Search NASA⌕ Search

SEARCH · Search NASA

Results for “improved microstructures and properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Friction stir processing: A thermomechanical processing tool for high pressure die cast Al-alloys for vehicle light-weighting

This study uses friction stir processing (FSP) for thermomechanical processing of high-pressure die-casting (HPDC) to modify microstructure and improve mechanical properties. FSP is carried out on two different HPDC aluminum alloys: (a) general-purpose, high-iron, HPDC A380 alloy and (b) premium quality, low-iron HPDC Aural-5 alloy in thin wall, flat plate geometry. Subsequent mechanical testing shows ~30 % and ~65 % enhancement in yield strength and tensile ductility. In addition, FSP leads to ~10 times improvement in fatigue life for A380 alloy and ~70 % improvement in fracture toughness for Aural-5 alloy. These findings emphasize the capability of FSP to modify the microstructure of HPDC Al-alloys-based structural components so that they can demonstrate a good combination of strength, ductility, fracture toughness, and high fatigue properties for long-term durability and reliability.

36 MATERIALS SCIENCE↗

Lattice-Boltzmann Simulations of Multiphase Flows in Gas-Diffusion-Layer (GDL) of a PEM Fuel Cell

Improved power density and freeze-thaw durability in automotive applications of Proton Exchange Membrane Fuel Cells (PEMFCs) requires effective water management at the membrane. This is controlled by a porous hydrophobic gas-diffusion-layer (GDL) inserted between the membrane catalyst layer and the gas reactant channels. The GDL distributes the incoming gaseous reactants on the catalyst surface and removes excess water by capillary action. There is, however, limited understanding of the multiphase, multi-component transport of liquid water, vapor and gaseous reactants within these porous materials. This is due primarily to the challenges of in-situ diagnostics for such thin (200 -“ 300 {microns}), optically opaque (graphite) materials. Transport is typically analyzed by fitting Darcy's Law type expressions for permeability, in conjunction with capillary pressure relations based on formulations derived for media such as soils. Therefore, there is significant interest in developing predictive models for transport in GDLs and related porous media. Such models could be applied to analyze and optimize systems based on the interactions between cell design, materials, and operating conditions, and could also be applied to evaluating material design concepts. Recently, the Lattice Boltzmann Method (LBM) has emerged as an effective tool in modeling multiphase flows in general, and flows through porous media in particular. This method is based on the solution of a discrete form of the well-known Boltzmann Transport Equation (BTE) for molecular distribution, tailored to recover the continuum Navier-Stokes flow. The kinetic theory basis of the method allows simple implementation of molecular forces responsible for liquid-gas phase separation and capillary effects. The solution advances by a streaming and collision type algorithm that makes it suitable to implement for domains with complex boundaries. We have developed both single and multiphase LB models and applied them to simulate flow through porous GDL materials. We will present an overview of the methods as implemented, verification studies for both microstructure reconstruction and transport simulations, and application to single- and two-phase transport in GDL structures. The applications studies are designed to both improve understanding of transport within a given structure, and to investigate possible routes for improving material properties through microstructure design.

30 DIRECT ENERGY CONVERSION↗

Microstructure-refinement–driven enhanced tensile properties of high-pressure die-cast A380 alloy through friction stir processing

This work employs friction stir processing (FSP), a well-known severe plastic deformation technique, to selectively modify the microstructure of thin-walled, high-pressure die-cast (HPDC) aluminum alloy A380, a major HPDC alloy fabricated in the die casting sector. FSP effectively breaks down Al dendrites and acicular Si particles, creating a homogenized distribution of equiaxed Si particles in the aluminum matrix. After FSP, the refined Si particles (~1.5 µm) are smaller than the eutectic Si particles (3–8 µm) in HPDC condition. In addition, interparticle distance has decreased almost 50% compared to dendritic arm spacing, and FSP has reduced the aspect ratio of Si particles to ~2. Furthermore, FSP eliminates porosity, and breaks down needle-like second-phase Fe-Mn and Cu-rich particles, yielding a refined, homogeneous distribution. The FSP-induced microstructural refinement and porosity reduction improve bulk yield strength and ductility by 23% and 66%. Tensile properties are enhanced beyond those of the die skin of the HPDC plate, and the alloy possesses lower defect density and a highly refined microstructure. This study establishes the viability of FSP as a tool for microstructure modification and mechanical property improvement for HPDC Al alloys for the light-weighting goal of the automotive industries.

