Search NASA⌕ Search

SEARCH · Search NASA

Results for “intermediate solids”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Synthesis of Y1BaCu3O(x) superconducting powders by intermediate phase reactions

A procedure for synthesizing Y1Ba2Cu3O(x) by solid state reactions was developed. The method is based on the use of barium compounds, previously synthesized, as intermediate phases for the process. The reaction kinetics of this procedure were established between 860 C and 920 C. The crystal structure and the presence of second phases were studied by means of XRD. The sintering behavior and ceramic parameters were also determined. The orthorhombic type-I structure was obtained on the synthesized bodies after a cooling cycle in an air atmosphere. Superconducting transition took place at 91 K. Sintering densities higher than 95 percent D sub th were attained at temperatures below 940 C.

Moure, C.↗
NASA NTRS1970

Feeding man in space

Semi-solid, dehydrated, rehydratable, thermally stabilized wet, and intermediate moisture food development for space flights

Hollender, H. A.↗
NASA NTRS1975

Storage Stability and Improvement of Intermediate Moisture Foods, Phase 3

Methods were determined for the improvement of shelf-life stability of intermediate moisture foods (IMF). Microbial challenge studies showed that protection against molds and Staphylococcus aureus could be achieved by a combination of antimicrobial agents, humectants and food acids. Potassium sorbate and propylene glycol gave the best results. It was also confirmed that the maximum in heat resistance shown by vegetative pathogens at intermediate water activities also occurred in a solid food. Glycols and sorbitol both achieve browning inhibition because of their action as a medium for reaction and effect on viscosity of the adsorbed phase. Chemical availability results showed rapid lysine loss before visual discoloration occurred. This is being confirmed with a biological test using Tetrahymena pyriformis W. Accelerated temperature tests show that effectiveness of food antioxidants against rancidity development can be predicted; however, the protection factor changes with temperature. BHA was found to be the best antioxidant for iron catalyzed oxidation.

Labuza, T. P.↗
NASA NTRS1986

Estimated heats of fusion of fluoride salt mixtures suitable for thermal energy storage applications

The heats of fusion of several fluoride salt mixtures with melting points greater than 973 K were estimated from a coupled analysis of the available thermodynamic data and phase diagrams. Simple binary eutectic systems with and without terminal solid solutions, binary eutectics with congruent melting intermediate phases, and ternary eutectic systems were considered. Several combinations of salts were identified, most notable the eutectics LiF-22CaF2 and NaF-60MgF2 which melt at 1039 and 1273 K respectively which posses relatively high heats of fusion/gm (greater than 0.7 kJ/g). Such systems would seemingly be ideal candidates for the light weight, high energy storage media required by the thermal energy storage unit in advanced solar dynamic power systems envisioned for the future space missions.

Misra, A. K.↗
NASA NTRS1993

Solid Lubricant For Alumina

Outer layer of silver lubricates, while intermediate layer of titanium ensures adhesion. Lubricating outer films of silver deposited on thin intermediate films of titanium on alumina substrates found to reduce sliding friction and wear. Films provide effective lubrication for ceramic seals, bearings, and other hot sliding components in advanced high-temperature engines.

Dellacorte, Christopher↗
NASA NTRS1988

Reaction kinetics between fiber and matrix

Interdiffusion and interdiffusion controlled intermediate phase formation in metal matrix composites can be of interest for the prolonged application of these systems at high temperatures. Methods are discussed that address the kinetics of interdiffusion in systems that exhibit solid solution intermixing or the formation of a third intermediate phase at the fiber/matrix interface, or both. The tungsten fiber reinforced niobium and tungsten fiber reinforced superalloy systems are employed as model systems for experimentation and discussion. In an effort to impede interdiffusion, the concept of ion implanted diffusion barriers have been examined. Preliminary results on the feasibility and effectiveness of ion implanted diffusion barriers are presented.

Kopp, M. W.↗
NASA NTRS1985

Solid-state Bonding of Superplastic Aluminum Alloy 7475 Sheet

Experimental works were carried out to study the feasibility of solid state bonding of superplastic aluminum 7475 sheet. Amount of deformation, bonding time, surface cleaning method and intermediate layer were the process parameters investigated. Other parameters, held constant by the superplastic forming condition which is required to obtain a concurrent solid state bonding, are bonding temperature, bonding pressure and atmosphere. Bond integrity was evaluated through metallographic examination, X-ray line scan analysis, SEM fractographic analysis and lap shear tests. The early results of the development program indicated that sound solid state bonding was accomplished for this high strength 7475 alloy with significant amounts of deformation. A thin intermediate layer of the soft 5052 aluminum alloy aided in achieving a solid state bonding by reducing the required amount of plastic deformation at the interface. Bond strength was substantially increased by a post bond heat treatment.

