Search NASA⌕ Search

SEARCH · Search NASA

Results for “fibre reinforcement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Effect of moderate temperatures on compressive strength of ultra-high-performance concrete: A microstructural analysis

Highlights: • All coarse aggregates and steel fibres were surrounded by the binder. • X-ray diffraction is useful for explaining the increase in compressive strength with increasing temperature. • Rosenhahnite and/or quartz Dauphiné-twinned phases improved the compressive strength. • Polypropylene fibres prevented spalling and preserved the compressive strength. • Concrete with steel and polypropylene fibres did not exhibit spalling at 300 °C. Concrete with two types of steel fibres and a polypropylene fibre prevented spalling and preserved the compressive strength at 300 °C, which makes these concretes suitable for long-term applications up to 300 °C, such as for steam collectors or thermal energy storage systems. The compressive strength behaviour of three types of ultra-high-performance fibre-reinforced concrete manufactured with the same matrix was investigated. For this purpose, a complete characterisation of all the raw materials and the three types of fibres used was performed. The morphology of all concrete mixtures at room temperature was analysed using scanning electron microscopy–energy-dispersive X-ray spectroscopy. From the results, it was ascertained that the steel fibres and coarse siliceous aggregates were not in contact (being separated by ≥3.41 μm) and were surrounded by the binder (of ≥1 μm in thickness) for all the mixtures studied. Rosenhahnite and/or quartz Dauphiné-twinned phases improved the compressive strength (as determined by X-ray diffraction).

36 MATERIALS SCIENCE↗
DOE OSTI2021

Monitoring steel fibre orientation in self-compacting cementitious composite slabs during pouring with dynamic X-ray radiography

This paper presents a new technique based on dynamic X-ray radiography that can be used to assess fibre orientation during pouring of steel fibre reinforced cementitious composites. Synthetic examples were used to assess the suitability and robustness of the technique, which was shown to provide reliable measurements of fibre orientation even when the signal-to-noise ratio is relatively high. A study was then carried out on the effect of formwork aspect ratio, time/duration of pouring, and rebar placement on the fibre orientation while pouring self-compacting cementitious composite slabs. Results demonstrated the ability of the technique in monitoring the movements of fibres while pouring, and the strong effect of the flow in inducing preferential fibre alignment within the slabs. Fibre orientation was found to vary progressively over time and could take about half of the duration of pouring to fully stabilise.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Simplifying the creation of thermal decomposition mechanisms for designing mixed fibre composites

Among the most challenging aspects of simulating thermal decomposition of fibre reinforced polymers is the determination of appropriate reaction parameters. Thermogravimetric analysis is typically used to generate decomposition data, to which the reaction parameters are then fit. When designing mixed fibre materials (e.g. combinations of glass and carbon fibres), the number of TGA experiments needed to explore the entire design space may be intractable. Here, we demonstrate the creation of two candidate proxy mixed fibre mechanisms and compare them to a mechanism created by fitting parameters from TGA on the mixed fibre composite. These mechanisms are then demonstrated in a 2D axisymmetric numerical decomposition, heat transfer, and porous flow model. We find a maximum 11% uncertainty in mass and 4% in temperature difference when using a proxy mechanism.

Scott, Sarah N. [Sandia National Lab. (SNL-CA), Li↗
DOE OSTI2021

Composites and additive manufacturing for high-field coil supports for stellarators

The utilization of composites layered on an additive manufactured substrate, for the production of coil supports for modular coils in small or middle size experimental stellarators is assessed. The focus of the study is a monolithic coil support comprising the coils of a half-period of a stellarator, somewhat similar to the ones in UST_2 and ARIES-CS stellarators. However, the concept may be applicable to quasi-monolithic coil supports (coil forms of NCSX type) or individual coil casings (W7-X type).Coil supports for stellarators require high precision, stiffness and strength for large contorted parts. Traditionally, monolithic coil supports are produced by steel casting/forging and final machining. This production method and material gives accurate, stiff and strong coil supports, but the method may be expensive for monolithic supports due to the geometrical complexity and required accuracy of the structure. In relation to those matters, this work investigates whether a monolithic coil support comprising an additive manufactured resin substrate, which is externally (outward from the coils) surrounded with a thick layer of fibre-reinforced resin, may achieve enough strength and stiffness under middle/high magnetic fields. Finite element calculations are produced to obtain the direction of the principal stresses and their values in compression and tension at different areas of the monolithic support, which is relevant for anisotropic materials. The feasibility of directional application of (carbon) fibres on the winding surface of the stellarator outward from the coils is experimentally tested on a scaled-down additively manufactured prototype of a monolithic support. The strength and stiffness of the composite structure appears sufficient for common magnetic fields in experimental stellarators, and the 3D-composite design and manufacturing was technically feasible.