36 MATERIALS SCIENCE↗

Effect of Tungsten Inert Gas Arc Remelting on Microstructure and Wear Properties of Plasma-Sprayed NiCr-Cr{sub 3}C{sub 2} Coating

In this work, a NiCr-Cr{sub 3}C{sub 2} coating was prepared on an AISI 1045 steel substrate by plasma spraying and then remelted with the tungsten inert gas (TIG) arc method. The purpose was to study the effects of TIG remelting treatment on the microstructure, mechanical properties and wear properties of a plasma-sprayed NiCr-Cr{sub 3}C{sub 2} coating. The results show that after TIG remelting, the density of the coating increased, the internal porosity decreased from 8.1 to 0.2%, and the number of cracks and inclusions greatly reduced. The hardness of the coating also became uniform and increased from 1007 to 1141 HV{sub 0.1}, with an obvious increase of 13.3%, and the fracture toughness increased by 321.3%. The wear volume after TIG remelting at room temperature was reduced by 59.5%, and the wear pattern changed from brittle fracture and abrasive wear to abrasive wear and adhesive wear. The wear loss at 700 °C was also reduced by 43.6%, and the wear pattern was transformed from brittle fracture and fatigue wear caused by oxidation to oxidative wear and adhesive wear. Therefore, TIG remelting treatment can effectively improve the microstructure, mechanical properties and wear resistance of a plasma-sprayed NiCr-Cr{sub 3}C{sub 2} coating.

36 MATERIALS SCIENCE↗

Wear resistance and microstructural properties of Ni–Al/h-BN/WC–Co coatings deposited using plasma spraying

Hexagonal boron nitride (h-BN) and tungsten carbide cobalt (WC–Co) were added to nickel aluminum alloy (Ni–Al) and deposited as plasma sprayed coatings to improve their tribological properties. The microstructure of the coatings was analyzed using a scanning electron microscope (SEM). Following wear test, the worn surface morphologies of the coatings were analyzed using a SEM to identify their fracture modes. The results of this study demonstrate that the addition of h-BN and WC–Co improved the properties of the coatings. Ni–Al/h-BN/WC–Co coatings with high hardness and favorable lubrication properties were deposited. - Highlights: • We mixed Ni–Al, h-BN and WC–Co powders and deposited them as composite coatings. • Adding WC–Co was found to increase the hardness and reduce the wear volume loss. • Adding h-BN was found to decrease the hardness and reduce the friction coefficient. • This composite coating was shown to have improved wear properties at 850 °C.

36 MATERIALS SCIENCE↗

Enhanced high-temperature tensile property by gradient twin structure of duplex high-Nb-containing TiAl alloy

A pre-deformation process was employed for a TiAl alloy via high-temperature torsion, in which the stability of the constituent phases was tailored, resulting in enhanced hardening capability and ductility via a gradient microstructure. A sample with a pre-torsion of 360° exhibited a yield strength of 475 MPa and an ultimate tensile strength of 592 MPa, with a tensile ductility of 47% at 850 °C. The tensile properties were significantly enhanced compared with the as-forged sample, which exhibited values of 395 MPa, 494 MPa, and 4.6%, respectively. The physical mechanisms for the significant enhancement of the mechanical property of the TiAl alloys were studied in-depth via of transmission electron microscopy, electron-backscattered diffraction, and high-energy X-ray diffraction techniques. The high strength is mainly attributed to the twin structure formed during torsion, while high fracture elongation correlates to the recrystallization of the γ phase at twin-twin sections and the load partitioning regulated by a hierarchical microstructure. When the tensile micro-strains along the loading direction and transverse direction in the γ phase of the pre-deformed TiAl alloy, a higher mechanical performance was obtained. Moreover, the fracture mode of the pre-torsional tensile sample is a combination of pores and cleavage facets which resulted from the microstructure after torsion. Finally, the gradient twin structure approach in this study provides a strategy for developing TiAl alloys with exceptionally high-temperature tensile property, and the results of the micromechanical behavior-microstructure-property relationship may improve the understanding of the plastic deformation of TiAl alloys.

