Search NASA⌕ Search

SEARCH · Search NASA

Results for “etch morphology”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Influence of Surface Treatment on the Interfacial and Mechanical Performance of Metal-Insert Overmolded Composites

Structural composites with metal inserts are gaining increasing interest enabling light weight design for energy efficiency, provide insulation, corrosion protection without compromising mechanical integrity. Such over molded metal-polymer composites show strong potential in many automotive and aerospace component parts, e.g. car bumper, chassis, door, brackets, fasteners, etc. Despite several advantages, metal-polymer dissimilar interface remains a weak spot in structural design, requiring further investigation to improve interfacial interlocking. The current work focuses on enhancing the metal-polymer adhesion between stainless steel inserts and polymer matrices (e.g. acrylonitrile butadiene styrene resin (ABS), and polyamide 66 (PA66) through surface treatment via chemical etching and mechanical roughening. In the chemical etching process, metal substrates were treated with aqua regia solution for different time intervals to evaluate surface roughness measured by water contact angle and morphology analysis. For mechanical roughening approach, metal inserts were subjected to blasting for surface abrasion. Treated samples were also functionalized with aminosilane coupling agent which showed successful grafting on the surface measured by water contact angle. Metal inserts with micro level surface roughness through etching exhibited significant 21% improvement in adhesion strength compared to untreated inserts; however, the effect of silane treatment on the interfacial strength was found to be highly matrix dependent.

Saha, Subhabrata [ORNL] (ORCID:000000033966064X)↗
DOE OSTI2024

Wet-Etching of Acoustically Spalled GaAs for Substrate Reuse

Acoustic spalling is a promising technique for substrate reuse in the fabrication of gallium arsenide (GaAs) photovoltaic cells. However, the acoustic spalling process can leave the substrate with areas of rough surface morphology that can interfere with subsequent cell growth and processing. In this work, we investigate the use of wet etchants to smooth the surface of acoustically spalled GaAs substrates. We evaluated six different etchants. Of those tested, an 8:1:1 mixture of sulfuric acid, hydrogen peroxide, and water at 30 degrees C and a moderate stirring rate showed the greatest roughness reduction per mass loss while producing the desired morphology. This etchant was then applied to an acoustically spalled 2-inch GaAs wafer. A single-junction GaAs cell was then grown via metalorganic vapor-phase epitaxy on this substrate, an acoustic spalled substrate without a smoothing etch, and an epi-ready substrate. Use of the 8:1:1 H2SO4:H2O2:H2O etchant produced cells an average efficiency of 12.8% as compared to that of 2.0% grown on the unetched acoustically spalled substrate and 16.3% grown on the epi-ready substrate. The results of this work demonstrate that wet etching is a viable method for smoothing the surface of spalled GaAs substrates, paving the way for substrate reuse via acoustic spalling at efficiencies that approach growth on epi-ready substrates.

etching↗
DOE OSTI2022

Twin-free, directly synthesized MFI nanosheets with improved thickness uniformity and their use in membrane fabrication

Zeolite nanosheets can be used for the fabrication of low-defect-density, thin, and oriented zeolite separation membranes. However, methods for manipulating their morphology are limited, hindering progress toward improved performance. We report the direct synthesis (i.e., without using exfoliation, etching, or other top-down processing) of thin, flat MFI nanosheets and demonstrate their use as high-performance membranes for xylene isomer separations. Our MFI nanosheets were synthesized using nanosheet fragments as seeds instead of the previously used MFI nanoparticles. The obtained MFI nanosheets exhibit improved thickness uniformity and are free of rotational and MEL intergrowths as shown by transmission electron microscopy (TEM) imaging. The nanosheets can form well-packed nanosheet coatings. Upon gel-free secondary growth, the obtained zeolite MFI membranes show high separation performance for xylene isomers at elevated temperature (e.g., p-xylene flux up to 1.5 × 10 –3 mol m –2 s –1 and p-/o-xylene separation factor of ~600 at 250°C).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Improving Performance of III-V Solar Cells Grown on Spalled Germanium with Ex Situ Substrate Planarization

