Search NASA⌕ Search

SEARCH · Search NASA

Results for “electrospun”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Electrospun Si and Si/C Fiber Anodes for Li-Ion Batteries

Due to structural changes in silicon during lithiation/delithiation, most Li-ion battery anodes containing silicon show rapid gravimetric capacity fade upon charge/discharge cycling. Herein, we report on a new Si powder anode in the form of electrospun fibers with only poly(acrylic acid) (PAA) binder and no electrically conductive carbon. The performance of this anode was contrasted to a fiber mat composed of Si powder, PAA binder, and a small amount of carbon powder. Fiber mat electrodes were evaluated in half-cells with a Li metal counter/reference electrode. Without the addition of conductive carbon, a stable capacity of about 1500 mAh/g (normalized to the total weight of the anode) was obtained at 1C for 50 charge/discharge cycles when the areal loading of silicon was 0.30 mgSi/cm2, whereas a capacity of 800 mAh/g was obtained when the Si loading was increased to ~1.0 mgSi/cm2. On a Si weight basis, these capacities correspond to >3500 mAh/gSi. The capacities were significantly higher than those found with a slurry-cast powdered Si anode with PAA binder. There was no change in fiber anode performance (gravimetric capacity and constant capacity with cycling) when a small amount of electrically conductive carbon was added to the electrospun fiber anodes when the Si loading was ≤1.0 mgSi/cm2.

Mondal, Abhishek N.↗
DOE OSTI2020

A “Graft to” Electrospun Zwitterionic Bilayer Membrane for the Separation of Hydraulic Fracturing-Produced Water via Membrane Distillation

Simultaneous fouling and pore wetting of the membrane during membrane distillation (MD) is a major concern. In this work, an electrospun bilayer membrane for enhancing fouling and wetting resistance has been developed for treating hydraulic fracture-produced water (PW) by MD. These PWs can contain over 200,000 ppm total dissolved solids, organic compounds and surfactants. The membrane consists of an omniphobic surface that faces the permeate stream and a hydrophilic surface that faces the feed stream. The omniphobic surface was decorated by growing nanoparticles, followed by silanization to lower the surface energy. An epoxied zwitterionic polymer was grafted onto the membrane surface that faces the feed stream to form a tight antifouling hydration layer. The membrane was challenged with an aqueous NaCl solution containing sodium dodecyl sulfate (SDS), an ampholyte and crude oil. In the presence of SDS and crude oil, the membrane was stable and displayed salt rejection (>99.9%). Further, the decrease was much less than the base polyvinylidene difluoride (PVDF) electrospun membrane. The membranes were also challenged with actual PW. Our results highlight the importance of tuning the properties of the membrane surface that faces the feed and permeate streams in order to maximize membrane stability, flux and salt rejection.

omniphobic↗
DOE OSTI2022

U(VI) binding onto electrospun polymers functionalized with phosphonate surfactants

We previously observed that phosphonate functionalized electrospun nanofibers can uptake U(VI), making them promising materials for sensing and water treatment applications. Here, we investigate the optimal fabrication of these materials and their mechanism of U(VI) binding under the influence of environmentally relevant ions (e.g., Ca 2+ and CO 3 2- ). We found that U(VI) uptake was greatest on polyacrylonitrile (PAN) functionalized with longer-chain phosphonate surfactants (e.g., hexa- and octadecyl phosphonate; HDPA and ODPA, respectively), which were better retained in the nanofiber after surface segregation. Subsequent uptake experiments to better understand specific solid-liquid interfacial interactions were carried out using 5 mg of HDPA-functionalized PAN mats with 10 μM U at pH 6.8 in four systems with different combinations of solutions containing 5 mM calcium (Ca 2+ ) and 5 mM bicarbonate (HCO 3 -). U uptake was similar in control solutions containing no Ca 2+ and HCO 3 - (resulting in 19 ± 3% U uptake), and in those containing only 5 mM Ca2+ (resulting in 20 ± 3% U uptake). A decrease in U uptake (10 ± 4% U uptake) was observed in experiments with HCO 3 -, indicating that UO 2 -CO 3 complexes may increase uranium solubility. Results from shell-by-shell EXAFS fitting, aqueous extractions, and surface-enhanced Raman scattering (SERS) indicate that U is bound to phosphonate as a monodentate inner sphere surface complex to one of the hydroxyls in the phosphonate functional groups. New knowledge derived from this study on material fabrication and solid-liquid interfacial interactions will help to advance technologies for use in the in-situ detection and treatment of U in water.

