Search NASA⌕ Search

SEARCH · Search NASA

Results for “gain switching”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Stable CW Single-Frequency Operation of Fabry-Perot Laser Diodes by Self-Injection Phase Locking

Previously, single-frequency semiconductor laser operation using fiber Bragg gratings has been achieved by two methods: 1) use of the FBG as the output coupler for an anti-reflection-coated semiconductor gain element'; 2) pulsed operation of a gain-switched Fabry-Perot laser diode with FBG-optical and RF-electrical feedback. Here, we demonstrate CW single frequency operation from a non-AR coated Fabry-Perot laser diode using only FBG optical feedback. We coupled a nominal 935 run-wavelength Fabry-Perot laser diode to an ultra narrow band (18 pm) FBG. When tuned by varying its temperature, the laser wavelength is pulled toward the centerline of the Bragg grating, and the spectrum of the laser output is seen to fall into three discrete stability regimes as measured by the side-mode suppression ratio.

Duerksen, Gary L.↗
NASA NTRS1999

Stable CW Single Frequency Operation of Fabry-Perot Laser Diodes by Self-Injection Phase Locking

Previously, single-frequency semiconductor laser operation using fiber Bragg gratings has been achieved by tWo methods: 1) use of the FBG as the output coupler for an anti-reflection-coated semiconductor gain element'; 2) pulsed operation of a gain-switched Fabry-Perot laser diode with FBG-optical and RF-electrical feedback'. Here, we demonstrate CW single frequency operation from a non-AR coated Fabry-Perot laser diode using only FBG optical feedback.

Duerksen, Gary L.↗
NASA NTRS2017

Binary polarization-shift-keyed modulation for interplanetary CubeSat optical communications

Recent developments for laser communication on CubeSats across interplanetary distances will be presented. A binary polarization-shift-keyed modulation scheme using dual gain-switched diode lasers is developed and demonstrated within an end-to-end link testbed to achieve signal acquisition under extremely poor signal-to-noise conditions (-43.5 dB average signal-to-noise power ratio at a 1-MHz symbol rate) to simulate direct-to-Earth links, while simultaneously targeting a limited SWaP footprint (1.5U envelope). Additional system design and constraints for the compact laser transmitter will be discussed.

Kovalik, Joseph M.↗
DOE OSTI2022

Novel Quadratic High Gain Boost Converter With Adaptive Soft-Switching Scheme and Reduced Conduction Loss

In this article, an improved soft-switching quadratic boost converter is proposed. Instead of inserting an additional active clamp or auxiliary zero-voltage transition circuit at the switching node, the proposed topology connects the high-voltage switching node to the input diode node by replacing one of the input diodes with a low-rated switch. The proposed topology can attain soft-switching condition for all the switches and input diode turns- off under zero-current switching (ZCS). The operation of input-side switch not only aids zero-voltage switching (ZVS) turn- on for the main switch but also helps in reducing the conduction loss. Also, the input-side switch operates under ZCS turn- on and ZVS turn- off , making it a loss economical solution. An adaptive timing scheme for driving the input switch is proposed, which can ensure soft-switching condition under varying gain and load range. The detailed operational modes, analysis, and design considerations of the proposed topology are presented. A 250 W hardware prototype is built to validate the performance of the proposed converter operating at 100 kHz switching frequency. Results with adaptive soft-switching scheme shows that the converter is modulated to achieve its best efficiency condition under various system conditions. Furthermore, a peak efficiency of 96.1% at 155 W and efficiencies above 95.75% over a wide load range are achieved using all Si devices.

14 SOLAR ENERGY↗
NASA NTRS1967

Review of research and development in fluid logic elements

Research and development in multistate fluid logic elements is reviewed in a historical and critical report. The report concludes that in the development of fluid amplifiers, there are elements with very high gain and poor switching speed, and other elements with very high switching speed and poor gain.