Controlled spalling allows removal of devices and provides an opportunity for cost reduction through substrate reuse. However, the fracture-based process can leave behind morphological surface features, notably river lines, that can disrupt epitaxial growth and degrade device performance. We investigate the viability of various wet etch chemistries to planarize river lines to ensure high-quality device growth and performance without mechanical repolishing, and so maintain a route towards cost-effective reuse. Etching in a HF: HNO 3 :CH 3 COOH solution effectively planarizes river lines and produces a surface that yields devices with equivalent performance to those grown on epi-ready Ge wafer surfaces. Further studies will focus on optimizing etch composition, temperature, and time to minimize material removal while maintaining a suitable surface for high-quality epitaxy.

germanium↗
DOE OSTI2020

High-Performance Pt–Co Nanoframes for Fuel-Cell Electrocatalysis

Pt-based alloy catalysts are promising candidates for fuel-cell applications, especially for cathodic oxygen reduction reaction (ORR) and anodic methanol oxidation reaction (MOR). The rational design of composition and morphology is crucial to promoting catalytic performances. Here, we report the synthesis of Pt–Co nanoframes via chemical etching of Co from solid rhombic dodecahedra. The obtained Pt–Co nanoframes exhibit excellent ORR mass activity in acidic electrolyte, which is as high as 0.40 A mg Pt –1 initially and 0.34 A mg Pt –1 after 10 000 potential cycles at 0.95 V RHE . Furthermore, their MOR mass activity in alkaline media is up to 4.28 A mg Pt –1 and is 4-fold higher than that of commercial Pt/C catalyst. Furthermore, experimental studies indicate that the weakened binding of intermediate carbonaceous poison contributes to the enhanced MOR behavior. More impressively, the Pt–Co nanoframes also demonstrate remarkable stability under long-term testing, which could be attributed to the negligible electrochemical Co dissolution.

25 ENERGY STORAGE↗
DOE OSTI2022

On the Nature of Surface Defects Found in 2/0 N-Doped 9-Cell Cavities

In this contribution, we present a systematic study on the microstructure of 1.3 GHz 9-cell TESLA type SRF cavity, processed with 2/0 Nitrogen-doping surface treatment, to explain the premature quench phenomena commonly observed in N-doping treated cavities. The microstructure characterization was carried out using Secondary electron images, advanced metallurgical techniques such as EBSD in parallel with chemical information obtained from spectroscopic techniques. The most remarkable difference is observed in the ends-cavities (1 and 9), which showed roughening of the surface, revealing a series of morphologies associated with Nb cubic phase. The cell-to-cell analysis also showed standard features such as pits with different geometry and distribution, located in grains and grain boundaries. The defects found in this system suggest that the standard electropolishing chemical etching was insufficient to eliminate history defects produced during the manufacture of the cavity, without discarding the role of the impurities, N and O, that could have induced the growth of these morphologies.

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

Characterization of Engineered Pinholes in Dielectric Stacks of High-Performance Poly-Silicon Passivating Contacts

Passivating contact structures are expected to be implemented in > 50 % of industrially manufactured silicon photovoltaics produced over the next decade. One type of passivating contact utilizes a c-Si/dielectric/doped poly-Si layer stack. In cases where the dielectric layer/s are thick enough to impede tunneling of charge carriers, it was shown that disruptions (pinholes) in the dielectric are required to facilitate transport.[1] Pinholes in SiOx layers have typically been formed via high temperature annealing that allows localized breakup of this layer. This approach has drawbacks; 1) high temperature annealing increases cost and 2) pinhole formation is sensitive to both the SiOx thickness and wafer surface morphology making control of density and dimensions difficult. Recently, an alternative method of pinhole formation relying on metal assisted chemical etching (MACE) was shown to allow control over pinhole areal densities.[2] Such control is critical as both the density and dimensions of the pinholes determine saturation current density and contact resistivity. The contacts formed with the MACE process are known as polysilicon on locally etched oxide or PLEO and also result in low saturation current densities and low contact resistivity due to SiOx passivation and engineered pinhole enabled charge carrier transport, respectively. Photovoltaic devices with efficiencies greater than 20 % have recently been produced with these contacts, demonstrating the viability of contacts with engineered pinholes. Experimentally, preferential local collection of excess charge carriers has been observed and definitively connected to thermally induced pinholes in thick SiOx layers within c-Si/SiOx/poly-Si contact structures.[3] Recent work has shown that enhanced local collection of excess carriers can result from enhanced diffusion of dopants through pinholes in SiOx layers.[4] This study was restricted to simulation and characterization of poly-Si with the same dopant type as the c-Si substrates. In this work we focus our analysis on boron doped poly-Si with different stacks of dielectric layers (PLEO and PLENO where the N refers to a SiNy layer on top of the SiOx) on n-type crystalline silicon. This provides insight into how engineered pinholes affect charge collection across the p-n junction. Like previous observations of locally enhanced carrier transport through thermally induced pinholes, the EBIC images in Figure 1 shows that engineered pinholes in PLENO (1a) and PLEO (1b) also exhibit locally enhanced carrier transport at pinhole locations (bright spots in the images). We will also present detailed correlative nanoscale structural and chemical analysis using TEM imaging and EELS analysis with sample preparation guided by EBIC imaging. This allows us to connect the density and dimensions of engineered pinholes with charge carrier transport and measured photovoltaic device parameters. Our findings will accelerate the adoption of PLEO and PLENO contacts in industrially manufactured photovoltaic devices.

