Search NASA⌕ Search

SEARCH · Search NASA

Results for “fluid model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Two fluid model for thermal stratification in the Apollo cryogenic oxygen tanks

It is observed on Apollo flights that for oxygen densities greater than 42 lb/cu ft the heater operation time to achieve a desired pressure rise is half that which would be required if the energy were uniformly dispersed. A two fluid model was developed to describe this effect of stratification on the tank's pressurization behavior. The increase in pressure rise rate is attributed to compression of the bulk fluid in response to expansion of the heated fluid adjacent to the heater. It is assumed that during the heating operation the adjacent fluid retains nearly all the heater energy and has no mass interaction with the bulk fluid. The hot fluid temperatures predicted by the model are in reasonable correspondence with the observed heater temperatures. The model indicates that the fraction of the fluid interacting with the heater increases with decreasing density, from less than 0.1% at full tank to roughly 1% at 50% quantity, the lowest quantity at which stratification effects on pressure are observed.

Saxton, J. A.↗
NASA NTRS2003

Development of Efficient Real-Fluid Model in Simulating Liquid Rocket Injector Flows

The characteristics of propellant mixing near the injector have a profound effect on the liquid rocket engine performance. However, the flow features near the injector of liquid rocket engines are extremely complicated, for example supercritical-pressure spray, turbulent mixing, and chemical reactions are present. Previously, a homogeneous spray approach with a real-fluid property model was developed to account for the compressibility and evaporation effects such that thermodynamics properties of a mixture at a wide range of pressures and temperatures can be properly calculated, including liquid-phase, gas- phase, two-phase, and dense fluid regions. The developed homogeneous spray model demonstrated a good success in simulating uni- element shear coaxial injector spray combustion flows. However, the real-fluid model suffered a computational deficiency when applied to a pressure-based computational fluid dynamics (CFD) code. The deficiency is caused by the pressure and enthalpy being the independent variables in the solution procedure of a pressure-based code, whereas the real-fluid model utilizes density and temperature as independent variables. The objective of the present research work is to improve the computational efficiency of the real-fluid property model in computing thermal properties. The proposed approach is called an efficient real-fluid model, and the improvement of computational efficiency is achieved by using a combination of a liquid species and a gaseous species to represent a real-fluid species.

Cheng, Gary↗
NASA NTRS1994

Flow properties of the solar wind obtained from white light data and a two-fluid model

The flow properties of the solar wind from 1 R(sub s) to 1 AU were obtained using a two fluid model constrained by density and scale height temperatures derived from white light observations, as well as knowledge of the electron temperature in coronal holes. The observations were obtained with the white light coronographs on SPARTAN 201-1 and at Mauna Loa (Hawaii), in a north polar coronal hole from 1.16 to 5.5 R(sub s) on 11 Apr. 1993. By specifying the density, temperature, Alfven wave velocity amplitude and heating function at the coronal base, it was found that the model parameters fit well the constraints of the empirical density profiles and temperatures. The optimal range of the input parameters was found to yield a higher proton temperature than electron temperature in the inner corona. The results indicate that no preferential heating of the protons at larger distances is needed to produce higher proton than electron temperatures at 1 AU, as observed in the high speed solar wind.

Habbal, Shadia Rifai↗
NASA NTRS1995

Flow properties of the solar wind obtained from white light data, Ulysses observations and a two-fluid model

Using the empirical constraints provided by observations in the inner corona and in interplanetary space. we derive the flow properties of the solar wind using a two fluid model. Density and scale height temperatures are derived from White Light coronagraph observations on SPARTAN 201-1 and at Mauna Loa, from 1.16 to 5.5 R, in the two polar coronal holes on 11-12 Apr. 1993. Interplanetary measurements of the flow speed and proton mass flux are taken from the Ulysses south polar passage. By comparing the results of the model computations that fit the empirical constraints in the two coronal hole regions, we show how the effects of the line of sight influence the empirical inferences and subsequently the corresponding numerical results.

Habbal, Shadia Rifai↗
NASA NTRS1995

Time-dependent simulation of oblique MHD cosmic-ray shocks using the two-fluid model

Using a new, second-order accurate numerical method we present dynamical simulations of oblique MHD cosmic-ray (CR)-modified plane shock evolution. Most of the calculations are done with a two-fluid model for diffusive shock acceleration, but we provide also comparisons between a typical shock computed that way against calculations carried out using the more complete, momentum-dependent, diffusion-advection equation. We also illustrate a test showing that these simulations evolve to dynamical equilibria consistent with previously published steady state analytic calculations for such shocks. In order to improve understanding of the dynamical role of magnetic fields in shocks modified by CR pressure we have explored for time asymptotic states the parameter space of upstream fast mode Mach number, M(sub f), and plasma beta. We compile the results into maps of dynamical steady state CR acceleration efficiency, epsilon(sub c). We have run simulations using constant, and nonisotropic, obliquity (and hence spatially) dependent forms of the diffusion coefficient kappa. Comparison of the results shows that while the final steady states achieved are the same in each case, the history of CR-MHD shocks can be strongly modified by variations in kappa and, therefore, in the acceleration timescale. Also, the coupling of CR and MHD in low beta, oblique shocks substantially influences the transient density spike that forms in strongly CR-modified shocks. We find that inside the density spike a MHD slow mode wave can be generated that eventually steepens into a shock. A strong layer develops within the density spike, driven by MHD stresses. We conjecture that currents in the shear layer could, in nonplanar flows, results in enhanced particle accretion through drift acceleration.