36 MATERIALS SCIENCE↗

GaN nanowires with pentagon shape cross-section by ammonia-source molecular beam epitaxy

In this study, ammonia-based molecular beam epitaxy (NH 3 -MBE) was used to grow catalyst-assisted GaN nanowires on (11¯02) r-plane sapphire substrates. Dislocation free [112¯0] oriented nanowires are formed with pentagon shape cross-section, instead of the usual triangular shape facet configuration. Specifically, the cross-section is the result of the additional two nonpolar {101¯0} side facets, which appear due to a decrease in relative growth rate of the {101¯0} facets to the {101¯1} and {101¯1} facets under the growth regime in NH 3 -MBE. Compared to GaN nanowires grown by Ni-catalyzed metal–organic chemical vapor deposition, the NH 3 -MBE grown GaN nanowires show more than an order of magnitude increase in band-edge to yellow luminescence intensity ratio, as measured by cathodoluminescence, indicating improved microstructural and optical properties.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Process parameters and system responses in friction extrusion

We report friction extrusion is an emerging manufacturing process that imparts improved properties and unique microstructures to materials. In this study, the effects of die features (i.e., the absence or presence of die face scrolling) and process parameters (i.e., die rotational speeds and feed rates) on response variables (e.g., extrusion force, torque, power, and temperature) were investigated. During this work, wires with good integrity and similar geometries were extruded over a range of experimental trials with different rotational speeds and feed rates at a constant extrusion ratio. The extrusion force linearly varies with die advance per revolution, which is the ratio of feed rate and rotational speed. The extrusion energy per kilogram mass of extrudate varies non-linearly and asymptotically such that energy consumption is highest at the lowest feed rate and lowest at the highest feed rate. Additionally relationships among other variables (i.e., die advance per revolution, torque, power heat input, and temperature) also were evaluated to elucidate their interdependences.

42 ENGINEERING↗

Fabrication of thick multilayered steel structure using A516 Grade 70 by multipass friction stir welding

In the present work, a thick-sectioned multilayered steel structure was fabricated by multipass friction stir welding on A516 Grade 70 steel. Tensile strength of the multilayered samples was comparable to that of the base metal. Failure was located in the base metal when a defect-free sample was tested. Charpy impact toughness was higher in the stir zone and heat affected zone than in the base metal. Higher microhardness values were found in the stir zone and heat affected zone than the base metal due to grain refinement and modification of the microstructures. Consequently, improved mechanical properties compared to the base metal were found in the weld zones of friction stir welded A516 Grade 70 steel.

36 MATERIALS SCIENCE↗

Epoxy resin reinforced with carbonized chicken feathers: An innovative composite material with sustainable potentials

Here, this article explores a novel method for enhancing the mechanical properties of epoxy resin composites by incorporating carbonized chicken feathers as a filler material. The fabrication process involves carbonizing chicken feathers at 600°C and incorporating 5-10 wt% of the fillers into an epoxy matrix. The composites showed enhanced mechanical properties and samples containing 10 wt% filler exhibit the best properties. The performance corresponds to 49% increase in tensile strength, 16% rise in Young’s modulus, 40% improvement in flexural modulus, and 57% in flexural strength. X-ray diffraction and scanning electron microscopy with energy dispersive spectroscopy were employed to characterize the filler. This characterization provides valuable insights into the structure and chemical composition of the pulverized carbonized chicken feathers that contributed to the attained improvement in composites’ properties. Microstructural examination of the developed composite under scanning electron microscope also provides insights into matrix-filler interface and dispersion of the fillers within the composite matrix. The study not only highlights the unique combination of carbonized feathers’ inherent strength and compatibility with the epoxy matrix but also underscores the eco-friendly nature of utilizing agricultural waste. The findings suggest promising applications in industries demanding lightweight, high-strength materials, which can contribute to sustainable engineering solutions.

