Search NASA⌕ Search

SEARCH · Search NASA

Results for “hopper design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

30 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

A deep insight on the coal ash-to-slag transformation behavior during the entrained flow gasification process

Recent research provided deep insight on the coal ash-to-slag transformation characterization during the entrained flow gasification process, with experimentation on a 40 kg/hr (dry basis) coal-fed opposed multi-burner (OMB) entrained flow gasifier and simulation via FactSage™ software. A general mechanism is presented to relate the gasifier design temperature, ash fluid temperature, and operating temperature with the degree of the slag polymerization. The change of the high temperature zone, the corresponding particle residence time in the high temperature zone, and syngas composition have obvious effects on the slag mineral transformation behavior. Mineral types formed on the wall of the gasifier chamber were mainly anorthite (CaAl 2 Si 2 O 8 ), aluminum oxide (Al 2 O 3 ), and calcium sulfide (CaS). These minerals transformed to anorthite and diopside (CaMgSi 2 O 6 ) at the slag hole zone, while the minerals at the lock hopper were anorthite, orthoclase (KAlSi 3 O 8 ), quartz (SiO 2 ), gypsum (CaSO 4 ), calcite (CaCO 3 ), and halite (NaCl). FactSage™ predicted minerals as anorthite, diopside, orthoclase, and albite (NaAlSi 3 O 8 ), etc., where the slag temperature was below the ash fluid temperature and when the ratios of CO/CO 2 and (CO + H 2 )/CO 2 were lower than 1.0 and 2.0, respectively. By simulation, residual carbon was found to be the dominant factor over syngas composition to cause mineral transformation, and this was verified experimentally. The Ca-based crystals, typically anorthite, was shifted to diopside, near the slag hole zone, and a linear relationship was found between the content ratios of diopside/(anorthite + diopside), CaO/SiO 2 , and (CaO + MgO)/SiO 2 . A dimensionless number, θ, was defined to characterize the changing chemical composition and the degree of slag polymerization, with temperature deviation from the design condition. Three zones of θ were identified and related to the deviation between the actual gasification condition from the design condition. Finally, a low slag polymerization degree corresponded with a higher temperature deviation between the actual condition and design condition, and this proved that increased residual carbon content and changing iron valence state increased the mineral types when the slag temperature was below the ash fluid temperature.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2024

SPH Modeling of Biomass Granular Flow: Engineering Application in Hoppers and Augers

Numerical modeling of granular biomass material flow in handling operations is indispensable to decipher flow upsets, commonly manifested as clogging and jamming in hoppers and augers. With a computational tool developed based on smoothed particle hydrodynamics (SPH), we simulated the hopper flow and auger feeding of six granular biomass materials. The good agreement between the experimental and numerical flow rates demonstrated the capability of the developed SPH solver in modeling the complicated flow of granular biomass materials. Further, the impact of physical and numerical parameters is investigated, and the major results show that the hopper flow pattern is controlled by shear band evolution; hopper clogging is collectively influenced by the opening size, wall friction, and material packing, and the impact of material compressibility on the auger feed rate is minimal. These parametric studies validate the solver’s robustness in simulating biomass flow in handling equipment and demonstrate that the SPH computational tool can provide insights about granular flow mechanics to facilitate handling equipment design and optimize handling operations.

09 BIOMASS FUELS↗
DOE OSTI2020

Characterizing material transitions in large-scale Additive Manufacturing

Integrating Multiple Materials (MM) into large-scale Additive Manufacturing (AM) is a key for various industrial applications wishing to incorporate site-specific properties into geometrically complex designs that are difficult to manufacture with traditional techniques. Printing with multiple materials is typically accomplished by using layers as natural material boundaries, but having the capability to switch between materials within a single layer without pausing would further expand MM possibilities. This study used Cincinnati Incorporated’s Big Area Additive Manufacturing (BAAM) system to explore material transitions with a novel dual-hopper that enables in-situ material blending of a pelletized feedstock. Constructing MM and functionally graded material (FGM) structures requires depositing a specific material composition at a specific geometric location to achieve a desired performance. Furthermore, accurately implementing this with the BAAM’s blended extrusion system requires a thorough understanding of the transition between distinct material compositions. This study characterizes a step-change transition between neat acrylonitrile butadiene styrene (ABS) and carbon fiber-reinforced ABS. Three distinct techniques were compared for analyzing the fiber content, and the transition zone between materials was characterized as a function of transition direction. The transition process was consistent to within 0.7 wt% carbon fiber variation between different layers and prints. The transition between materials was found to be directionally dependent, with ABS to CF/ABS having a transition length of 3.5 m compared to 3.2 m for CF/ABS to ABS. Furthermore, the transition from Material A to Material B was found to be repeatable with a possible variance in transition length of 0.3 m.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Physical Properties of Moist, Fermented Corn Kernels

