Search NASA⌕ Search

SEARCH · Search NASA

Results for “interfacial area”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Two-Fluid Models and Interfacial Area Transport in Microgravity Condition

The objective of the present study is to develop a two-fluid model formulation with interfacial area transport equation applicable for microgravity conditions. The new model is expected to make a leapfrog improvement by furnishing the constitutive relations for the interfacial interaction terms with the interfacial area transport equation, which can dynamically model the changes of the interfacial structures. In the first year of this three-year project supported by the U.S. NASA, Office of Biological and Physics Research, the primary focus is to design and construct a ground-based, microgravity two-phase flow simulation facility, in which two immiscible fluids with close density will be used. In predicting the two-phase flow behaviors in any two-phase flow system, the interfacial transfer terms are among the most essential factors in the modeling. These interfacial transfer terms in a two-fluid model specify the rate of phase change, momentum exchange, and energy transfer at the interface between the two phases. For the two-phase flow under the microgravity condition, the stability of the fluid particle interface and the interfacial structures are quite different from those under normal gravity condition. The flow structure may not reach an equilibrium condition and the two fluids may be loosely coupled such that the inertia terms of each fluid should be considered separately by use of the two-fluid model. Previous studies indicated that, unless phase-interaction terms are accurately modeled in the two-fluid model, the complex modeling does not necessarily warrant an accurate solution.

Ishii, Mamoru↗

On the prediction of horizontal bubbly flows using the interfacial area transport equation

To solve the two-fluid model utilized in current nuclear reactor system analysis codes, the interfacial area concentration (a i) is estimated through flow regime dependent correlations that rely on static regime transition criteria. This approach does not capture the continuous evolution of the interfacial structures, and thus, it can pose numerical issues near the transition boundaries. The interfacial area transport equation (IATE) can help address these shortcomings by providing a dynamic prediction of a a{sub i} through mechanistic source and sink terms that account for bubble coalescence and breakup. Most of the previous work for this approach has focused on vertical two-phase flow. However, relatively few studies have been performed for horizontal two-phase flows, where buoyancy strongly affects the phase distribution. To develop a one-dimensional, area-averaged form of the IATE for adiabatic, horizontal bubbly flows the following considerations are necessary: (1) pressure drop estimation, (2) bubble velocity/void fraction estimation, (3) determination of bubble interaction mechanisms, and (4) treatment of the asymmetric phase distribution. In the current work, treatment of the asymmetric phase distribution is presented. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Predictions of one-group interfacial area transport in TRACE

In current nuclear reactor system analysis codes utilizing the two-fluid model, flow regime dependent correlations are used to specify the interfacial area concentration (a i). This approach does not capture the continuous evolution of the interfacial structures, and thus, it can pose issues near the transition boundaries. Consequently, a pilot version of the system analysis code TRACE is being developed that employs the interfacial area transport equation (IATE). In this approach, dynamic estimation of a i is provided through mechanistic models for bubble coalescence and breakup. The implementation of the adiabatic, one-group IATE into TRACE is assessed against experimental data from 50 air-water, two-phase flow conditions in pipes ranging in inner diameter from 2.54 to 20.32 cm for both vertical co-current upward and downward flows. Predictions of pressure, void fraction, bubble velocity, and a i data are made. TRACE employing the conventional flow regime-based approach is found to underestimate a i and can only predict linear trends since the calculation is governed by the pressure. Furthermore, trends opposite to that of the data are predicted for some conditions. In contrast, TRACE with the one-group IATE demonstrates a significant improvement in predicting the experimental data with an average disagreement of {+-} 13%. Additionally, TRACE with the one-group IATE is capable of predicting nonlinear axial development of a, by accounting for various bubble interaction mechanisms, such as coalescence and disintegration. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Sensitivity Analysis of Fluid–Fluid Interfacial Area, Phase Saturation and Phase Connectivity on Relative Permeability Estimation Using Machine Learning Algorithms

