Search NASA⌕ Search

SEARCH · Search NASA

Results for “flow augmentation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1960

Low-Speed Investigation of a Full-Span Internal-Flow Jet-Augmented Flap on a High-Wing Model with a 35 deg Swept Wing of Aspect Ratio 7.0

An investigation of a full-span 17-percent-chord internal-flow jet-augmented flap on an aspect-ratio-7.0 wing with 35 deg of sweepback has been made in the Langley 300-MPH 7- by 10-foot tunnel. Blowing over the conventional elevator and blowing down from a nose jet were investigated as a means of trimming the large diving moments at the high momentum and high lift coefficients. The results of the investigation showed that the model with the horizontal tail 0.928 mean aerodynamic chord above the wing-chord plane was stable to the maximum lift coefficient. The large diving-moment coefficients could be trimmed either with a downward blowing nose jet or by blowing over the elevator. Neither the downward blowing nose jet nor blowing over the elevator greatly affected the static longitudinal stability of the model. Trimmed lift coefficients up to 8.8 with blowing over the elevator and up to 11.4 with blowing down at the nose were obtained when the flap was deflected 70 deg and the total momentum coefficients were 3.26 and 4.69.

Turner, Thomas R.↗
NASA NTRS1959

Wind-Tunnel Investigation of a Small-Scale Sweptback-Wing Jet-Transport Model Equipped with an External-Flow Jet-Augmented Double Slotted Flap

A wind-tunnel investigation at low speeds has been made to study the aerodynamic characteristics of a small-scale sweptback-wing Jet-transport model equipped with an external-flow jet-augmented double slotted flap. Included in the investigation were tests of the wing alone to study the effects of varying the spanwise extent of blowing on the full-span flap. The results indicated that the double-slotted-flap arrangement of the present investigation was more efficient in terms of lift and drag than were the external-flow single-slotted-flap arrangements previously tested and gave a substantial reduction In the thrust-weight ratio required for a given lift coefficient under trimmed drag conditions. An increase in the spanwise extent of blowing on the full-span flap was also found to increase the efficiency of the model in terms of the lift and drag but, as would be expected on a sweptback-wing configuration, was accompanied by significant increases in negative pitching moment.

Johnson, Joseph L., Jr.↗
NASA NTRS1979

A simple apparatus for the experimental study of non-steady flow thrust-augmenter ejector configurations

A flexible, and easily modified, test rig is described which allows a one dimensional nonsteady flow stream to be generated, economically from a steady flow source of compressed air. This nonsteady flow is used as the primary stream in a nonsteady flow ejector constituting part of the test equipment. Standard piezo-electric pressure transducers etc. allow local pressures to be studied, as functions of time, in both the primary and secondary (mixed) flow portions of the apparatus. Provision is also made for measuring the primary and secondary mass flows and the thrust generated. Sample results obtained with the equipment are presented.

Khare, J. M.↗
NASA NTRS2010

Testing of SLA-561V in NASA-Ames' Turbulent Flow Duct with Augmented Radiative Heating

As part of Mars Science Laboratory s (MSL) heatshield development program, SLA-561 was tested in NASA Ames Turbulent Flow Duct (TFD) Facility. For these tests, the TFD facility was modified to include a ceramic plate located in the wall opposite to the test model. Normally the TFD wall opposite to the test model is water-cooled steel. Installing a noncooled ceramic plate allows the ceramic to absorb convective heating and radiate the energy back to the test model as the plate heats up. This work was an effort to increase the severity of TFD test conditions. Presented here are the results from these tests.

Sepka, Steven A.↗
NASA NTRS1974

Digital integrated control of a Mach 2.5 mixed-compression supersonic inlet and an augmented mixed-flow turbofan engine

A digitally implemented integrated inlet-engine control system was designed and tested on a mixed-compression, axisymmetric, Mach 2.5, supersonic inlet with 45 percent internal supersonic area contraction and a TF30-P-3 augmented turbofan engine. The control matched engine airflow to available inlet airflow. By monitoring inlet terminal shock position and over-board bypass door command, the control adjusted engine speed so that in steady state, the shock would be at the desired location and the overboard bypass doors would be closed. During engine-induced transients, such as augmentor light-off and cutoff, the inlet operating point was momentarily changed to a more supercritical point to minimize unstarts. The digital control also provided automatic inlet restart. A variable inlet throat bleed control, based on throat Mach number, provided additional inlet stability margin.