36 MATERIALS SCIENCE↗

Multi-Pass Hybrid Laser Arc Welding of Alloy 740H

The presentation reviews the progress made toward reducing the joining time of an advanced nickel-based alloy, Alloy 740H by a factor of two using a novel two step fusion welding approach. In the first step, a high powered laser is used to rapidly join thick weld groove lands (~10-12 mm thick) during a single pass. Hybrid laser arc welding (HLAW) is then used to fill the remaining weld groove and complete the joint. This sequential process also utilizes laser wobble in both steps to reduce welding defects and refine the weld microstructure to obtain improved properties compared to conventional gas tungsten or gas metal arc welds, GTAW and GMAW, respectively. The creep behavior of laser-only thick weld groove land welds and HLAW welds were found to be the same or slightly improved compared to conventional GMAW or GTAW welds in this alloy. Creep tests have been started to verify the long-term creep behavior (~10,000 hrs) of these welds. Modeling results on deep penetration laser welding are presented and the initial simulations of laser welding with laser wobble are shown. The next phase of the project will combine the two processes to make complete welds - deep penetration laser welds of thick weld groove lands followed by rapid filling of the remaining weld groove by HLAW - in thick plates (32 mm thick) Alloy 740H plate and entails development of narrow weld groove welding to further decrease the joining time of this alloy.

36 MATERIALS SCIENCE↗

Effect of Minor Er on the Microstructure and Properties of Al-6.0Mg-0.4Mn-0.1Cr-0.1Zr Alloys

As-cast Al-6.0Mg-0.4Mn-0.1Cr-0.1Zr alloys containing different additions of Er were prepared. Then, the specimens were carried out homogenization heat treatment, hot rolling, cold rolling, and annealing. The effects of minor Er on the microstructure and properties of Al-6.0Mg-0.4Mn-0.1Cr-0.1Zr alloy were investigated. Results show that addition of Er can refine the microstructure and improve the mechanical properties of the alloys. As for the annealed alloys, the addition of 0.33%Er can increase the tensile strength by 29 MPa. Strength increment is mainly attributed to refinement and the precipitation of Al{sub 3}Er and Al{sub 3}(Er, Zr). Additionally, the minor Er can improve the corrosion resistance of the alloys, which can be attributed to the compact composite oxide film of Er-O and Al-O, purification, and modification.

36 MATERIALS SCIENCE↗

Development of a Novel Magnesium Alloy for Thixomolding® of Automotive Components (Final Report)

Magnesium (Mg) alloy die-castings are increasingly used in the automobile industry to achieve cost effective mass reduction, especially in systems where multiple components can be integrated into a single thin wall die-casting. However, there are several component quality restrictions in thin-walled Mg die castings, including variability in dimensional accuracy, part-to-part variation in mechanical properties, and porosity in the final part, which has limited the continued growth of die-cast components in the automobile industry. An alternative to die-casting is the process of thixomolding®. While the die-casting process relies on filling a mold at high speeds with the alloy in the completely molten state, the thixomolding® process fills a mold with a thixotropic alloy in a semi-solid slurry state at a temperature between the liquidus and solidus temperatures. Ideally, the material should be ~30–65% solid rather than being completely liquid at the beginning of the injection process. Advantages of the thixomolding® process include a finer grain structure, lower porosity, improved dimensional accuracy, improved part-to part consistency, improved mechanical properties, particularly ductility in the component, the ability to reduce wall thickness for mass savings, and longer tool life due to lower process temperatures. The objective of this collaborative project between Oak Ridge National Laboratory, FCA US LLC, and Leggera Technologies was to develop one or more novel Mg alloys more suitable for thixomolding® automotive structural components than the current die-casting alloys used for this process. The primary interest was to improve ductility while maintaining tensile and fatigue strengths, as these are properties that are critical for use in body and chassis structural applications. Since good corrosion resistance is also desirable for this application, this property was also considered when evaluating promising alloy compositions. An initial evaluation of existing components thixomolded® using AM60 was performed and microstructure, and tensile properties were evaluated for the baseline alloy. Targets were established for ease of processing (characterized by the melting range defined as the difference between the liquidus and the solidus), strength, and ductility. Computational modeling was used to identify promising alloys and selected alloys were cast in laboratory scale heats. Properties measured from laboratory scale heats were used to down-select two alloys for further evaluation and component fabrication. Two alloys were prepared in industrial scale heats, cut into small pieces (chips), and thixomolding® trials were initiated. Trial components were successfully fabricated using one alloy composition, but it was concluded that further refinement of the thixomolding® process parameters are required to successfully fabricate component using second alloy. Microstructure and mechanical properties were evaluated on the material removed from the fabricated component and properties were compared to the baseline alloy. Although mechanical properties of the alloys showed improvement over the baseline alloy, it was determined that modifications to the thixomolding® process would result in better microstructure control with further improvement in properties leading to successful commercialization. A provisional patent application has already been filed on the new alloys developed as part of the project.