Reader, T.↗
DOE OSTI2025

Mixed gain detector configurations for time-resolved X-ray solution scattering

X-ray detection at X-ray free-electron lasers is challenging in part due to the XFEL's extremely short and intense X-ray pulses. Experimental measurements are further complicated by the large fluctuations inherent to the self-amplified spontaneous emission process producing the X-rays. At the Linac Coherent Light Source the ePix10ka2M detector offers multiple gain modes, and auto-ranging between these, to increase the dynamic range while retaining low noise. For diffuse scattering techniques, such as time-resolved X-ray solution scattering, where the shape of the scattering pattern largely does not change between exposures, a fixed mix of different gain modes offers many of the same advantages as auto-ranging. We find that configuring individual ASICs in separate gain modes does not impact the intensity linearity of the gain response and has a limited effect on the effective dynamic range in regions with different gain mode settings while avoiding the complexities of auto-ranging. Small (<5%) non-linear gain contributions arise when pixels on the same ASIC are configured in different gain modes. We present a configuration scheme that is designed to select the optimal mixed gain configuration to minimize effects of saturation in the high-/medium-gain region, while maximizing the number of pixels with higher gain to improve the signal-to-noise ratio.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Leveraging Cell Expansion Sensing in State of Charge Estimation: Practical Considerations

Measurements such as current and terminal voltage that are typically used to determine the battery’s state of charge (SOC) are augmented with measured force associated with electrode expansion as the lithium intercalates in its structure. The combination of the sensed behavior is shown to improve SOC estimation even for the lithium ion iron phosphate (LFP) chemistry, where the voltage–SOC relation is flat (low slope) making SOC estimation using measured voltage difficult. For the LFP cells, the measured force has a non-monotonic F–SOC relationship. This presents a challenge for estimation as multiple force values can correspond to the same SOC. The traditional linear quadratic estimator can be driven to an incorrect SOC value. To address these difficulties, a novel switching estimation gain is used based on determining the operating region that corresponds to the actual SOC. Moreover, a drift in the measured force associated with a shift of the cell SOC–expansion behavior over time is addressed with a bias estimator for the force signal. The performance of Voltage-based (V) and Voltage and Force-based (V&F) SOC estimation algorithms are then compared and evaluated against a desired ±5% absolute error bound of the SOC using a dynamic stress test current protocol that tests the proposed estimation scheme across wide range of SOC and current rates.

25 ENERGY STORAGE↗
NASA NTRS1978

On-line parameter estimation using a high sensitivity estimator

An on-line parameter identification method is presented. The method is based on a recursive formulation of the maximum likelihood method, with a significant modification on the gains of the state estimator. In the conventional maximum likelihood method, the Kalman gains are used in the state estimator. This produces unbiased, minimum variance parameter estimates in the presence of process noise and measurement noise, but it also slows the convergence rate when the identification is done on-line. Here we suggest choosing the gains to maximize a measure of the sensitivities of the state estimates to parameter variations. One such criterion is to minimize the trace of the inverse information matrix. This increases the convergence rate significantly. After one or two time constants, the gains are switched to the Kalman values to assure unbiased, minimum-variance estimates. The state estimate will initially be nonoptimal, and may not be adequate for control purposes. In this case, a parallel Kalman filter which uses the identifier's parameter estimates can be used. This method is applied here for the identification of a simple first-order system, and for the identification of short-period stability derivatives of an F-8 aircraft from simulated data.

Mishne, D.↗
NASA NTRS1985

Effect of aerodynamic and angle-of-attack uncertainties on the May 1979 entry flight control system of the Space Shuttle from Mach 8 to 1.5

A six degree of freedom simulation analysis was performed for the space shuttle orbiter during entry from Mach 8 to Mach 1.5 with realistic off nominal conditions by using the flight control systems defined by the shuttle contractor. The off nominal conditions included aerodynamic uncertainties in extrapolating from wind tunnel derived characteristics to full scale flight characteristics, uncertainties in the estimates of the reaction control system interaction with the orbiter aerodynamics, an error in deriving the angle of attack from onboard instrumentation, the failure of two of the four reaction control system thrusters on each side, and a lateral center of gravity offset coupled with vehicle and flow asymmetries. With combinations of these off nominal conditions, the flight control system performed satisfactorily. At low hypersonic speeds, a few cases exhibited unacceptable performances when errors in deriving the angle of attack from the onboard instrumentation were modeled. The orbiter was unable to maintain lateral trim for some cases between Mach 5 and Mach 2 and exhibited limit cycle tendencies or residual roll oscillations between Mach 3 and Mach 1. Piloting techniques and changes in some gains and switching times in the flight control system are suggested to help alleviate these problems.

