Search NASA⌕ Search

SEARCH · Search NASA

Results for “flaps”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

Reduction of Flap Side Edge Noise - the Blowing Flap

A technique to reduce the noise radiating from a wing-flap side edge is being developed. As an airplane wing with an extended flap is exposed to a subsonic airflow, air is blown outward through thin rectangular chord-wise slots at various locations along the side edges and side surface of the flap to weaken and push away the vortices that originate in that region of the flap and are responsible for important noise emissions. Air is blown through the slots at up to twice the local flow velocity. The blowing is done using one or multiple slots, where a slot is located along the top, bottom or side surface of the flap along the side edge, or also along the intersection of the bottom (or top) and side surfaces.

Hutcheson, Florence V.↗
NASA NTRS1944

Wind Tunnel Investigation of the Effects of Slot Shape and Flap Location on the Characteristics of a Low-Drag Airfoil Equipped with a 0.25-Chord Slotted Flap

Tests were conducted at dynamic pressure of 50 lb per square foot with lift drag and pitch moment measurements throughout useful angle of attack range for constant flap deflection and position of a low-drag airfoil. Two slots were investigated and practical flap paths were selected for each Slot shape had a negligible effect on the maximum lift coefficient flap deflected, the rounded-entry slot had lower profile drag.

WIND TUNNEL TESTS - AAL - (10'X 7')↗
NASA NTRS1973

Effect of wing aspect ratio and flap span on aerodynamic characteristics of an externally blown jet-flap STOL model

An investigation has been conducted to determine the effects of flap span and wing aspect ratio on the static longitudinal aerodynamic characteristics and chordwise and spanwise pressure distributions on the wing and trailing-edge flap of a straight-wing STOL model having an externally blown jet flap without vertical and horizontal tail surfaces. The force tests were made over an angle-of-attack range for several thrust coefficients and two flap deflections. The pressure data are presented as tabulated and plotted chordwise pressure-distribution coefficients for angles of attack of 1 and 16. Pressure-distribution measurements were made at several spanwise stations.

Smith, C. C., Jr.↗
NASA NTRS1976

Noise reduction tests of large-scale-model externally blown flap using trailing-edge blowing and partial flap slot covering

Noise data were obtained with a large-scale cold-flow model of a two-flap, under-the-wing, externally blown flap proposed for use on future STOL aircraft. The noise suppression effectiveness of locating a slot conical nozzle at the trailing edge of the second flap and of applying partial covers to the slots between the wing and flaps was evaluated. Overall-sound-pressure-level reductions of 5 db occurred below the wing in the flyover plane. Existing models of several noise sources were applied to the test results. The resulting analytical relation compares favorably with the test data. The noise source mechanisms were analyzed and are discussed.

Mckinzie, D. J., Jr.↗
NASA NTRS1976

The Effects of Blowing Over Various Trailing-edge Flaps on an NACA 0006 Airfoil Section, Comparisons with Various Types of Flaps on other Airfoil Sections, and an Analysis of Flow and Power Relationships for Blowing Systems

The results are presented of a two-dimensional investigation conducted to determine the effect of blowing over various types of trailing-edge flaps on a wing having the NACA 0006 airfoil section and a drooped-nose flap. The position and profile of the trailing-edge flap, the nozzle height, and the location of the flap with respect to the nozzle were found to be important variables. Data from many investigations were used to make an evaluation of the effects of blowing on lift. An analysis was made of flow and power relationships for blowing systems.

Dods, J. B., Jr.↗
NASA NTRS1986

An experimental investigation of the aerodynamics of a NACA 64A010 airfoil-flap combination with and without flap oscillations. Part 1: Steady-state characteristics

A NACA 64A010 airfoil with a sealed-gap 1/4-chord flap was tested between splitter plates in the NASA Ames 11- by 11-Foot Transonic Wind Tunnel at Mach numbers from 0.50 to 0.85, and Reynolds numbers based on chord from 3 to 13 million. Although the main purpose of the test was to obtain unsteady pressure data with the flap oscillating, no unsteady data are presented in this paper. The steady-state data are presented and compared with other test data to provide a basis for evaluating the results. Pressure data at two span stations are used to deduce early boundary-layer transitions at the midspan at higher Mach numbers, angles of attack, and flap angles. The effects of flap angle on pressures, normal force, pitching moment, and hinge moment are also presented in the report. Mach number errors caused by the splitter-plate configuration and the angle of attack are evaluated using pressure measurements near the floor and ceiling of the wind tunnel.

Buell, Donald A.↗
NASA NTRS1958

Effectiveness of Boundary-layer Control, Obtained by Blowing over a Plain Rear Flap in Combination with a Forward Slotted Flap, in Deflecting a Slipstream Downward for Vertical Take-off

The wing employed in this investigation had a 67-percent-chord slotted flap in combination with a 33-percent-chord plain rear flap equipped with a full-span blowing nozzle. The tests were conducted in a static-thrust facility at the Langley Aeronautical Laboratory. The investigation indicated that the plain rear flap alone with a low momentum coefficient for boundary-layer control provided larger turning angles than the combined slotted and plain flaps without boundary-layer control.

HIGH-LIFT DEVICES - COMPLETE WINGS↗
NASA NTRS1947

Two-Dimensional Wind-Tunnel Investigation of Modified NACA 65(112)-111 Airfoil with 35-Percent-Chord Slotted Flap to Determine Optimum Flap Configuration at Reynolds Number of 2.4 Million

An investigation has been made in the Langley two-dimensional low-turbulence tunnel to develop the optimum configuration of a 0.35-chord slotted flap on an NACA 65 (112)-111 airfoil section modified by removing the trailing-edge cusp. The results of the investigation indicate that for the optimum configuration at a Reynolds number of 2.4 x 10(exp 6), the flap deflection was 45 degrees and the flap leading-edge radius center was 0.73 percent-chord behind and 4.46 percent-chord below the slot lip. The maximum section lift coefficient for the optimum configuration at a Reynolds number of 2.4 x 10(exp 6) was 2.46 or 0.12 higher than that obtained for an NACA 65-210 airfoil section with a 0.250-chord slotted flap.

