Search NASA⌕ Search

SEARCH · Search NASA

Results for “j×B force”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Computer simulation of plasma and N-body problems

The following FORTRAN language computer codes are presented: (1) efficient two- and three-dimensional central force potential solvers; (2) a three-dimensional simulator of an isolated galaxy which incorporates the potential solver; (3) a two-dimensional particle-in-cell simulator of the Jeans instability in an infinite self-gravitating compressible gas; and (4) a two-dimensional particle-in-cell simulator of a rotating self-gravitating compressible gaseous system of which rectangular coordinate and superior polar coordinate versions were written.

Harries, W. L.↗

NASTRAN solutions of problems described by simultaneous parabolic differential equations

NASTRAN solution techniques are shown for a numerical analysis of a class of coupled vector flow processes described by simultaneous parabolic differential equations. To define one physical problem type where equations of this form arise, the differential equations describing the coupled transfers of heat and mass in mechanical equilibrium with negligible mass average velocity are presented and discussed. Also shown are the equations describing seepage when both electrokinetic and hydrodynamic forces occur. Based on a variational statement of the general problem type, the concepts of scalar transfer elements and parallel element systems are introduced. It is shown that adoptation of these concepts allows the direct use of NASTRAN's existing Laplace type elements for uncoupled flow (the heat transfer elements) for treating multicomponent coupled transfer. Sample problems are included which demonstrate the application of these techniques for both steady-state and transient problems.

Mason, J. B.↗

Tank Tests of the Effect of Rivet Heads, etc., on the Water Performance of a Seaplane Float, Special Report

A 1/3.5 full-size model of the Mark V float of the Bureau of Aeronautics, Navy Department, was tested in the NACA tank both with smooth painted bottom surfaces and with roundhead rivets, plate laps, and keel plates fitted to simulate the actual bottom of a metal float. The augmentation in water resistance due to the added roughness was found to be from 10-12% at the hum speed and from 12-14% at high speeds. The effect of the roughness of the afterbody was found to be negligible except at high trims. The model data were extrapolated to full size by the usual method which assumes the forces to vary according to Froude's law, and in the case of the smooth model by a method of separation that takes into account the effect of scale on the frictional resistance. It was concluded that the effect of rivet heads on the takeoff performance of a relatively high-powered float seaplane is of little consequence but that it may be of greater importance in the case of more moderately powered flying boats.

Parkinson, J. B.↗

Tank Tests to Show the Effect Rivet Heads on the Water Performance of a Seaplane-Float

A 1/3.5 full-sized model of a seaplane float constructed from lines supplied by the Bureau of Aeronautics, Navy Department, was tested first with smooth painted bottom surfaces and then with round-head rivets, plate laps, and keel plates fitted to simulate the actual bottom of a metal float. A percentage increase in water resistance caused by the added roughness was found to be from 5 to 20 percent at the hump speed and from 15 to 40 percent at high speeds. The effect of the roughness of the afterbody was found to be negligible except at high trims. The model data were extrapolated to full size by the usual method that assumes the forces to vary according to Froude's law and, in the case of the smooth model, by a method of separation that takes into account the effect of scale on the frictional resistance. It was concluded that the effect of rivet heads on the take-off performance of a relatively high-powered float seaplane is of little consequence, but it may be of greater importance in the case of more moderately powered flying boats.

FLOATS - RESISTANCE EFFECT OF SURFACE ROUGHNESS↗

Elasticity of excised dog lung parenchyma

An optical-electromechanical system is used to measure the force-deformation behavior of biaxially loaded rectangular slabs of excised dog lung parenchyma. In the course of the study, the effects of time, the consistency of reference lengths and areas, the presence of hysteresis, the necessity of preconditioning, the repeatability of results, the effects of lateral load, the effect of strain rate, the effect of pH, the influence of temperature, and the variations among specimens are considered. A new finding is that there is a change in elastic behavior when the tissue undergoes a compressive strain. When the tissue is in tension, increasing the lateral load decreases the compliance, whereas the opposite is true when compressive strain is present.