A novel approach to producing corn stover biomass feedstock has been investigated. In this approach, corn grain and stover are co-harvested at moisture contents much less than typical corn silage. The grain and stover are conserved together by anaerobic storage and fermentation and then separated before end use. When separated from the stover, the moist, fermented grain had physical characteristics that differ from typical low-moisture, unfermented grain. A comprehensive study was conducted to quantify the physical properties of this moist, fermented grain. Six corn kernel treatments, either fermented or unfermented, having different moisture contents, were used. Moist, fermented kernels (26 and 36% w.b. moisture content) increased in size during storage. The fermented kernels’ widths and thicknesses were 10% and 15% greater, respectively, and their volume was 28% greater than the dry kernels (15% w.b.). Dry basis particle density was 9% less for moist, fermented kernels. Additionally, the dry basis bulk density was 29% less, and the dry basis hopper-discharged mass flow rate was 36% less. Moist, fermented grain had significantly greater kernel-to-kernel coefficients of friction and angles of repose compared to relatively dry grain. The friction coefficient on four different surfaces was also significantly greater for fermented kernels. Fermented corn kernels had lower individual kernel rupture strengths than unfermented kernels. These physical differences must be considered when designing material handling and processing systems for moist, fermented corn grain.

09 BIOMASS FUELS↗
DOE OSTI2021

Abrasion wear at high temperature in particle receiver type Concentrating Solar Power Systems

The use of solid particles as a heat transfer fluid in receivers for concentrating solar powerplants has garnered much attention in the past decade. Particles are not only stable at temperatures above 700 °C but are also able to absorb solar energy directly, which gives them a distinct advantage over conventional molten salts. The use of particles can, however, cause material degradation from the flow of hot or cold particles through discharge hoppers or along the inner receiver surfaces and other system components (e.g. tubes, valves etc.), depending on operating mode of the receiver. Stainless steel alloy 316, nickel-based alloy Inconel® 740H®, Haynes 230, and a 60% alumina, low-cement refractory castable from Allied Mineral Products were tested for wear from first-of-a-kind high-temperature low-velocity abrasion-erosion experiments. The tests are designed to simulate potential conditions in Generation 3 falling particle Concentrating Solar Power (CSP) systems. Simultaneous experiments were conducted at room temperature as well to draw comparison on the role of temperature on abrasion wear rates. It was noted that the abrasion wear rate in candidate materials was driven by the oxidation resistance of the material. The findings from these experiments will be used to determine life-time of critical components in particle receiver concentrated solar powerplants.

14 SOLAR ENERGY↗
DOE OSTI2021

Computational Fluid Dynamics Simulation of Compressible Non-Newtonian Biomass in a Compression-Screw Feeder

Compression-screw feeders play a critical role in biorefineries to transport lignocellulosic biomass feedstocks from the feeding hoppers to biomass-conversion reactors in order to pretreat and convert biomass to hydrocarbon liquid biofuels and other power and energy resources. One of the main challenges in the operation of screw feeder is plugging and jamming of compressed biomass with high concentration of insoluble solids. The focus of this paper is to numerically investigate the screw feeder at these challenging operating conditions and help with the optimization of the screw feeder design to avoid operation failure. In this work a customized CFD model based on open-source OpenFOAM package [1] was developed to simulate the concentrated biomass as a highly viscous non-Newtonian fluid in the screw feeder. The biomass is modeled as a single-phase compressible Bingham fluid with a plastic viscosity as well as a density-dependent yield stress. The compressibility formulation (pressure-dependent density) and the density-dependent yield stress formulation in the governing equations follow the suggestions from a recent study by Duncan et al. [2]. A pilot-scale hopper/screw feeding system at NREL [3] is used to compare the experimental observations with our simulation results. The auger is 280 mm long and tapered with outer diameter changing from 80 mm to 35 mm. The auger rotates from 10 to 60 rpm in a conical throat which contains anti-rotational bars. The simulations predicted the required torque for the screw feeder and the pressure increase at the exit for biomass feedstocks with various fluid viscosity properties and auger rotating speeds. The analysis of the stress forces helped to identify the critical conditions were the screw feeder excessive wear or jamming could occur.

biofuels↗
DOE OSTI2022

On the Fidelity of Computational Models for the Flow of Milled Loblolly Pine: A Benchmark Study on Continuum-Mechanics Models and Discrete-Particle Models

