Search NASA⌕ Search

SEARCH · Search NASA

Results for “high energy density plasmas”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Mechanisms for Pole Piece Erosion in a 6-kW Magnetically-Shielded Hall Thruster

The mechanisms contributing to the erosion of the inner magnetic pole of a 6-kW magnetically shielded Hall thruster are experimentally and numerically investigated. Sputtering from ion bombardment is believed to be the cause of this wear, but the nature and source of the responsible ions remains unknown. Laser induced fluorescence and translating and surface-mounted probes are employed to characterize the flux and energy distribution of ions incident at the inner pole. It is found that the bulk population is comprised of ions originating from the cathode plume and the near field immediately adjacent to the inner pole. These ions have a low average kinetic energy, < 5 eV kinetic, but a high thermal spread in velocity, Ti = 10 eV. Calculations for the erosion at the pole from experimental measurements indicate that the bulk population only accounts for 10-25% of the observed erosion. It is postulated that the remainder of the erosion results from a separate population of ions with sufficiently high energy (> 150 V) to cause high sputtering but too low density to be detected experimentally by the plasma diagnostics in this region. The existence for this high energy population is shown to be a consequence of the high plasma potentials downstream of the thruster exit plane that are characteristic of a magnetically-shielded topography. A simulation validated by experimental measurements of the thruster provides further evidence that a high energy ion populations exists with sufficient density to explain the observed erosion.

Jorns, Benjamin A.↗
NASA NTRS1992

Aerosol-induced laser breakdown thresholds - Effect of resonant particles

Laser intensity thresholds for the onset of stimulated Raman scattering and the breakdown in resonant micron-sized droplets are reduced to below those for nonresonant droplets by a factor of about 3. This reduction is most likely caused by the enhancement of electromagnetic energy (photon) densities within the droplets over and above that in nonresonant droplets. The magnitude of the threshold reduction for breakdown is consistent with the assertion that: (1) input (pump) wavelength resonances that initiate plasma have cavity Qs of about 10 exp 4; and (2) finite regions of high-electromagnetic-energy density within the droplet, with dimensions of the order of the Debye length, are required to initiate plasma.

Pinnick, R. G.↗
NASA NTRS1975

Collisionless shock waves in space - A very high beta structure

Measurements from six OGO-5 particle and field experiments are used to examine the structure of the earth's bow shock during a period of extremely high beta (the ratio of plasma thermal to magnetic energy density), as determined from simultaneous measurements of the upstream plasma on board the HEOS satellite. Even though the interplanetary field is nearly perpendicular to the shock normal, the shock is extremely turbulent. Large field increases are observed up to a factor of 20 above the upstream values. Ahead of these large enhancements, smaller magnetic effects accompanied by electrostatic noise, electron heating, and ion deflection are observed for several minutes. These observations suggest that a steady-state shock may not be able to form at very high beta. Further, they show that while the magnetic energy density may be relatively unimportant in the upstream flow, it can become very significant within the shock structure, and hence the magnetic field should not be ignored in theoretical treatments of very high beta shocks.

Formisano, V.↗
NASA NTRS1986

Near-conjugate observations of polar cusp electron precipitation using DE 1 and DE 2

The DE 1/2 plasma measurements of the dayside polar cusp at high and low altitudes have been examined for six near-conjugate passes. The plasma moments of downward electrons are computed, including energy flux, near flux, number density, and average energy from plasma data from both the high-altitude plasma instrument and the low-altitude plasma instrument. The DE 1/2 plasma measurements at the peaks of energy flux are compared, and the downward energy flux expected at the DE 2 altitude is modelled according to the convergence of magnetic flux tubes and using the DE 1 plasma data.

Lin, C. S.↗
NASA NTRS1979

Pitch-angle diffusion by whistler mode waves near the Io plasma torus

As Voyager 1 traversed the inner radiation belt of Jupiter, wave-particle interactions involving energetic electrons and whistler mode turbulence were strongly affected by the presence of the Io plasma torus. Within the high density torus the resonant electron energy was low and the associated high index of refraction yielded high B-to-E ratios for the wave fields, leading to very strong pitch-angle scattering. It is shown that significant spatial and temporal variations in plasma conditions produced large fluctuations in local scattering times, and the problems associated with the evaluation of precipitation lifetime are discussed.