Batterton, P. G.↗
NASA NTRS2008

Heating Augmentation in Laminar Flow Due to Heat-Shield Cavities on the Project Orion CEV

An experimental study has been conducted to assess the effects of compression pad cavities on the aeroheating environment of the Project Orion CEV heat-shield at laminar conditions. Testing was conducted in Mach 6 and Mach 10 perfect-gas wind tunnels to obtain heating measurements on and around the compression pads using global phosphor thermography. Consistent trends in heating augmentation levels were observed in the data and correlations of average and maximum heating at the cavities were formulated in terms of the local boundary-layer parameters and cavity dimensions. Additional heating data from prior testing of Genesis and Mars Science Laboratory models were also examined to extend the parametric range of cavity heating correlations.

Hollis, Brian R.↗
NASA NTRS1961

Aerodynamic Characteristics, Temperature, and Noise Measurements of a Large-Scale External-Flow Jet-Augmented-Flap Model with Turbojet Engines Operating

An investigation has been conducted in the Langley full-scale tunnel on a large-scale model powered by turbojet engines with flattened rectangular nozzles. The wing had 35 deg. sweep of the leading edge, an aspect ratio of 6.5, a taper ratio of 0.31, and NACA 65(1)-412 and 65-408 airfoils at the root and tip. The investigation included measurements of the longitudinal aerodynamic characteristics of the model with half-span and full-span flaps and measurements of the sound pressure and skin temperature on the portions of the lower surface of the wing immersed in the jet flow. The tests were conducted over a range or angles of attack from -8 to 16 deg. for Reynolds numbers from 1.8 x 10(exp 6) to 4.4 x 10(exp 6) and a range of momentum coefficients from 0 to 2.0. In general, the aerodynamic results of this investigation made with a large-scale hot-jet model verified the results of previous investigations with small models powered by compressed-air jets. Although blowing was only done over the inboard portion of the wing, substantial amounts of induced lift were also obtained over the outboard portion of the wing. Skin temperatures were about 340 F and wing heating could be handled with available materials without cooling. Random acoustic loadings on the wing surface were high enough to indicate that fatigue failure from this source would require special consideration in the design of an external-flow jet flap system for an airplane.

Fink, Marvin P.↗
NASA NTRS1981

Entrainment and thrust augmentation in pulsatile ejector flows

This study comprised direct thrust measurements, flow visualization by use of a spark shadowgraph technique, and mean and fluctuating velocity measurements with a pitot tube and linearized constant temperature hot-wire anemometry respectively. A gain in thrust of as much as 10 to 15% was observed for the pulsatile ejector flow as compared to the steady flow configuration. From the velocity profile measurements, it is concluded that this enhanced augmentation for pulsatile flow as compared to a nonpulsatile one was accomplished by a corresponding increased entrainment by the primary jet flow. It is also concluded that the augmentation and total entrainment by a constant area ejector critically depends upon the inlet geometry of the ejector. Experiments were performed to evaluate the influence of primary jet to ejector area ratio, ejector length, and presence of a diffuser on pulsatile ejector performance.

Sarohia, V.↗
NASA NTRS1985

An experimental investigation of the transverse pressure gradient associated with curved free jets in the proximity of solid boundaries

An experiment has been performed to determine the mass flow and thrust augmentation associated with the flow of a two-dimensional incompressible jet issued parallel to an adjacent offset wall. A theoretical analysis based on a linear static pressure profile across the jet exit reveals that thrust augmentation is possible only for a wall offset of less than one half of the nozzle exit width. Mass flow augmentation measurements are in reasonable agreement with the proposed theory. Augmented mass flow of over three percent is observed directly, while thrust augmentation in excess of three percent is predicted when measured values of the pressure difference across the exiting jet are supplied to the theory. Measurements of the separation cavity length are presented which complement those given by previous investigators by extending the range to small values of the ratio of the wall offset to the slot height. For large offset ratios it is found that the cavity length approaches 1.25 times the wall offset distance. The initial radius of curvature of the jet centerline is found to be substantially greater than the mean radius of curvature over the cavity length, thereby indicating that the trajectory of the jet does not follow the arc of a circle as has been previously assumed.