The upstream of bioenergy industry has suffered from unreliable operations of granular biomass feedstocks in handling equipment. Computational modeling, including continuum-mechanics models and discrete-particle models, offers insightful understandings and predictive capabilities on the flow of milled biomass and can assist equipment design and optimization. This paper presents a benchmark study on the fidelity of the continuum and discrete modeling approaches for predicting granular biomass flow. We first introduce the constitutive law of the continuum-mechanics model and the contact law of the coarse-grained discrete-particle model, with model parameters calibrated against laboratory characterization tests of the milled loblolly pine. Three classical granular material flow systems (i.e., a lab-scale rotating drum, a pilot-scale hopper, and a full-scale inclined plane) are then simulated using the two models with the same initial and boundary conditions as the physical experiments. The close agreement of the numerical predictions with the experimental measurements on the hopper mass flow rate, the hopper critical outlet width, the material stopping thickness on the inclined plane, and the dynamic angle of repose, clearly indicates that the two methods can capture the critical flow behavior of granular biomass. The qualitative comparison shows that the continuum-mechanics model outperforms in parameterization of materials and wall friction, and large-scale systems, while the discrete-particle model is more preferred for discontinuous flow systems at smaller scales. Industry stakeholders can use these findings as guidance for choosing appropriate numerical tools to model biomass material flow in part of the optimization of material handling equipment in biorefineries.

Jin, Wencheng↗
DOE OSTI2020

Radioactive Cleaning Robot

Here at Fermi National Accelerator Laboratory, particle accelerators are constantly running, giving off excess radioactive dust. This dust can be extremely harmful to people and the environment, posing numerous issues. The goal of this project is to conceptualize an automated cleaning solution. With this main goal in mind, the project started with a brainstorming session. The main concept relied on the use of a powder distributing system paired with a vacuum to easily attract and trap the dust. From this main concept, multiple sketches were produced, showing a robot with pieced-together systems. With the initial idea down, each subsystem could be brought further with the inner workings being sketched out. After sketches and proof of concept were polished, the next step was to begin 3D modeling, using NX, to bring life into the sketches. With every day came new ideas, modifying the previous sketches and models as necessary. Soon after the bigger structures were fleshed out, the focus could be shifted onto the less pressing subsystems. Adding a conveyor belt and spinning brush attachment to the powder hopper allowed for more even powder distribution. Along with that, the addition of spring-loaded brushes on the vacuum nozzle ensures constant dust agitation, improving overall functionality. A few other quality of life improvements, such as a removable dust reservoir with a ramp gave a push towards real life functionality. After considering the logistics of this robot functioning in real-life, pressure plates were provided to stop the robot from crashing into its surroundings. Having all of the individual models lead to an overall assembly. Making this robot programmable allowed for this project to meet the design requirements, providing a solution to the previous dilemma.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Synthesis of nanograined zirconium diboride microsphere powder feedstock via emulsification of suspensions

Ceramic nanograined materials have desirable characteristics compared to their macroparticle counterparts but are rarely used in industrial applications due to issues with poor handleability and health hazards. Due to interparticle forces that become more dominant as the particle size decreases, it is difficult to use nanomaterials to fill dies, spread on surfaces, or flow through hoppers found in various manufacturing processes. In this work, we report a scalable gelcasting solution and unique emulsification process to create microspheres composed of nanoscale powders to enhance the flowability and handleability of nanomaterials. The gelcasting solution and emulsification process can be used with any nanoparticle composition that can be suspended in a liquid phase. This paper reports the effects of various parameters on zirconium diboride microsphere formation, such as surfactant content and mixing conditions. The microspheres maintain the nano-scale characteristics of the powder but improve its flowability by using cross-linked polyvinyl alcohol to combine irregularly shaped zirconium diboride nanoparticles with a particle diameter of 60 nm into larger spherical particles with a d 50 ~25 μm. This hierarchical feedstock engineering design combine the positive characteristics of materials across both length scales and improve the flowability of the feedstock from a Hausner Ratio of 1.56 to 1.19. The materials produced using this technique can be used in thermal plasma spray, die filling for hot pressing or spark plasma sintering, and binder jet printing applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Multiscale Shear Properties and Flow Performance of Milled Woody Biomass

