Search NASA⌕ Search

SEARCH · Search NASA

Results for “interface converter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

The application of standardized control and interface circuits to three dc to dc power converters.

Standardized control and interface circuits were applied to the three most commonly used dc to dc converters: the buck-boost converter, the series-switching buck regulator, and the pulse-modulated parallel inverter. The two-loop ASDTIC regulation control concept was implemented by using a common analog control signal processor and a novel digital control signal processor. This resulted in control circuit standardization and superior static and dynamic performance of the three dc-to-dc converters. Power components stress control, through active peak current limiting and recovery of switching losses, was applied to enhance reliability and converter efficiency.

Yu, Y.↗
NASA NTRS1988

Wideband Digital Interface Unit

Signals converted from serial to parallel and buffered for input to computer. Wideband digital interface unit converts serial input data bits to 16-bit words and feeds them as needed to host computer.

Baltau, William M.↗
NASA NTRS1981

Structure of the lunar crust at highland site Apollo Station 16

The seismic crustal structure of the moon is known in the region of Oceanus Procellarum from the analysis of artificial impact data. To extend this knowledge we have used data from natural lunar seismic events to search for secondary seismic wave arrivals in the form of peg-leg multiples caused by reflections at crustal interfaces and converted arrivals caused by refractions at crustal interfaces. A polarization filter has been applied to the data to enhance the rectilinear particle motion expected for the onset of these body wave arrivals in the scattered coda of lunar seismograms. The results of this work tentatively indicate that the highland site at station 16 has a 75 km thick crust with an intermediate 20 km interface, compared to the 60 km crust and 20 km interface in Oceanus Procellarum, a mare region. Since the 20 km upper crust appears to exist at both highland and mare sites, it probably does not represent a mare basalt layer but rather a more general feature of the crust. Crustal thickness may partially control elevation by isostasy.

Goins, N. R.↗
NASA NTRS1993

DC-DC power converter research for Orbiter/Station power exchange

This project was to produce innovative DC-DC power converter concepts which are appropriate for the power exchange between the Orbiter and the Space Station Freedom (SSF). The new converters must interface three regulated power buses on SSF, which are at different voltages, with three fuel cell power buses on the Orbiter which can be at different voltages and should be tracked independently. Power exchange is to be bi-directional between the SSF and the Orbiter. The new converters must satisfy the above operational requirements with better weight, volume, efficiency, and reliability than is available from the present conventional technology. Two families of zero current DC-DC converters were developed and successfully adapted to this application. Most of the converters developed are new and are presented.

Ehsani, M.↗
NASA NTRS1973

A slow-speed multiple-channel analog-to-digital data logging system

The system was developed to record from one up to a maximum of sixteen channels of analog data onto magnetic tape. Each analog channel of data can be sampled at rates of 1, 2, 6, 12, or 60 times per minute. The system is divided into three subunits: a digital clock, an incremental magnetic tape recorder, and a sequential converter. The interfacing requirements of these subunits are presented.

Lloyd, T. C.↗
NASA NTRS1993

Laser-enhanced synthesis and processing of diamond films from liquid hydrocarbons

We report synthesis of diamond films by pulsed laser irradiation on copper substrate immersed into liquid benzene. It is envisaged that carbon released from benzene at the liquid-solid interface is converted into diamond as a result of rapid quenching from a high temperature. The diamond crystallites were characterized using high resolution transmission electron microscopy imaging and electron diffraction techniques. Growth of thicker diamond films by subsequent chemical vapor deposition has been investigated by transmission and scanning electron microscopy techniques. Thin diamond film deposited during liquid phase provided seed for diamond growth during subsequent chemical vapor deposition.