Scarf, F. L.↗
NASA NTRS1997

Predictive Modeling in Plasma Reactor and Process Design

Research continues toward the improvement and increased understanding of high-density plasma tools. Such reactor systems are lauded for their independent control of ion flux and energy enabling high etch rates with low ion damage and for their improved ion velocity anisotropy resulting from thin collisionless sheaths and low neutral pressures. Still, with the transition to 300 mm processing, achieving etch uniformity and high etch rates concurrently may be a formidable task for such large diameter wafers for which computational modeling can play an important role in successful reactor and process design. The inductively coupled plasma (ICP) reactor is the focus of the present investigation. The present work attempts to understand the fundamental physical phenomena of such systems through computational modeling. Simulations will be presented using both computational fluid dynamics (CFD) techniques and the direct simulation Monte Carlo (DSMC) method for argon and chlorine discharges. ICP reactors generally operate at pressures on the order of 1 to 10 mTorr. At such low pressures, rarefaction can be significant to the degree that the constitutive relations used in typical CFD techniques become invalid and a particle simulation must be employed. This work will assess the extent to which CFD can be applied and evaluate the degree to which accuracy is lost in prediction of the phenomenon of interest; i.e., etch rate. If the CFD approach is found reasonably accurate and bench-marked with DSMC and experimental results, it has the potential to serve as a design tool due to the rapid time relative to DSMC. The continuum CFD simulation solves the governing equations for plasma flow using a finite difference technique with an implicit Gauss-Seidel Line Relaxation method for time marching toward a converged solution. The equation set consists of mass conservation for each species, separate energy equations for the electrons and heavy species, and momentum equations for the gas. The sheath is modeled by imposing the Bohm velocity to the ions near the walls. The DSMC method simulates each constituent of the gas as a separate species which would be analogous in CFD to employing separate species mass, momentum, and energy equations. All particles including electrons are moved and allowed to collide with one another with the stipulation that the electrons remain tied to the ions consistent with the concept of ambipolar diffusion. The velocities of the electrons are allowed to be modified during collisions and are not confined to a Maxwellian distribution. These benefits come at a price in terms of computational time and memory. The DSMC and CFD are made as consistent as possible by using similar chemistry and power deposition models. Although the comparison of CFD and DSMC is interesting, the main goal of this work is the increased understanding of high-density plasma flowfields that can then direct improvements in both techniques. This work is unique in the level of the physical models employed in both the DSMC and CFD for high-density plasma reactor applications. For example, the electrons are simulated in the present DSMC work which has not been done before for low temperature plasma processing problems. In the CFD approach, for the first time, the charged particle transport (discharge physics) has been self-consistently coupled to the gas flow and heat transfer.

Hash, D. B.↗
NASA NTRS1981

High-latitude ionospheric model - First step towards a predictive capability

In order to study the plasma density features associated with both weak and strong convection in the winter high-latitude F-region, a simple plasma convection model was combined with an ionospheric-atmospheric composition model. In a model calculation, a field tube of plasma is followed as it moves along a convection trajectory through a moving, neutral atmosphere. The altitude profiles of the ion densities are obtained by solving the appropriate continuity, momentum and energy equations, including many high-latitude processes. The result of following many such plasma field tubes is a time-dependent, three-dimensional ion density distribution for the ions NO(+), O2(+), O(+), N(+), and He(+). The high-latitude ionosphere is covered over one complete day above 42 deg N magnetic latitude, at altitudes of 160-800 km.