Frank, Adam↗
NASA NTRS1985

Two-fluid models of turbulence

The defects of turbulence models are summarized and the importance of so-called nongradient diffusion in turbulent fluxes is discussed. The mathematical theory of the flow of two interpenetrating continua is reviewed, and the mathematical formulation of the two fluid model is outlined. Results from plane wake, axisymmetric jet, and combustion studies are shown.

Spalding, D. B.↗
NASA NTRS1984

Numerical investigation of fluid models with full electron and proton thermal conduction equations for the quiet solar wind

The effect of using full equations (rather than Fourier law expressions) for the electron and proton thermal conductivities in conjunction with community, momentum, and temperature equations for the description of spherically symmetric quiet solar wind states is investigated numerically. For this purpose a time-dependent method is used, and steady state solutions in both subsonic and supersonic regimes between the sun and 5 AU are obtained and presented. The consequences for one-fluid and two-fluid models for the solar wind are summarized and discussed.

Cuperman, S.↗
NASA NTRS1986

Interaction of the solar wind with interstellar neutral hydrogen - Three-fluid model

It is commonly assumed in models of the solar wind-interstellar neutral hydrogen interaction that the ionized interstellar particles are quickly assimilated into the solar wind proton population and 'become indistinguishable' from the original solar wind. This assumption leads to the prediction that the solar wind proton temperature should increase with radius in the outer heliosphere. This temperature increase has not been observed. It is pointed out that assimilation of the interstellar particles to the point of indistinguishability takes place on the very long Coulomb collision time scale, and is not expected to occur within the heliosphere. Results are presented of a three-fluid model of the solar wind which consists of comoving thermal populations of protons of solar origin, protons produced by ionization of interstellar hydrogen, and electrons. The steady-state results yield a solar wind with a 'core' proton distribution which cools adiabatically, and a 'halo' of interstellar pickup protons which is maintained near 10 to the 7th K by the energy input of continued ionization and pickup. Such a distribution will not be observed to manifest the temperature increase at large heliocentric distances which is predicted from a one-fluid analysis. Further time-dependent calculations show a strong correlation between the densities of the solar wind and the interstellar pickup protons. It is suggested that the interstellar pickup population may be observable by the Voyager plasma instruments in low resolution mode during periods of high solar wind density and low solar wind temperature.

Isenberg, P. A.↗
NASA NTRS2012

Thermal and Fluid Modeling of the CRYogenic Orbital TEstbed (CRYOTE) Ground Test Article (GTA)

The purpose of this study was to anchor thermal and fluid system models to data acquired from a ground test article (GTA) for the CRYogenic Orbital TEstbed - CRYOTE. To accomplish this analysis, it was broken into four primary tasks. These included model development, pre-test predictions, testing support at Marshall Space Flight Center (MSFC} and post-test correlations. Information from MSFC facilitated the task of refining and correlating the initial models. The primary goal of the modeling/testing/correlating efforts was to characterize heat loads throughout the ground test article. Significant factors impacting the heat loads included radiative environments, multi-layer insulation (MLI) performance, tank fill levels, tank pressures, and even contact conductance coefficients. This paper demonstrates how analytical thermal/fluid networks were established, and it includes supporting rationale for specific thermal responses seen during testing.

Piryk, David↗
NASA NTRS2024

Understanding the Variability of Helium Abundance in the Solar Corona Using Three Fluid Modeling and Ultraviolet Observations

The variability of helium abundance in the solar corona and the solar wind is an important signature of solar activity, solar cycle, and solar wind sources, as well as coronal heating processes. Motivated by recently reported remote-sensing UV imaging observations by Helium Resonance Scattering in the Corona and Heliosphere payload sounding rocket of helium abundance in the inner corona on 2009 September 14 near solar minimum, we present the results of the first three-dimensional three-fluid (electrons, protons, and alpha particles) model of tilted coronal streamer belt and slow solar wind that illustrates the various processes leading to helium abundance differentiation and variability. We find good qualitative agreement between the three-fluid model and the coronal helium abundance variability deduced from UV observations of streamers, providing insight on the effects of the physical processes, such as heating, gravitational settling, and interspecies Coulomb friction in the outflowing solar wind that produce the observed features. The study impacts our understanding of the origins of the slow solar wind.

Leon Ofman↗
NASA NTRS1992

A two-fluid model of the solar wind

A method is presented for the integration of the two-fluid solar-wind equations which is applicable to a wide variety of coronal base densities and temperatures. The method involves proton heat conduction, and may be applied to coronal base conditions for which subsonic-supersonic solar wind solutions exist.

