SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The analysis and design of a GaAlAs Mach-Zehnder electrooptic modulator operating at 820 nm is presented. Optical modulation is achieved through coplanar 50-ohm traveling-wave microwave electrodes with a resulting 3-dB bandwidth-length product of 11.95 GHz cm.
The present article addresses itself to the prime power requirements of a coupling-modulated gas laser transmitter. The latter consists of a gas discharge tube and electrooptic modulator inside a laser resonator. In performing the calculations, the laser discharge length and the modulator voltage are simultaneously varied so that the transmitted power remains constant. In this way, tradeoffs can be made between the prime power supplied individually to the discharge tube and to the modulator driver to obtain a transmitter configuration that minimizes the total prime power consumption. An analytical expression is derived that describes the effects of information bandwidth and transmitter output power on the prime power requirements. Specific numerical results are obtained for a CO2 laser transmitter based on presently available experimental data.
A method is developed for directly measuring atmospheric winds in the 20-120 km altitude interval from a spacecraft. The wind sensor measures the Doppler shift between the spectral absorption lines of a gas in a cell within the instrument and the thermal emission lines of the same gas in the atmosphere. The wind measurements are performed using a spacecraft-borne gas correlation spectrometer viewing the limb of the atmosphere. The wind-induced Doppler shift between the two spectra, and thus the magnitude of the wind itself, is obtained by phase modulating the incoming thermal radiation (equivalent to frequency modulation) by means of an electrooptically active crystal to determine the frequency shift required to reestablish exact correlation between the lines in the cell and the lines from the atmosphere. Results of numerical simulations of the wind-sensor performance indicate that the noise-equivalent-wind is between 1-5 m/s over most of the stratosphere and mesosphere.
A technique which can provide frequency doubling, with high efficiency, while cavity dumping a laser for pulse position M-ary modulation while being used for an optical communication link is discussed. This approach uses a secondary cavity that provides feedback of the undoubled fundamental light, which is normally lost, into the primary cavity to be recirculated and frequency doubled. Specific operations of the electrooptic modulator and frequency-doubling crystal are described along with the overall modulation scheme and experimental setup.
The paper describes an electronic heterodyne recording which uses electrooptic modulation to introduce a sinusoidal phase shift between the object and reference wave. The resulting temporally modulated holographic interference pattern is scanned by a commercial image dissector camera, and the rejection of the self-interference terms is accomplished by heterodyne detection at the camera output. The electrical signal representing this processed hologram can then be used to modify the properties of a liquid crystal light valve or a similar device. Such display devices transform the displayed interference pattern into a phase modulated wave front rendering a three-dimensional image.
A theory for strongly coupled waveguides is discussed and applied to two- and three-waveguide couplers and optical wavelength filters. This theory makes use of an exact analytical relation governing the coupling coefficients and the overlap integrals. It removes almost all of the constraints imposed by a simpler and approximate coupled-mode theory by Marcatili (1986). It also satisfies the energy conservation and the reciprocity theorem self-consistently. Very good numerical results with the overlap integral as large as 49 percent are shown. The applications to electrooptical modulators, power dividers, power transfer devices, and optical filters are all presented with numerical results.
Theoretical and applications aspects of optoelectronic control for microwave devices are examined in an introduction for graduate engineering students and practicing engineers. The basic features of optical MMICs are reviewed, and chapters are devoted to laser diodes, electrooptic modulators, photodetectors, microwave fiber-optic links, optoelectronic switching and gating, optoelectronic microwave signal generation, an optoelectronic switch matrix, optoelectronic switching and modulation of oscillators, and optoelectronic injection-locking and tuning of oscillators. Extensive diagrams, drawings, and graphs are provided.
Based on an efficient broadband electrooptic modulator producing RF optical sidebands locked to a stable cavity, a tunable dye laser can be scanned under computer control with frequency-synthesizer precision. Cavity drift is suppressed in software by using a strong feature in the spectrum for stabilization. Mercury isotope shifts are measured with a reproducibility of about 50 kHz. This accuracy of about 1/300 of the linewidth illustrates the power of the technique. Derived hyperfine-structure constants are compared with previous atomic-beam data.
NASA-Lewis has developed wavelength-multiplexed digital position fiber-optics transducers for use in aircraft control systems. A prototype LED-powered rotary encoder for a commercial aircraft turbofan engine is under construction which will have 8-bit resolution and an operational temperature in the 90 C range. A compact electrooptics module is also under development which will be able to withstand gas turbine environments. A second-generation device will incorporate integrated photonics technologies to increase optical power margin.
The development of novel electro-optic spatial light modulators (both one and two dimensional) which allows real-time coherent optical SAR processors to be implemented is outlined. It is suggested that the availability of such processors may initiate new mission applications not presently envisioned due to current digital processor limitations.
A parametric study was conducted to develop an electrooptic waveguide modulator for generating continuous tunable sideband power from an infrared CO2 laser. Parameters included were the waveguide configurations, microstrip dimensions device impedance, and effective dielectric constants. An optimum infrared laser modulator was established and was fabricated. This modulator represents the state-of-the-art integrated optical device, which has a three-dimensional topology to accommodate three lambda/4 step transformers for microwave impedance matching at both the input and output terminals. A flat frequency response of the device over 20 HGz or = 3 dB) was achieved. Maximum single sideband to carrier power greater than 1.2% for 20 W microwave input power at optical carrier wavelength of 10.6 microns was obtained.