EBIC↗
DOE OSTI2023

High-Performance Passivating Contacts for Si PV Based on Engineered, Doped Nanopinholes through Dielectric Layers

We present a novel, industrially relevant method to fabricate high-performance poly-Si passivating contacts for Si PV. Passivating contacts based on SiOx/poly-Si layer stacks have been implemented in record-efficiency homojunction Si solar cells. In this technology, the carrier transport through a surface-passivating SiOx is enabled either by quantum-tunneling or nanopinholes. The doped poly-Si layer provides charge-carrier selectivity. Previously, the ISFH research group demonstrated a record 26.1% efficient Si homojunction cell, where transport pinholes in ~2 nm SiOx were produced by thermal breakdown at > 1000 degrees C, which is hard to control and is surface morphology-dependent. At room temperature, our new process uses electroless plating of Ag nanoparticles, followed by metal-assisted chemical etching. Nanogalvanic corrosion yields < 20 nm-wide nanopinholes in an insulating > 2 nm SiOx layer. The nanopinholes are filled by a heavily doped a-Si:H overlayer. We drive in the dopants into the Si wafer with subsequent high-temperature annealing. Preferential incorporation of dopants at pinhole locations results in nanoscale p+/n or n+/n junctions near the wafer interface. Each heavily-doped nanoscale pinhole junction collects and transports photogenerated carriers to the cell metal contacts. The density of the engineered nanopinholes can be tuned over a wide range which is critical for optimization of device performance. The same nanogalvanic corrosion principles can be applied to produce doped transport pinholes in well-passivating thick dielectric SiOx/SiNy stacks. Importantly, our process does not rely on thermal breakdown of the dielectric layers and can be applied to textured wafers resulting in Si solar cells with > 20% conversion efficiency.

dielectric layer↗
DOE OSTI2023

Durable and Low-Cost Fractal Structured Multifunctional Coatings for Next-Generation CSP

Fractal coatings on various low-cost and high-temperature metallic substrates such as SS316, SS347, In800H, In740H, In625, Haynes 230, etc. were fabricated employing our patented novel electrodeposition process at various deposition potentials and deposition times, as well as chemical etching. The best combination of the materials and processing conditions were co-optimized for the reliable and repeatable fabrication of the multifunctional coatings. Surface morphologies were examined using SEM and AFM, and fractal characterization was done using a 3D optical surface profiler. Fractal dimension was used to identify successful fabrication and material parameters. The mechanical durability of the coatings was evaluated using several standardized tests, such as sand abrasion (ASTM D968) and adhesion (ASTM D3359), to fully characterize and demonstrate the mechanical durability of the fabricated surfaces. HTF immersion tests on the fractal multifunctional coatings were conducted based on a modification of the ASTM D870, which is established for static water immersion testing. To calculate the corrosion rates and descaled weight loss of the samples subjected to thermal exposure for different time durations (100 h, 300 h, 500 h, and optionally 750 h) to estimate the corrosion rate. While protecting the substrates from corrosion is an important goal, an allied goals is also to examine the post-corrosion temperature stability and properties of the molten salts themselves due to the dissolution of the constituents of the alloys and the corrosion products from the coatings that cause “fouling” of the molten salts. Fouling characteristics of the different molten salt HTFs exposed to coated and uncoated substrates were investigated. Finally, considering a prototype molten salt/sCO2 heat exchanger, cost/performance model is developed to demonstrate that the coatings on low-cost alloys such as stainless steel provide lower levelized cost of heat exchanger compared to high nickel content Ha230.

