SEARCH · Search NASA

Results for “gas nitriding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Concepts for Actinide Recovery from TRISO Used Nuclear Fuel

The work described in this report has developed a preliminary conceptual flowsheet based on limited published literature for the head-end of a TRISO oxycarbide UNF reprocessing plant. The essential function of the head-end is to prepare the UNF for subsequent separation of actinides. The main steps of the conceptual TRISO UNF head-end reprocessing flowsheet are: 1. Fragmentation of the graphite moderator to expose the fuel particles. 2. Separation of fuel particles from fragmented graphite moderator by sieving and fluidization. 3. Fragmentation of the fuel particles to expose the fuel kernel. 4. Dissolution of the fuel kernel in nitric acid. Noteworthy at this step is the formation of organic acids (mainly oxalic and mellitic acids) from the carbon associated with the fuel and TRISO coatings. These acids can interfere with actinide separations and solvent extraction hydraulic performance and carbon dioxide gas generation. 5. Clarification of the dissolved fuel solution to separate the coating fragments. 6. Dissolver off-gas treatment with specific emphasis on managing generation of carbon dioxide gas containing carbon-14. The quantity of carbon dioxide is projected to be 100 to 1000 times greater than that arising from dissolving LWR UNF. Pre or post treatment of the exposed fuel kernels could be undertaken to mitigate the formation of organic acids but there still exists a significant off-gas treatment challenge. The literature on reprocessing uranium nitride UNF was reviewed but a flowsheet was not specifically developed since its scope and uncertainties are expected to be encompassed by the oxycarbide flowsheet. Overall, the predominant feature of processing TRISO UNF is carbon management to reduce waste volume and mitigate the formation of carbon dioxide and organic acids. This report recommends broad areas of research that will help to further define the head-end flowsheet.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Cesium intercalation of graphene: A 2D protective layer on alkali antimonide photocathode

Alkali antimonide photocathodes have wide applications in free-electron lasers and electron cooling. The short lifetime of alkali antimonide photocathodes necessitates frequent replacement of the photocathodes during a beam operation. Furthermore, exposure to mediocre vacuum causes loss of photocathode quantum efficiency due to the chemical reaction with residual gas molecules. Theoretical analyses have shown that covering an alkali antimonide photocathode with a monolayer graphene or hexagonal boron nitride protects it in a coarse vacuum environment due to the inhibition of chemical reactions with residual gas molecules. Alkali antimonide photocathodes require an ultra-high vacuum environment, and depositing a monolayer 2D material on it poses a serious challenge. In the present work, we have incorporated a novel method known as intercalation, in which alkali atoms pass through the defects of a graphene thin film to create a photocathode material underneath. Initially, Sb was deposited on a Si substrate, and a monolayer graphene was transferred on top of the Sb film. Heat cleaning around 550–600 °C effectively removed the Sb oxides, leaving metallic Sb underneath the graphene layer. Depositing Cs on top of a monolayer graphene enabled the intercalation process. Atomic force microscopy, Raman spectroscopy, x-ray photoelectron spectroscopy, low energy electron microscopy, and x-ray diffraction measurements were performed to evaluate photocathode formation underneath the monolayer graphene. Our analysis shows that Cs penetrated the graphene and reacted with Sb and formed Cs 3 Sb.

2D materials↗

DOE OSTI2020

Transition Metal Nitrides as Promising Catalyst Supports for Tuning CO/H 2 Syngas Production from Electrochemical CO 2 Reduction

The electrochemical carbon dioxide reduction reaction (CO 2 RR) to produce synthesis gas (syngas) with tunable CO/H 2 ratios has been studied by supporting Pd catalysts on transition metal nitride (TMN) substrates. Combining experimental measurements and density functional theory (DFT) calculations, Pd-modified niobium nitride (Pd/NbN) is found to generate much higher CO and H 2 partial current densities and greater CO Faradaic efficiency than Pd-modified vanadium nitride (Pd/VN) and commercial Pd/C catalysts. In-situ X-ray diffraction identifies the formation of PdH in Pd/NbN and Pd/C under CO 2 RR conditions, whereas the Pd in Pd/VN is not fully transformed into the active PdH phase. DFT calculations show that the stabilized *HOCO and weakened *CO intermediates on PdH/NbN are critical to achieving higher CO 2 RR activity. This work suggests that NbN is a promising substrate to modify Pd, resulting in an enhanced electrochemical conversion of CO 2 to syngas with a potential reduction in precious metal loading.