Vawter, D. L.↗

Baseline meteorological soundings for parametric environmental investigations at Kennedy Space Center and Vandenberg Air Force Base

Meteorological soundings representative of the atmospheric environment at the Kennedy Space Center, Florida and Vandenberg Air Force Base, California, are presented. Synthetic meteorological soundings at Kennedy Space Center, including fall, spring, and a sea breeze, and at Vandenberg Air Force Base (sea breeze with low and high level inversion and stationary upper level troughs) are shown. Soundings of frontal passages are listed. The Titan launch soundings at Kennedy Space Center present a wide range of meteorological conditions, both seasonal and time of day variations. The meteorological data input of altitude, wind speed, wind direction, temperature, and pressure may be used as meteorological inputs for the NASA/MSFC Multilayer Diffusion Model or other models to obtain quantitative estimates of effluent concentrations associated with the potential emission of major combustion products in the lower atmosphere to simulate actual launches of space vehicles. The Titan launch soundings are also of value in terms of rocket effluent measurements for analysis purposes.

Susko, M.↗

Longitudinal and lateral static stability and control characteristics of a 1/6-scale model of a remotely piloted research vehicle with a supercritical wing

An investigation was conducted in the Langley 8-foot transonic pressure tunnel to determine the longitudinal and lateral-directional static stability and control characteristics of a 1/6-scale force model of a remotely piloted research vehicle. The model was equipped with a supercritical wing and employed elevons for pitch and roll control. Test conditions were as follows: Reynolds number of about 6.6 x 10 to the 6th power per meter, variations of sideslip from -6 deg to 6 deg, elevon deflection angle (symmetrically and asymmetrically) from -9 deg to 3 deg, and rudder deflection angle from 0 deg to -10 deg. The model was longitudinally statically stable at angles of attack up to about 7 deg, which is significantly greater than the angle of attack for the cruise condition (approximately 4 deg). In the range of test Mach numbers, the model was directionally stable and had positive effective dihedral, sufficient pitch control, and positive effectiveness of roll and yaw control.

Byrdsong, T. A.↗

Supersonic aerodynamic damping and oscillatory stability in pitch and yaw fro a model of a variable-sweep fighter airplane with twin vertical tails

Wind-tunnel measurements of the aerodynamic damping and oscillatory in pitch and yaw for a 1/22-scale model of a proposed carrier-based variable-sweep fighter airplane have been made by using a small-amplitude forced-oscillation technique. Tests were made with a wing leading-edge sweep angle of 68 deg at angles of attack from about -1.5 deg to 15.6 deg at a Mach number of 1.60 and at angles of attack from about -3 deg to 21 deg at Mach numbers of 2.02 and 2.36. The results of the investigation indicate that the basic configuration has positive damping and positive oscillatory stability in pitch for all test conditions. In yaw, the damping is generally positive except near an angle of attack of 0 deg at a Mach number of 1.60. The oscillatory stability in yaw is positive except at angles of attack above 16 deg at Mach numbers of 2.02 and 2.36. The addition of external stores generally causes increases in both pitch and yaw damping. The oscillatory stability in pitch is reduced throughout the angle-of-attack range by the addition of the external stores. The effect of adding stores on the oscillatory stability in yaw is a function of angle of attack and Mach number. The effect of changing horizontal-tail incidence on the pitch parameters is also very dependent on angle of attack and Mach number.