Singh, Jogender↗
NASA NTRS2023

Development of Two High-Energy Bus ‘Cores’ for Rapid Support of Low-TRL and Educational Payloads: A Software-Configured EPS Combined with Flexible C&DH

For several years the TechEdSat flight series (TES-n), developed by the Nano Orbital Workshop (NOW) group at NASA Ames, has relied upon an in-house developed unit to serve both EPS (Electrical Power System) and C&DH (Command and Data Handling) roles along with low data-rate telemetry functions, i.e., serving as the ‘core’ of the spacecraft bus. This ‘core’ has a considerable task given the rapid cadence of the TES program and the typically low-TRL of payloads; configurability and compatibility are key to prevent mission-specific hardware. However, at only 15 watts the current core has become insufficient to support the program’s growing missions and increasingly demanding payloads. To this end, the NOW program is developing new cores to support two TES mission classes: a single-PCB ‘MiniCore’ designed to support 80-watt missions 6U or smaller in LEO, and a three-PCB, radiation-tolerant ‘StackCore’ designed to support 6U and larger missions over 500 watts in LEO and beyond. The ‘MiniCore’ design consists of three main segments: a processor-agnostic C&DH, a software-configured EPS, and a backup low data-rate radio. The design philosophy was to enable rapid-manufacture in a turbulent supply chain, hence the design consists of COTS parts with a focus on those able to be drop-in replaced with radiation-tolerant versions when demanded by the mission. As a single PC-104 sized circuit board, power density and ease of integration also dominated design, demanding the use of modern features such as single-point USB-C for easy charging and monitoring of the spacecraft on the ground. The ‘MiniCore’ can support 80 watts of load, 140 watt-hours of storage, and over 20 watts of optimized solar generation with extensive power monitoring throughout. The ‘MiniCore’ supports one battery pack, six solar-panels, six loads, five actuators, Iridium SBD, and an internal 802.15.4 network. Additionally, the processor-agnostic design can accept any PJRC Teensy 3.x or Adafruit Feather microcontroller unit to enable processor scaling with mission requirements or environment. It is expected a development unit of this design will be completed before conference. The ‘StackCore’ design consists of three stacked PC-104 sized circuit boards: one dedicated to power generation and storage, one dedicated to power distribution, and one dedicated to C&DH tasks. This delineation is necessary to support the transition from highly integrated ICs to discrete analog circuitry, enabling a primarily analog control power system able to operate without software in a radiation environment with finer monitoring compared to the ‘MiniCore’ design. The planned base architecture supports over 500 watts of load, 250 watt-hours of storage, and over 80 watts of optimized solar generation. The power distribution board allows for the use of daughter cards hosting custom converters or interfaces for payloads, in addition to the software-configured supplies used on the ‘MiniCore’. This core stack will be managed by a Vorago ARM M4 microcontroller and support the same wireless communications as the ‘MiniCore’, with optional integration of a NOW S-band radio and attitude determination sensors for ‘black box’ functionality. It is expected the prototype will still be in development during conference.

Spacecraft↗
NASA NTRSDate not supplied

Development of Two High-Energy Bus ‘Cores’ for Rapid Support of Low-TRL and Educational Payloads: A Software-Configured EPS Combined with Flexible C&DH