14 SOLAR ENERGY↗
DOE OSTI2021

Performance of III–V Solar Cells Grown on Reformed Mesoporous Ge Templates

We demonstrate a solar cell on reformed porous Ge with an efficiency of 7.7%. We generate mesopores in (100) Ge by bipolar electrochemical etching and anneal them at high temperature. The pores coalesce deep in the structure rather than at the surface as desired, although resulting in coarse superficial morphology unsuitable for device growth. To combat this issue, we developed a surface treatment involving an HBr dip, annealing at 415 degrees C, and a postannealing ultrasonic De-ionized water dip to improve the surface structure, resulting in a smoother reformed surface on which we grow a GaInAs solar cell. The structure retains embedded pores after growth and the transitions between Ge and III-V layers are distinct. The solar cell fabricated using the improved coalescence has an efficiency of 4.5%. The efficiency improves to 7.7% by isolating the rest of the device from three limiting localized shunt areas. Protruding defects in the porous Ge and III-V layers still limit the performance, but this work establishes a step toward the technical viability of this exfoliation approach, showing decent efficiency if protruding defects can be removed or reduced.

14 SOLAR ENERGY↗
DOE OSTI2025

MXene-Derived Potassium-Preintercalated Bilayered Vanadium Oxide Nanostructures for Cathodes in Nonaqueous K-Ion Batteries

Bilayered vanadium oxides (BVOs) are promising cathode materials for beyond-Li-ion batteries due to their tunable chemistries and high theoretical capacities. However, the large size of beyond-Li + ions limits electrochemical cycling and rate capability of BVO electrodes. Recent reports of MXene-derived BVOs with nanoscale flower-like morphology have shown improved electrochemical stability at high rates up to 5C in nonaqueous lithium-ion batteries. Here, we report how morphological stabilization can lead to improved rate capability in potassium-ion batteries (PIBs) through the synthesis and electrochemical characterization of MXene-derived K-preintercalated BVOs (MD-KVOs), which were derived from two V 2 CT x precursor materials prepared using two different etching protocols. We show that the etching conditions affect the surface chemistry of the MXene, which plays a role in the MXene-to-oxide transformation process. MXene derived from a milder etchant transformed into a nanoflower MD-KVO with two-dimensional (2D) nanosheet petals (KVO-DMAE) while a more aggressive etchant produced a MXene that transformed into a MD-KVO with one-dimensional (1D) nanorod morphology (KVO-CMAE). Electrochemical cycling of the produced MD-KVOs after drying at 200 °C under vacuum (KVO-DMAE-200 and KVO-CMAE-200) in PIBs showed that electrochemical stability of MD-KVO at high rates improved through the morphological stabilization of 2D particles combined with the control of interlayer water and K + ion content. Structure refinement of KVO-DMAE-200 further corroborates the behavior observed during K + ion cycling, connecting structural and compositional characteristics to the improved rate capability. This work demonstrates how proper synthetic methodology can cause downstream effects in the control of structure, chemical composition, and morphology of nanostructured layered oxide materials, which is necessary for development of future materials for beyond-Li-ion battery technologies.

25 ENERGY STORAGE↗
DOE OSTI2022

Tailored Mesoporous Microspheres by Polymerization-Induced Microphase Separation in Suspension

We describe the preparation of block polymer beads by aqueous suspension polymerization to create poly(caprolactone) (PCL)-block-poly(styrene-co-divinylbenzene) beads that can be selectively etched under basic conditions to yield mesoporous polymer microspheres with uniform pore size. Polyvinylalcohol was used to stabilize the suspension polymerization in which styrene and divinylbenzene monomers were polymerized from a PCL macrochain transfer agent (macroCTA). The resulting polymerization-induced microphase separation process led to a nanostructured bicontinuous morphology. The particle size and pore size were independently tunable: the particle size was controlled by the stir rate of the suspension polymerization-yielding average diameters ranging from 60 to 300 μm-while the pore size was determined by the molar mass of the PCL block, with the mode pore diameters being 6 nm and 11 nm after etching beads made using 13 and 45 kg/mol PCL blocks, respectively. Based on nitrogen sorption measurements, the surface areas of the beads were ~300 m 2 /g when using a PCL macroCTA of 13 kg/mol. The beads were homogenous throughout on the micron length scale as determined by confocal Raman microscopy and lacked an impermeable skin layer as confirmed by scanning electron microscopy. Furthermore, the scalability of suspension polymerization allows for the simple synthesis of large quantities of thermoset microspheres with uniform pore size. We also demonstrate the ability to incorporate functional pore walls into the beads using multiblock precursor polymers. These functionalized mesoporous polymer beads show high affinity for ionic dyes in aqueous solutions (as a proof of principle) and remove dye from the solution at rates exceeding those of commercial ion-exchange resins. The developed procedure could be used to generate other functional surface chemistries with important applications in heterogeneous catalysis, chromatography, and water remediation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