Kilgore, R. A.↗

Titan/Centaur T/C-1 post flight evaluation report

The first Titan/Centaur launch vehicle, TC-1, was launched from the Eastern Test Range Complex 41 at 09:48:01.46 hours Eastern Daylight Time on February 11, 1974. The vehicle carried a dynamic mass model of the Viking spacecraft and a SPHINX spacecraft, intended to study high voltage interactions in space. This launch was a Proof Flight of a vehicle con- figuration integrating the Air Force Titan booster and the NASA Centaur upper stage. It also was the first flight of the Centaur Standard Shroud developed for the Titan/Centaur. The countdown for the launch proceeded normally except for an additional 45 minute hold which was required to resolve a question concerning interpretation of booster hydraulic system data. The launch window opened at 09:03:00 hours Eastern Daylight Time. The vehicle was launched o on a flight azimuth of 105°. The Titan boost phase of flight was satisfactory. Solid Motor operation, Stage I and Stage II operation were normal. Venting of the Centaur Standard Shroud during ascent was successful and shroud separation and jettison was accomplished without incident. At the completion of the Titan Stage II burn, the Centaur successfully separated from the Titan. At this time, the Centaur main engines were sequenced through the first planned starting cycle but failed to achieve steady state operation. The vehicle flight control system, not sensing vehicle acceleration, commanded engine shutdown, and recycled, as programmed, through a back-up engine start attempt. The second engine start attempt was also unsuccessful. The flight control system then placed the vehicle in a coast-phase mode and the vehicle continued downrange in free fall. The vehicle was destroyed by Range Safety when the impact point was approximately 2200 nautical miles downrange, 12 minutes, 28.5 seconds after liftoff.

S. V. Szabo, Jr.↗

Particle motion in atmospheric boundary layers of Mars and Earth

To study the eolian mechanics of saltating particles, both an experimental investigation of the flow field around a model crater in an atmospheric boundary layer wind tunnel and numerical solutions of the two- and three-dimensional equations of motion of a single particle under the influence of a turbulent boundary layer were conducted. Two-dimensional particle motion was calculated for flow near the surfaces of both Earth and Mars. For the case of Earth both a turbulent boundary layer with a viscous sublayer and one without were calculated. For the case of Mars it was only necessary to calculate turbulent boundary layer flow with a laminar sublayer because of the low values of friction Reynolds number; however, it was necessary to include the effects of slip flow on a particle caused by the rarefied Martian atmosphere. In the equations of motion the lift force functions were developed to act on a single particle only in the laminar sublayer or a corresponding small region of high shear near the surface for a fully turbulent boundary layer. The lift force functions were developed from the analytical work by Saffman concerning the lift force acting on a particle in simple shear flow.

White, B. R.↗

Estimated grain saltation in a Martian atmosphere

The aeolian mechanics of saltating grains on Mars is studied using both an experimental investigation in an atmospheric wind tunnel and numerical solutions to the equations of motion of a single grain under Martian surface conditions. Numerical solutions for terrestrial conditions are empirically correlated with experimental data for Mars, and the modified equations are solved to estimate Martian grain motion. The calculations demonstrate the importance of a lifting force in initiating grain motion on both planets. It is found that Martian grain-trajectory length scales are longer than those on earth and fall with a higher terminal grain velocity. The wind-tunnel experiments show that saltating grains have an enhanced erosive capability in crater wakes. It is suggested that this enhanced capability may well explain the streaks associated with craters in certain regions on the Martian surface.

White, B. R.↗

A long-lived coronal X-ray arcade

A large, long-lived, soft X-ray emitting arch system observed during a Skylab mission is analyzed. The supposition is that these arches owe their stability to the stable coronal magnetic-field configuration. A global constant alpha force-free magnetic field analysis, is used to describe the arches which stayed in the same approximate position for several solar rotations. A marked resemblance is noted between the theoretical magnetic field configuration and the observed X-ray emmitting feature.

Mcguire, J. P.↗

Saltation threshold on Mars - The effect of interparticle force, surface roughness, and low atmospheric density

Results are reported for wind-tunnel experiments performed to determine the threshold friction speed of particles with different densities. Experimentally determined threshold speeds are plotted as a function of particle diameter and in terms of threshold parameter vs particle friction Reynolds number. The curves are compared with those of previous experiments, and an A-B curve is plotted to show differences in threshold speed due to differences in size distributions and particle shapes. Effects of particle diameter are investigated, an expression for threshold speed is derived by considering the equilibrium forces acting on a single particle, and other approximately valid expressions are evaluated. It is shown that the assumption of universality of the A-B curve is in error at very low pressures for small particles and that only predictions which take account of both Reynolds number and effects of interparticle forces yield reasonable agreement with experimental data. Effects of nonerodible surface roughness are examined, and threshold speeds computed with allowance for this factor are compared with experimental values. Threshold friction speeds on Mars are then estimated for a surface pressure of 5 mbar, taking into account all the factors considered.

