Search NASA⌕ Search

SEARCH · Search NASA

Results for “frequency ratio”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Load and stability measurements on a soft-inplane rotor system incorporating elastomeric lead-lag dampers

An experimental investigation was conducted of the dynamic response and inplane stability associated with a new soft-inplane helicopter rotor. The unique feature of this rotor was the use of an internal elastomeric damper to restrain the blade inplane motion about the lead-lag hinge. The properties of the elastomer were selected to provide both a nominal first inplane frequency ratio of 0.65 and sufficient damping to eliminate the need for additional external damping sources to prevent ground resonance on a typical fuselage structure. For this investigation a 1/5-scale aeroelastic model was used to represent the rotor. The four-blade model had a diameter of 3.05 m (10 ft) and a solidity of 0.103. The first out-of-plane frequency ratio was 1.06. The model was tested in hover and in forward flight up to an advance ratio of 0.45. At each forward speed the rotor lift was varied up to simulated maneuver conditions. The measured rotor loads and response were within acceptable limits, and no adverse response qualities were observed. Moderate out-of-plane hub moments were measured, even for zero lift, to indicate the beneficial control power available for this design. Blade inplane stability testing indicated that the rotor system damping remained at moderate levels throughout the operating envelope.

Weller, W. H.↗
NASA NTRS2022

The Influence of Land Use and Land Cover Change on Landslide Susceptibility in the Lower Mekong River Basin

The Lower Mekong River Basin in Southeast Asia experiences frequent rainfall-triggered landslides especially during the monsoon season. In this study, the influence of land use and land cover change and other causative factors on landslide susceptibility is evaluated in the Lower Mekong Basin. Frequency ratio analysis is performed to quantify the relationship between LULC change and susceptibility. Detailed landslide inventory maps are used for analysis with yearly LULC maps. The LULC change is used as a contributing variable in a logistic regression-based susceptibility model with other variables including distance to roads, slope, aspect, forest loss, and soil properties. The Receiver Operating Characteristic (ROC) curve and Area Under the Curve are estimated for the model trained by each landslide inventory. The models show good performance, with AUC values ranging from 0.697 to 0.958 and an average AUC equal to 0.820. Both the Frequency Ratio analysis and the Logistic Regression models indicate LULC change from agricultural land to forest has a positive correlation with landslide occurrence. The most significant factors in the models are found to be distance to roads, slope, and aspect. A better understanding of the effects of LULC on landslide susceptibility can be useful for local land and disaster management and for the implementation of LULC as a factor in future susceptibility models. Using datasets that are unique to the Lower Mekong region, this study provides additional insights into the relationship between causative factors and landslide activity to better inform regional and global landslide susceptibility modeling.

River Basin↗
NASA NTRS2007

Wide Tuning Capability for Spacecraft Transponders

A document presents additional information on the means of implementing a capability for wide tuning of microwave receiver and transmitter frequencies in the development reported in the immediately preceding article, VCO PLL Frequency Synthesizers for Spacecraft Transponders (NPO- 42909). The reference frequency for a PLL-based frequency synthesizer is derived from a numerically controlled oscillator (NCO) implemented in digital logic, such that almost any reference frequency can be derived from a fixed crystal reference oscillator with microhertz precision. The frequency of the NCO is adjusted to track the received signal, then used to create another NCO frequency used to synthesize the transmitted signal coherent with, and at a specified frequency ratio to, the received signal. The frequencies can be changed, even during operation, through suitable digital programming. The NCOs and the related tracking loops and coherent turnaround logic are implemented in a field-programmable gate array (FPGA). The interface between the analog microwave receiver and transmitter circuits and the FPGA includes analog-to-digital and digital-toanalog converters, the sampling rates of which are chosen to minimize spurious signals and otherwise optimize performance. Several mixers and filters are used to properly route various signals.