For several years the TechEdSat flight series (TES-n), developed by the Nano Orbital Workshop (NOW) group at NASA Ames, has relied upon an in-house developed unit to serve both EPS (Electrical Power System) and C&DH (Command and Data Handling) roles along with low data-rate telemetry functions, i.e., serving as the ‘core’ of the spacecraft bus. This ‘core’ has a considerable task given the rapid cadence of the TES program and the typically low-TRL of payloads; configurability and compatibility are key to prevent mission-specific hardware. However, at only 15 watts the current core has become insufficient to support the program’s growing missions and increasingly demanding payloads. To this end, the NOW program is developing new cores to support two TES mission classes: a single-PCB ‘MiniCore’ designed to support 80-watt missions 6U or smaller in LEO, and a three-PCB, radiation-tolerant ‘StackCore’ designed to support 6U and larger missions over 500 watts in LEO and beyond. The ‘MiniCore’ design consists of three main segments: a processor-agnostic C&DH, a software-configured EPS, and a backup low data-rate radio. The design philosophy was to enable rapid-manufacture in a turbulent supply chain, hence the design consists of COTS parts with a focus on those able to be drop-in replaced with radiation-tolerant versions when demanded by the mission. As a single PC-104 sized circuit board, power density and ease of integration also dominated design, demanding the use of modern features such as single-point USB-C for easy charging and monitoring of the spacecraft on the ground. The ‘MiniCore’ can support 80 watts of load, 140 watt-hours of storage, and over 20 watts of optimized solar generation with extensive power monitoring throughout. The ‘MiniCore’ supports one battery pack, six solar-panels, six loads, five actuators, Iridium SBD, and an internal 802.15.4 network. Additionally, the processor-agnostic design can accept any PJRC Teensy 3.x or Adafruit Feather microcontroller unit to enable processor scaling with mission requirements or environment. It is expected a development unit of this design will be completed before conference. The ‘StackCore’ design consists of three stacked PC-104 sized circuit boards: one dedicated to power generation and storage, one dedicated to power distribution, and one dedicated to C&DH tasks. This delineation is necessary to support the transition from highly integrated ICs to discrete analog circuitry, enabling a primarily analog control power system able to operate without software in a radiation environment with finer monitoring compared to the ‘MiniCore’ design. The planned base architecture supports over 500 watts of load, 250 watt-hours of storage, and over 80 watts of optimized solar generation. The power distribution board allows for the use of daughter cards hosting custom converters or interfaces for payloads, in addition to the software-configured supplies used on the ‘MiniCore’. This core stack will be managed by a Vorago ARM M4 microcontroller and support the same wireless communications as the ‘MiniCore’, with optional integration of a NOW S-band radio and attitude determination sensors for ‘black box’ functionality. It is expected the prototype will still be in development during conference.

Spacecraft↗
NASA NTRSDate not supplied

Development of Two High-Energy Bus ‘Cores’

For several years the TechEdSat flight series (TES-n), developed by the Nano Orbital Workshop (NOW) group at NASA Ames, has relied upon an in-house developed unit to serve both EPS (Electrical Power System) and C&DH (Command and Data Handling) roles along with low data-rate telemetry functions, i.e., serving as the ‘core’ of the spacecraft bus. This ‘core’ has a considerable task given the rapid cadence of the TES program and the typically low-TRL of payloads; configurability and compatibility are key to prevent mission-specific hardware. However, at only 15 watts the current core has become insufficient to support the program’s growing missions and increasingly demanding payloads. To this end, the NOW program is developing new cores to support two TES mission classes: a single-PCB ‘MiniCore’ designed to support 80-watt missions 6U or smaller in LEO, and a three-PCB, radiation-tolerant ‘StackCore’ designed to support 6U and larger missions over 500 watts in LEO and beyond. The ‘MiniCore’ design consists of three main segments: a processor-agnostic C&DH, a software-configured EPS, and a backup low data-rate radio. The design philosophy was to enable rapid-manufacture in a turbulent supply chain, hence the design consists of COTS parts with a focus on those able to be drop-in replaced with radiation-tolerant versions when demanded by the mission. As a single PC-104 sized circuit board, power density and ease of integration also dominated design, demanding the use of modern features such as single-point USB-C for easy charging and monitoring of the spacecraft on the ground. The ‘MiniCore’ can support 80 watts of load, 140 watt-hours of storage, and over 20 watts of optimized solar generation with extensive power monitoring throughout. The ‘MiniCore’ supports one battery pack, six solar-panels, six loads, five actuators, Iridium SBD, and an internal 802.15.4 network. Additionally, the processor-agnostic design can accept any PJRC Teensy 3.x or Adafruit Feather microcontroller unit to enable processor scaling with mission requirements or environment. It is expected a development unit of this design will be completed before conference. The ‘StackCore’ design consists of three stacked PC-104 sized circuit boards: one dedicated to power generation and storage, one dedicated to power distribution, and one dedicated to C&DH tasks. This delineation is necessary to support the transition from highly integrated ICs to discrete analog circuitry, enabling a primarily analog control power system able to operate without software in a radiation environment with finer monitoring compared to the ‘MiniCore’ design. The planned base architecture supports over 500 watts of load, 250 watt-hours of storage, and over 80 watts of optimized solar generation. The power distribution board allows for the use of daughter cards hosting custom converters or interfaces for payloads, in addition to the software-configured supplies used on the ‘MiniCore’. This core stack will be managed by a Vorago ARM M4 microcontroller and support the same wireless communications as the ‘MiniCore’, with optional integration of a NOW S-band radio and attitude determination sensors for ‘black box’ functionality. It is expected the prototype will still be in development during conference.

