SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Computer code determines rotor exit flow from hub to tip. RTOD (Radial Turbine Off-Design), computes off-design performance of radial turbine by modeling flow with stator viscous and trailing-edge losses, and with vaneless space loss between stator and rotor, and with rotor incidence, viscous, clearance, trailing-edge, and disk friction losses.
The turbine losses for the fuel and oxidizer turbines at the FPL condition were assessed by a quasi-3D loss analysis method. This loss analysis method uses two flow codes - MERIDL and TSONIC - to calculate the flow velocities along the blade surfaces and endwalls. The velocities are then used as input to the boundary layer code - BLAYER - to calculate the friction losses due to incidence, secondary flow, and tip clearance. The loss analysis for the fuel turbine indicated an overall two-stage efficiency of about 90%. The largest loss was due to rotor tip clearance. The loss analysis for the oxidizer turbine is nearly completed. Results for the first stage of the two-stage design indicates an efficiency of about 80%, with high losses due to rotor incidence and blade and endwall friction.
Surface waves are attenuated by a fluid or gas surrounding the surface of propagation, an effect caused by frictional losses determined by the fluid or gas viscosity and by the emission of compression waves into the environment. The paper reports a large reversible reduction in attenuation of surface waves at frequencies as low as 2 MHz by outgassing treatments of some materials, suggesting that at such frequencies vacuum encapsulation is a desirable procedure. Outgassing experiments were performed on a delay line constructed from high-density p.z.t.-8 (lead-zirconate-titanate). The delay line configuration was a slab waxed onto a metal base with coaxial connectors mounted near and connected by gold-wire leads to the interdigital finger sets. Output signal enhancements by as much as 8 dB were achieved after overnight evacuation at 10 to the -2 torr at room temperature.
The dynamics of granular materials has proved difficult to model, primarily because of the complications arising from inelastic losses, friction, packing, and the effect of many grains being in contact simultaneously. The kinetic model of granular systems is similar to the kinetic theory of gases, except that collisional energy losses are always present in the former and must be treated explicity. Few granular materials on Earth are describable by this limiting model, since gravity tends to collapse the grains into a high density state where Coulombic friction effects are dominant. The planned Space Station offers an unusual opportunity to test the kinetic grain model and to explore its predictions. Without gravity, the regime of low interparticle velocities (where an elastic description of the collision is still valid) can be investigated. This will allow for direct interpretation by dynamical computer simulations as well as by the kinetic theory. The dynamics of spherical grains inside a clear box would be examined. Results would be compared with the predictions of the kinetic theory and computer simulations.
The pressure ratio across a turbine provides a certain amount of ideal energy that is available to the turbine for producing work. The portion of the ideal energy that is not converted to work is considered to be a loss. One of the more important and difficult aspects of turbine design is the prediction of the losses. The primary cause of losses is the boundary layer that develops on the blade and end wall surfaces. Boundary-layer theory is used to calculate the parameters needed to estimate viscous (friction) losses.
Preliminary tests have been made of a small burner to meet the requirements for application to supersonic ram jets. The principal requirements were taken as: (1) efficient combustion in a high-velocity air stream, (2) utilization for combustion of only a small fraction of the air passing through the unit, (3) low resistance to air flow, (4) simple construction, and (5) light weight. Tests of a small burner were carried to stream velocities of nearly 150 feet per second and fuel rates such that one-eighth to one-fourth of the total air was involved in combustion. Commercial propane was selected as the fuel since its low boiling point facilitated vaporization. Combustion which was 80 percent complete along with low aerodynamic losses was obtained by injecting the fuel evenly, prior to ignition, and allowing it to mix with the air without appreciably disturbing the stream. The pressure drop due to frictional losses around the burner and to the adjacent inside walls of the ram jet is small compared with the pressure drop due to combustion.
The dynamics of granular materials has proved difficult to model, primarily because of the complications arising from inelastic losses, friction, packing, and the effect of many grains being in contact simultaneously. One interesting limit for which it was recently possible to construct a theory is that where the grain-grain interactions are dominated by binary collisions. The kinetic model of granular systems if similar to the kinetic theory of gases, except that collisional energy losses are always present in the former and must be treated explicitly. Few granular materials on Earth are describable by this limiting model, since gravity tends to collapse the grains into a high-density state where Coulombic friction effects are dominant. The planned Space Station offers an unusual opportunity to test the kinetic grain model and to explore its predictions. Without gravity, the regime of low interparticle velocities, where an elastic description of the collision is still valid, is investigated. This will allow direct interpretation by dynamical computer simulations as well as by kinetic theory.
In this report we discuss the details of the correlations used to recognize flow patterns and predict frictional losses, heat and mass transfer in the cryogenic two phase flow. The emphasis are put on the formulation of the correlation problem in terms of concise parametric and functional spaces allowing for efficient online search of the model parameters and accurate prediction of the phenomena observed during cryogenic loading. A special attention is paid to the discussion of the correlation dependence on the gravity. In this context the physics of stability, friction, and boiling in the two-phase flow that underlies the required correlations is discussed.
As part of the DOE/NASA Automotive Stirling Engine Project, tests were made at NASA Lewis Research Center to determine whether appendix gap losses could be reduced and Stirling engine performance increased by installing an additional piston ring near the top of each piston dome. An MTI-designed upgraded Mod I Automotive Stirling Engine was used. Unlike the conventional rings at the bottom of the piston, these hot rings operated in a high temperature environment (700 C). They were made of a high temperature alloy (Stellite 6B) and a high temperature solid lubricant coating (NASA Lewis-developed PS-200) was applied to the cylinder walls. Engine tests were run at 5, 10, and 15 MPa operating pressure over a range of operating speeds. Tests were run both with hot rings and without to provide a baseline for comparison. Minimum data to assess the potential of both the hot rings and high temperature low friction coating was obtained. Results indicated a slight increase in power and efficiency, an increase over and above the friction loss introduced by the hot rings. Seal leakage measurements showed a significant reduction. Wear on both rings and coating was low.