One dominant challenge facing the development of biorefineries is achieving consistent system throughput with highly variant biomass feedstock quality and handling performance. Current handling unit operations are adapted from other sectors (primarily agriculture), where some simplifying assumptions about granular mechanics and flow performance do not translate well to a highly compressible and anisotropic material with nonlinear time- and stress-dependent properties. This work explores the shear and frictional properties of loblolly pine at multiple experimental test apparatus and particle scales to elucidate a property window that defines the shear behavior over a range of material attributes (particle size, size distribution, moisture content, etc.). In general, it was observed that the bulk internal friction and apparent cohesion depend strongly on both the stress state of the sample in granular shear testers and the overall particle size and distribution span. For equipment designed to characterize the quasi-static shear stress failure of bulk materials ranging from 50 to 1,000 ml in test volume, similar test results were observed for finely milled particles (50% passing size of 1.4 mm) with a narrow size distribution (span between 10 and 90% passing size of 0.9 mm), while stress chaining and over-torque issues persisted for the bench-scale test apparatus for larger particle sizes or widely dispersed sample sizes. Measurement of the anisotropic particle–particle friction ranged from coefficients of approximately 0.20 to 0.45 and resulted in significantly higher and more variable friction measurements for larger particle sizes and in perpendicular alignment orientations. To supplement these laboratory-scale properties, this work explores the flow of loblolly pine and Douglas fir through a pilot-scale wedge-shaped hopper and a screw feeder. For the gravity-driven hopper flow, the critical arching distance and mass discharge rate ranged from approximately 10 to 30 mm and 2 to 16 tons/hour, respectively, for both materials, where the arching distance depends strongly on the overall particle size and depends less on the hopper inclination angle. Comparatively, the auger feeder was found to be much more impacted by the size of the particles, where smaller particles had a more consistent and stable flow while consuming less power.

09 BIOMASS FUELS↗
DOE OSTI2021

MFIX DEM Enhancement for Industry-Relevant Flows (Final Report)

The overall goal of this two-phase project is to implement performance improvements of the Multiphase Flow with Interphase Exchanges (MFIX) Discrete Element Model (DEM) code that enable a transformative shift for industrial use. Prior to this effort, the largest simulations performed using MFIX are O(10 7 ) particles. This falls short of the O(10 9 ) particle simulations that must be completed on a timescale of days or weeks (vs. months or years) to enable simulations with physically-relevant domain sizes to be incorporated into industrial design cycles within five years. This was accomplished by tailoring best-in-class practices to bear on the unique challenges posed by the MFIX-DEM algorithm and code base. Scientific simulations (e.g., in cosmology, turbulent combustion) routinely use massively parallel computing to update far more particles in short wall clock times. Results from Phase 1 (1.5 years in duration) indicated significant gains in speed were possible for a wide range of benchmark cases. Moreover, a survey sent to >35 companies indicates that the timing is ideal for such an enhanced tool, with >80% of the respondents indicating that DEM is already value-added or will be within the next 5 years, and >70% of the respondents indicating that improved speed is the top computational priority. In Phase 2 (3.5 years in duration), the two major barriers that hinder industry from effectively using multiphase Computational Fluid Dynamics (CFD) to cut costs and improve performance, namely computational overhead and confidence in predictions, continued to be addressed. Regarding the former, the results from Phase 1 to guide the effort, with enhancements focused on an improved time-stepping algorithm and particle sorting. Four target problems of 1 billion particles each and increasing complexity were identified: homogeneous cooling, tumbler with continuous particle size distribution, discharge from a rectangular hopper and a cylindrical riser. Each of these were successfully simulated for relevant time scales (on order of seconds) using less than 24 hours of wall clock time. These represent the first 1-billion particle DEM simulations performed with MFIX, namely using the MFIX-Exa code. This code is currently under development at NETL in collaboration with Lawrence Berkeley National Laboratory. Regarding the second barrier on predictive uncertainty, experiments from Phase 1 (interacting nozzles - hydrodynamics only) and Phase 2 (very small-scale segregation experiments) were used to demonstrate the ability of two simplified approaches to uncertainty quantification (UQ). By limiting the number of particles, UQ based on the simplified treatment was compared to standard UQ, which was shown to have much higher computational demands. Experiments were also performed on a pilot-scale stripper unit to provide validation data for future CFD-DEM simulations and UQ.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2024

Ultrafast Symmetry Control in Photoexcited Quantum Dots

Symmetry control is essential for realizing unconventional properties, such as ferroelectricity, nonlinear optical responses, and complex topological order, thus it holds promise for the design of emerging quantum and photonic systems. Nevertheless, fast and reversible control of symmetry in materials remains a challenge, especially for nanoscale systems. Here, reversible symmetry changes are unveiled in colloidal lead chalcogenide quantum dots on picosecond timescales. Using a combination of ultrafast electron diffraction and total X-ray scattering, in conjunction with atomic-scale structural modeling and first-principles calculations, it is revealed that symmetry-broken lead sulfide quantum dots restore to a centrosymmetric phase upon photoexcitation. The symmetry restoration is driven by photoexcited electronic carriers, which suppress lead off-centering for about 100 ps. Furthermore, the change in symmetry is closely correlated with the electronic properties, and the bandgap transiently red-shifts in the symmetry-restored quantum dots. Overall, this study elucidates reversible symmetry changes in colloidal quantum dots, and more broadly defines a new methodology to optically control symmetry in nanoscale systems on ultrafast timescales.

36 MATERIALS SCIENCE↗