Stone, H. W.↗
NASA NTRS2008

Disabling CNT Electronic Devices by Use of Electron Beams

Bombardment with tightly focused electron beams has been suggested as a means of electrically disabling selected individual carbon-nanotubes (CNTs) in electronic devices. Evidence in support of the suggestion was obtained in an experiment in which a CNT field-effect transistor was disabled (see figure) by focusing a 1-keV electron beam on a CNT that served as the active channel of a field-effect transistor (FET). Such bombardment could be useful in the manufacture of nonvolatile-memory circuits containing CNT FETs. Ultimately, in order to obtain the best electronic performances in CNT FETs and other electronic devices, it will be necessary to fabricate the devices such that each one contains only a single CNT as an active element. At present, this is difficult because there is no way to grow a single CNT at a specific location and with a specific orientation. Instead, the common practice is to build CNTs into electronic devices by relying on spatial distribution to bridge contacts. This practice results in some devices containing no CNTs and some devices containing more than one CNT. Thus, CNT FETs have statistically distributed electronic characteristics (including switching voltages, gains, and mixtures of metallic and semiconducting CNTs). According to the suggestion, by using a 1-keV electron beam (e.g., a beam from a scanning electron microscope), a particular nanotube could be rendered electrically dysfunctional. This procedure could be repeated as many times as necessary on different CNTs in a device until all of the excess CNTs in the device had been disabled, leaving only one CNT as an active element (e.g., as FET channel). The physical mechanism through which a CNT becomes electrically disabled is not yet understood. On one hand, data in the literature show that electron kinetic energy >86 keV is needed to cause displacement damage in a CNT. On the other hand, inasmuch as a 1-keV beam focused on a small spot (typically a few tens of nanometers wide) deposits a significant amount of energy in a small volume, the energy density may suffice to thermally induce structural and/or electronic changes that disable the CNT. Research may be warranted to investigate this effect in detail.

Petkov, Mihail↗
DOE OSTI2022

Generation of nanosecond THz pulses using a high gain ring resonator with a semiconductor switch

A 250 GHz quasi-optical ring resonator consisting of an input coupler and three mirrors has been designed and tested. A low-loss silicon wafer in the ring provides output coupling of the stored power when irradiated by a pulse from a 532 nm laser. The ring created 5.8 ns, 268 mW output power pulses when excited by a 17 mW, 250 GHz continuously operating input source, achieving a power gain of 16. In a fully tuned ring, higher gain is achievable. If the ring was used with a pulsed input source having a pulse length of several times the fill time, the ring could be used as an efficient pulse compressor with similar high gain. The resonator has a wide range of applications, including, at low power, spectroscopy and, at high power, testing of accelerator structures and materials.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Electrical Switching of Nematic Plasmonic Nanocolloids for Infrared Solar Gain Control

Controlling solar gain is essential to reduce the energy consumption by residential and commercial buildings, which are responsible for ≈40% of all energy generated globally. However, the dynamic control of solar gain in the near-infrared that corresponds to ≈50% of the overall Sun's energy at the Earth's surface, separately from the visible spectral range has been a challenge, albeit commercial coatings provide passive control while retaining highly visible transmission. To address this problem, in this paper switchable silver colloids (SSCs) are demonstrated, colloidal analogs of the common silver coatings used for solar gain control. When dispersed in a nematic liquid crystal, orientations of such plasmonic silver nanoplates are controlled by ≈1 V low-voltage electric fields, allowing for sub-second switching of the near-infrared-based solar gain. Installed and retrofit products made from thin films of such nanoplate dispersions confined between glass and plastic substrates, respectively, exhibit electrically controlled infrared-based solar gain while retaining high visible-range transparency, low haze, and high color rendering index. Furthermore, this study's findings reveal a great potential of soft-matter systems in addressing energy-related problems.

