SEARCH · Search NASA

Results for “fdem”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

27 records · Page 2

All sources NASA NTRS DOE OSTI

DOE OSTI2020

Plate motion in sheared granular fault system

Plate motion near the fault gouge layer, and the elastic interplay between the gouge layer and the plate under stick-slip conditions, is key to understanding the dynamics of sheared granular fault systems. Here, a two-dimensional implementation of the combined finite-discrete element method (FDEM), which merges the finite element method (FEM) and the discrete element method (DEM), is used to explicitly simulate a sheared granular gouge fault system. In this work we focus on investigating the influence of normal load, driving shear velocity and plate stiffness on the velocities and displacements in the direction parallel to the shear direction (x-direction) measured at locations on the upper and lower plates just adjacent to the gouge. The simulations show that during slip phases the magnitudes of the measured velocities on the upper and lower plates are proportional to the normal load and may be inversely proportional to the square root of the plate's shear modulus. Whereas, the driving shear velocity does not show distinct influence on the measured velocities. Additionally, large slip velocities are generally associated with large macroscopic friction coefficient drops. For the models subjected to smaller normal loads, larger shear velocities and with stiffer shear plates, the same magnitude of slip velocity could cause a larger drop of macroscopic friction coefficient. During stick phases, the velocities of the upper and lower plates are respectively slightly greater and slightly smaller than half of the driving shear velocity and are both in the same direction of shear. The shear strain rate of the gouge is calculated from this velocity difference between the upper and lower plate during stick phases and thus the gouge effective shear modulus can be calculated. The results show that the gouge effective shear modulus increases proportionally with normal load, while the influence of shear velocity and plate stiffness on gouge effective shear modulus is minor. The simulations address the dynamics of a laboratory-scale fault gouge system and may aid in revealing the complexities of earthquake frictional dynamics.

58 GEOSCIENCES↗

DOE OSTI2021

Benchmarking numerical methods for impact and cratering applications

Large scale computational models are important for studying impact cratering events that are prevalent both on Earth and, more broadly, in this solar system. To address these problems, models must reliably account for both large length scales (e.g., kilometers) and relatively long time scales (hundreds of seconds). This work benchmarks two such approaches, a more traditional hydrodynamics approach and a finite-discrete element method (FDEM), for impact cratering applications. Both 2D and 3D results are discussed for two different impact velocities, 5 km/s and 20 km/s, striking normal to the target and, for 3D simulations, 45° from vertical. In addition, comparisons to previously published data are presented. Finally, differences in how these methods model damage are discussed. Ultimately, both approaches show successful modeling of several different impact scenarios.

58 GEOSCIENCES↗

DOE OSTI2023

Multiscale numerical investigation of ratchet growth damage effects in PBX 9502

This paper presents results of numerical experiments conducted on the high explosive PBX 9502 to investigate how recently observed grain-scale damage mechanisms of ratchet growth affect uniaxial compression measurements. Simulations are multiscale in the sense of directly resolving grains, pores, cracks, and grain-interfaces based upon scanning electron microscope (SEM) images of damaged and undamaged samples. The combined finite-discrete element method (FDEM) is utilized to resolve both grain-scale microfracture and elastoplastic deformation of solid grains. Pristine (undamaged) and damaged microstructures are compared in simulation of unconfined compression tests of the same material from the literature. Here, the simulation results show the observed microscale mechanisms of damage, specifically microfracture predominantly around and sometimes through grains and crack-associated pore growth, can well-explain the effective degradation of strength and stiffness observed in the laboratory measurements.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Scale bridging damage model for quasi-brittle metals informed with crack evolution statistics

Computationally efficient methods for bridging length scales, from highly resolved micro/meso-scale models that can explicitly model crack growth, to macro-scale continuum models that are more suitable for modeling large parts, have been of interest to researchers for decades. In this work, an improved brittle damage model is presented for the simulation of dynamic fracture in continuum scale quasi-brittle metal components. Crack evolution statistics, including the number, length, and orientation of individual cracks, are extracted from high-fidelity, finite discrete element method (FDEM) simulations and used to generate effective material moduli that reflect the material’s damaged state over time. This strategy allows for the retention of small-scale physical behaviors such as crack growth and coalescence in continuum scale hydrodynamic simulations. However, the high-fidelity simulations required to generate the crack statistics are computationally expensive. Thus, steps were taken to produce a flexible constitutive model to reduce the number of costly high-fidelity simulations needed to produce accurate results. A new stress based degradation criterion is introduced for the degradation of individual material zones. This allows for the development of a heterogeneous damage distribution within the bulk material. Then a flow stress model is added to the hydrodynamic simulation to account for plasticity in quasi-brittle materials. As a result, the effective moduli model can be applied to a larger range of materials. The effective moduli constitutive model is used to simulate beryllium flyer plate experiments. The results from the continuum scale simulations using statistics from a single high-fidelity simulation are found to be in excellent agreement with numerical and experimental velocity interferometer data. The same set of crack statistics are used to extrapolate the results of a higher rate flyer plate case using the effective moduli model. In conclusion, the extension of this model to higher rate cases shows promise for further reducing the number of costly high-fidelity simulations needed to generate crack statistics.