Lux, James↗
NASA NTRS2008

Validation of Cardiovascular Parameters During NASA's Functional Task Test

Microgravity-induced physiological changes, including cardiovascular deconditioning may impair crewmembers f capabilities during exploration missions on the Moon and Mars. The Functional Task Test (FTT), which will be used to assess task performance in short and long duration astronauts, consists of 7 functional tests to evaluate crewmembers f ability to perform activities to be conducted in a partial-gravity environment or following an emergency landing on Earth. The Recovery from Fall/Stand Test (RFST) tests both the subject fs ability to get up from a prone position and orthostatic intolerance. PURPOSE: Crewmembers have never become presyncopal in the first 3 min of quiet stand, yet it is unknown whether 3 min is long enough to cause similar heart rate fluctuations to a 5-min stand. The purpose of this study was to validate and test the reliability of heart rate variability (HRV) analysis of a 3-min quiet stand. METHODS: To determine the validity of using 3 vs. 5-min of standing to assess HRV, 7 healthy subjects remained in a prone position for 2 min, stood up quickly and stood quietly for 6 min. ECG and continuous blood pressure data were recorded. Mean R-R interval and spectral HRV were measured in minutes 0-3 and 0-5 following the heart rate transient due to standing. Significant differences between the segments were determined by a paired t-test. To determine the reliability of the 3-min stand test, 13 healthy subjects completed 3 trials of the complete FTT on separate days, including the RFST with a 3-min stand test. Analysis of variance (ANOVA) was performed on the HRV measures. RESULTS: Spectral HRV measures reflecting autonomic activity were not different (p>0.05) during the 0-3 and 0-5 min segment (mean R-R interval: 738+/-74 ms, 728+/-69 ms; low frequency to high frequency ratio: 6.5+/-2.2, 7.7+/-2.7; normalized high frequency: 0.19+/-0.03, 0.18+/-0.04). The average coefficient of variation for mean R-R interval, systolic and diastolic blood pressures in the prone position and stand test were less than 8% for the test sessions. ANOVA results yielded a greater inter-subject variability (p.0.006) than inter-session variability (p>0.05) for HRV in the stand test. CONCLUSION: These studies show that a 3 minute stand delivers repeatable cardiovascular heart rate and BP data in the context of this larger series of tests such as the FTT.

Arzeno, N. M.↗
NASA NTRS1985

A dual frequency microstrip antenna for Ka band

For fixed satellite communication systems at Ka band with downlink at 17.7 to 20.2 GHz and uplink at 27.5 to 30.0 GHz, the focused optics and the unfocused optics configurations with monolithic phased array feeds have often been used to provide multiple fixed and multiple scanning spot beam coverages. It appears that a dual frequency microstrip antenna capable of transmitting and receiving simultaneously is highly desirable as an array feed element. This paper describes some early efforts on the development and experimental testing of a dual frequency annular microstrip antenna. The antenna has potential application for use in conjunction with a monolithic microwave integrated circuit device as an active radiating element in a phased array of phased array feeds. The antenna is designed to resonate at TM sub 12 and TM sub 13 modes and tuned with a circumferential microstrip ring to vary the frequency ratio. Radiation characteristics at both the high and low frequencies are examined. Experimental results including radiating patterns and swept frequency measurements are presented.

Lee, R. Q.↗
NASA NTRS1959

Flutter Tests of Some Simple Models at a Mach Number of 7.2 in Helium Flow

Results of hypersonic flutter tests on some simple models are presented. The models had rectangular plan forms of panel aspect ratio 1.0, no sweepback, and bending-to-torsion frequency ratios of about 1/3. Two airfoil sections were included in the tests; double wedges of 5-, 10-, and 15-percent thickness and flat plates with straight, parallel sides and beveled leading and trailing edges. The models were supported by a cantilevered shaft. The double-wedge wings were tested in helium at a Mach number of 7.2. An effect of airfoil thickness on flutter speed was found, thicker wings requiring more stiffness to avoid flutter. A few tests in air at a Mach number of 6.9 showed the same thickness effect and also indicated that tests in helium would predict conservative flutter boundaries in air. The data in air and helium seemed to be correlated by piston-theory calculations. Piston-theory calculations agreed well with experiment for the thinner models but began to deviate as the thickness parameter MT approached and exceeded 1.0. A few tests on flat-plate models with various elastic-axis locations were made. Piston-theory calculations would not satisfactorily predict the flutter of these models, probably because of their blunt leading edges.

Morgan, Homer G.↗
NASA NTRS1967

Experimental coherent fractional frequency multiplier at S-band

Experimental circuit produces an efficient fractional frequency multiplier that will operate on a 5.6 mw, 2101.8 MHz input signal to achieve an output-to-input frequency ratio of 240/221. Step-recovery diodes used in all frequency-changing stages result in a coherent offset frequency.

Mostrum, R. A.↗
NASA NTRS2024

An Airborne Multi-Frequency Microwave Analysis of Precipitation within Two Winter Cyclones

NASA’s Investigation of Microphysics and Precipitation for Atlantic Coast-Threatening Snowstorms (IMPACTS) field campaign gathered data using “satellite-simulating” (albeit with higher-resolution data than satellites currently provide) and in situ aircraft to study snowstorms, with an emphasis on banding. This study used three IMPACTS microwave instruments—two passive and one active—chosen for their sensitivity to precipitation microphysics. The 10–37-GHz passive frequencies were well suited for detecting light precipitation and differentiating rain intensities over water. The 85–183-GHz frequencies were more sensitive to cloud ice, with higher cloud tops manifesting as lower brightness temperatures, but this did not necessarily correspond well to near-surface precipitation. Over land, retrieving precipitation information from radiometer data is more difficult, requiring increased reliance on radar to assess storm structure. A dual-frequency ratio (DFR) derived from the radar’s Ku- and Ka-band frequencies provided greater insight into storm microphysics than reflectivity alone. Areas likely to contain mixed-phase precipitation (often the melting layer/bright band) generally had the highest DFR, and high-altitude regions likely to contain ice usually had the lowest DFR. The DFR of rain columns increased toward the ground, and snowbands appeared as high-DFR anomalies.

