Search NASA⌕ Search

SEARCH · Search NASA

Results for “granular biomass materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

27 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Flowability of Crumbler Rotary Shear Size-Reduced Granular Biomass: An Experiment-Informed Modeling Study on the Angle of Repose

Biomass has potential as a carbon-neutral alternative to petroleum for chemical and energy products. However, complete replacement of fossil fuel is contingent upon efficient processes to eliminate undesirable characteristics of biomass, e.g., low bulk density, variability, and storage-induced quality problems. Mechanical size reduction via comminution is a processing operation to engineer favorable biomass flowability in handling. Crumbler rotary shear mill has been empirically demonstrated to produce more uniformly shaped particles with higher flowability than hammermilled biomass. This study combines modeling and experimentation to unveil fundamental understandings of the relation between granular particle characteristics and biomass flow behavior, which elucidate underlying mechanisms and guide selection of critical processing parameters. For this purpose, the impact of critical material attributes, including particle size (2–6 mm), particle shape (briquette, chip, clumped-sphere, cube, etc.), and surface roughness, on the angle of repose (AOR) of milled pine chips were investigated using discrete element method (DEM) simulations. Forest Concepts Crumbler rotary shear system is used to produce milled pine particles within the same size range considered in DEM simulations. AOR of different sets of these particles were measured experimentally to benchmark DEM results against experimental data. Specific energy consumption for the comminution of biomass with different particle size and moisture content are measured for technoeconomic analysis. Our results show that the smaller size (2 mm) of pine particle achieves better followability (i.e., smaller AOR) while the energy cost of comminution is significantly higher and bulk density is almost the same as the 6-mm pine particles. For the 2-mm particle size, Crumbles from veneer have better flow properties than Crumbles from chips. Contrarily, no significant difference was observed between the AOR of the two materials for the 6-mm particle size. Furthermore, from DEM simulations, mechanical interlocking between particles was found as a dominant factor in determining AOR of complex-shaped particles such as milled pine, which cannot be accurately captured by using simple particle shapes (e.g., mono-sphere) with a rolling resistance model. Conversely, clumped-sphere model alleviates this limitation without increasing computational cost significantly and can be used for accurate representation of biomass granular particles when simulating free-flow behavior.

09 BIOMASS FUELS↗
DOE OSTI2023

Particle size and shape effect of Crumbler® rotary shear-milled granular woody biomass on the performance of Acrison® screw feeder: A computational and experimental investigation

Physical experiments and discrete element model (DEM) simulations are conducted to evaluate particle characteristics and operation parameter effects on screw feeding performance for rotary shear-milled Douglas fir. Three performance metrics are used: mass flow rate, shaft driving torque, and specific energy consumption. The impact of particle size, particle size distribution (PSD), shaft rotational speed (rpm), and hopper dimensions on the performance are investigated. All employed performance metrics reveal the superior flowability of the 2-mm particles in contrast to the larger 6-mm counterpart. Remarkably, wider PSD results in poorer flowability than the two mono-sized particles, proving the flowability enhancement achieved by narrower PSD of the woody feedstock. More importantly, DEM simulations unveil PSD-induced degradation in flowability is attributed to mechanical interlocking and particle segregation effects. Furthermore, higher shaft rpm causes higher mass flow rate at the cost of higher specific energy consumption due to viscous dissipation and changes in flow pattern.

09 BIOMASS FUELS↗
DOE OSTI2025

Enhancing biomass flowability for entrained flow Gasification: The role of densification and torrefaction

Gasification presents a key strategy in addressing future energy demands while minimizing environmental impact. This has been recognized as a promising method to convert biomass to higher value products such as biofuels or hydrogen. Among gasification technologies, high-temperature and high-pressure reactors, particularly the R-GAS® system, emerge as an advanced option boasting superior conversion efficiency. However, akin to conventional high-temperature and high-pressure gasifiers, R-GAS® necessitates small particle sizes for optimal carbon conversion, a requirement yet to be fully explored for biomass. Hence, this study investigated the effectiveness of combined mechanical and thermal preprocessing techniques in modifying the physicochemical properties of biomass to suit gasification systems. Mechanical techniques including densification and pulverization, alongside thermal techniques such as torrefaction and steam explosion, were examined. The results demonstrate that torrefaction fosters producing of uniform granular material, enhancing flowability and reducing energy requirements for pulverization compared to steam explosion. Notably, torrefied corn stover exhibited lower internal friction angles and effective cohesion (40.09 ± 0.22° and 0.56 ± 0.01 kPa, respectively) compared to steam exploded corn stover (41.87 ± 0.65° and 0.83 ± 0.06 kPa, respectively), indicative of improved flowability. Additionally, pulverization of torrefied corn stover required approximately 16 % less energy than steam exploded corn stover and 91 % less energy than raw corn stover. Furthermore, the torrefaction-induced alterations in particle size, shape, and packing densities emphasize its potential to optimize flow and handling processes for gasification. These findings underline that densification followed by torrefaction effectively addresses biomass variability, leading to more efficient and sustainable energy conversion.

