reusable Surface Insulation (HRSI) tile coatings studied included Reac- tion Cured Glass (RCG), Aluminum Enhanced Thermal Barrier (AETB), and Toughened Unipiece Fibrous Insulation (TUFI). The purely glass fiber parts of the tile were removed leaving only the outer layers con- taining just the coating. The data collected shows that the RCG, AETB, and outermost layer of the TUFI have similar electrical properties. The real permittivity plots show that there appears to be a relaxation that shows up at frequencies below 1 kHz. The relaxation frequency increases with increasing temperature. Also, the real permittivity increases up to about a factor of four between room temperature and 650K. Likewise, the resistivity (related to the imaginary permittivity) decreases up to five orders of magnitude over the same temperature interval, but still remains an insulator. This data was collected to support a NASA Engineering and Safety Center (NESC) assessment team investigating the source of thermocouple anomalies in both Shuttle TPS material and AVCOAT used for on the Orion spacecraft for Exploration Flight Test 1 (EFT-1). The details of their findings will be documented in a separate report with this document serving as a reference.
Mark A Nurge↗
Concept for a shuttle-tended reusable interplanetary transport vehicle using nuclear electric propulsion
Explore the source record for details and available documents.
interplanetary nuclear electric propulsion shuttle↗
Concept for a shuttle-tended reusable interplanetary transport vehicle using nuclear electric propulsion
NASA has placed new emphasis on the development of advanced propulsion technologies including Nuclear Electric Propulsion (NEP). This technology would provide multiple benefits including high delta-V capability and high power for long duration spacecraft operations.
interplanetary nuclear electric propulsion shuttle↗
Development of generalized 3-D braiding machines for composite preforms
The development of prototype braiding machines for the production of generalized braid patterns is described. Mechanical operating principles and control strategies are presented for two prototype machines which have been fabricated and evaluated. Both machines represent advances over current fabrication techniques for composite materials by enabling nearly ideal control of fiber orientations within preform structures. They permit optimum design of parts that might be subjected to complex loads or that have complex forms. Further, they overcome both the lack of general control of produced fiber architectures and the complexity of other weaving processes that have been proposed for the same purpose. One prototype, the Farley braider, consists of an array of turntables that can be made to oscillate in 90 degree steps. Yarn ends are transported about the surface formed by the turntables by motorized tractors which are controlled through an optical link with the turntables and powered through electrical contact with the turntables. The necessary relative motions are produced by a series of linear tractor moves combined with a series of turntable rotations. As the tractors move about, they weave the yarn ends into the desired pattern. The second device, the shuttle plate braider, consists of a braiding surface formed by an array of stationary square sections, each separated from its neighbors by a gap. A plate beneath this surface is caused to reciprocate in two perpendicular directions, first in one direction and then in the other. This movement is made possibly by openings in the plate that clear short columns supporting the surface segments. Yarn ends are moved about the surface and interwoven by shuttles which engage the reciprocating plate as needed to yield the desired movements. Power and control signals are transmitted to the shuttles through electrical contact with the braiding surface. The shuttle plate is a passively driven prime mover that supplies the power to move all shuttles and the shuttles are simple devices that employ only a solenoid to engage the shuttle plate on command. Each shuttle is assigned a unique identity and is controlled independently. When compared to each other, the Farley braider is felt to have the advantage of speed and the shuttle plate braider, the advantage of simplicity.
Huey, Cecil O., Jr.↗
Manned spacecraft electrical power systems
A brief history of the development of electrical power systems from the earliest manned space flights illustrates a natural trend toward a growth of electrical power requirements and operational lifetimes with each succeeding space program. A review of the design philosophy and development experience associated with the Space Shuttle Orbiter electrical power system is presented, beginning with the state of technology at the conclusion of the Apollo Program. A discussion of prototype, verification, and qualification hardware is included, and several design improvements following the first Orbiter flight are described. The problems encountered, the scientific and engineering approaches used to meet the technological challenges, and the results obtained are stressed. Major technology barriers and their solutions are discussed, and a brief Orbiter flight experience summary of early Space Shuttle missions is included. A description of projected Space Station power requirements and candidate system concepts which could satisfy these anticipated needs is presented. Significant challenges different from Space Shuttle, innovative concepts and ideas, and station growth considerations are discussed. The Phase B Advanced Development hardware program is summarized and a status of Phase B preliminary tradeoff studies is presented.
Simon, William E.↗
Electric auxiliary power unit for Shuttle evolution
The Space Shuttle Orbiter currently uses three hydrazine fueled auxiliary power units (APUs) to provide hydraulic power for the vehicle aerodynamic surface controls, main engine thrust vector control, landing gear, steering, and brakes. Electric auxiliary power units have been proposed as possible replacements to the hydrazine auxiliary power units. Along with the potential advantages, this paper describes an Electric APU configuration and addresses the technical issues and risks associated with the subsystem components. Additionally, characteristics of an Electric APU compared to the existing APU and the direction of future study with respect to the Electric APU is suggested.
Meyer, Doug↗
The prevention of electrical breakdown and electrostatic voltage problems in the space shuttle and its payloads. Part 1: Theory and phenomena
An introduction to the theory of corona discharge and electrostatic phenomena is presented. The theory is mainly qualitative so that workers in the field should not have to go outside this manual for an understanding of the relevant phenomena. Some of the problems that may occur with the space shuttle in regard to electrical discharge are discussed.
Whitson, D. W.↗
Launch-Off-Need Shuttle Hubble Rescue Mission: Medical Issues
The Space Shuttle Hubble repair mission (STS-125) is unique in that a rescue mission (STS-400) has to be ready to launch before STS-125 life support runs out should the vehicle become stranded. The shuttle uses electrical power derived from fuel cells that use cryogenic oxygen and hydrogen (CRYO) to run all subsystems including the Environmental Control System. If the STS-125 crew cannot return to Earth due to failure of a critical subsystem, they must power down all nonessential systems and wait to be rescued by STS-400. This power down will cause the cabin temperature to be 60 F or less and freeze the rest of the vehicle, preventing it from attempting a reentry. After an emergency has been declared, STS-125 must wait at least 7 days to power down since that is the earliest that STS-400 can be launched. Problem The delayed power down of STS-125 causes CYRO to be consumed at high rates and limits the survival time after STS-400 launches to 10 days or less. CRYO will run out sooner every day that the STS-400 launch is delayed (weather at launch, technical issues etc.). To preserve CRYO and lithium hydroxide (LiOH - carbon dioxide removal) the crew will perform no exercise to reduce their metabolic rates, yet each deconditioned STS-125 crewmember must perform an EVA to rescue himself. The cabin may be cold for 10 days, which may cause shivering, increasing the metabolic rate of the STS-125 crew. Solution To preserve LiOH, the STS-125 manifest includes nutrition bars with low carbohydrate content to maintain crew respiratory quotient (RQ) below 0.85 as opposed to the usual shuttle galley food which is rich in carbohydrates and keeps the RQ at approximately 0.95. To keep the crew more comfortable in the cold vehicle warm clothing also has been included. However, with no exercise and limited diet, the deconditioned STS-125 crew returning on STS-400 may not be able to egress the vehicle autonomously requiring a supplemented crash-and-rescue capability.
Hamilton, Douglas↗