25 ENERGY STORAGE↗

DOE OSTI2020

In situ characterization of foreign object damage (FOD) in environmental-barrier-coated silicon carbide (SiC) ceramic

Environmental barrier coatings (EBCs) protect advanced ceramics and ceramic matrix composites (CMCs) from oxidation and corrosion in gas turbine engine environments. Foreign object damage (FOD), where debris impact the protective coatings, is a critical hazard which limits the turbine durability. Despite previous efforts to understand FOD in EBCs, a detailed understanding of the fundamental transient damage mechanisms is still lacking. In the current work, the real-time FOD behavior of a Mullite / Silicon EBC was visualized via a dynamic synchrotron X-ray source in phase contrast imaging (PCI) configuration. Prior to the in situ FOD experiments, the microstructure and composition of the coating were respectively characterized using a scanning electron microscope (SEM) and X-ray diffraction (XRD). The variation in the properties of the debris was modeled by ~ 1.5 mm diameter Partially Stabilized Zirconia (PSZ) and Silicon Nitride (Si 3 N 4 ) spheres. A modified light-gas gun setup, synchronized with the X-ray beam, was used to propel the projectiles at velocities ranging between 300 and 355 m·s -1 . Coated samples were impacted under a fully backed support configuration and at normal incidence. Coating penetration and delamination, as well as projectile deformation at the bond coat resulted for FOD by PSZ spheres. Comparatively, projectile fracture, with subsequent rebound of fragments, as well as complete coating penetration and delamination at the substrate interface occurred for FOD by Si 3 N 4 spheres. It should be noted that only cone cracking was observed for FOD by PSZ spheres while back surface cracking was present for both projectile types. Qualitative understanding of the driving forces for the observed damage mechanisms were provided.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Mitigation of Pitting on Nitrogen-Doped Niobium Surfaces through Two-Step Electropolishing

Surface processing of niobium superconducting RF cavities used in particle accelerators is crucial for determining their performance. The nitrogen (N)-doping method, developed at Fermilab, enhances the cavities’ quality factor by doping the cavity’s interior surface with N atoms at 800 °C. After N-doping, electropolishing (EP) is employed to remove the niobium nitride phases and attain the desired concentration of interstitial N atoms. This study explores the effects of EP conditions on N-doped niobium samples. The samples were electropolished at 5 to 40 °C and voltages between 3 and 22 V. Different EP voltage ranges produced two types of pits, classified based on their sizes. Larger pits, linked to higher voltages, are also affected by the reaction rate. Pitting could be reduced at a lower temperature and adequate EP voltage. However, to effectively minimize gas evolution forming large-sized pitting, peeling off the top nitride layer before EP might be beneficial. This was achieved through precise low-voltage etching, forming a two-step EP process. The process involves removing the top 100–200 nm layer at a low voltage, followed by standard EP to remove the required material. This two-step EP process effectively mitigated the pitting risk associated with gas evolution on N-doped surfaces.

43 PARTICLE ACCELERATORS↗

DOE OSTI2020

Transition Metal Nitrides as Promising Catalyst Supports for Tuning CO/H[subscript 2] Syngas Production from Electrochemical CO[subscript 2] Reduction

Abstract not provided

Liu, Yumeng↗

DOE OSTI2024

Resistance of Boron Nitride Nanotubes to Radiation-Induced Oxidation

We present unprecedented results on the damage thresholds and pathways for boron nitride nanotubes (BNNT) under the influence of energetic electrons in an oxidative gas environment, using an environmental aberration-corrected electron microscope over a range of oxygen pressures. We observe a damage cascade process that resists damage until a higher electron dose, compared with carbon nanotubes, initiating at defect-free BNNT sidewalls and proceeding through the conversion from crystalline nanotubes to amorphous boron nitride (BN), resisting oxidation throughout. We compare with prior results on the oxidation of carbon nanotubes and present a model that attributes the onset of damage in both cases to a physisorbed oxygen layer that reduces the threshold for damage onset. Surprisingly, increased temperatures offer protection against damage, as do electron dose rates that significantly exceed the oxygen dose rates, and our model attributes both effects to a physisorbed oxygen population.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Dataset for "Resistance of Boron Nitride Nanotubes to Radiation-Induced Oxidation" as published in The Journal of Physical Chemistry C

Adsorption↗

DOE OSTI2025

Encapsulation of Monolayer 2D Materials Using Kinetic Energy-Controlled Pulsed Laser Deposition