New type of correlation spectrometer eliminates need to shift between two cells, one empty and one containing reference gas. Electrooptical phase modulator sinusoidally shift frequencies of sample transmission spectrum.
A proposed instrument would project a narrow laser beam that would be frequency-modulated with a pseudorandom noise (PN) code for simultaneous measurement of range and velocity along the beam. The instrument performs these functions in a low mass, power, and volume package using a novel combination of established techniques. Originally intended as a low resource- footprint guidance sensor for descent and landing of small spacecraft onto Mars or small bodies (e.g., asteroids), the basic instrument concept also lends itself well to a similar application guiding aircraft (especially, small unmanned aircraft), and to such other applications as ranging of topographical features and measuring velocities of airborne light-scattering particles as wind indicators. Several key features of the instrument s design contribute to its favorable performance and resource-consumption characteristics. A laser beam is intrinsically much narrower (for the same exit aperture telescope or antenna) than a radar beam, eliminating the need to correct for the effect of sloping terrain over the beam width, as is the case with radar. Furthermore, the use of continuous-wave (CW), erbium-doped fiber lasers with excellent spectral purity (narrow line width) permits greater velocity resolution, while reducing the laser s power requirement compared to a more typical pulsed solid-state laser. The use of CW also takes proper advantage of the increased sensitivity of coherent detection, necessary in the first place for direct measurement of velocity using the Doppler effect. However, measuring range with a CW beam requires modulation to "tag" portions of it for time-of-flight determination; typically, the modulation consists of a PN code. A novel element of the instrument s design is the use of frequency modulation (FM) to accomplish both the PN-modulation and the Doppler-bias frequency shift necessary for signed velocity measurements. This permits the use of a single low-power waveguide electrooptic phase modulator, while simultaneously mitigating the effects of speckle as a noise source in the coherent detection.
Classical optical frequency combs have revolutionized a myriad of fields, from optical spectroscopy and optical clocks to arbitrary microwave synthesis and lightwave communication. Capitalizing on the inherent robustness and high dimensionality of this mature optical platform, their nonclassical counterparts, so-called “quantum frequency combs,” have recently begun to display significant promise for fiber-compatible quantum information processing (QIP) and quantum networks. In this review, the basic theory and experiments of frequency-bin QIP, as well as perspectives on opportunities for continued advances, will be covered. Finally, particular emphasis is placed on the recent demonstration of the quantum frequency processor (QFP), a photonic device based on electro-optic modulation and Fourier-transform pulse shaping that is capable of realizing high-fidelity quantum frequency gates in a parallel, low-noise fashion.
Herein, we propose an electro-optic approach for transparent optical networking, in which frequency channels are actively transformed into any desired mapping in a wavelength-multiplexed environment. Based on electro-optic phase modulators and Fourier-transform pulse shapers, our all-optical frequency processor (AFP) is examined numerically for the specific operations of frequency channel hopping and broadcasting, and found capable of implementing these transformations with favorable component requirements. Extending our analysis via a mutual-information–based metric for system optimization, we show how to optimize transformation performance under limited resources in a classical context, contrasting the results with those found using metrics motivated by quantum information, such as fidelity and success probability. Given its compatibility with on-chip implementation, as well as elimination of optical-to-electrical conversion in frequency channel switching, the AFP looks to offer valuable potential in silicon photonic network design, as well as the realization of high-dimensional frequency-bin gates.
This work describes a novel optical heterodyne detection scheme that significantly extends the frequency response of the phase contrast imaging method to detect electron density fluctuations in tens of megahertz frequency range. The system employs a variable frequency electro-optic modulator to allow operation at any frequency in the range 10–40 MHz without the need to realign the system. The frequency coverage of the system makes it suitable to measure the radial structure of the electron density component of ion cyclotron emission on devices having confining magnetic field of a few tesla, thus extending the purely temporal measurements provided so far by magnetic probes.
Frequency-bin qubits possess unique synergies with wavelength-multiplexed lightwave communications, suggesting valuable opportunities for quantum networking with the existing fiber-optic infrastructure. Although the coherent manipulation of frequency-bin states requires highly controllable multi-spectral-mode interference, the quantum frequency processor (QFP) provides a scalable path for gate synthesis leveraging standard telecom components. Here, we summarize the state of the art in experimental QFP characterization. Distinguishing between physically motivated “open box” approaches that treat the QFP as a multiport interferometer, and “black box” approaches that view the QFP as a general quantum operation, we highlight the assumptions and results of multiple techniques, including quantum process tomography of a tunable beamsplitter—to our knowledge the first full process tomography of any frequency-bin operation. Our findings should inform future characterization efforts as the QFP increasingly moves beyond proof-of-principle tabletop demonstrations toward integrated devices and deployed quantum networking experiments.
Real- and nonreal-time optical image subtraction (OIS) techniques are reviewed. Real-time OIS techniques include source encoding, polarization modulation, pseudocolor image difference detection, the holographic shear lens technique, and nonlinear optics. Included in the nonreal-time category are speckle diffuser encoding, speckle-pattern encoding, halftone screen encoding, and polarization-shifted encoding. It is concluded that the most useful techniques are the real-time operations. It is noted that some nonreal-time optical techniques can be applied directly while others may be converted into real-time ones through the use of advance real-time spatial light modulators or electrooptic devices.