Racisz, Stanley F.↗
NASA NTRS1976

Calculation of the longitudinal aerodynamic characteristics of wing-flap configurations with externally blown flaps

An analytical method for predicting the longitudinal aerodynamic characteristics of externally blown flap configurations is described. Two potential flow models make up the prediction method: a wing and flap lifting-surface model and a turbofan engine wake model. A vortex-lattice lifting-surface method is used to represent the wing and multiple-slotted trailing-edge flaps. The jet wake is represented by a series of closely spaced vortex rings normal to a centerline which is free to move to conform to the local flow field. The two potential models are combined in an iterative fashion to predict the jet wake interference effects on a typical EBF configuration. Comparisons of measured and predicted span-load distributions, individual surface forces, forces and moments on the complete configuration, and flow fields are included.

Mendenhall, M. R.↗
NASA NTRS1957

Investigation of Effectiveness of a Wing Equipped with a 50-percent-chord Sliding Flap, a 30-percent-chord Slotted Flap, and a 30-percent-chord Slat in Deflecting Propeller Slipstreams Downward for Vertical Take-off

Results are presented of an investigation of the effectiveness of a wing equipped with a 50-percent-chord sliding flap and a 30-percent-chord slotted flap in deflecting a propeller slipstream downward for vertical take-off. Tests were conducted at zero forward speed in a large room and included the effects of flap deflection, proximity to the ground, a leading-edge slat, and end plates. A turning angle of about 70 degrees and a resultant force of about 100 percent of the thrust were achieved near the ground. Out of the ground-effect region, the turning angle was also about 70 degrees but the resultant force was reduced to about 86 percent of the thrust.

AIRPLANES - PERFROMANCE↗
NASA NTRS1936

Aerodynamic characteristics of wings with cambered external airfoil flaps, including lateral control, with a full-span flap

The results of a wind-tunnel investigation of the NACA 23012, the NACA 23021, and the Clark Y airfoils, each equipped with a cambered external-airfoil flap, are presented in this report. The purpose of the research was to determine the relative merit of the various airfoils in combination with the cambered flap and to investigate the use of the flap as a combined lateral-control and high-lift device.

Platt, Robert C↗
NASA NTRS2014

Blended Cutout Flap for Reduction of Jet-Flap Interaction Noise

An aircraft system includes a wing and a trailing edge device coupled to the wing. The trailing edge device is movable relative to the wing, and includes a leading edge and a trailing edge having a center flap portion and a plurality of outer edge portions integrally combined with the center flap portion such that the center flap portion is shorter in width than that of outer edge portions.

Czech, Michael J↗
NASA NTRS1974

Aerodynamics of jet flap and rotating cylinder flap STOL concepts

The aerodynamic effectiveness of various propulsive lift concepts to provide for the low speed performance and control required for short takeoff and landing aircraft is discussed. The importance of the interrelationship between the propulsion system and aerodynamic components of the aircraft is stressed. The relative effectiveness of different lift concepts was evaluated through static and wind tunnel tests of various aerodynamic models and propulsion components, simulations of aircraft, and in some cases, flight testing of research aircraft incorporating the concepts under study. Results of large scale tests of lift augmentation devices are presented. The results of flight tests of STOL research aircraft with augmented jet flaps and rotating cylinder flaps are presented to show the steeper approach flight paths at low forward speeds.

Cook, W. L.↗
NASA NTRS1982

Aeroacoustic performance of an externally blown flap configuration with several flap noise suppression devices

Small scale model acoustic experiments were conducted to measure the noise produced in the flyover and sideline planes by an engine under the wing externally blown flap configuration in its approach attitude. Broadband low frequency noise reductions as large as 9 dB were produced by reducing the separation distance between the nozzle exhaust plane and the flaps. Experiments were also conducted to determine the noise suppression effectiveness in comparison with a reference configuration of three passive types of devices that were located on the jet impingement surfaces of the reference configuration. These devices produced noise reductions that varied up to 10 dB at reduced separation distances. In addition, a qualitative estimate of the noise suppression characteristics of the separate devices was made. Finally static aerodynamic performance data were obtained to evaluate the penalties incurred by these suppression devices. The test results suggest that further parametric studies are required in order to understand more fully the noise mechanisms that are affected by the suppression devices used.

Mckinzie, D. J., Jr.↗
NASA NTRS1993

Internal performance of a nonaxisymmetric nozzle with a rotating upper flap and a center-pivoted lower flap

An investigation was conducted at wind-off conditions in the static-test facility of the Langley 16-Foot Transonic Tunnel to determine the internal performance characteristics of a single expansion-ramp nozzle with thrust-vectoring capability to 105 degrees. Thrust vectoring was accomplished by the downward rotation of an upper flap with adaptive capability for internal contouring and a corresponding rotation of a center-pivoted lower flap. The static internal performance of configurations with pitch thrust-vector angles of 0 degrees, 60 degrees, and 105 degrees each with two throat areas, was investigated. The nozzle pressure ratio was varied from 1.5 to approximately 8.0 (5.0 for the maximum throat area configurations). Results of this study indicated that the nozzle configuration of the present investigation, when vectored, provided excellent flow-turning capability with relatively high levels of internal performance. In all cases, the thrust vector angle was a function of the nozzle pressure ratio. This result is expected because the flow is bounded by a single expansion surface on both vectored- and unvectored-nozzle geometries.

Wing, David J.↗