Avery Brock↗
NASA NTRS1980

Biased-receiver digital interface

Coupling circuits converts TTL signals to higher voltage, higher current logic with good noise rejection. Depending on selected components, circuit may also be adapted to low-power applications.

Fitzgerald, F. C.↗
NASA NTRS1990

Continuation of research into software for space operations support, volume 1

A prototype workstation executive called the Hardware Independent Software Development Environment (HISDE) was developed. Software technologies relevant to workstation executives were researched and evaluated and HISDE was used as a test bed for prototyping efforts. New X Windows software concepts and technology were introduced into workstation executives and related applications. The four research efforts performed included: (1) Research into the usability and efficiency of Motif (an X Windows based graphic user interface) which consisted of converting the existing Athena widget based HISDE user interface to Motif demonstrating the usability of Motif and providing insight into the level of effort required to translate an application from widget to another; (2) Prototype a real time data display widget which consisted of research methods for and prototyping the selected method of displaying textual values in an efficient manner; (3) X Windows performance evaluation which consisted of a series of performance measurements which demonstrated the ability of low level X Windows to display textural information; (4) Convert the Display Manager to X Window/Motif which is the application used by NASA for data display during operational mode.

Collier, Mark D.↗
NASA NTRS2004

The Lewice Console

Lewice (LEWis ICE accretion program) is software used by literally hundreds of users in the aeronautics community for predicting ice shapes, collections efficiencies, and anti-icing heat requirements for aircraft. LEWICE performs its analysis in minutes on a desktop PC, allowing the user to run several parameter studies for design purposes. The ice shape predictions have been used to assess performance degradation both as an input to a CFD program or experimentally in flight or in a wind tunnel. This information is important to ensure an airplane s safe passage through an icing cloud. Currently, Lewice runs as a DOS program that accepts many different inputs such as cloud conditions, wing shapes, and thermal deicing inputs. Usually, such experimental data is stored in spreadsheets. However, Lewice inputs are text files; therefore, they must be generated by the user. Lewice s outputs (collection efficiency, ice shapes and thicknesses) are also text files; to plot the data, users must generate a spreadsheet with this output. Because all Lewice J/O is in the form of text files, using Lewice can be tricky and time-consuming. Our goal was to improve Lewice s usability by creating a user interface that would automatically generate Lewice input from a spreadsheet and automatically put Lewice output into spreadsheets with charts. Additionally, this user interface would automatically convert units (as Lewice only accepts input in certain units) and offer several output options. I call this program the Lewice Console. The Lewice Console is an easy to use interface for Lewice written in Visual Basic. It allows users to run Lewice given a spreadsheet listing experimental conditions. It automatically generates the input to Lewice, does necessary unit conversions, runs Lewice, and produces a spreadsheet with charts plotting the data. It allows users to import data from previously generated Lewice inputs into a spreadsheet. It also allows users to batch run Lewice on several different inputs to automatically generate multiple output spreadsheets. You can also generate plots of actual data vs. experimental data. These capabilities are just the beginning for the Lewice Console. Lewice is capable of running a full deicing experiment given a geometry and heating apparatus information. However, users find it difficult to run such experiments due to the number of inputs and the difficult input file format. The Lewice Console would simplify experiment generation by allowing the user to interactively draw a geometry, place heating apparatus, and specify information about each part. The input to Lewice would be automatically generated from the experiment the user draws on the screen. The Lewice Console would simplify the experiment building process. Currently, Lewice runs as a DOS program that accepts many different inputs such as