36 MATERIALS SCIENCE↗

Post-build stress-relief optimization for laser powder bed fusion 316H stainless steel

Nuclear energy remains a critical component of a diversified and efficient energy portfolio, offering reliable, high-capacity, and low-carbon power. However, in the U.S., aging infrastructure and the slow qualification and deployment of advanced materials and manufacturing techniques hinder progress in next-generation reactor technologies. This study explores the application of laser powder bed fusion (LPBF) additive manufacturing for stainless steel 316H, with a focus on optimizing post-build heat treatments to enhance material properties for high-temperature nuclear applications. The research targets the optimization of stress-relief temperatures to alleviate postbuild residual stresses, ensuring improvements in the microstructural corelated properties. A series of microstructural and mechanical evaluations were performed on LPBF-printed SS-316H samples which were subjected to annealing at temperatures varying between 650 °C and 850 °C. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy analyses revealed that increasing the heattreatment temperature accelerated dislocation recovery. Vickers microhardness measurements showed an initial reduction in values, followed by stabilization over extended durations at all the temperatures. While higher temperatures facilitated faster recovery, they also promoted carbide precipitation along grain and solidification cell boundaries, narrowing the safe processing window. In contrast, heat treatment at 650°C preserved the cellular substructure and enabled controlled carbide precipitation over time. In conclusion, these findings highlight the importance of time–temperature optimization and suggest that 650°C for up to 2 h provides the most favorable balance between recovery and carbide control for a stress-relief treatment.

316 stainless steel↗

Highly crystalline sodium manganese ferrocyanide microcubes for advanced sodium ion battery cathodes

The microstructure and morphology of the crystal play an important role in the physical and electrochemical properties of electrode materials. Here we report a highly crystalline microcube structure of Na-rich Prussian white Na 1.92 Mn[Fe(CN) 6 ] 0.98 for sodium ion battery cathodes. The obtained structure features high crystallinity of the monoclinic structure with an average cubic size of 3–5 μm. Because of the improvement on microstructural and electrical properties, the cathode design enables promising electrochemical performance. The electrode exhibits an outstanding rate performance with reversible capacities of 152.8 mA h g –1 (10 mA g –1 ), 128.1 mA h g –1 (100 mA g –1 ), 118.7 mA h g –1 (500 mA g –1 ) and 110.3 mA h g –1 (1000 mA g –1 ). It also exhibits a good cycling performance with a capacity retention of 82% after 500 cycles at 100 mA g –1 . More importantly, the XRD analysis reveals a highly reversible monoclinic–cubic–monoclinic structural evolution of the cathode upon Na + extraction/insertion. The good rate and cycling performance can be attributed to the robust crystal structure with few defects and fast Na + transfer kinetics. The high purity single crystal morphology can also reduce the side reactions on the electrode/electrolyte interface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Influence of Rare Earth Ce Additions on Microstructure and Mechanical Properties of Experimental Pipeline Steels