Schunk, R. W.↗
NASA NTRS1979

A cesium TELEC experiment at Lewis Research Center

The thermoelectronic laser energy converter (TELEC), was studied as a method of converting a 10.6 mm CO2 laser beam into electric power. The calculated characteristics of a TELEC seem to be well matched to the requirements of a spacecraft laser energy conversion system. The TELEC is a high power density plasma device which absorbs an intense laser beam by inverse bremsstrahlung with the plasma electrons. In the TELEC process, electromagnetic radiation is absorbed directly in the plasma electrons producing a high electron temperature. The energetic electrons diffuse out of the plasma striking two electrodes which are in contact with the plasma at the boundaries. These two electrodes have different areas: the larger one is designated as the collector, the smaller one is designated as the emitter. The smaller electrode functions as an electron emitter to provide continuity of the current. Waste heat is rejected from the collector electrode. An experiment was carried out with a high power laser using a cesium vapor TELEC cell with 30 cm active length. Laser supported plasma was produced in the TELEC device during a number of laser runs over a period of several days. Electric power from the TELEC was observed with currents in the range of several amperes and output potentials of less than 1 volt. The magnitudes of these electric outputs were smaller than anticipated but consistent with the power levels of the laser during this experiment.

Britt, E. J.↗
NASA NTRS1982

Status of thermoelectronic laser energy conversion, TELEC

A concept known as a thermo-electronic laser energy converter (TELEC), was studied as a method of converting a 10.6 micron CO2 laser beam into electric power. The calculated characteristics of a TELEC seem to be well matched to the requirements of a spacecraft laser energy conversion system. The TELEC is a high power density plasma device which absorbs an intense laser beam by inverse bremsstrahlung with the plasma electrons. In the TELEC process, electromagnetic radiation is absorbed directly in the plasma electrons producing a high electron temperature. The energetic electrons diffuse out of the plasma striking two electrodes which are in contact with the plasma at the boundaries. These two electrodes have different areas: the larger one is designated as the collector, the smaller one is designated as the emitter. The smaller electrode functions as an electron emitter provide continuity of the current. Waste heat is rejected from the collector electrode. An experiment was carried out with a high power laser using a cesium vapor TELEC cell with 30 cm active length. Laser supported plasma were produced in the TELEC device during a number of laser runs over a period of several days. Electric power from the TELEC was observed with currents in the range of several amperes and output potentials of less than 1 volt.

Britt, E. J.↗
NASA NTRS1985

Coupled low-energy - ring current plasma diffusion in the Jovian magnetosphere

The outwardly diffusing Iogenic plasma and the simultaneously inwardly diffusing ring current plasma in the Jovian magnetosphere are described using a coupled diffusion model which incorporates the effects of the pressure gradient of the ring current into the cross-L diffusion coefficient. The coupled diffusion coefficient is derived by calculating the total energy available to drive the diffusion process. The condition is imposed that the diffusion coefficient takes on a local minimum value at some point in the region L = 7-8, at which point the gradient of the Io plasma density is specified as ramp value given by Siscoe et al. (1981). The hypothesis that the pressure gradient of the ring current causes the diminution of radial plasma transport is tested, and solution profiles for the Iogenic and ring current plasma densities are obtained which imply that the Io plasma ramp is caused by a high-density, low-energy component of the ring current hitherto unobserved directly.

Summers, D.↗
NASA NTRS1998

Ion Energy Distributions and their Relative Abundance in Inductively Coupled Plasmas

Study of kinetics of ions and neutrals produced in high density inductively coupled plasma (ICP) discharges is of great importance for achieving a high degree of plasma assisted deposition and etching. In this paper, we present the ion energy distributions (IEDs) of various ions arriving at the grounded lower electrode. The ions were energy as well as mass analyzed by a combination of electrostatic analyzer-quadrupole mass spectrometer for pure Ar and CF4/Ar mixtures. The measurements have been made at gas pressures ranging from 30 to 100 mTorr. In addition, the IEDs were measured when the wafer-supporting electrode was also rf-powered and the effect of the self-bias was observed in the energy distributions of ions. The shapes of the IEDs are discussed an related to the sheath properties and measured electrical waveforms, as a function of pressure and applied power. Relative ion intensities were obtained by integration of each ion kinetic energy distribution function over its energy range.