Byun, T. D. S.↗
DOE OSTI2025

Heterointercalation in Chevrel-Phase Sulfides: A Model Periodic Solid for the Investigation of Chain Electron Transfer

Modulation of electron density localization on periodic crystal solids through electron transfer from interstitial cations can directly influence the bonding configurations of small-molecule intermediates at the catalyst binding site. This study presents the microwave-assisted solid-state synthesis of four heterointercalant Chevrel-phase (CP) sulfides with varying metal cation intercalants with compositional and electronic structure investigations of the electron density redistribution as a result of intercalation. The heterointercalant CP sulfides, with the general formula Cu x M y Mo 6 S 8 (where M = Cr, Mn, Fe, Ni; x, y = 1.5−2.5), are presented here for the probe reaction of electrochemical CO 2 reduction. A change in product selectivity is observed toward the production of methanol at low overpotentials of −0.5 V vs reversible hydrogen electrode (RHE), as a result of the intercalant combination present within the CP interstitial cavity. Structural confirmation of all materials was examined through Rietveld refinement of the powder X-ray diffraction (PXRD) data, high-resolution transmission electron microscopy (HR-TEM), and selected-area electron diffraction (SAED). Electron transfer from the intercalated metal cations to the Mo 6 S 8 cluster was investigated via X-ray photoelectron spectroscopy (XPS) of the intercalated metal cations and the chalcogenide cluster. Electron transfer was further confirmed through X-ray absorption analysis (XAS) of the K-edges of Mo and intercalants. Intermediate studies of electrochemical reduction of formaldehyde to methanol resulted in a faradaic efficiency of ∼78% methanol production on Cu x Ni y Mo 6 S 8 . The results presented herein identify distinct principles for materials design that can be utilized in other compositional spaces within the broad families of periodic crystal solids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Electric Field’s Dueling Effects through Dehydration and Ion Separation in Driving NaCl Nucleation at Charged Nanoconfined Interfaces

Investigating nucleation in charged nanoconfined environments under electric fields is crucial for many scientific and engineering applications. Here we study the nucleation of NaCl from aqueous solution near charged surfaces using machine-learning-augmented enhanced sampling molecular dynamics simulations. Our simulations successfully drive phase transitions between the liquid and solid phases of NaCl. The solid phase is stabilized under electric fields, particularly at an intermediate surface charge density. We examine which physical characteristics drive the nucleation of NaCl from aqueous solutions and find that the removal of solvent water from Cl– at the solid precursor surface plays a more critical role than the accumulation of ions. Our simulations reveal the competing effects of electric fields on nucleation processes: they facilitate the removal of water, promoting nucleation, but also promote the separation of ion pairs, thereby hindering nucleation. Here, this work provides a framework for studying nucleation processes in nanoconfined environments under electric fields and provides physical insights for the design of electrochemistry materials.

Electric fields↗
DOE OSTI2026

Aliovalent gallium dopants remove Ti 3+ defects and improve photocatalytic and photoelectrochemical water oxidation properties of LaTiO 2 N