Herein, the effect of Ce additions ranging from 57 to 263 ppm is evaluated for an experimental pipeline steel. Compared to the Ce-free steel, progressive Ce additions result in a slightly refined microstructure, significantly improve transverse impact properties, and slightly increase strength. All these observations can be attributed to the gradual transformation of Mn sulfide and Mn–Si–Al oxide inclusions to Ce-containing oxide/sulfides. In particular, the inclusions consist exclusively of sub-5 μm spherical Ce 2 O 2 S particles upon near-stoichiometric additions of Ce, considering the oxygen and sulfur impurity level of the steel. In conclusion, the results suggest that Ce is a potentially promising alloying addition for next-generation pipeline steels by replacing overtly deleterious inclusions with potentially beneficial ones.

36 MATERIALS SCIENCE↗

Correlation of the energy product with evolution of the nanostructure in Y,Dy,Nd-(Fe,Co)-B magnetic alloy

The devitrification behavior of nanocrystalline MRE{sub 2}(Fe,Co){sub 14}B+ZrC (MRE = Nd+Y+Dy) was studied using differential scanning calorimetry (DSC), synchrotron high temperature x-ray diffraction, and analytical transmission electron microscopy (TEM) techniques. Alloy ribbons were melt spun at 25 m/s to obtain an amorphous structure. Optimum hard magnetic properties (B{sub r} = 7.2 kG, H{sub c} = 12.7 kOe and (BH){sub max} = 10.8 MG Oe) were obtained in ribbons annealed at 750 C for 15 min. A reduced annealing temperature of 638 C and holding time from 0 to 11 min were chosen based on DSC analysis. Large changes in both microstructure and hard magnetic properties were found in a narrow window of annealing time, 4.5-6 min, resulting in a dramatic increase in energy product, remanence and coercivity: 0.96 MG Oe, 5.2 kG, 2.7 kOe to 5.7 MG Oe, 7.2 kG, 8.5 kOe for (BH){sub max}, B{sub r} and H{sub c}, respectively. Energy dispersive x-ray spectroscopy and energy filtered TEM analyses indicate that Zr- and C-rich particles ({approx} 5 nm) and thin grain boundary layers (1-2 nm thick) are formed surrounding 2-14-1 hard phase grains when the annealing time is over 6 min. Further annealing resulted in a more distinct hard phase surrounded by a nonmagnetic grain boundary phase {approx} 1 nm in thickness. The thin grain boundary layer phase starts to disappear with annealing time over 11 min. The partitioning behavior of various elements at different annealing conditions appears to be associated with significant changes in magnetic properties, leading to an improved optimum microstructure.

36 MATERIALS SCIENCE↗

Boron Nitride-Driven Strengthening of Aluminum Composites via Friction Stir Processing

Friction stir welding and processing (FSW/P) has emerged as an effective solid-state joining technique for fabricating metal matrix composites (MMCs), offering improved mechanical properties through refined microstructural evolution. In this study, an aluminum-boron nitride nanoparticle (Al-BNNP) composite was synthesized via FSW, and its indentation-based mechanical properties were systematically evaluated. Microhardness mapping across the weld cross-section revealed a progressive increase in hardness toward the stir zone (SZ), attributed to severe plastic deformation, dynamic recrystallization (DRX), and the reinforcing effect of BNNPs. Profilometry-based indentation plastometry (PIP) inferred yield strength (YS) demonstrates a 47.8% increase compared to the base metal (BM) and a 75% improvement compared to FSP pure aluminum reported in literature. This enhancement is attributed to strengthening mechanisms, including grain boundary pinning, load transfer, and increased dislocation density. The strain rate sensitivity (SRS) measurements at the nanoscale demonstrated a substantial decrease in the SZ, correlated with ultrafine grain structures and strong BNNP-matrix interactions. Activation volume analysis revealed a significant reduction in the SZ, suggesting that dislocation motion is increasingly restricted by dislocation-dislocation and dislocation-particle interactions. These findings suggest that incorporating BNNPs in FSW/P enables tailoring the microstructure without thermal degradation of the secondary particles, thereby significantly enhancing the mechanical performance of aluminum composites, particularly for structural applications in aerospace and automotive industries.

Aluminum↗