Iversen, J. D.↗

Estimated grain saltation in a Martian atmosphere

Mariner 9 spacecraft images showing evidence of variable surface features and surface erosion resulting from atmospheric wind on Mars have caused a renewed interest in the eolian mechanics of saltating grains. To study this phenomenon, both experimental investigation in an atmospheric wind tunnel and numerical solutions of the equations of motion of a single grain under Martian surface conditions were conducted. The numerical solutions for earth were used and empirically adjusted to correlate with existing experimental data for Mars. These modified equations were then solved to estimate grain motion for Mars. These calculations show the importance of a lifting force on the grain to initiate motion in both earth and Mars calculations. Major findings include a comparison of earth and Mars grain trajectories that show Mars length scales to be longer and to fall with a higher terminal grain velocity. The grains in the Mars calculation also made a smaller collision angle with the surface on rebound.

White, B. R.↗

Windblown dust on earth, Mars and Venus

Attempts to predict threshold speeds for windblown dust and sand on Mars and Venus have raised new questions about the mechanism of soil and sand transport by wind. Estimates of threshold speeds on Mars and Venus are made including the effects of both Reynolds number and interparticle forces of cohesion. The current estimates show lower threshold speeds for small particles than previous estimates by Hess, who assumed that Reynolds number is the only important parameter. These estimates, on the other hand, show somewhat higher threshold speeds than those of Sagan and Bagnold, who assumed that the particles are cohesionless. An optimum particle size results, for which threshold speed is a minimum, contrary to Sagan and Bagnold's prediction.

Iversen, J. D.↗

A long-lived coronal arch system observed in X-rays

A large long-lived soft X-ray emitting arch system was observed during the last Skylab mission. This arcade stayed in the same approximate position for several solar rotations. It is suggested that these long-lived arches owe their stability to the stable coronal magnetic-field configuration. A global constant-alpha force-free magnetic-field analysis, as developed by Nakagawa et al. (1977), is used to describe the arches, and results in a marked resemblance between the theoretical magnetic-field configuration and the observed X-ray emitting feature.

Mcguire, J. P.↗

A study of the drooped leading edge airfoil

Wind tunnel tests were conducted to examine various aspects of the drooped-leading edge airfoil which reduces the tendency for an airplane to enter a spin after stall occurs. Three baseline models were used for tests of two dimensional models: NACA 0015, 0014.6, and 0014.2. The 14.6% and 14.2% models were derived from NACA 0015 sections by increasing the chord and matching the profiles aft section. Force, balance data (lift, drag, pitching moment) were obtained for each model at a free-steam Reynold's number of 2.66 x 10 to the 6th power/m. In addition, oil flow visualization tests were performed at various angles of attack. An existing NACA 64 sub 1 A211 airfoil was used in a second series of tests. The leading edge flap was segmented in three parts which allowed various baseline/drooped leading edge configurations to be tested. Force balance and flow visualization tests were completer at chord Renolds numbers of 0.44 x 10 to the 6th power, 1.4 x 10 to the 6th power, and 2.11 x 10 to the 6th power. Test results are included.

Anderson, J. D., Jr.↗

A numerical model of the Martian polar cap winds

An investigation of the Martian polar cap winds and their response to a variety of factors is carried out by numerical experiments based on a zonally symmetric primitive equation model. The seasonal thermal forcing, mass exchange between polar caps and atmosphere, large-scale topography, and polar cap size are discussed, noting that topography has a small effect, but the circulation intensity increases with cap size. The model results show that surface winds near the edge of a retreating polar cap are enhanced, and that the surficial wind indicators near the south pole are formed during spring and those near the north pole during winter. It is suggested that the high-latitude dune fields in the northern hemisphere are formed when the terrain is covered by frost, and that the saltating particles are 'snowflakes' which formed by the mechanism proposed by Pollack (1976). The model results for the winter simulation compare favorably with general circulation model (GCM) calculations.

Haberle, R. M.↗