Armstrong, Aaron E.↗
NASA NTRS1994

Development of a Power Electronics Unit for the Space Station Plasma Contactor

A hollow cathode plasma contactor has been baselined as a charge control device for the Space Station (SS) to prevent deleterious interactions of coated structural components with the ambient plasma. NASA LeRC Work Package 4 initiated the development of a plasma contactor system comprised of a Power Electronics Unit (PEU), an Expellant Management Unit (EMU), a command and data interface, and a Plasma Contactor Unit (PCU). A breadboard PEU was designed and fabricated. The breadboard PEU contains a cathode heater and discharge power supply, which were required to operate the PCU, a control and auxiliary power converter, an EMU interface, a command and telemetry interface, and a controller. The cathode heater and discharge supplies utilized a push-pull topology with a switching frequency of 20 kHz and pulse-width-modulated (PWM) control. A pulse ignition circuit derived from that used in arcjet power processors was incorporated in the discharge supply for discharge ignition. An 8088 based microcontroller was utilized in the breadboard model to provide a flexible platform for controller development with a simple command/data interface incorporating a direct connection to SS Mulitplexer/Demultiplexer (MDM) analog and digital I/O cards. Incorporating this in the flight model would eliminate the hardware and software overhead associated with a 1553 serial interface. The PEU autonomously operated the plasma contactor based on command inputs and was successfully integrated with a prototype plasma contactor unit demonstrating reliable ignition of the discharge and steady-state operation.

Hamley, John A.↗
NASA NTRS1966

Pair production of plasma vortices.

Plasma vortex filaments produced in pairs as shown by image converter photographs of interfaces between magnetic field and accelerated plasma

VORTEX GENERATOR↗
NASA NTRS1983

Two-Wire to Four-Wire Audio Converter

Simple circuit provides interface between normally incompatible voicecommunication lines. Circuit maintains 40 dB of isolation between input and output halves of four-wire line permitting two-wire line to be connected. Balancing potentiometer, Rg, adjusts gain of IC2 to null feed through from input to output. Adjustment is done on workbench just after assembly.

Talley, G. L., Jr↗
NASA NTRS1994

Voice and video transmission using XTP and FDDI

The use of Xpress Transfer Protocol (XTP) and Fiber Distributed Data Interface (FDDI) provides a high speed and high performance network solution to multimedia transmission that requires high bandwidth. FDDI is an ANSI and ISO standard for a MAC and physical layer protocol that provides a signaling rate of 100 Mbits/sec and fault tolerance. XTP is a transport and network layer protocol designed for high performance and efficiency and is the heart of the SAFENET Lightweight Suite for systems that require performance or realtime communications. The testbed consists of several commercially available Intel based i486 PC's containing off-the-shelf FDDI cards, audio analog-digital converter cards, video interface cards, and XTP software. Unicast, multicast, and duplex audio transmission experiments have been performed using XTP software. Unicast and multicast video transmission is in progress. Several potential commercial applications are described.

Drummond, John↗
NASA NTRS1974

A computer-controlled, on-board data acquisition system for wind-tunnel testing

A computer-controlled data acquisition system has been developed for the 40x80-foot wind tunnel at Ames Research Center. The system, consisting of several small onboard units installed in the model and a data-managing, data-displaying ground station, is capable of sampling up to 256 channels of raw data at a total sample rate of 128,000 samples/sec. Complete signal conditioning is contained within the on-board units. The sampling sequence and channel gain selection is completely random and under total control of the ground station. Outputs include a bar-graph display, digital-to-analog converters, and digital interface to the tunnel's central computer, an SEL 840MP. The system can be run stand-alone or under the control of the SEL 840MP.

Finger, H. J.↗
NASA NTRS1977

Some studies on a solid state sulfur probe for coal gasification systems

Measurements on the solid electrolyte cell (Ar + H(2) + H(2)S/CaS + CaF(2) + (Pt)//CaF(2)//(Pt) + CaF(2) + CaS/H(2) + H(2)+Ar) show that the emf of the cell is directly related to the difference in sulfur potentials established at the Ar + H(2) + H(2)S/electrode interfaces. The electrodes convert the sulfur potential gradient across the calcium fluoride electrolyte into an equivalent fluorine potential gradient. Response time of the probe varies from approximately 9 hr at 990 K to 2.5 hr at 1225 K. The conversion of calcium sulfide and/or calcium fluoride into calcium oxide is not a problem anticipated in commercial coal gasification systems. Suggestions are presented for improving the cell for such commercial applications.

Jacob, K. T.↗