Amanda Richter↗
NASA NTRS1989

Pulse-Population Modulation For Induction Machines

Low-frequency synthesizer developed to provide low-frequency waveform by synthesis from high-frequency power system. Waveform assembled by allowing conduction of discrete half cycles of high-frequency carrier. Frequency of synthesized wave controlled by pulse pattern. By controlling relationship between slip and stator frequencies, one operates induction motor either as motor or generator. Such bidirectional energy transducer used as starter/generator for engine, or as servo-mechanism for control of acceleration and deceleration. Other advantages include operation under controlled voltage-to-frequency ratios to maintain high-efficiency and high power factor, and no reflection of low-frequency noise into 20-kHz distribution bus.

Hansen, Irving G.↗
NASA NTRS1977

Satellite-based interference analyzer

System identifies terrestrial sources of radiofrequency interference and measures their frequency spectra and amplitudes. Designed to protect satellite communication networks, system measures entire noise spectrum over selected frequency band and can raster-scan geographical region to locate noise sources. Once interference is analyzed, realistic interference protection ratios are determined and mathematical models for predicting ratio-frequency noise spectra are established. This enhances signal-detection and locates optimum geographical positions and frequency bands for communication equipment.

Varice, H.↗
NASA NTRS2008

Retrieval of Snow and Rain From Combined X- and W-B and Airborne Radar Measurements

Two independent airborne dual-wavelength techniques, based on nadir measurements of radar reflectivity factors and Doppler velocities, respectively, are investigated with respect to their capability of estimating microphysical properties of hydrometeors. The data used to investigate the methods are taken from the ER-2 Doppler radar (X-band) and Cloud Radar System (W-band) airborne Doppler radars during the Cirrus Regional Study of Tropical Anvils and Cirrus Layers-Florida Area Cirrus Experiment campaign in 2002. Validity is assessed by the degree to which the methods produce consistent retrievals of the microphysics. For deriving snow parameters, the reflectivity-based technique has a clear advantage over the Doppler-velocity-based approach because of the large dynamic range in the dual-frequency ratio (DFR) with respect to the median diameter Do and the fact that the difference in mean Doppler velocity at the two frequencies, i.e., the differential Doppler velocity (DDV), in snow is small relative to the measurement errors and is often not uniquely related to Do. The DFR and DDV can also be used to independently derive Do in rain. At W-band, the DFR-based algorithms are highly sensitive to attenuation from rain, cloud water, and water vapor. Thus, the retrieval algorithms depend on various assumptions regarding these components, whereas the DDV-based approach is unaffected by attenuation. In view of the difficulties and ambiguities associated with the attenuation correction at W-band, the DDV approach in rain is more straightforward and potentially more accurate than the DFR method.

Liao, Liang↗
NASA NTRS2010

Statistics of Cloud Optical Properties from Airborne Lidar Measurements

Cloud optical properties, such as extinction-to-backscatter ratio and depolarization ratio, have a significant impact on the accuracy of cloud extinction retrievals from lidar systems because parameterizations of these variables are often used in non-ideal conditions to determine cloud type and optical depth. Statistics and trends of these optical parameters were analyzed for four years, 2003-2007, of Cloud Physics Lidar data during five projects of varying geographic locations. Extinction-to-backscatter ratio (at 532 nm) was derived by calculating the transmission loss through the cloud layer, while depolarization ratio was computed using the parallel and perpendicular polarized 1064 nm channels. The majority of the cloud layers yielded an S-ratio between 10 and 40 sr with the S-ratio frequency distribution centered at 25 sr for ice clouds, 21 sr for mixed phase clouds, and 11 sr for water clouds. On average for ice clouds, S ratio slightly decreased with decreasing temperature, while depolarization ratio increased significantly as temperatures decreased. Trends for water and mixed phase clouds were also observed. Ultimately, these observed trends in optical properties as a function of temperature and geographic location will improve current parameterizations of extinction-to-backscatter ratio, which consequently increases accuracy in cloud optical depth and radiative forcing estimates.

Yorks, John E.↗
NASA NTRS1987

Frequency and load ratio effects on critical strain energy release rate Gc thresholds of graphite/epoxy composites

Graphite/epoxy composite laminates of T300/BP907 and AS6/HST-7 were axial-tension fatigue tested. Tests were conducted at 5 and 10 Hz, and at loading ratios of R = 0.1 and R = 0.5. Edge delamination was monitored as a function of number of fatigue cycles by monitoring stiffness reduction during fatigue testing. Delamination was confirmed and documented using dye-enhanced X-ray and optical photography. Critical strain energy release rates were then calculated. The composites delaminated readily, with loading ratio having a significant influence. Frequency effects were negligible.