36 MATERIALS SCIENCE↗
NASA NTRS1993

Site diversity for satellite earth terminals and measurements at 28 GHz

This paper reviews site diversity concepts and models and presents the results of a site diversity experiment, in which radiometers were used to measure attenuation on earth-space paths, performed at Columbus, Ohio, for a period of one year. Attenuation statistics are presented first in the form of the joint probability density function of attenuation at the two sites. From these are derived the cumulative two-dimensional distribution of attenuation at both sites, the cumulative distribution of attenuation at each site, the effective cumulative distribution of attenuation for a diversity system that always switches to the better of two signals, and the effective cumulative distribution of attenuation for a system with maximal-ratio signal combining. The switched-system diversity gain is compared with Hodge's predictive model, and the diversity improvement is compared with Boithias' model. Fade-duration and interfade-interval statistics are also presented for each site and for systems that employ switching and maximal-ratio combining. Rain-rate and interrainfall interval statistics are also included.

Lin, Kuan-Ting↗
DOE OSTI2020

HarDWR - Raw Water Rights Records

A dataset within the Harmonized Database of Western U.S. Water Rights (HarDWR). For a detailed description of the database, please see the meta-record v2.0. Changelog v2.0 - Switched source data from collecting records from each state independently to using the WestDAAT dataset v1.0 - Initial public release Description In order to hold a water right in the western United States, an entity, (e.g., an individual, corporation, municipality, sovereign government, or non-profit) must register a physical document with the state's water regulatory agency. State water agencies each maintain their own database containing all registered water right documents within the state, along with relevant metadata such as the point of diversion and place of use of the water. All western U.S. states have digitized their individual water rights databases, as well as geospatial data defining the areas in which water rights are managed. Each state maintains and provides their own water rights data in accordance with individual state regulations and standards. In addition, while all states make their water rights publicly available, each provides their records in unique formats, meaning that file types, field availability, and terms vary from state to state. This leads to additional challenges to managing resources which cross state lines, or conducting consistent multi-state water analyses. For the first version of HarDWR, we collected the water rights databases from 11 Western States of the United States. In order to preform regional analyses with the collected data, the raw records had to be harmonized into one single format. The Water Data Exchange (WaDE) is a program dedicated to the sharing of water-related data for the Western U.S. in a singular consistent format. Created by the Western States Water Council (WSWC) to facilitate the collection and dissemination of water data among WSWC's member states and the public, WaDE provides an important service for those interested in water resource planning and management in their focus region. Of the services which WaDE provides, the one of the most interesting is the WestDAAT dataset, which is a collection of water rights data provided by the 18 WSWC member states that have been standardized into a single format, much like we had done on a more limited scale with HarDWR v1. For this version of HarDWR we decided to use WestDAAT, specifically a snapshot created in Feburary 2024, as our water rights source data. A full explanation of the benefits gained from this switch can be found in the description of the updated Harmonized Water Rights Records v2.0, but in short it has allowed us to focus more of our efforts on answering research questions and gaining a more realistic understanding of how water rights are allocated. For more information on how the data for WestDAAT was collected, please see the WaDE data summary. Terms of Use While WaDE works directly with the state agencies to collect and standardize the water rights records, the ultimate authority for the water rights data remains the individual states. Each state, and their respective water right authorities, have made their water right records available for non-commercial reference uses. In addition, the states make no guarantees as to the completeness, accuracy, or timeliness of their respective databases, let alone the modifications which we, the authors of this paper, have made to the collected records. None of the states should be held liable for using this data outside of its intended use. As several of the states update their water rights databases daily, the information provided here is not the latest possible, and should not be used for legal purposes. WestDAAT itself has irregular updates. Additional questions about the data the source states provided should be directed to the respective state agencies (see methods.csv and organization.csv files described below). In addition, although data was presented here was not collected directly from the