Queral, Vicente↗
DOE OSTI2023

In situ high-temperature 3D imaging of the damage evolution in a SiC nuclear fuel cladding material

Silicon carbide (SiC)-based nuclear fission fuel rod cladding has been considered as one of the possible designs for accident tolerant fuels. It is in the form of a SiC fibre reinforced SiC matrix composite tube (SiC f -SiC m ) with monolithic SiC outer and/or inner coating layers. This study focuses on the deformation and fracture processes in this material using in situ X-ray micro-computed tomography (XCT) at room temperature (RT) and 1200 °C in an inert gas environment in a C-ring compression loading configuration. Prior to testing, local properties and residual stresses were characterised using nanoindentation and Raman spectroscopy since they can impact the mechanical behaviour of the material. The 3D strain distribution, crack formation and propagation processes including the toughening mechanisms (e.g., crack deflection, micro-cracking, crack bridging and bifurcation) are investigated in the coating and underlying composites at RT and 1200 °C. There is no particular sequence which toughening mechanism occurs first – this is very different from the conventional toughening theory in ceramic-matrix composites under uniaxial tension loading. Indeed, no evidence of fibre pull-out or fibre fracture was observed in this SiC f -SiC m nuclear cladding material in the current C-ring compression configuration. The correlation between local measurements and bulk mechanical behaviour are discussed.

3D imaging↗
DOE OSTI2025

Improved damage tolerance of SiC-based nuclear fuel cladding with novel multi-layered SiC coating design at 1200 °C

Continuous SiC fibre reinforced SiC matrix composites (SiC f -SiC m ) with monolithic SiC outer coatings are considered as a damage-tolerant cladding design for loss of coolant accident (LOCA) conditions in light water reactors. However, monolithic SiC coatings are brittle and prone to catastrophic failure. In this study, a SiC f -SiC m cladding with a novel multi-layer SiC outer coating (11 sub-layers, ∼260 µm in total thickness) was investigated under C-ring compression at room temperature and 1200 °C in argon environment. Real-time synchrotron X-ray computed tomography (XCT) was employed to capture crack initiation and propagation processes. Compared to conventional monolithic SiC outer coatings, the multi-layer coating structure facilitated crack deflection and bifurcation enhancing its damage tolerance at both temperatures. Despite pre-existing surface cracks, claddings exhibited stable mechanical-performance at both temperatures. These initial cracks did not critically affect the failure processes as they were not aligned with the maximum stress direction. Furthermore, the microstructure, distribution of residual stresses, and local properties of individual components in the material were thoroughly characterized, and compared with open literature on conventional claddings with monolithic outer coatings. These results provide new insights into the failure mechanisms of multi-layer SiC coatings and offer guidance for the future design of accident-tolerant nuclear fuel claddings.

36 - MATERIALS SCIENCE↗
DOE OSTI2026

Chain entanglements enable regeneration of high-performance thermosets

Thermoset plastics underpin structural materials, electronics and transportation, yet the permanent covalent networks that prevent flow and provide dimensional stability also make them difficult to recycle without sacrificing performance. In this work we show that high-performance thermosets can be built around dense chain entanglements, the physical interlacing of long polymer strands, rather than dense permanent crosslinks, with only a small number of selectively cleavable junctions preserving connectivity. Long, rigid, entangled polyolefin backbones generated by frontal polymerization form glassy polymers with high stiffness, high toughness and excellent creep suppression yet can be fully deconstructed into soluble, linear oligomers. Varying oligomer length and end-group chemistry enables their reuse as re-entangling building blocks that regenerate thermosets with thermal and mechanical properties that remain unchanged across generations. The strategy further extends to high-temperature fibre-reinforced composite matrices and additively manufactured structures, establishing chain entanglement as a design principle for durable, regenerable thermosets.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Sulphate resistance of low‐clinker engineered cementitious composites examined by MicroXRF imaging