42 ENGINEERING↗
DOE OSTI2020

Phase-contrast 3D tomography of HeLa cells grown in PLLA polymer electrospun scaffolds using synchrotron X-rays

Advanced imaging is useful for understanding the three-dimensional (3D) growth of cells. X-ray tomography serves as a powerful noninvasive, nondestructive technique that can fulfill these purposes by providing information about cell growth within 3D platforms. There are a limited number of studies taking advantage of synchrotron X-rays, which provides a large field of view and suitable resolution to image cells within specific biomaterials. In this study, X-ray synchrotron radiation microtomography at Diamond Light Source and advanced image processing were used to investigate cellular infiltration of HeLa cells within poly L-lactide (PLLA) scaffolds. This study demonstrates that synchrotron X-rays using phase contrast is a useful method to understand the 3D growth of cells in PLLA electrospun scaffolds. Two different fiber diameter (2 and 4 µm) scaffolds with different pore sizes, grown over 2, 5 and 8 days in vitro , were examined for infiltration and cell connectivity. After performing visualization by segmentation of the cells from the fibers, the results clearly show deeper cell growth and higher cellular interconnectivity in the 4 µm fiber diameter scaffold. Finally, this indicates the potential for using such 3D technology to study cell–scaffold interactions for future medical use.

3D culture↗
DOE OSTI2023

Encapsulation of Nanoparticle Organic Hybrid Materials within Electrospun Hydrophobic Polymer/Ceramic Fibers for Enhanced CO 2 Capture

Liquid-like nanoparticle organic hybrid materials (NOHMs) consisting of a silica core with ionically grafted branched polyethyleneimine chains (referred to as NIPEI) are encapsulated within submicron-scale polyacrylonitrile (PAN)/polymer-derived-ceramic electrospun fibers. The addition of a room-temperature curable, liquid-phase organopolysilazane (OPSZ) ceramic precursor to the PAN/NOHM solution enhances the internal dispersion of NOHMs and forms a thin ceramic sheath layer on the fiber exterior, shielding the hydrophilic NIPEI to produce near-superhydrophobic non-woven fiber mats with contact angles exceeding 140°. 60:40 loadings of NOHMs to PAN/OPSZ can be reliably achieved with low OPSZ percentages required, and up to 4:1 NOHM:polymer loadings are possible before losing hydrophobicity. These fibers demonstrate up to ≈2 mmol CO 2 g -1 fiber capture capacities in a pure CO 2 atmosphere through the nonwoven fibrous networks and the permeability of the OPSZ shell. In conclusion, the hybrid fibers additionally show enhanced capture kinetics under pure CO 2 and 400 ppm CO 2 conditions, indicating their promising application as a direct air capture platform.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Thermoplastic Elastomers and Their Physical Gels Electrospun into Tunable Microfibrous Nonwoven Mats: Structure Formation and Property Enhancement

Abstract Thermoplastic elastomers (TPEs) based on styrenic block copolymers constitute excellent examples of self‐networking macromolecules that are employed in a wide range of contemporary technologies as molded parts. In such applications, these TPEs exist as dense (nonporous) films or other shapes. Here, it is first demonstrated that a series of commercial TPEs possessing comparable compositions can be electrospun from solution to form microfibers that are arranged into nonwoven mats that are breathable. An important consideration for microfiber formation is the copolymer molecular weight, which regulates i) the viscosity of the parent solution prior to electrospinning, ii) the ability of these copolymers to self‐assemble during electrospinning, iii) the microfiber morphology, and iv) the mechanical properties of the resultant microfibers. The addition of a midblock‐selective aliphatic oil to these TPEs yields thermoplastic elastomer gels (TPEGs), wherein the copolymer morphology and mechanical properties become highly composition‐tunable. Electrospinning TPEGs from a binary oil+solvent solution introduces a micelle inversion mechanism that begins with an oil‐rich micellar core and ends with a styrene‐rich micellar core, required for network stabilization, as the solvent dries during microfiber solidification. This work has implications for the production of controllably low‐modulus microfibrous materials possessing modestly improved toughness but exceptional extensibility and enhanced optical transparency.