LaTiO 2 N is a promising semiconductor for the water splitting reaction due to its 2.1 eV band gap and stability against corrosion. However, its solar energy conversion is limited by Ti 3+ recombination defects introduced during ammonolysis. Here we show for the first time that Ti 3+ defects in LaTiO 2 N can be suppressed with incorporation of 2, 5, and 10% aliovalent gallium (Ga 3+ ) dopants during synthesis via the layered La 2 Ti 2 O 7 intermediate. Electron paramagnetic resonance (EPR) spectroscopy on the solid powders confirms a reduction in the Ti 3+ donor density from 2.97 × 10 17 cm −3 for the non-doped material to ∼6.24 × 10 16 cm −3 for 5% Ga-doped LaTiO 2 N. The remaining Ti 3+ defects are concentrated near the LaTiO 2 N surface, according to X-ray photoelectron spectroscopy. The defect reduction shifts the optical absorption edge from 2.02 to 2.09 eV and eliminates a broad absorption band at 1050 nm from the optical absorption spectra. It also removes a 1.0–1.7 eV sub-band gap photovoltage signal from surface photovoltage spectra. This suggests that empty Ti 3+ d-orbitals are located 1.0–1.7 eV above the LaTiO 2 N valence band edge. Removing these recombination states with increasing Ga 3+ content enhances the photoconversion efficiency of LaTiO 2 N during water oxidation. The optimized 2 wt% CoO x -loaded 5% Ga-doped LaTi O2 N material has a 16% AQE (400 nm) for O 2 production from aqueous silver nitrate solution and a ∼2.1 mA cm −2 water oxidation photocurrent at 1.23 V under 100 mW cm −2 Xe arc lamp illumination. The water oxidation photocurrent is stable during a 50 min test, and the Faraday efficiency for O 2 generation is 97%, confirming short-term corrosion stability of LaTiO 2 N. Altogether, these results provide a better understanding of the distribution, concentration, and impact of Ti 3+ defects on the optical, photovoltage, and photoelectrochemical properties of LaTiO 2 N. In combination with other defect control strategies, aliovalent Ga 3+ doping can help bring the solar energy conversion efficiency of LaTiO 2 N closer to the theoretical limit.

Wang, Li [University of California, Davis, CA (Uni↗
DOE OSTI2025

In-situ/operando study of Cu-based nanocatalysts for CO 2 electroreduction using electrochemical liquid cell TEM

The structure of a nanocatalyst during electrocatalytic reactions often deviates from its pristine structure due to intrinsic properties, or physical and chemical adsorption at the catalytic surfaces. Taking Cu-based catalysts for CO 2 electroreduction reactions (CO 2 RR) as an example, they often experience segregation, leaching, and alloying during reactions. With the recent breakthrough development of high-resolution polymer electrochemical liquid cells, in-situ electrochemical liquid cell transmission electron microscopy (EC-TEM) alongside other advanced microscopy techniques, has become a powerful platform for revealing electrocatalysts restructuring at the atomic level. Considering the complex reactions involving electrified solid-liquid interfaces and catalyst structural evolution with intermediates, systematic studies with multimodal approaches are crucial. In this article, we demonstrate a research protocol for the study of electrocatalysts structural evolution during reactions using the in-situ EC-TEM platform. Using Cu and CuAg nanowire catalysts for CO 2 RR as model systems, we describe the experimental procedures and findings. We highlight the platform’s crucial role in elucidating atomic-scale pathways of nanocatalyst restructuring and identifying catalytic active sites, as well as avoiding potential artifacts to ensure unbiased conclusions. Using the multimodal characterization toolbox, we provide the opportunity to correlate the structure of a working catalyst with its performance. Finally, we discuss advancements as well as the remaining gap in elucidating the structural-performance relationship of working catalysts. We expect this article will assist in establishing guidelines for future investigations of complex electrochemical reactions, such as CO 2 RR and other catalytic processes, using the in-situ EC-TEM platform.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Techno-economics of hydrocarbon fuel production and recyclables recovery from landfill-destined municipal solid waste: AI-enhanced materials recovery facility design

Sustainable aviation fuels (SAF) production from cellulosic paper fractions of municipal solid waste (MSW) destined for landfills has strong potential to advance environmental, social, and economic sustainability across the aviation and waste sectors. This study proposes an artificial intelligence-enabled material recovery facility (AI-MRF) design to efficiently characterize, separate, process, and convert recovered paper waste from MSW into intermediate chemicals and SAF. The AI-MRF, designed to process 233,091 metric tons of MSW annually, integrates smart manufacturing technologies including AI, visual and hyperspectral imaging, multi-sensor data, and traditional sorting systems. Well-characterized and sorted cellulosic paper waste was utilized for chemical and fuel production scenarios, while clean plastics, metals, and glass were considered for recycling. Conversion of paper waste into intermediate sugars achieved a net present value (NPV) of up to $\$67$ million. For sugar-to-SAF production scenarios, the minimum fuel selling price (MFSP) was calculated at $\$6.11$ per gasoline gallon equivalent (GGE) when excluding recyclable revenue, and $\$4.03$ per GGE when halving recyclable revenue. The MFSP was further reduced to $\$1.96$ per GGE when accounting for SAF sales and recyclables. Nationally, this approach could yield about 2 billion GGE of hydrocarbon fuel annually from available MSW in the United States.