GaAs solar cells grown on acoustically spalled GaAs substrates with 27% efficiency

Acoustic spalling presents a potentially low-cost reuse pathway for III–V epitaxial growth substrates via exfoliation of device layers with recovery and reuse of the substrate. However, surface features formed during spalling can reduce the performance of subsequently grown devices. Here, we develop an understanding of how the surface morphology of acoustically spalled substrates affects GaAs solar cell performance and develop strategies to mitigate these impacts. We demonstrate that minor planarization of the surface by wet chemical etching and/or epitaxial growth, or the redesign of the device structure to thicken critical layers, prevents performance degradation. Using these strategies, we demonstrate a 0.25 cm 2 single-junction GaAs device with 26.9% ± 0.2% photovoltaic conversion efficiency under the AM1.5G spectrum grown on an acoustically spalled substrate. These results enable the growth of high-performance III–V devices on non-traditional substrates with the potential for significantly reduced device costs.

14 SOLAR ENERGY↗
DOE OSTI2021

Morphology engineering of iridium electrodes via modifying titanium substrates with controllable pillar structures for highly efficient oxygen evolution reaction

Nowadays, Ti is the well-chosen anode substrate material for proton exchange membrane electrolyzer cells (PEMECs) and modifications of the substrate surfaces are essential for the fabrication of highly efficient electrodes. Herein, we introduce the morphology engineering of Ir/Ti electrodes with different acid treatments of hydrochloric acid (HCl) and oxalic acid (OA), and the comparative benefits of these two acid treatment methods are studied from the aspects of their impacts on the morphology, interfacial contact resistance (ICR), and oxygen evolution reaction (OER) performances of resultant electrodes. Notably, compared to the flat surface from OA treatment, Ti substrates with the pillar structure could be successfully achieved via HCl etching. Further, the HCl and the oxalic acid (OA) treatments would reduce the interfacial contact resistance (ICR) to 15.2% and 5.5% of the pristine Ti substrate at 1.38 MPa, respectively. By iridium electrodeposition on Ti substrates, Ir/Ti electrodes with different catalyst loadings are fabricated. With similar low-loadings of about 0.05 mgIr cm –2 , an Ir/Ti electrode with HCl treated substrate exhibits a lower overpotential of ~283 mV at 10 mA cm –2 current density than 305 mV from OA treatment, due to the boosted reaction areas from HCl treatment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Improvement of screen-printable metallization paste for low-cost silicon solar cells utilizing silver coated copper powders

This aims of this project were to develop low-cost screen-printable Ag|Cu metallization, as alternative to Ag paste, for contacting PERC solar cells with transparent emitter for high performance and reliability. The intended goal was to achieve 81% fill factor with a screen-printable Ag|Cu paste alternative. This was attempted through a three strand approach including Ag|Cu formulation by SVMT, production using cavitation technology by ACI and contact formation through the understanding of (i) the liquid phase sintering of the nano/macro particles of Ag|Cu to achieve bulk metal with very low series resistance, (ii) optimization of contact firing to avoid penetration of Cu into the silicon bulk, and finally (iii) proper analysis to quantify the contributions of each resistance component and keep the total series resistance at 0.2 Ω-cm2, which would result in high fill factor of 81% by UNC Charlotte. The objectives also involved i) the implementation of glass frit with Cu metal that will etch through the ARC for low contact resistance and adhesion, ii) development of Ag|Cu pastes with the optimized glass frit, iii) investigation of the impact of Cu particle size, morphology and loading on the gridline resistance, iv) narrow gridline screen designs along with narrow gridline prints, v) development of fast belt speeds of up to 375 inches per minute (ipm) sintering, and vi) stability study on Ag|Cu contact to high performance and reliability.