Recent studies have shown that relative permeability can be modeled as a state function which is independent of flow direction and dependent upon phase saturation (S), phase connectivity (X), and fluid–fluid interfacial area (A). This study evaluates the impact of each of the three state parameters (S, X, and A) in the estimation of relative permeability. The relative importance of the three state parameters in four separate quadrants of S-X-A space was evaluated using a machine learning algorithm (out-of-bag predictor importance method). The results show that relative permeability is sensitive to all the three parameters, S, X, and A, with varying magnitudes in each of the four quadrants at a constant value of wettability. We observe that the wetting-phase relative permeability is most sensitive to saturation, while the non-wetting phase is most sensitive to phase connectivity. Although the least important, fluid–fluid interfacial area is still important to make the relative permeability a more exact state function.

47 OTHER INSTRUMENTATION↗

Improving performance of two-group interfacial area transport equation models using genetic algorithms and high resolution experimental data

In the two-fluid transport model, the coupling of mass, momentum and energy transfer between phases is highly dependent on interfacial area transfer terms. Several research efforts in the past have been focused on the development of an interfacial area transport equation model (IATE), in order to eliminate the drawbacks of static flow regime maps currently used in best-estimate thermal-hydraulic system codes. The IATE attempts to model the dynamics that are involved in two phase flows by accounting for the different interaction mechanisms affecting bubble transport in the flow. In general, current IATE models perform poorly in high void fraction flow regimes. As both models depend on closure relations that require empirically determined coefficients, a genetic algorithm is implemented to study their optimization. The preliminary study indicates that improvements are achievable by application of the genetic algorithm. Optimization of coefficients for an entire set of high-resolution wire mesh sensor (WMS) data provided a single set of optimal coefficients. The application of WMS-optimized coefficients to external tests improved IATE performance for similar hydraulic diameters and provided a neutral change in performance for significantly smaller/larger hydraulic diameters. This is a crucial outcome as an optimized set of coefficients that provide significant improvement for a subset of experimental data - is shown to benefit performance in external data for which the coefficients are not specifically optimized. (authors)

42 ENGINEERING↗

The Interfacial-Area-Based Relative Permeability Function

CH2M Hill Plateau Remediation Company (CHPRC) requested the services of the Pacific Northwest National Laboratory (PNNL) to provide technical support for the Remediation Decision Support (RDS) activity within the Soil & Groundwater Remediation Project. A portion of the support provided in FY2009, was to extend the soil unsaturated hydraulic conductivity using an alternative approach. This alternative approach incorporates the Brooks and Corey (1964), van Genuchten (1980), and a modified van Genuchten water-retention models into the interfacial-area-based relative permeability model presented by Embid (1997). The general performance of the incorporated models is shown using typical hydraulic parameters. The relative permeability models for the wetting phase were further examined using data from literature. Results indicate that the interfacial-area-based model can describe the relative permeability of the wetting phase reasonably well.

54 ENVIRONMENTAL SCIENCES↗

Experimentally Measured Interfacial Area during Gas Injection into Saturated Porous Media: An Air Sparging Analogy

The amount of interfacial area (awn) between air and subsurface liquids during air-sparging can limit the rate of site remediation. Lateral movement within porous media could be encountered during air-sparging operations when air moves along the bottom of a low-permeability lens. This study was conducted to directly measure the amount of awn between air and water flowing within a bench-scale porous flow cell during the lateral movement of air along the upper edge of the cell during air injections into an initially water-saturated flow cell. Four different cell orientations were used to evaluate the effect of air injection rates and porous media geometries on the amount of awn between fluids. Air was injected at flow rates that varied by three orders of magnitude, and for each flow cellover this range of injection rates little change in awn was noted. A wider variation in awn was observed when air moved through different regions for the different flow cell orientations. These results are in good agreement with the experimental findings of Waduge et al. (2007), who performed experiments in a larger sand-pack flow cell, and determined that air-sparging efficiency is nearly independent of flow rate but highly dependent on the porous structure. By directly measuring the awn, and showing that awn does not vary greatly with changes in injection rate, we show that the lack of improvement to remediation rates is because there is a weak dependence of the awn on the air injection rate.