09 BIOMASS FUELS↗
NASA NTRS1993

X-ray observations of EX Hydrae with the Einstein Solid State Spectrometer

Einstein SSS X-ray observations of the eclipsing intermediate polar EX Hya are presented. The SSS data have a better resolution at energies extending below 2 keV than do the EXOSAT data. These data reveal the presence of a soft component with a temperature of about 0.74 keV. The phase-resolved data can be fitted to a model of two-temperature thermal plasma with a single absorber, with the result that only the normalization varies with phase. This suggests that part of the soft component might become occulted at minimum. If we assume that the reduction in the flux occurs due to the photoelectric absorption, we find that a high-density material covering only about 40 percent of the emission can fit the data equally well. The EXOSAT and Ginga data of this source favor the accretion curtain model rather than the occultation model. We modify the accretion curtain model by assuming that the modulation is caused by an absorber which partially covers the accreting column at the minimum of the 67-min pulse. An emission line at 1.72 keV is present in the data. The equivalent width of this line varies in phase with the continuum. We associate this line with Si fluorescence.

Singh, Jyoti↗
DOE OSTI2026

Toward durable stacks: glass-ceramic sealants for intermediate-temperature protonic ceramic electrochemical systems

Protonic ceramic electrochemical cells (PCECs) are emerging as promising technologies for efficient energy conversion and hydrogen production because they operate at intermediate temperatures with improved efficiency and durability compared with conventional solid oxide electrochemical cells. However, the long-term reliability and commercialization of PCEC stacks remain strongly limited by the performance of sealants, which are required to maintain gas tightness, electrical insulation, and mechanical integrity under harsh thermal and chemical environments. Among various sealing approaches, glass-ceramic sealants are considered the most practical and scalable due to their excellent wettability, chemical tunability, and strong interfacial adhesion. This review provides a comprehensive overview of recent advances in glass-ceramic sealants for intermediate-temperature protonic ceramic electrochemical systems. The fundamental design principles of sealant compositions are first discussed, followed by recent developments in deposition methods, sintering strategies, surface treatments, and degradation monitoring techniques. Particular attention is given to the unique challenges associated with PCEC operating conditions, including hydrothermal degradation, interfacial reactions with barium-containing electrolytes, and thermal mismatch. Finally, future opportunities involving sustainable materials, multiscale modeling, additive manufacturing, and artificial intelligence-assisted sealant optimization are highlighted.

glass–ceramic sealants↗
NASA NTRS1983

Investigation of a para-ortho hydrogen reactor for application to spacecraft sensor cooling

The utilization of solid hydrogen in space for sensor and instrument cooling is a very efficient technique for long term cooling or for cooling at high heat rates. The solid hydrogen can provide temperatures as low as 7 to 8 K to instruments. Vapor cooling is utilized to reduce parasitic heat inputs to the 7 to 8 K stage and is effective in providing intermediate cooling for instrument components operating at higher temperatures. The use of solid hydrogen in place of helium may lead to weight reductions as large as a factor of ten and an attendent reduction in system volume. The results of an investigation of a catalytic reactor for use with a solid hydrogen cooling system is presented. Trade studies were performed on several configurations of reactor to meet the requirements of high reactor efficiency with low pressure drop. Results for the selected reactor design are presented for both liquid hydrogen systems operating at near atmospheric pressure and the solid hydrogen cooler operating as low as 1 torr.

Nast, T. C.↗
DOE OSTI2025

Unveiling phase evolution of complex oxides toward precise solid-state synthesis

The precise synthesis of high-purity materials is crucial in accelerating materials discovery. However, the lack of theoretical understanding and practical guidance poses challenges, particularly for materials with compositional and structural complexity. Here, we propose a feasible principle toward synthesizing complex inorganic solids. This principle involves the introduction of an inducer that induces crucial intermediates, which in turn guide the synthesis pathway toward the target materials through structural templating, named inducer-facilitated assembly through structural templating (i-FAST). We validate this principle with three distinct oxides: garnet Li6.5La3Zr1.5Ta0.5O12, perovskite BaCo0.8Sn0.2O3, and pyrochlore Gd1.5La0.5Zr2O7. This structural templating approach enables synthesis along predesigned pathways, forming intermediates that are thermodynamically favored for prior formation and kinetically preferred for the final product, resulting in precisely synthesizing high-purity target materials. This study not only represents a substantial advancement in comprehending the interplay between thermodynamics/kinetics and phase evolution in complex solid synthesis but also provides an effective strategy for guiding exploratory solid-state synthesis.

Yang, Lin↗