The integration of monolayer (ML) two-dimensional (2D) materials into next-generation microelectronics, optoelectronics, and sensors is hindered by their sensitivity to environmental exposure. Deposition of additional layers for encapsulation or growth on ML 2D materials by versatile but energetic plasma techniques such as pulsed laser deposition (PLD) has not been considered at the monolayer level because of potential damage caused by hyperthermal species with kinetic energies (KEs) exceeding the threshold displacement energy (TDE) of the ML. Here, we describe a general strategy to understand and mitigate damage during PLD by reducing the incident KE of ablated species below the TDE of the 2D monolayer using background gas collisions. Ion flux diagnostics, combined with in situ Raman spectroscopy of monolayer graphene during PLD of amorphous boron nitride (a-BN) as a dielectric encapsulation layer, show that damage is primarily correlated with fast ions that penetrate the background gas in accordance with Beer’s Law and are often overlooked in ICCD imaging due to the dominance of the bright, delayed plasma luminescence. Significantly, if fast ions are eliminated and a ∼2 nm-thick a-BN layer is “soft landed”, the monolayer graphene is effectively protected from damage by high KE species in the boron nitride plasma plume. Deposited a-BN films display a characteristic dielectric constant of 3.6 at 100 kHz and tunable charge injection properties. Our results enable PLD as a viable option for encapsulation and thin film growth onto ML 2D materials, with implications for both fundamental research and device integration.

2D materials↗

DOE OSTI2022

Hydrogen Crossover Flux through Two-Dimensional Nanomaterials

Energy storage and conversion devices require an ion-exchange membrane with high transmission of charge-balancing ions and separation of anode and cathode electrolytes/gases. This ensures optimum device performance. Most conventional membranes suffer huge cross-permeation resulting in low energy efficiency and material degradation. This work investigated hydrogen permeability and proton transmission through membrane electrode assemblies (MEAs) containing a monolayer of hexagonal boron nitride and single-layer and bi-layer graphene in a gas-phase small-scale cell and a liquid cell. Here we found that the hydrogen crossover flux through MEAs with 2D materials was inhibited by at least a factor of 5 compared to the one without. Single-layer graphene and boron nitride enabled high proton transmission, but bi-layer graphene inhibited proton conduction. Defect visualization of 2D materials revealed few atomic-scale defects in graphene. These findings suggest that a monolayer of 2D material may provide good selectivity for energy conversion and storage devices by blocking species crossover while allowing high proton transmission.

2D materials↗

DOE OSTI2023

Hydrogen Sulfide Passivation for p-Type Passivated Emitter and Rear Contact Solar Cells

This work reports on the application of sulfur (S)-passivation to passivated emitter and rear contact (PERC) solar cells. The emitter surface was passivated by hydrogen sulfide (H 2 S) gas phase reaction and capped by a hydrogenated amorphous silicon nitride (a-SiN x :H) layer. The sulfur passivation on a symmetrically n + diffused emitter is shown to lead to an emitter saturation current density (J 0n+ ) of 30 fA/cm 2 at R sheet,n+ ≈ 100 Ω/sq. The application of S-passivation to the emitter surface in the PERC cell structure, with the rear surface passivated by an aluminum oxide (Al 2 O 3 )/a-SiN x :H stack, showed a promising implied open-circuit voltage (iV OC ) of 686 mV before metallization. This iV OC was higher than that for the a-SiN x :H or SiO 2 /a-SiN x :H passivated emitter surfaces (675 and 674 mV, respectively) on PERC cells processed in the same run. However, a significant drop in cell V OC is observed for the S-passivated PERC cell after the completion of device fabrication with laser patterning, screen-printed metal contact deposition, and firing. Nonetheless, an efficiency of ~20% and a V OC of ~650 mV was achieved with an emitter surface passivated by sulfur. We identified that the 760°C contact firing process degrades the S-passivation quality. Furthermore, the surface morphology was studied, and a detailed surface analysis was performed to study the causes of the S-passivated surface degradation.