58 GEOSCIENCES↗

Characterizing the pore-scale impacts of enhanced-solubilization solutions on organic-liquid morphology and fluid-fluid interfacial area with microtomography

Synchrotron X-ray microtomography was used to directly quantify the impact of enhanced-solubilization solutions on mobilization of a non-wetting fluid in a natural porous medium. Polyoxyethylene sorbitan monooleate (tween 80), hydroxypropyl-β-cyclodextrin (HPCD), sodium dodecyl sulfate (SDS), and ethanol were used as the solubilization reagents. Tetrachloroethene (PCE) was used as the entrapped organic immiscible liquid. Microtomography images were collected prior to and after successive floods with each reagent solution. The total trapping number was varied by more than three orders of magnitude by changing the velocity and viscosity of the aqueous phase as well as the interfacial tension between fluid phases. The results were compared to those obtained from equivalent experiments conducted with water flooding. Inspection of images indicated that mobilization caused a change in PCE morphology and distribution for all reagents with the exception of HPCD, for which a lower trapping number was determined compared to the other experiments. Mobilization of organic liquid was observed at total trapping numbers that were consistent with prior work. The enhanced-solubilization solutions had minimal impact on the configuration or magnitude of fluid-fluid interfacial area.

Interfacial area↗

Laser Ablation Increases PEM/Catalyst Interfacial Area

An investigational method of improving the performance of a fuel cell that contains a polymer-electrolyte membrane (PEM) is based on the concept of roughening the surface of the PEM, prior to deposition of a thin layer of catalyst, in order to increase the PEM/catalyst interfacial area and thereby increase the degree of utilization of the catalyst. The roughening is done by means of laser ablation under carefully controlled conditions. Next, the roughened membrane surface is coated with the thin layer of catalyst (which is typically platinum), then sandwiched between two electrode/catalyst structures to form a membrane/ele c t - rode assembly. The feasibility of the roughening technique was demonstrated in experiments in which proton-conducting membranes made of a perfluorosulfonic acid-based hydrophilic, protonconducting polymer were ablated by use of femtosecond laser pulses. It was found that when proper combinations of the pulse intensity, pulse-repetition rate, and number of repetitions was chosen, the initially flat, smooth membrane surfaces became roughened to such an extent as to be converted to networks of nodules interconnected by filaments (see Figure 1). In further experiments, electrochemical impedance spectroscopy (EIS) was performed on a pristine (smooth) membrane and on two laser-roughened membranes after the membranes were coated with platinum on both sides. Some preliminary EIS data were interpreted as showing that notwithstanding the potential for laser-induced damage, the bulk conductivities of the membranes were not diminished in the roughening process. Other preliminary EIS data (see Figure 2) were interpreted as signifying that the surface areas of the laser-roughened membranes were significantly greater than those of the smooth membrane. Moreover, elemental analyses showed that the sulfur-containing molecular groups necessary for proton conduction remained intact, even near the laser-roughened surfaces. These preliminary results can be taken as indications that laser-roughened PEMs should function well in fuel cells and, in particular, should exhibit current and power densities greater than those attainable by use of smooth membranes.