Sandbaek, O.↗
NASA NTRS1992

Acoustic intensity calculations for axisymmetrically modeled fluid regions

An algorithm for calculating acoustic intensities from a time harmonic pressure field in an axisymmetric fluid region is presented. Acoustic pressures are computed in a mesh of NASTRAN triangular finite elements of revolution (TRIAAX) using an analogy between the scalar wave equation and elasticity equations. Acoustic intensities are then calculated from pressures and pressure derivatives taken over the mesh of TRIAAX elements. Intensities are displayed as vectors indicating the directions and magnitudes of energy flow at all mesh points in the acoustic field. A prolate spheroidal shell is modeled with axisymmetric shell elements (CONEAX) and submerged in a fluid region of TRIAAX elements. The model is analyzed to illustrate the acoustic intensity method and the usefulness of energy flow paths in the understanding of the response of fluid-structure interaction problems. The structural-acoustic analogy used is summarized for completeness. This study uncovered a NASTRAN limitation involving numerical precision issues in the CONEAX stiffness calculation causing large errors in the system matrices for nearly cylindrical cones.

Hambric, Stephen A.↗
NASA NTRS2000

Validation of an All-Pressure Fluid Drop Model: Heptane Fluid Drops in Nitrogen

Despite the fact that supercritical fluids occur both in nature and in industrial situations, the fundamentals of their behavior is poorly understood because supercritical fluids combine the characteristics of both liquids and gases, and therefore their behavior is not intuitive. There are several specific reasons for the lack of understanding: First, data from (mostly optical) measurements can be very misleading because regions of high density thus observed are frequently identified with liquids. A common misconception is that if in an experiment one can optically identify "drops" and "ligaments", the observed fluid must be in a liquid state. This inference is incorrect because in fact optical measurements detect any large change (i.e. gradients) in density. Thus, the density ratio may be well below Omicron(10(exp 3)) that characterizes its liquid/gas value, but the measurement will still identify a change in the index of refraction providing that the change is sudden (steep gradients). As shown by simulations of supercritical fluids, under certain conditions the density gradients may remain large during the supercritical binary fluids mixing, thus making them optically identifiable. Therefore, there is no inconsistency between the optical observation of high density regions and the fluids being in a supercritical state. A second misconception is that because a fluid has a liquid-like density, it is appropriate to model it as a liquid. However, such fluids may have liquid-like densities while their transport properties differ from those of a liquid. Considering that the critical pressure of most fuel hydrocarbons used in Diesel and gas turbine engines is in the range of 1.5 - 3 MPa, and the fact that the maximum pressure attained in these engines is about 6 Mps, it is clear that the fuel in the combustion chamber will experience both subcritical and supercritical conditions. Studies of drop behavior over a wide range of pressures were performed in the past, however none of these studies identified the crucial differences between the subcritical and supercritical behavior. In fact, in two of these studies, it was found that the subcritical and supercritical behavior is similar as the drop diameter decreased according to the classical d(exp 2)-law over a wide range of pressures and drop diameters. The present study is devoted to the exploration of differences in fluid-behavior characteristics under subcritical and supercritical conditions in the particular case of heptane fluid drops in nitrogen; these substances were selected because of the availability of experimental observations for model validation.

Harstad, K.↗
NASA NTRS1988

The magnetic mirror force in plasma fluid models

In the past decade, there have been several attempts to include the magnetic mirror force in the equation of motion for a plasma in a fluid formalism. In the process, some confusion has been evident regarding when and how this should be done. This problem has been addressed in the literature, but these treatments appear to have been forgotten or misunderstood. The mathematical arguments are summarized so that the physical consequences are readily perceived. It is shown that for an isotropic plasma fluid, in the direction parallel or anti-parallel to a magnetic field, the forces associated with a diverging magnetic field cancel out. Only for anisotropies in the fluid properties does the diverging field influence the plasma dynamics.

Comfort, R. H.↗
NASA NTRS1995

Self-consistent solar wind-LISM interaction including neutrals: A 4-fluid model

We investigate the interaction between the heliosphere and local interstellar medium, including charge-exchange self-consistently between the neutral and ionized components. The system is modelled as consisting of neutral hydrogen, protons and electrons. The electrons are assumed to contribute to the dynamics via a pressure that is everywhere equal to the proton pressure. The fluid equations for the protons and hydrogen are solved self-consistently, assuming the two species interact only via charge exchange. The protons are treated as a single isotropic fluid. The hydrogen is decomposed into three isotropic fluids: hydrogen of interstellar origin with characteristic temperature of approximately 104 K, hydrogen produced via charge exchange in the post-shock solar wind, with characteristic temperature of approximately 105 K, and hydrogen produced via charge exchange in the supersonic solar wind, relatively cool but expanding radially outward with the solar wind speed. Two-Dimensional time-dependent numerical simulations of this system are performed to calculate the number density, temperature and bulk velocity of neutral hydrogen and plasma everywhere in the heliosphere. These quantities are compared to relevant solar wind observations. Implications for the pick-up process in the supersonic solar wind, as well as heating and deceleration of the wind, are addressed.

Williams, L. L.↗