Abstract Engineered cementitious composites (ECC) are a class of high‐performing fibre‐reinforced cementitious materials recognised for their increased ductility and durability compared to conventional cement‐based materials, owing to their autogenously controlled tight crack widths, even when subjected to high strains. To reduce ECC's environmental impact, this research examines the use of a low‐clinker binder − limestone‐calcined clay cement (LC3) − as an alternative to portland cement (PC), along with fly ash to further reduce the clinker proportion and the embodied CO 2 of the formulations. In conventional concrete, LC3 hydrates to a denser microstructure resulting from the synergistic reaction between limestone and calcined clay. At the lower water contents typical of ECC and with the presence of fly ash, the influence of the binder composition on the microstructure is difficult to anticipate. To examine the influence of these compositional variables on microstructure, permeability and durability, the sulphate resistance of LC3‐based ECC is explored. Specifically, the ECC‐LC3 blends are designed with high clinker replacement rate of 75% by mass of binder and contain either conventional fly ash or reclaimed fly ash at 50% by mass of binder. Expansion of ECC‐LC3 samples subjected to standard sodium sulphate test conditions was measured up to 12 months and the depth of penetration of sulphates into the ECC‐LC3 of varying compositions was quantified using micro‐X‐Ray Fluorescence (microXRF) imaging and modelling. The expansion results show that the ECC‐LC3 formulations performed better than the PC samples and can provide adequate resistance to external sulphate attack, even when reclaimed fly ashes are used in place of the conventional ash. In addition, the shallow penetration of sulphate into these cementitious composites demonstrates the low diffusion coefficients values that were determined using the quantitative data from MicroXRF imaging.

Microscopy↗
NASA NTRS1989

Steerable windowed enclosures

A gyro-stabilized mechanism that is to be carried on a vehicle, such as a helicopter, is provided with a protective enclosure consisting of a dome, usually of glass fibre reinforced plastic. The dome must be provided with a window transparent to the radiation involved, and this must be steered with the mechanism so that they remain in register with one another. Prior art structures employ elongated windows of sufficiently large size to accommodate the tilting and rolling of the mechanism, while pan movements are accommodated by rotating the entire dome. The invention provides a structure employing a small window that can be steered or slaved with the mechanism by rotation of the part of the dome including the window relative to the other part, which has the pan or yaw rotation motor connected to it. This rotation between the dome parts takes place in a skew plane disposed at as small a skew angle to the vertical as is possible, the compensation for the resulting transverse movement of the window being effected by a programmed rotation of the dome about the pan axis. Optically flat glass can then be used for the window, it can be coated to reduce reflections, etc, and it can also be wiped in operation to remove moisture. A broadcast antenna can be mounted on the part of the dome out of the line-of-sight of the apparatus.

John N Leavitt↗
NASA NTRS2009

Performance of "Waterless Concrete"

Waterless concrete consists of molten elementary sulfur and aggregate. The aggregates in a lunar environment will be lunar rocks and soil. Sulfur is present on the Moon in Troilite soil (FeS) and, by oxidation of the soil, iron and sulfur can be produced. Sulfur concrete specimens were cycled between liquid nitrogen (approx.]91 C) and room temperature (^21 C) to simulate exposure to a lunar environment. Cycled and control specimens were subsequently tested in compression at room temperatures (^21 C) and ^-101 C. Test results showed that due to temperature cycling, the compressive strength of cycled specimens was 20% of those non-cycled. This reduction in strength can be attributed to the large differences in thermal coefficients of expansion of the materials constituting the concrete which promoted cracking. Similar sulfur concrete mixtures were strengthened with short and long glass fibres. The lunar regolith simulant was melted in a 25 cc Pt- Rh crucible in a Sybron Thermoline high temperature MoSi2 furnace at melting temperatures of 1450 to 1600 C for times of 30 min to i hour. Glass fibres and small rods were pulled from the melt. The glass fibres were used to reinforce sulfur concrete plated to improve the flexural strength of the sulfur concrete. Beams strengthened with glass fibres showed to exhibit an increase in the flexural strength by as much as 45%.

Toutanji, H. A.↗
DOE OSTI2021

Substitution of virgin carbon fiber with low-cost recycled fiber in automotive grade injection molding polyamide 66 for equivalent composite mechanical performance with improved sustainability

Recycled carbon fiber has historically proven challenging to integrate into composite manufacturing due in no small part to the low-density, randomly oriented, discontinuous fiber format that results from typical recycling. Discontinuous fiber requires the use of alternative technologies than those traditionally applied to continuous fiber (e.g., hand lay-up, winding). Extrusion compounding is one such applicable technology, but material transfer into the system requires alternative feeding equipment or the use of an altered procedure as trialed in this research. In this study, an injection molding compound for automotive applications was prepared with recycled carbon fiber and compared against an existing commercial compound. Input fibers and molded compound were evaluated for mechanical performance, while relevant variables such as compounded fiber alignment and aspect ratio were compared to the existing baseline material to confirm a like-for-like composite material structure. Overall, analysis indicates that recycled fiber performs similarly to virgin fiber reinforcement, demonstrating that recycled fiber may be a viable drop-in replacement for short-fiber discontinuous applications.