Shamsi, Mohammad↗
DOE OSTI2021

Manipulating cobalt oxide on N-doped aligned electrospun carbon nanofibers towards instant electrochemical detection of dopamine secreted by living cells

A demand exists for the development of miniaturized biosensors with high sensitivity and a wide dynamic range for rapid detecting dopamine (DA) levels. Here, an electrochemical sensor is created by decorating closely packed cobalt oxide (Co 3 O 4 ) nanograins on nitrogen-doped electrospun carbon nanofibers (NECNFs) via a facile electrodeposition method. The carbon nanofiber matrix provides both a scaffold with ultrahigh surface area for homogeneous dispersion of cobalt oxide nanostructures and facilitates the electrochemical conductivity for the hybrid electrode. The sensing principle is based on the redox reaction between DA and DA quinone that generates electrical signal, which is detectable via differential pulse voltammetry (DPV) and chronoamperometry (CA). Owing to a high electroactive surface area and facilitating electron transfer between electrode surface and the target molecule, the electrical sensing platform exhibits superior sensitivity and selectivity toward DA, with an excellent limit of detection (9 nM) over a wide range of concentrations (0.01 to 100 μM). Moreover, based on its excellent sensing properties and biocompatibility, the sensor has been used for the real-time monitoring exogeneous DA released from pheochromocytoma (PC12) cells. This work demonstrates promise of a novel sensor technology that may render rapid point-of-care testing of DA towards early clinical diagnosis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Hierarchically porous electrospun carbon nanofiber for high-rate capacitive deionization electrodes

Capacitive deionization (CDI) is a promising technology that has gained interest for the desalination of brackish water. Hierarchically porous carbons are commonly used as electrodes for CDI due to their high surface areas and controlled pore size distributions that maximize ion adsorption capacity and rate. Electrospinning is an effective way of generating carbon nanofibers with high inter-fiber macroporosity that can be further modified to improve surface area, total pore volume, and pore size distribution. This work describes the use of sacrificial mesopore formers in tandem with a micropore etching technique to induce hierarchical porosity in electrospun fibers. Mesopores are formed via the dissolution of silica nanoparticles that are introduced into the fibers during the electrospinning step. After mesopore formation, micropores are etched into the resulting surface through KOH impregnation and thermal activation. This sequential technique creates a hierarchical network of pores from the inherent macroporosity of the fiber network, to the mesopores, and finally micropores to simultaneously maximize surface area and accessibility. Micropore formation is optimized to maximize specific surface area while maintaining physical integrity of the fibers. Further, the combination of mesopores and micropores enables fast ion adsorption rates and capacity. Carbon fiber electrodes fabricated in this method achieve specific surface areas exceeding 1400 m 2 g -1 , with pore volumes exceeding 1.0cc g -1 . The pore size distributions are highly controlled, with 80% of total pore volume coming from pores <20nm in radius. In 500 ppm constant voltage CDI tests, these fiber electrodes obtain a salt adsorption capacity of over 14 mg g -1 at a salt adsorption rate of ~4mg g -1 min -1 , showcasing the high capacity matched with high rate of these easily fabricated, inexpensive materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Electrospun Separator Based on Sulfonated Polyoxadiazole with Outstanding Thermal Stability and Electrochemical Properties for Lithium-Ion Batteries

Traditional polyolefin separators used in lithium-ion batteries (LIBs) are seriously limited by the issues of inferior security and poor electrolyte wettability. Most of the very promising candidate separators based on heat-resistant polymers are, however, inherently difficult to process. Herein, a unique sulfonated aromatic heterocyclic polymer, lithiated poly(diphenyl ether oxadiazole) sulfonate (Li-SPEOD), was synthesized through a simple one-pot method and further electrospun to act as a novel separator (es-Li-SPEOD) for LIBs. In this work, the prepared Li-SPEOD possesses a high degree of sulfonation with a high molecular weight (M w = 4.31 × 10 5 ). The es-Li-SPEOD separator exhibits excellent mechanical and fire-resistance properties and is able to maintain dimensional stability at a temperature of even up to 400 °C in air. The ionic conductivity (3.57 mS cm –1 ) and lithium-ion transference number (0.37) of the es-Li-SPEOD with an electrochemical stability window of 4.5 V vs Li + /Li can be improved by 382.4 and 32.1%, respectively, compared to those of Celgard-2500 in the LiPF 6 electrolyte. The enhanced rate capability and cycle performance of the LiFePO 4 –Li half-cell are therefore obtained. Moreover, the es-Li-SPEOD displays an outstanding dendrite-suppressing effect for the lithium metal anode. This research proves that the Li-SPEOD-based separator has a broad application perspective in next-generation lithium batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