states, several states requested specifically worked disclaimers when sharing their data. These disclaimers are included here as an acknowledgement from where the water rights data is primarily sourced. Colorado: "The data made available here has been modified for use from its original source, which is the State of Colorado. THE STATE OF COLORADO MAKES NO REPRESENTATIONS OR WARRANTY AS TO THE COMPLETENESS, ACCURACY, TIMELINESS, OR CONTENT OF ANY DATA MADE AVAILABLE THROUGH THIS SITE. THE STATE OF COLORADO EXPRESSLY DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE. The data is subject to change as modifications and updates are complete. It is understood that the information contained in the Web feed is being used at one's own risk." Montana: "The Montana State Library provides this product/service for informational purposes only. The Library did not produce it for, nor is it suitable for legal, engineering, or surveying purposes. Consumers of this information should review or consult the primary data and information sources to ascertain the viability of the information for their purposes. The Library provides these data in good faith but does not represent or warrant its accuracy, adequacy, or completeness. In no event shall the Library be liable for any incorrect results or analysis; any direct, indirect, special, or consequential damages to any party; or any lost profits arising out of or in connection with the use or the inability to use the data or the services provided. The Library makes these data and services available as a convenience to the public, and for no other purpose. The Library reserves the right to change or revise published data and/or services at any time." Oregon: "This product is for informational purposes and may not have been prepared for, or be suitable for legal, engineering, or surveying purposes. Users of this information should review or consult the primary data and information sources to ascertain the usability of the information." File Descriptions The unmodified February, 2024 WestDAAT snapshot is composed of nine files. Below is a brief description of each file, as well as how they were utilized for HarDWR. WaDEDataDictionaryTerms.xlsx: As the file's name implies, this is a data dictionary for all of the below named files. This file describes the column names for each of the following files, with the exception of citation.txt which does not have any columns. The descriptions for each file are divided by tab,with the same name as their associated file, within this document. allocationamount.csv: The "main" file of the group, it contains the water right records for each state. Of particular note, each water right is broken down into one or more water allocations. Allocations may be withdrawn from one or more locations, or even multiple allocations associated with a particular location. This is a more subtle and realistic representation of how water is used than what was available in the first version of HarDWR. For the records from some states, this can mean that multiple allocations listed under a single right will appear as rows within this file. citation.txt: A combination of contact information for WaDE personnel, disclaimer about how the data should be used, and guidelines for citing WestDAAT. methods.csv: A file describing the source and method by which WaDE collected water rights data from each state. organization.csv: A file listing the water rights authoritative agencies for each state. sites.csv: This file provides the geographic, and other descriptors, of the physical location of allocations, called 'sites'. To reiterate, it is possible for one allocation to be associated with multiple sites, as well as one site to be associated with multiple allocations. The two descriptors which we were most interested in where the site's coordinates, as well as whether the site was classified as a Point of Diversion (POD) or a Place of Use (POU). As a general rule, PODs are geographic points, while POUs are areas typically represented as property boundaries or irregularly shaped polygons. sites_pouGeometry.csv: For those allocations with a POU site, this file contains the defining points for the associated polygons. variables.csv: A file describing the units in which an allocation's water amount is reported within WestDAAT. This information is essentially a repeat of the 'AllocationFlow_CFS' and 'AllocationVolume_AF' columns within allocationamount.csv, at least for our purposes. watersources: This file describes the source of water from which each site extracts from. For our purposes, this table was used to determine whether the water came from Surface Water, Groundwater, or Unspecified Water.

Lisk, Matthew↗
NASA NTRS1995

Circuit Stops Prelasing In A Q-Switched Laser

Protective shutdown circuit stops prelasing in Q-switched laser operating at pulse-repetition rate of about 10 Hz. During normal operation, Q-switch prevents emission of light from laser cavity during application of Q-switch-trigger pulse. When circuit detects prelasing, it triggers relay turning off laser power supply. Circuit integrated into almost any Q-switched-laser system, provided one gains access to laser light, Q-switch-trigger pulse, and safety-interlock line of laser power supply.

Lockard, George E.↗