14 SOLAR ENERGY↗

DOE OSTI2025

Probing the Surface Chemistry of Lithium Nitridation

Chemical synthesis of Li 3 N through lithium nitridation has potential to advance rechargeable battery and nitrogen fixation technology. However, studies of the conditions for forming Li 3 N on the lithium surface via nitrogen gas exposure report contradictory findings, such as the spontaneous reaction of Li with pure N 2 , the impossibility of forming Li 3 N through pure Li and N 2 interaction, the requirement of trace H 2 O to catalyze the reaction, and evidence to the contrary. In this study, ambient pressure X-ray photoelectron spectroscopy (APXPS) was applied to evaluate the in situ chemical evolution of the lithium metal surface under nitrogen gas up to 800 mTorr. At pressures ≤10 mTorr, no Li 3 N was detected. At higher pressures, surface Li 3 N rapidly reacts with trace CO 2 . Additionally, because metallic lithium is readily oxidized by trace gases, the atomic nitrogen concentration of the lithium surface remains below 2%. When nitridation follows oxidation by O 2 gas, CO 2 gas, or H 2 O vapor, surface Li 3 N formation is inhibited. These results suggest that nitrogen gas can diffuse through the oxidized lithium metal surface to react with subsurface metallic lithium.

Binding energy↗

DOE OSTI2020

Ammonia Permeation Through Inorganic Membranes

Moisture probes are used in the tritium facility to measure the moisture content of the gas stream. When tritium reacts with nitrogen to form ammonia, the ammonia gas damages the sensitive moisture probe. The gas stream tested during this experiment for moisture probe protection is composed of nitrogen and argon gas in conjunction with ammonia and water vapor. The gas stream is filtered through an inorganic membrane due to the high reactivity of tritium and a residual gas analyzer (RGA) is used to measure the ammonia and water vapor in the gas stream, as well as the permeability of nitrogen and argon through the inorganic membranes. The membranes tested were boron nitride and silver. The permeability was compared for each membrane at different pressures and flow rates. Fourier-transformed infrared spectroscopy (FT-IR) was used to compare the membranes before and after ammonia permeation. Ammonia gas is a byproduct formed from tritium gas reacting with nitrogen in the gas stream, similar to the Haber Process which occurs when hydrogen reacts with nitrogen [2]. The corrosive nature of ammonia damages metals and sensitive instruments such as moisture probes. Moisture probes are essential in various gas and liquid processes for measuring the moisture content of a gas. Membrane research has found that graphene oxide membranes successfully uptake ammonia from the gas stream at a humidity of approximately 30% at which point the pores pin closed, preventing gas permeation. Further research is being conducted to find an inorganic membrane that will prevent ammonia permeation thus circumventing damage to the sensitive moisture probe. The permeation measurements for argon and nitrogen gas and water and ammonia vapor were measured at various pressures of 800, 1000, 1200, 1500, 1800, and 2000 torr. The permeability average (PA) was calculated for each filter using a Barrer calculation. The average permeations for each filter were then compared. The gas composition was measured using the RGA Nitrogen was permeated through the membranes after ammonia permeation and a FT-IR spectrum was obtained. Boron Nitride: As the nitrogen pressure increased, the permeability of the membrane decreased from 800-1200 torr and remained relatively unchanged from 1200-2000 torr. The membrane exhibited a slight decrease in argon permeability from 800-1200 torr and a slight increase from 1500-2000 torr. The boron nitride membrane when permeated with ammonia and nitrogen prevented less ammonia permeation compared to the blank filter. The boron nitride filter demonstrated a decrease in permeability after ammonia permeation. Silver Membrane: When permeated with nitrogen alone, the membrane permeability decreased from 800 torr to 1200 torr. The permeability of the membrane showed little difference as pressure increased from 1200 torr. When permeated with argon, the same phenomenon occurred but on a much smaller scale. When compared to the blank and the boron nitride membranes the silver membrane exhibited significantly lower permeability. This may be in part due to the coating on the silver membrane and differences in pore size of the membranes. During permeation with ammonium hydroxide vapor and nitrogen, the partial pressure of the ammonia increased as compared to the blank membrane. The permeability before and after permeation with ammonia and nitrogen were compared. Permeability values suggested that after being permeated with the ammonia that the permeability for lower pressures increased slightly. There was no significant change in the FT-IR spectrums before and after permeation. Future work: Continue testing various inorganic membranes for ammonia permeation. Further research chemical separation of ammonia from the gas stream, which may prove difficult due to the high reactivity of tritium.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Fabrication of uranium nitride