Adams, Donald F.↗
NASA NTRS1986

Observations concerning the generation and propagation of Type III solar bursts

A number of Type III bursts were observed during the Helios missions in which the burst exciter passed over the spacecraft, as evidenced by strong electric field fluctuations near the plasma frequency. Six of these were suitable for detailed study. Of the six events, one was ambiguous, one showed what is interpreted as a switchover from harmonic to fundamental, and the rest all generated fundamental at onset. This would be expected if both fundamental and harmonic are generated, as, at a fixed frequency, the fundamental will be generated earlier. For the event which seems to show both fundamental and harmonic emission, the frequency ratio is not exactly 2. This is explained in terms of a time delay of the fundamental, due to scattering and diffusion in the source region. A time delay of the order of 600 seconds at 1 AU and 20 kHz, and inversely proportional to frequency, is required to explain the observations. Crude estimates show that delay times at least this long may be attributed to trapping and scattering.

Kellogg, P. J.↗
NASA NTRS2007

Quasi-Periodic Variability in NGC 5408 X-1

We report the discovery with XMM-Newton of quasiperiodic variability in the 0.2 - 10 keV X-ray flux from the ultraluminous X-ray source NGC 5408 X-1. The average power spectrum of all EPIC-pn data reveals a strong 20 mHz QPO with an average amplitude (rms) of 9%, and a coherence, Q identical with nu(sub 0)/sigma approximately equal to 6. In a 33 ksec time interval when the 20 mHz QPO is strongest we also find evidence for a 2nd QPO peak at 15 mHz, the first indication for a close pair of QPOs in a ULX source. Interestingly, the frequency ratio of this QPO pair is inconsistent with 3:2 at the 3 sigma level, but is consistent with a 4:3 ratio. A powerlaw noise component with slope near 1.5 is also present below 0.1 Hz with evidence for a break to a flatter slope at about 3 mHz. The source shows substantial broadband variability, with a total amplitude (rms) of about 30% in the 0.1 - 100 mHz frequency band, and there is strong energy dependence to the variability. The power spectrum of hard X-ray photons (greater than 2 keV) shows a "classic" flat-topped continuum breaking to a power law with index 1.5 - 2. Both the break and 20 mHz QPO are detected in the hard band, and the 20 mHz QPO is essentially at the break. The QPO is both strong and narrow in this band, having an amplitude (rms) of 15%, and Q approx. equal to 25. The energy spectrum is well fit by three components, a "cool" disk with kT = 0.15 keV, a steep power law with index 2.56, and a thermal plasma at kT = 0.87 keV. The disk, power law, and thermal plasma components contribute 35, 60, and 5% of the 0.3 - 10 keV flux, respectively. Both the timing and spectral properties of NGC 5408 X-1 are strikingly reminiscent of Galactic black hole systems at high inferred accretion rates, but with its characteristic frequencies (QPO and break frequencies) scaled down by a factor of 10 - 100. We discuss the implications of these findings in the context of models for ULXs, and their implications for the object's mass.

Strohmayer, Tod E.↗
NASA NTRS1973

Hingeless rotor vibration and loads at high advance ratio

Experimental values of mean and oscillatory shaft force aeroelastic derivatives with respect to cyclic pitch are presented in dimensionless coefficient form for stiff-bladed hingeless rotors operating at high advance ratio. Good agreement with theory is obtained for the 2P components, in rotating axes, of the oscillatory hub moment derivatives. Trends were predicted for the mean components. Experimental plots of the azimuthal distribution of blade flap bending moment due to cyclic pitch are compared with theoretical for high values of flap frequency ratio and advance ratio. Good agreement is found near the blade root. The similarity parameters that should be preserved in the scale model testing of stiff-bladed hingeless rotors at high advance ratio are reviewed, and some aspects of hingeless rotor wind tunnel testing are considered.

Watts, G. A.↗
NASA NTRS1975

Type III solar radio bursts and the fundamental-harmonic hypothesis

The observational evidence is reviewed for the occurrence of type III solar radio bursts in pairs with frequency ratio two to one. We show that the observations can be explained under the hypothesis that there is a tendency for a type III burst to be followed by a second burst within approximately one second. This explanation leads to fewer difficulties than the hypothesis that type III bursts occur in pairs, one member being emitted at the fundamental of the local coronal plasma frequency, the other at its second harmonic. We conclude that in general, type III bursts are emitted at the second harmonic of the plasma frequency and that type III theories should account for this and only under very special circumstances (which are rare) for the emission at the fundamental and the second harmonic.

Rosenberg, H.↗