Whitacre, Jay↗

Representative elementary volume estimation for porosity, moisture saturation, and air-water interfacial areas in unsaturated porous media: Data quality implications

Achieving a representative elementary volume (REV) has become a de facto criterion for demonstrating the quality of {mu}CT measurements in porous media systems. However, the data quality implications of an REV requirement have not been previously examined. In this work, deterministic REVs for porosity, moisture saturation (S{sub W}), and air-water interfacial area (A{sub I}) were estimated using a set of 49 {mu}CT images of eight unsaturated homogeneous porous media with heterogeneity in moisture distributions present in varying degrees. Estimated porosity REVs were <8 mm{sup 3} for all cases, smaller than typical CT image sizes ({approx}100 mm{sup 3}). Estimated S{sub W} and A{sub I} REVs were <55 mm{sup 3} for cases with homogeneous moisture distributions but could not be estimated for cases with heterogeneous moisture distributions, due to the absence of a distinct 'REV plateau' within the maximum imaged volume. Conventionally, S{sub W} and A{sub I} data from such non-REV cases would be excluded. The implications of excluding data on the basis of REV were examined by comparing A{sub I}-S{sub W} data measured on image windows of increasing size against the expected linear A{sub I}-S{sub W} relationship. At measurement scales exceeding porosity REV, random fluctuations in A{sub I}-S{sub W} data were excluded, even for cases containing heterogeneous moisture distributions. In contrast, requiring measurement scales to exceed S{sub W} and A{sub I} REV appeared overly restrictive and resulted in visible loss of reliable A{sub I}-S{sub W} data. We attribute these findings to overestimation of REVs due to inherently problematic estimation of deterministic REVs in real systems. Implications of these findings for ensuring CT data quality and the efficient use of CT data are discussed.

99 GENERAL AND MISCELLANEOUS↗

Hybrid multiphase CFD simulation for liquid-liquid interfacial area prediction in annular centrifugal contactors

Liquid-liquid contacting equipment used in solvent extraction processes has the dual purpose of mixing and separating two immiscible fluids. Consequently, such devices inherently encompass a wide variety of multiphase flow regimes. A hybrid multiphase computational fluid dynamics (CFD) solver which combines the Eulerian multi-fluid method with VOF (volume of fluid) sharp interface capturing has been developed for application to annular centrifugal contactors. This solver has been extended to enable prediction of mean droplet size and liquid-liquid interfacial area through a single moment population balance method. Simulations of liquid-liquid mixing in a simplified geometry and a model annular centrifugal contactor are reported with droplet breakup/coalescence models being calibrated versus available experimental data. Quantitative comparison is made for two different housing vane geometries and it is found that the predicted droplet size is significantly smaller for vane geometries which result in higher annular liquid holdup.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Interfacial Area Transport through Vertical-Downward Elbows in Air-water Two-phase Flow

In the study of two-phase flow, models are often developed by the data acquired in a test section with fixed orientation and with no flow restrictions. In view of practical nuclear reactor systems, however, two-phase flow through flow restrictions is important. Flow restrictions and orientations can alter both global and local two-phase flow parameters such as: cause additional pressure loss; alter the flow regime transition; change bubble distributions; affect the bubble velocity and the bubble interaction mechanisms. However, there is insufficient database and predictive models that can account for such effects. In view of above, the objectives of the current study are: (1) to establish database for local and global two-phase flow parameters downstream of a horizontal-to-vertical glass elbow with a non-dimensional radius of curvature, R{sub c}/D, of three, (2) to develop predictive models in the elbow region, and (3) to apply the developed model to the interfacial area transport equation (IATE) and evaluate it in elbow regions. (authors)

42 ENGINEERING↗

Interfacial area transport and regime transition in combinatorial channels

This study investigates the geometric effects of 90-degree vertical elbows and flow configurations in two-phase flow. The study shows that the elbows make a significant effect on the transport characteristics of two-phase flow, which includes the changes in interfacial structures, bubble interaction mechanisms and flow regime transition. The effect of the elbows is characterized for global and local two-phase flow parameters. The global two-phase flow parameters include two-phase pressure, interfacial structures and flow regime transition. In order to characterize the frictional pressure drop and minor loss across the vertical elbows, pressure measurements are obtained across the test section over a wide range of flow conditions in both single-phase and two-phase flow conditions.

42 ENGINEERING↗