Lund, T. S.↗
NASA NTRSDate not supplied

On Generalizably Improving RANS Predictions of Flow Separation and Reattachment

This work presents progress in an ongoing data-driven turbulence modeling effort at NASA Langley Research Center to improve predictions for separated flows. Two augmentation strategies are presented – one to improve predictions for the point of reattachment after smooth-body separation, and another to improve predictions for flow separation due to prolonged adverse pressure gradients. The reattachment augmentation was inspired from lessons learned during attempts at using field inversion and machine learning (FIML); however, it is prescribed as a conventional analytic closed-form expression. Results show that, when introduced into the SST k-w model, it shortens the otherwise overpredicted separation bubble length for three cases characterized by different Reynolds numbers and flow geometries. The second augmentation, which addresses flow separation under prolonged adverse pressure gradients, is inferred via FIML and applied as a neural network within the Spalart-Allmaras model. It uses features that are chosen such that the presented results show an improved predictive accuracy for the training case without affecting other cases where the augmentation is not needed. Further testing is required to establish the generalizability of this augmentation. The rationale behind the chosen features that serve as inputs to both these augmentations is also presented for the benefit of the reader.

machine learning↗
NASA NTRS1948

Altitude-wind-tunnel investigation of tail-pipe burning with a Westinghouse X24C-4B axial-flow turbojet engine

Thrust augmentation of an axial-flow type turbojet engine by burning fuel in the tail pipe has been investigated in the NACA Cleveland altitude wind tunnel. The performance was determined over a range of simulated flight conditions and tail-pipe fuel flows. The engine tail pipe was modified for the investigation to reduce the gas velocity at the inlet of the tail-pipe combustion chamber and to provide an adequate seat for the flame; four such modifications were investigated. The highest net-thrust increase obtained in the investigation was 86 percent with a net thrust specific fuel consumption of 2.91 and a total fuel-air ratio of 0.0523. The highest combustion efficiencies obtained with the four configurations ranged from 0.71 to 0.96. With three of the tail-pipe burners, for which no external cooling was provided, the exhaust nozzle and the rear part of the burner section were bright red during operation at high tail-pipe fuel-air ratios. With the tail-pipe burner for which fuel and water cooling were provided, the outer shell of the tail-pipe burner showed no evidence of elevated temperatures at any operating condition.

Fleming, William A↗
NASA NTRS1983

Supersonic fan engines for military aircraft

Engine performance and mission studies were performed for turbofan engines with supersonic through-flow fans. A Mach 2.4 CTOL aircraft was used in the study. Two missions were considered: a long range penetrator mission and a long range intercept mission. The supersonic fan engine is compared with an augmented mixed flow turbofan in terms of mission radius for a fixed takeoff gross weight of 75,000 lbm. The mission radius of aircraft powered by supersonic fan engines could be 15 percent longer than aircraft powered with conventional turbofan engines at moderate thrust to gross weight ratios. The climb and acceleration performance of the supersonic fan engines is better than that of the conventional turbofan engines.

Franciscus, L. C.↗
NASA NTRS1983

Supersonic fan engines for military aircraft

Engine performance and mission studies were performed for turbofan engines with supersonic through-flow fans. A Mach 2.4 CTOL aircraft was used in the study. Two missions were considered: a long range penetrator mission and a long range intercept mission. The supersonic fan engine is compared with an augmented mixed flow turbofan in terms of mission radius for a fixed takeoff gross weight of 75,000 lbm. The mission radius of aircraft powered by supersonic fan engines could be 15 percent longer than aircraft powered with conventional turbofan engines at moderate thrust to gross weight ratios. The climb and acceleration performance of the supersonic fan engines is better than that of the conventional turbofan engines. Previously announced in STAR as N83-34947

Franciscus, L. C.↗