14 SOLAR ENERGY↗
DOE OSTI2020

Au-free low-temperature ohmic contacts for AlGaN/AlN/GaN heterostructures

We report Au-free, Ti/Al/Ta ohmic contact on the AlGaN/AlN/GaN heterostructure using low annealing temperature is studied in this paper. With SiCl 4 plasma treatment at the recess-etched contact region, a low contact resistance of 0.52 Ω mm and a low sheet resistance of 373 Ω/sq are achieved after annealing at 550 °C for 30 s. The low annealing temperature also leads to better surface morphology. Furthermore, AlGaN/AlN/GaN high-electron-mobility transistors (HEMTs) are fabricated with the 550 °C, 30 s annealed Ti/Al/Ta ohmic contacts, and a maximum transconductance of 123 mS/mm and a maximum drain current of 510 mA/mm are obtained for a gate length of 4 μm. Based on Silvaco's Atlas device simulation framework, a scaled-down device with a short gate length of 1 μm would produce a maximum drain current density of 815 mA/mm. It indicates that the direct current performance of the HEMTs with the ohmic metal proposed in this work is considerably better than that with Au-based ohmic contact.

42 ENGINEERING↗
DOE OSTI2025

Carboxylic acid induced restructuring of the Fe 3 O 4 (001) surface

The redox properties of Fe 3 O 4 surfaces are central to many catalytic processes and enable dynamic, reduction-induced morphological restructuring during reactions. Here, we investigate the structural changes of the Fe 3 O 4 (001) surface during the decomposition of formic and acetic acids using scanning tunneling microscopy, X-ray photoelectron spectroscopy, and density functional theory (DFT) calculations. Both acids readily deprotonate, forming ordered carboxylate overlayers on the surface. Product formation pathways involve the removal of lattice oxygen, resulting in extensive surface restructuring. For formic acid, only a modest level of surface oxygen removal (∼3%) is observed, resulting in elongated pits along the octahedral Fe rows and exhibiting an aspect ratio of ∼3. In contrast, acetic acid induces more extensive reduction, with the removal of ∼20% of surface oxygen, yielding significantly larger pits while maintaining a similar aspect ratio. Repeated exposure to acetic acid further enlarges the pits, indicating preferential etching at step edges. DFT calculations reveal a mechanistic sequence in which lattice oxygen removal destabilizes adjacent Fe atoms, promoting their migration into the bulk and subsequent pit propagation and step edge formation. Together, these findings provide atomistic insights into the coupling between carboxylic acid conversion and oxide surface restructuring, underscoring the strong interplay between redox chemistry and morphological changes on catalytically active Fe 3 O 4 surfaces.

Ortiz-Garcia, José J. [Pacific Northwest National ↗
DOE OSTI2022

TiO 2 Nanocoatings with Controllable Crystal Type and Nanoscale Topography on Zirconia Implants to Accelerate Bone Formation

In dentistry, zirconia implants have emerged as a promising alternative for replacing missing teeth due to their superior aesthetic performance and chemical stability. To improve the osseointegration of zirconia implants, modifying their surface with hierarchical micro/nanotopography and bioactive chemical composition are two effective ways. In this work, a microscale topography was prepared on a zirconia surface using hydrofluoric acid etching, and then a 50 nm TiO 2 nanocoating was deposited via atomic layer deposition (ALD). Subsequently, an annealing treatment was used to transform the TiO 2 from amorphous to anatase and simultaneously generate nanoscale topography. Various investigations into the coating surface morphology, topography, wettability, and chemical composition were carried out using scanning electron microscopy, white light interferometry, contact‐angle measurement, X‐ray diffraction, and X‐ray photoelectron spectroscopy. In addition, in vitro cytocompatibility and osteogenic potential performance of the coatings were evaluated by human bone marrow mesenchymal stem cells (hBMSCs), and in vivo osseointegration performance was assessed in a rat femoral condyle model. Moreover, the possible mechanism was also investigated. The deposition of TiO 2 film with/without annealing treatment did not alter the microscale roughness of the zirconia surface, whereas the nanotopography changed significantly after annealing. The in vitro studies revealed that the anatase TiO 2 coating with regular wavelike nanostructure could promote the adhesion and proliferation of osteoblasts and further improve the osteogenic potential in vitro and osseointegration in vivo. These positive effects may be caused by nanoscale topography via the canonical Wnt/ β ‐catenin pathway. The results suggest that using ALD in combination with annealing treatment to fabricate a nanotopographic TiO 2 coating is a promising way to improve the osteogenic properties of zirconia implants.

Li, Nan (ORCID:0000000255156737)↗