09 - BIOMASS FUELS↗
DOE OSTI2022

Multiscale Shear Properties and Flow Performance of Milled Woody Biomass

One dominant challenge facing the development of biorefineries is achieving consistent system throughput with highly variant biomass feedstock quality and handling performance. Current handling unit operations are adapted from other sectors (primarily agriculture), where some simplifying assumptions about granular mechanics and flow performance do not translate well to a highly compressible and anisotropic material with nonlinear time- and stress-dependent properties. This work explores the shear and frictional properties of loblolly pine at multiple experimental test apparatus and particle scales to elucidate a property window that defines the shear behavior over a range of material attributes (particle size, size distribution, moisture content, etc.). In general, it was observed that the bulk internal friction and apparent cohesion depend strongly on both the stress state of the sample in granular shear testers and the overall particle size and distribution span. For equipment designed to characterize the quasi-static shear stress failure of bulk materials ranging from 50 to 1,000 ml in test volume, similar test results were observed for finely milled particles (50% passing size of 1.4 mm) with a narrow size distribution (span between 10 and 90% passing size of 0.9 mm), while stress chaining and over-torque issues persisted for the bench-scale test apparatus for larger particle sizes or widely dispersed sample sizes. Measurement of the anisotropic particle–particle friction ranged from coefficients of approximately 0.20 to 0.45 and resulted in significantly higher and more variable friction measurements for larger particle sizes and in perpendicular alignment orientations. To supplement these laboratory-scale properties, this work explores the flow of loblolly pine and Douglas fir through a pilot-scale wedge-shaped hopper and a screw feeder. For the gravity-driven hopper flow, the critical arching distance and mass discharge rate ranged from approximately 10 to 30 mm and 2 to 16 tons/hour, respectively, for both materials, where the arching distance depends strongly on the overall particle size and depends less on the hopper inclination angle. Comparatively, the auger feeder was found to be much more impacted by the size of the particles, where smaller particles had a more consistent and stable flow while consuming less power.

09 BIOMASS FUELS↗
NASA NTRS2003

Assessment of Models of Chemically Reacting Granular Flows

A report presents an assessment of a general mathematical model of dense, chemically reacting granular flows like those in fluidized beds used to pyrolize biomass. The model incorporates submodels that have been described in several NASA Tech Briefs articles, including "Generalized Mathematical Model of Pyrolysis of Biomass" (NPO-20068) NASA Tech Briefs, Vol. 22, No. 2 (February 1998), page 60; "Model of Pyrolysis of Biomass in a Fluidized-Bed Reactor" (NPO-20708), NASA Tech Briefs, Vol. 25, No. 6 (June 2001), page 59; and "Model of Fluidized Bed Containing Reacting Solids and Gases" (NPO- 30163), which appears elsewhere in this issue. The model was used to perform computational simulations in a test case of pyrolysis in a reactor containing sand and biomass (i.e., plant material) particles through which passes a flow of hot nitrogen. The boundary conditions and other parameters were selected for the test case to enable assessment of the validity of some assumptions incorporated into submodels of granular stresses, granular thermal conductivity, and heating of particles. The results of the simulation are interpreted as partly affirming the assumptions in some respects and indicating the need for refinements of the assumptions and the affected submodels in other respects.

Bellan, Josette↗
DOE OSTI2023

Smart Preprocessing & Robust Integration Emulator

To achieve the desired particle size of biomass feedstocks during preprocessing for trouble-free handling and conversion to produce biofuels and bioproducts, the raw materials must undergo a crucial milling process. The particle size of biomass plays a critical role in subsequent biofuel manufacturing, where a larger area-to-volume ratio facilitates efficient synthesis while balancing the impact of moisture on biomass storage. To optimize biofuel production efficiency and overcome these challenges, it is imperative to accurately predict the particle size distribution (PSD) of the biomass in the design of efficient preprocessing systems. The population balance model (PBM), upon empirical calibration and validation, can provide rapid prediction of post-milling PSD of granular biomass. However, PSD has limitations related to mass conservation and the absence of moisture considerations. To overcome these drawbacks, a deep learning model called the enhanced deep neural operator (DNO+) is implemented in the code. This model not only retains the capabilities of the PBM in handling complex mapping functions but also incorporates additional factors influencing the system. By considering various experimental conditions such as sieve size and moisture content, the trained DNO+ model can effectively predict the PSD after milling for any given feed PSD. To further reduce the reliance on experimental data, the PBM is integrated into the DNO+ model, resulting in a physics-informed DNO+ (PIDNO+). The PIDNO+ model addresses the non-conservation of quality exhibited by the PBM while inheriting the advantages of the DNO+ model in considering multiple influencing factors. Moreover, the PIDNO+ model significantly reduces the amount of data required for model training. Both deep learning models, i.e., DNO+ and PIDNO+, are excellent in predictive performance, offering swift and accurate machine learning-based predictions. The use of this code that contains these models will assist in guiding the proper milling equipment selection and operational conditions to achieve the desired biomass particle sizes, ensuring the efficiency of subsequent biofuel and bioproduct production processes.