Review—Electrospun Inorganic Solid-State Electrolyte Fibers for Battery Applications

Inorganic solid-state electrolytes (SSEs), especially Li 7 La 3 Zr 2 O 12 (LLZO), are promising candidates for all solid-state batteries. Generally, SSEs are synthesized by solid-state reactions at high temperatures. The high temperature required to synthesize useful polymorphs (e.g., cubic phase, in the case of LLZO) increases their production cost. To lower the synthesis temperature, several approaches, including doping and crystallite size control via sol-gel processes, have been explored. Recently, electrospinning was used to synthesize the inorganic SSE fibers to control the crystallite size and lower the calcination temperature. Several publications followed that investigated the properties of fibers and demonstrated the use of these fibers in inorganic-polymer composite SSEs. This paper presents a concise discussion of electrospinning, the parameters that control fiber morphology, the synthesis of inorganic SSE fibers, the effect of sintering conditions on the fiber morphology and composition, and the recent use of these fibers in making composite SSEs and other battery applications. Additionally, most of the discussion focuses on LLZO, but this paper also discusses applications of other types of electrospun inorganic electrolyte fibers, the challenges of using these fibers, and possible future directions in this research field.

25 ENERGY STORAGE↗
DOE OSTI2021

High-Performance Li-Ion Battery Anodes from Electrospun Nanoparticle/Conducting Polymer Nanofibers

The project objectives were: (1) Fabricate, characterize, and optimize the composition/morphology of an entirely new class of Si-based nanofiber anodes for Li-ion batteries, with high gravimetric and volumetric energy density and minimal capacity fade during charge/discharge cycling, (2) Improve our understanding of structure/functions correlations in electrospun particle/conducting polymer nanofiber anodes, and (3) Perform pilot-scale-up studies for anode commercialization.

25 ENERGY STORAGE↗
DOE OSTI2023

Bipolar Membranes with an Electrospun 3D Junction

Freestanding bipolar membranes (BPMs) with an entirely new and transformative morphology were fabricated and characterized. The key disruptive design element was a water-splitting/water-generation junction layer of finite thickness composed of interwoven and interlocking electrospun anion-exchange polymer (AEP) fibers and cation-exchange polymer (CEP) fibers. Methods were developed to sandwich the 3D junction layer between two pre-formed dense AEP and CEP films., with the closure of all interfiber voids, where the processing steps are easily incorporated into a commercial roll-to-roll membrane manufacturing scheme. A series of membranes were made using different polymers and junction layers to identify the optimum morphology and composition for water-splitting and water-generation applications. For water splitting, the 3D junction BPMs worked remarkably well with operating current densities at/above 1.0 A/cm2 (10X greater than commercial BPMs) at a transmembrane voltage drop of only 1.1 V. In water generation mode, the 3D junction BPMs operated at 0.5 A/cm2, a world-record current density. The membranes were found to exhibit outstanding durability and can be manufactured at scale for low cost. The high operating current densities and stable long-term operation are due to the 3D junction layer design, where there is a high interfacial area for water splitting or water generation reactions and where the interlocking fibers prevent delamination of the outer films. These new BPMs are ideal candidate materials for both existing water-splitting electrodialysis separations and new electrochemical processes, such as large-scale direct air capture of CO 2 , reactors for CO 2 reduction, self-hydrating fuel cells, and redox flow batteries.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Electrospun Hybrid Perfluorosulfonic Acid/Sulfonated Silica Composite Membranes

Electrospinning was employed to fabricate composite membranes containing perfluorosulfonic acid (PFSA) ionomer, poly(vinylidene fluoride) (PVDF) reinforcement and a sulfonated silica network, where the latter was incorporated either in the PFSA matrix or in the PVDF fibers. The best membrane, in terms of proton conductivity, was made by incorporating the sulfonated silica network in PFSA fibers (Type-A) while the lowest conductivity membrane was obtained when sulfonated silica was incorporated into the reinforcing PVDF fibers (Type-B). A Type-A membrane containing 65 wt.% PFSA with an embedded sulfonated silica network (at 15 wt.%) and with 20 wt.% PVDF reinforcing fibers proved superior to the pristine PFSA membrane in terms of both the proton conductivity in the 30–90% RH at 80 °C (a 25–35% increase) and lateral swelling (a 68% reduction). In addition, it was demonstrated that a Type-A membrane was superior to that of a neat 660 EW perfluoroimide acid (PFIA, from 3M Co.) films with respect to swelling and mechanical strength, while having a similar proton conductivity vs. relative humidity profile. This study demonstrates that an electrospun nanofiber composite membrane with a sulfonated silica network added to moderately low EW PFSA fibers is a viable alternative to an ultra-low EW fluorinated ionomer PEM, in terms of properties relevant to fuel cell applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Electrospun PVA Fibers for Drug Delivery: A Review