A method of producing uranium nitride (e.g., uranium mononitride) and/or uranium-containing intermediates that can be used to further produce uranium nitride includes reacting a reaction mixture comprising uranium carbide with a gas comprising hydrogen and nitrogen, cooling the reaction mixture to a temperature suitable to produce a phase comprising U2N3, and heating the reaction mixture to a temperature suitable to convert the phase comprising U2N3 to a phase comprising UN. The method produces highly purified UN, is insensitive to excess carbon reactants, and can be readily integrated into existing uranium production facilities as part of a continuous process.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

DOE OSTI2022

Partial oxidation of methane to methanol on boron nitride at near critical acetonitrile

Abstract Direct catalytic conversion of methane to methanol with O 2 has been a fundamental challenge in unlocking abundant natural gas supplies. Metal-free methane conversion with 17% methanol yield based on the limiting reagent O 2 at 275 °C was achieved with near supercritical acetonitrile in the presence of boron nitride. Reaction temperature, catalyst loading, dwell time, methane–oxygen molar ratio, and solvent-oxygen molar ratios were identified as critical factors controlling methane activation and the methanol yield. Extension of the study to ethane (C2) showed moderate yields of methanol (3.6%) and ethanol (4.5%).

03 NATURAL GAS↗

DOE OSTI2025

Steam-Assisted Ammonolysis of MoO2 as a Synthetic Pathway to Oxygenated δ-MoN

A common route for the synthesis of molybdenum nitrides is through the temperature-programmed reaction of molybdenum oxides with NH3, or ammonolysis. In this work, the role of precursor phase, gas phase chemistry (impact of H2O), and temperature profile on the reaction outcome (700 °C) was examined, which resulted in varying amounts of MoO2, H2MoO5, and the nitride phases—cubic γ (nominally Mo2N) and hexagonal δ (nominally MoN). The phase fraction of the δ phase increased with precursor in the sequence MoO2 > MoO3 > H2MoO5. Steam in the reaction gas also favored the production of δ over γ, but with too much steam, MoO2 was obtained in the product. Synthesis conditions for obtaining nearly phase-pure δ were identified: MoO2 as the precursor, 2% H2O in the gas stream, and a moderate heating rate (3 °C/min). In situ X-ray diffraction provided insights into the reaction pathway. Extensive physico-chemical analysis of the δ phase, including synchrotron X-ray and neutron diffraction, electron microscopy, thermogravimetric analysis, X-ray photoelectron spectroscopy, and prompt gamma activation analysis, revealed its stoichiometry to be MoO0.108(8)N0.892(8)H0.012(5), indicating non-trivial oxygen incorporation. The presence of N/O ordering and an impurity phase Mo5N6 were also revealed, detectable only by neutron diffraction. Notably, a computationally predicted MoON phase (doi: 10.1103/PhysRevLett.123.236402), of interest due to its potential to display a metal-insulator transition, did not appear under any reaction condition examined.

Pandey, Shobhit↗

DOE OSTI2022

System and methods for fabricating boron nitride nanostructures

This disclosure provides systems, methods, and apparatus related to boron nitride nanomaterials. In one aspect, a method includes generating a directed flow of plasma. A boron-containing species is introduced to the directed flow of the plasma. Boron nitride nanostructures are formed in a chamber. In another aspect, a method includes generating a directed flow of plasma using nitrogen gas. A boron-containing species is introduced to the directed flow of the plasma. The boron-containing species can consist of boron powder, boron nitride powder, and/or boron oxide powder. Boron nitride nanostructures are formed in a chamber, with a pressure in the chamber being about 3 atmospheres or greater.

Fathalizadeh, Aidin↗

DOE OSTI2022

Coolant Channel Design for Additively Manufactured Reactor Cores

Additive manufacturing (AM) methods are currently being explored for applications in nuclear reactors to make advanced reactors more efficient, safe, and reliable. The Transformational Challenge Reactor (TCR) program has explored AM for nuclear by designing a high-temperature gas reactor (HTGR) using an AM silicon carbide fuel form with uranium nitride–tristructural isotropic fuel. In this study, we detail the design process for the TCR fuel form’s coolant channels using computational fluid dynamics models with conjugate heat transfer. Additionally, this work discusses how these models were interfaced with other design teams, project milestones, and the agile design method used to mature the reactor design. The methodology deployed was able to create a channel design with lower maximum fuel temperatures and thermal stresses in the fuel form over traditional channel designs that can be manufactured subtractively. These results were achieved with only small manufacturing penalties. Results are discussed and presented on lessons learned for designing AM components for nuclear reactors. Finally, areas of opportunity are discussed for advanced design tools to further automate design activities and optimize reactors with fewer built-in assumptions.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