42 ENGINEERING↗
NASA NTRS1988

SEM/XPS analysis of fractured adhesively bonded graphite fibre surface resin-rich/graphite fibre composites

Samples of graphite fiber-reinforced polyimide were fabricated allowing the resin to accumulate at the composite surface. These surface resin-rich composites were then bonded together and tested for lap shear strength both before and after thermal aging. Lap shear strength did not appear to show a significant improvement over that previously recorded for resin-poor samples and was shown to decrease with increasing aging time and temperature.

Devilbiss, T. A.↗
NASA NTRS1991

Effective thermal conductivity of composites with fibre-matrix debonding

Debonding of the fiber-matrix interface is a major cause for the degradation of the mechanical properties and the loss of thermal conductivity of fiber-reinforced composites. This paper discusses two analytical approaches for modeling the thermal conduction problem of composites. One is based on the concept of modeling the thermal barrier by an equivalent heat transfer coefficient at the fiber-matrix interface, as described by Hasselman and Johnson (1987) and Benveniste and Miloh (1986). The other approach, suggested by Hatta and Taya (1986), is by treating a composite with debonded interface as a coated-fiber composite. The major advantage of the latter aproach is that the thickness of the fiber coating can be realistically modeled depending upon the extent of degradation of the composite with the thermal conductivity of the coating as that of air.

Fadale, T. D.↗
NASA NTRS1981

Micro-area Auger analysis of a SiC/Ti fibre composite

Micro-area Auger electron spectroscopy with a spatial resolution of less than 50 nm has been used to study the concentration of elements across the reaction zone of a W-reinforced SiC fiber in a titanium matrix. Although the elemental concentrations obtained by this technique are affected by the reaction zone morphology to a greater extent than in the case of X-ray microprobe analysis, the proposed technique has the advantage of a much higher spatial resolution and avoids the problems of bulk averaging that characterize the X-ray technique.

Zironi, E. P.↗
NASA NTRS1989

Investigation of interfacial shear strength in a SiC fibre/Ti-24Al-11Nb composite by a fibre push-out technique

A fiber push-out technique applied at several sample thicknesses was used to determine both the debond shear stress and the frictional shear stress at the fiber-matrix interface at room temperautre for a unidirectional SiC fiber-reinforced T-24Al-11Nb (in at. pct) composite prepared by a powder cloth technique. The push-out technique measures the separate contributions of bond strength and friction to the mechanical shear strength at the fiber-matrix interface. It was found that the fiber-matrix bond shear strength of this material is significantly higher than the fiber-matrix frictional shear stress (119.2 and 47.8 MPa, respectively).

Eldridge, J. I.↗
NASA NTRS1988

Fibre-matrix bond strength studies of glass, ceramic, and metal matrix composites

An indentation test technique for compressively loading the ends of individual fibers to produce debonding has been applied to metal, glass, and glass-ceramic matrix composites; bond strength values at debond initiation are calculated using a finite-element model. Results are correlated with composite longitudinal and interlaminar shear behavior for carbon and Nicalon fiber-reinforced glasses and glass-ceramics including the effects of matrix modifications, processing conditions, and high-temperature oxidation embrittlement. The data indicate that significant bonding to improve off-axis and shear properties can be tolerated before the longitudinal behavior becomes brittle. Residual stress and other mechanical bonding effects are important, but improved analyses and multiaxial interfacial failure criteria are needed to adequately interpret bond strength data in terms of composite performance.

Grande, D. H.↗
DOE OSTI2021

Development of a compressive failure model for carbon fiber composites and associated uncertainties.

An approach to increase the value of carbon fiber for wind turbines blades, and other compressive strength driven designs, is to identify pathways to increase its cost-specific compressive strength. A finite element model has been developed to evaluate the predictiveness of current finite element methods and to lay groundwork for future studies that focus on improving the cost-specific compressive strength. Parametric studies are conducted to understand which uncertainties in the model inputs have the greatest impact on compressive strength predictions. Furthermore, a statistical approach is also presented that enables the micromechanical model, which is deterministic, to efficiently account for statistical variability in the fiber misalignment present in composite materials; especially if the results from the hexagonal and square pack models are averaged. The model was found to agree well with experimental results for a Zoltek PX-35 pultrusion. The sensitivity studies suggest that the fiber packing and the interface shear strength have the greatest impact on compressive strength prediction for the fiber reinforced polymer studied here. Based on the performance of the modeling approach presented in this work, it is deemed sufficient for future work which will seek to identify carbon fiber composites with improved cost-specific compressive strength.

36 MATERIALS SCIENCE↗