Innovation in biomedical science is always a field of interest for researchers. Drug delivery, being one of the key areas of biomedical science, has gained considerable significance. The utilization of simple yet effective techniques such as electrospinning has undergone significant development in the field of drug delivery. Various polymers such as PEG (polyethylene glycol), PLGA (Poly(lactic-co-glycolic acid)), PLA(Polylactic acid), and PCA (poly(methacrylate citric acid)) have been utilized to prepare electrospinning-based drug delivery systems (DDSs). Polyvinyl alcohol (PVA) has recently gained attention because of its biocompatibility, biodegradability, non-toxicity, and ideal mechanical properties as these are the key factors in developing DDSs. Moreover, it has shown promising results in developing DDSs individually and when combined with natural and synthetic polymers such as chitosan and polycaprolactone (PCL). Considering the outstanding properties of PVA, the aim of this review paper was therefore to summarize these recent advances by highlighting the potential of electrospun PVA for drug delivery systems.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Multifunctional Fibroblasts Enhanced via Thermal and Freeze-Drying Post-treatments of Aligned Electrospun Nanofiber Membranes

Parallel fibrous scaffolds play a critical role in controlling the morphology of cells to be more natural and biologically inspired. Among popular tissue engineering materials, poly(2-hydroxyethyl methacrylate) (pHEMA) has been widely investigated in conventional forms due to its biocompatibility, low toxicity, and hydrophilicity. However, the swelling of pHEMA in water remains a major concern. To address this issue, randomly oriented and aligned as-spun pHEMA nanofibrous scaffolds were first fabricated at speeds of 300 and 2000 rpm in this study, which were then post-treated using either a thermal or a freeze-drying method. In cell assays, human dermal fibroblasts (HDFs) adhered to the freeze-drying treated substrates at a significantly faster rate, whereas they had a higher cell growth rate on thermally-treated substrates. Results indicated that the structural properties of pHEMA nanofibrous scaffolds and subsequent cellular behaviors were largely dependent on post-treatment methods. Moreover, this study suggests that aligned pHEMA nanofibrous substrates tended to induce regular fibroblast orientation and unidirectionally oriented actin cytoskeletons over random pHEMA nanofibrous substrates. Such information has predictive power and provides insights into promising post-treatment methods for improving the properties of aligned pHEMA scaffolds for numerous tissue engineering applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Rare-earth-doped electrospun scheelite CaWO 4 nanofibers with excitation-dependent photoluminescence and high-linearity cathodoluminescence for ratiometric UV wavelength and radiation sensors

Scheelite structured AWO 4 compounds (A = Ba, Ca, Pb and Sr) are efficient hosts for rare-earth dopants. In this work, high-aspect-ratio AWO 4 (A = Ba, Ca, Pb and Sr) nanofibers, doped with 5 mol.% Tb and 5 mol.% Eu on A site, were synthesized using a sol-gel electrospinning technique, and their performances as a ratiometric sensor for the detection of UV light wavelength were comparatively studied. High-resolution electron microscopy reveals the presence of nanosized grains composing the nanofibers. The AWO 4 :5Tb-5Eu nanofibers exhibit strong characteristic photoluminescence (PL) and cathodoluminescence (CL) emission from both Tb 3+ and Eu 3+ ions. In the case of CaWO 4 lattice, the emission intensity ratio of Tb 3+ /Eu 3+ is found to show a linear relationship with the excitation wavelength in the tested range of 240–330 nm, with efficient energy transfer from host lattice to rare-earth ions. However, a similar result is not observed in other scheelite structured BaWO 4 , PbWO 4 , and SrWO 4 nanofibers. Here, the unique PL emission characteristics of CaWO 4 :5Tb-5Eu under different UV excitation wavelengths are due to its unique excitation band. This study reveals a potential new application of CaWO 4 :5Tb-5Eu as a fluorescent probe for UV wavelength detection. Additionally, the CL intensities from CaWO 4 :5Tb-5Eu nanofibers exhibit highly linear dependences on the applied voltage and current without saturation, which can be utilized for radiation detection.

36 MATERIALS SCIENCE↗