Kim, J. S.↗
NASA NTRS2022

Stormtime Ring Current Heating of the Ionosphere and Plasmasphere

The energy deposition from ring current ions into the high density “cold” plasma of the ionosphere and plasmasphere is analyzed, based on a Comprehensive Inner Magnetosphere-Ionosphere simulation of the 2015 October 7 storm. In addition, the Naval Research Laboratory Sami3 is Also a Model of the Ionosphere ionosphere/plasmasphere code is used to simulate the effect of Coulomb-collision heating of plasmasphere and ionosphere electrons by ring current ions. We find that, during stormtime peaks in the Dst index, energy is deposited at altitudes as low as 100 km. Heating along the entirety of any given field line, both in the ionosphere and plasmasphere, contributes to increased temperatures in the ionosphere F layer and inner magnetosphere and to subsequent cold O + outflows. However, relative to the heating of the plasmasphere, the direct heating of the ionosphere by ring current ions produces only small effects. Qualitative model-data agreement on the N + /O + density ratio is consistent with the hypothesis that these outflows are driven by thermal forcing.

J. Krall↗
NASA NTRS1978

Low-energy plasma observations at synchronous orbit

The University of California at San Diego Auroral Particles Experiment on the ATS 6 satellite in synchronous orbit has detected a low-energy plasma population which is separate and distinct from both the ring current and the plasma sheet populations. The density and temperature of this low-energy population are highly variable, with temperatures in the range kT = 1-30 eV and densities ranging from less than 1 per cu cm to more than 10 per cu cm. The occurrence of a dense low-energy plasma is most likely in the afternoon and dusk local time sectors, whereas n greater than 1 per cu cm is seen in the local night sector only during magnetically quiet periods. These observations suggest that this plasma is the outer zone of the plasmasphere. During magnetically active periods this low-energy plasma is often observed flowing sunward. In the dusk sector, strong sunward plasma flow is often observed for 1-2 hours prior to the onset of a substorm-associated particle injection.

Lennartsson, W.↗
NASA NTRS1979

Development of tunable high pressure CO2 laser for lidar measurements of pollutants and wind velocities, January 1976 to December 1977

A tunable multiatmospheric pulsed CO2 laser with emphasis on experimental features and supporting theoretical analyses important to differential absorption lidar and Doppler lidar measurement of pollutants and wind velocities is reported. The energy deposition and the means to produce the uniform high density plasma in the multiatmospheric medium, through UV preionization of an organic seed gas is discussed. Design features of the pulsed CO2 laser are presented. The radiative processes which are operative and prevent the laser from breaking into oscillations in a large number of modes over its broad amplification bandwidth are described. The mode competition for the transient pulsed laser oscillation in a standing wave and traveling wave ring laser configuration is discussed and contrasted with the approach to steady state oscillations. The latter findings are important to transient injection locking for production of a highly stable pulsed CO2 laser output.

Javan, A.↗
NASA NTRS2003

Magnetohydrodynamic Augmented Propulsion Experiment: I. Performance Analysis and Design

The performance of conventional thermal propulsion systems is fundamentally constrained by the specific energy limitations associated with chemical fuels and the thermal limits of available materials. Electromagnetic thrust augmentation represents one intriguing possibility for improving the fuel composition of thermal propulsion systems, thereby increasing overall specific energy characteristics; however, realization of such a system requires an extremely high-energy-density electrical power source as well as an efficient plasma acceleration device. This Technical Publication describes the development of an experimental research facility for investigating the use of cross-field magnetohydrodynamic (MHD) accelerators as a possible thrust augmentation device for thermal propulsion systems. In this experiment,a 1.5-MW(sub e) Aerotherm arc heater is used to drive a 2-MW(sub e) MHD accelerator. The heatsink MHD accelerator is configured as an externally diagonalized, segmented channel, which is inserted into a large-bore, 2-T electromagnet. The performance analysis and engineering design of the flow path are described as well as the parameter measurements and flow diagnostics planned for the initial series of test runs.