Xia, Yidong [Idaho National Laboratory (INL), Idah↗
DOE OSTI2022

Predictive models enhance feedstock quality of corn stover via air classification

Feedstock heterogeneity is a fundamental obstacle to cost-competitive biobased products. Agricultural products like corn stover have anatomical components that vary in their chemical composition, mechanical properties, structure, and response to chemical and biological treatments. A technique that can enrich streams in select anatomical fractions would allow a tailored deconstruction approach to increase overall process efficiency. Air classification can be leveraged for such refining, however, fundamental characterization and understanding of the particle properties that underly the physics of air classification are only modestly documented. Here, we determine fundamental particle properties including mass-to-area ratio, drag coefficient, and partition velocity that describe how anatomical tissues of corn stover behave during air classification. In this work, mass-to-area ratios of anatomical tissues vary by nearly two orders of magnitude from 2.3 mg/mm 2 for cob to 0.04 mg/mm 2 for leaf. Drag coefficients of longer, fibrous materials (i.e., rind, husk, and sheath) are shown to correlate with particle area (p-value < 0.001) whereas granular tissues (i.e., cob, pith, and leaf) correlate better with mass-to-area ratio (p-values < 0.001). When compared to experimental observations, a simulated two-stage air classification and size reduction scenario predicts the overall partitioning of anatomical tissues within 15% for pith, husk, rind, and cob tissues. The model predicts an air-classified fraction preferentially enriched in cob (purity = 20%), rind (purity = 74%), and pith (purity = 4.5%) with a mass yield of 47%. Empirical relations for these properties can be used to predict the partitioning of corn stover during air classification based on anatomical type and size.

09 BIOMASS FUELS↗
DOE OSTI2023

Discrete element modeling of granular hopper flow of irregular-shaped deformable particles

Many natural and engineered granular materials have relatively deformable particles. Besides particle size and shape, particle deformability is another salient factor that significantly impacts the material’s flow behavior. Here, in this work, the flow of irregular-shaped deformable particles in a wedge-shaped hopper is investigated using discrete element simulations. A bonded-sphere model is developed to simultaneously capture irregular particle shapes and particle-wise deformations (e.g., compression, deflection, and distortion). Quantitative analysis of the effects of irregular shapes and particle deformations shows that the increase in particle stiffness tends to increase initial packing porosity and decrease the flow rate in the hopper. Rigid particles tend to have clogging issues, whereas deformable particles have less chance to, indicating particle deformation reduces the critical bridging width in the hopper flow. Detailed analysis of stress fields is also conducted to provide insights into the mechanism of particle flow and clogging. Stresses and discharge rates calculated from numerical simulations are compared and show good agreement with Walker’s theory and the extended Beverloo formula. Simulations with various particle shape combinations are also performed and show that the initial packing porosity decreases with an increasing percentage of fibers while the discharge rate has a complex dependency on particle shapes.

09 BIOMASS FUELS↗
DOE OSTI2024

Scale-Up Studies for the Dehydration of C 4+ Alcohols into Drop-In Diesel Fuel

Herein, we demonstrate the production of liter quantities of drop-in diesel-range ethers from biomass-derived alcohols. We report scale-up resultsfor the dehydration of a mixture of C 4+ alcohols using powder and pellet zeolite Ycatalyst in continuous flow and batch reactors. The activity of zeolite Y decreaseswith the introduction of an alumina binder. Large alcohols, as well as branchedand secondary alcohols, increase the coke content over the pellet Y catalyst. Thepellet formulation had lower carbon balances and selectivity to C 10+ ethers,suggesting that the pellet formulation increases alcohol absorption and cokeproduction. Crushing the pellet Y catalyst to smaller particle sizes does notrecover the activity of zeolite Y in its powder form. Cold flow experiments showthat particle agglomeration contributes to pressure buildup in the continuous flowreactor. C 10+ ether blends can be produced in batch reactors at high alcohol conversion regimes. One liter of a diesel #2 blend wasproduced by scaling up this reaction. The final blend consists of a substantial portion of C 10+ ethers (63.7 wt %), followed by heavyunknown products (27.4 wt %). Furthermore, the final alcohol and butyl ether concentration values were 7.3 and 1.5 wt %, respectively. Theblendstock reported in this paper can satisfy diesel #2 ASTM standards for density, cloud point, flashpoint, and cetane number.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