36 MATERIALS SCIENCE↗

DOE OSTI2021

IC reports (2021)

We requested HPC support to continue research on the seismic waves generated by impacts. We used the following codes: (1) the Hybrid Optimization Software Suite (HOSS), developed at LANL. HOSS is based on a combined Finite and Discrete Element Method (FDEM). New material models are developed for the sedimentary rocks. HOSS has been recently benchmarked to iSale and FLAG codes. SPECFEM3D is an open-source code developed since the last 90s. It won the Gordon Bell award for best performance in 2003, was finalist again in 2008 for a run at 0.16 petaflops on 149,784 cores on the ‘Jaguar’ Cray system at Oak Ridge National Laboratory. It also won the BULL Joseph Fourier supercomputing award in 2010.; SW4 is a 4th-order finite difference code developed at LLNL which is currently actively developed to handle complex 3D models and to be ported on future exascale platforms. We assessed our need to a total of 3.9M CPU-hrs for year 1 and and 3.1 M for year 2.

79 ASTRONOMY AND ASTROPHYSICS↗

NASA NTRS1988

Monitoring cure of composite resins using frequency dependent electromagnetic sensing techniques

A nondestructive in situ measurement technique has been developed for monitoring and measuring the cure processing properties of composite resins. Frequency dependent electromagnetic sensors (FDEMS) were used to directly measure resin viscosity during cure. The effects of the cure cycle and resin aging on the viscosity during cure were investigated using the sensor. Viscosity measurements obtained using the sensor are compared with the viscosities calculated by the Loos-Springer cure process model. Good overall agreement was obtained except for the aged resin samples.

Kranbuehl, D. E.↗

NASA NTRS1991

Characterization of and sensor-model verification and control of the properties of PMR-13 during processing

This study presents an in situ sensor and a process-simulation model developed for monitoring and controlling the cure process of PMR-15. The time-temperature dependence of the buildup in the molecular network structure, extent of reaction, viscosity, flow, and consolidation during the cure of PMR-15 are discussed. The relationship of the time-temperature cycle used during imidization to the length of the endcapped chains formed is examined. The relationship of the time-temperature cure-processing cycle to the reaction kinetics, viscosity, flow, and consolidation during crosslinking is analyzed using frequency-dependent electromagnetic sensors and the Loos processing model. Application of the FDEMS sensing technique and the process-simulation model for quality assurance processing and automated on-line control of cure is discussed.

Kranbuehl, D.↗

NASA NTRS1993

Textile composite processing science

A multi-dimensional model of the Resin Transfer Molding (RTM) process was developed for the prediction of the infiltration behavior of a resin into an anisotropic fiber preform. Frequency dependent electromagnetic sensing (FDEMS) was developed for in-situ monitoring of the RTM process. Flow visualization and mold filling experiments were conducted to verify sensor measurements and model predictions. Test results indicated good agreement between model predictions, sensor readings, and experimental data.

Loos, Alfred C.↗

DOE OSTI2020

Simulation of mixed-mode fracture using the combined finite–discrete element method

It has been shown experimentally that under mixed tensile and compressive stress states, a corresponding mixed-mode fracture will occur. Here, the formation of mixed-mode fractures is investigated using the combined finite–discrete element method. A series of simulations with confining pressures ranging from 7.5 to 150 MPa generate a spectrum of mixed-mode failure conditions. These stress states at failure span the transition from the tensile to compressive failure. The models reproduce previous experiments on Carrara marble using a dog-bone geometry, and a comparison shows good qualitative agreement with the experimental observations. This paper demonstrates that mixed-mode fracture can be captured via numerical simulations and identifies areas where further research is required to better understand mixed-mode fracture processes.

42 ENGINEERING↗