Litchford, R. J.↗
NASA NTRS2010

Microwave Plasma Hydrogen Recovery System

A microwave plasma reactor was developed for the recovery of hydrogen contained within waste methane produced by Carbon Dioxide Reduction Assembly (CRA), which reclaims oxygen from CO2. Since half of the H2 reductant used by the CRA is lost as CH4, the ability to reclaim this valuable resource will simplify supply logistics for longterm manned missions. Microwave plasmas provide an extreme thermal environment within a very small and precisely controlled region of space, resulting in very high energy densities at low overall power, and thus can drive high-temperature reactions using equipment that is smaller, lighter, and less power-consuming than traditional fixed-bed and fluidized-bed catalytic reactors. The high energy density provides an economical means to conduct endothermic reactions that become thermodynamically favorable only at very high temperatures. Microwave plasma methods were developed for the effective recovery of H2 using two primary reaction schemes: (1) methane pyrolysis to H2 and solid-phase carbon, and (2) methane oligomerization to H2 and acetylene. While the carbon problem is substantially reduced using plasma methods, it is not completely eliminated. For this reason, advanced methods were developed to promote CH4 oligomerization, which recovers a maximum of 75 percent of the H2 content of methane in a single reactor pass, and virtually eliminates the carbon problem. These methods were embodied in a prototype H2 recovery system capable of sustained high-efficiency operation. NASA can incorporate the innovation into flight hardware systems for deployment in support of future long-duration exploration objectives such as a Space Station retrofit, Lunar outpost, Mars transit, or Mars base. The primary application will be for the recovery of hydrogen lost in the Sabatier process for CO2 reduction to produce water in Exploration Life Support systems. Secondarily, this process may also be used in conjunction with a Sabatier reactor employed to stockpile life-support oxygen as well as propellant and fuel production from Martian atmospheric CO2

Atwater, James↗
NASA NTRS2004

Experimentally Determined Plasma Parameters in a 30 cm Ion Engine

Single planar Langmuir probes and fiber optic probes are used to concurrently measure the plasma properties and neutral density variation in a 30cm diameter ion engine discharge chamber, from the immediate vicinity of the keeper to the near grid plasma region. The fiber optic probe consists of a collimated optical fiber recessed into a double bore ceramic tube fitted with a stainless steel light-limiting window. The optical fiber probe is used to measure the emission intensity of excited neutral xenon for a small volume of plasma, at various radial and axial locations. The single Langmuir probes, are used to generate current-voltage characteristics at a total of 140 spatial locations inside the discharge chamber. Assuming a maxwellian distribution for the electron population, the Langmuir probe traces provide spatially resolved measurements of plasma potential, electron temperature, and plasma density. Data reduction for the NSTAR TH8 and TH15 throttle points indicates an electron temperature range of 1 to 7.9 eV and an electron density range of 4e10 to le13 cm(sup -3), throughout the discharge chamber, consistent with the results in the literature. Plasma potential estimates, computed from the first derivative of the probe characteristic, indicate potential from 0.5V to 11V above the discharge voltage along the thruster centerline. These values are believed to be excessively high due to the sampling of the primary electron population along the thruster centerline. Relative neutral density profiles are also obtained with a fiber optic probe sampling photon flux from the 823.1 nm excited to ground state transition. Plasma parameter measurements and neutral density profiles will be presented as a function of probe location and engine discharge conditions. A discussion of the measured electron energy distribution function will also be presented, with regards to variation from pure maxwellian. It has been found that there is a distinct primary population found along the thruster centerline, which causes estimates of electron temperature, electron density, and plasma potential, to err on the high side, due this energetic population. Computation of the energy distribution fimction of the plasma clearly indicates the presence of primaries, whose presence become less obvious with radial distance from the main discharge plume.

near grid plasma↗
NASA NTRS1983

Long-lived particulate or gaseous structure in Saturn's outer magnetosphere

Voyager 1 and 2 and Pioneer 11 data on the variations in the number density of low-energy plasma ions in the outer Saturn magnetosphere are discussed. Low and high latitude observations are compared in reference to the position of the spacecraft crossing of the field line. Abrupt decreases in the number density interrupted the tendancy for the number density to increase with spacecraft approach to Saturn. All three spacecraft are concluded to have encountered the same magnetospheric structure in the field line, with absorbers being present in the equatorial plane. The absorbers are suggested to be either gas or debris, which may be detectable visibly or with occultation techniques.

Lazarus, A. J.↗