Measurements of electrical conductivity, ultrasonic surface wave attenuation, and internal friction loss were made on aluminum alloys 7079-T6, 2219-T31, and 2219-T81 as a function of the onset of stress corrosion.
Liquid-gas separator design with reduced friction loss for MHD generators using two phase convergent-divergent nozzles
Proposed rolling electric motor has output shaft speed reductions of 1000 to 1 or better. Light compact unit uses no gears or pulleys to reduce speed presenting less bulk and frictional loss, and more efficiency.
Two-layer thermal barrier coating, consisting of metal-CrA1Y bond coating and calcium silicate ceramic outer layer, greatly improves resistance of turbine parts to hot corrosion from fuel and air impurities. Both layers can be plasma sprayed, and ceramic layer may be polished to reduce frictional losses. Ceramic provides thermal barrier, so parts operate cooler metal temperatures, coolant flow can be reduced, or gas temperatures increased. Lower grade fuels also can be used.
In contrast to hydrodynamic bearings, which depend for low-friction characteristics on a fluid film between the journal and the bearing surfaces, roller-element bearings employ a number of balls or rollers that roll in an annular space. The paper briefly outlines the advantages and disadvantages of roller-element bearings as compared to hydrodynamic bearings. The discussion covers bearing types, rolling friction, friction losses in rolling bearings, contact stresses, deformations, kinematics (normal and high speeds), bearing dynamics including elastohydrodynamics, load distribution, lubrication (grease, solid oil, oil-air mist), specific dynamic capacity and life, specific static capacity, and fatigue or wearout (elastohydrodynamics, wear). Rolling bearing wear factor as a function of operating environment is plotted and discussed.
The design and construction of a reciprocating test vehicle to be used in evaluating hydrodynamic oil pumping rings are discussed. In addition, experimental test data are presented for three pumping ring designs that were constructed from Tin-Based Babbitt (SAE 11), Bearing Bronze (SAE 660), and Mechanical Carbon Graphite (Union Carbide Grade CNF-J). Data of pumped flow rate versus delivered pressure, as well as friction loss, are reported for the following conditions: frequencies of 10, 35 and 45 Hz; strokes of 25.4 mm (1.00 in.), 38.1 mm (1.50 in.) and 50.8 mm (2.00 in.) oil inlet temperature of 49 degrees (120 degrees); and pumping ring close-in pressures of 10.3 MPa (1500 lb/square inch. A 20W40 automotive oil was used for all tests. The maximum delivered pressure was 11 MPa (1600 lb/square inch. An analysis of hydrodynamic oil pumping rings was performed and the results of the analysis were compared to measured test data.
Staging method solves problem of friction loss and low efficiency of two phase (liquid/gas) flow in turbines by using high blade-tip speeds in first stage for progressively lower tip speeds in succeeding stages.
The technical feasibility of applying automotive-derived kinematic and free-piston Stirling engine concepts for stationary applications was explored. Automotive-derived engines offer cost advantages by providing a mature and developd engine technology base with downrating and parts commonality options for specific applications. Two engine sizes (30 and 400 kW), two Stirling engine configurations (kinematic and free-piston), and two output systems (crankshaft and hydraulic pump) were studied. The study includes the influences of using either hydrogen or helium as the working gas. The first kinematic configuration selects an existing Stirling engine design from an automotive application and adapts it to stationary requirements. A 50,000-hour life requirement was established by downrating the engine to 40 kW and reducing auxiliary loads. Efficiency improvements were gained by selective material and geometric variations and peak brake efficiency of 36.8 percent using helium gas was achieved. The second design was a four-cylinder, 400 kW engine, utilizing a new output drive system known as the z-crank, which provides lower friction losses and variable stroke power control. Three different material and working gas combinations were considered. Brake efficiency levels varied from 40.5 percent to 45.6 percent. A 37.5 kW single-cycle, free-piston hydraulic output design was generated by scaling one cylinder of the original automotive engine and mating it to a counterbalanced reciprocal hydraulic pump. Metallic diaphragms were utilized to transmit power.
Choked flow rate and pressure profile data were taken on sequential axially alined inlets of the orifice type, with an orifice length-to-diameter ratio of 0.5. The configuration consisted of two to four inlets spaced at 0.66 and 32 orifice diameters apart. At a spacing of 32 diameters the reduced flow rate appeared to follow the simple power-law relation G(sub r)/G(sub r,1) = N (sup-b), where G(sub r,1) is the reduced flow rate for a single inlet, N is the number of inlets, and b, although temperature dependent, is approximately 0.4. At this spacing the instrumented orifices and spacers gave pressure profiles that dropped sharply at the entrance and partially recovered within each inlet, somewhat independent of N. At low inlet temperature jetting through the last orifice was common. At a spacing of 0.66 diameter fluid jetting through all N inlets was prevalent at low temperatures for each configuration studied, as indicated by the flat pressure profiles and flow rates that were nearlly identical to those for a single orifice inlet. A simplifying relation was developed between the friction loss parameters for flow through N sequential tubes and N sequential inlets. The predicted flow rates for N tubes were in reasonable agreement with the N inlet analysis and followed the simple power-law relation.